The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.

The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level.  In most cases, SM
failover doesn't cause LID change so traffic won't stop.  In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state.  In fact, preventing the device from
going down saves packets that otherwise would be lost.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This gives ehca an autogenerated modalias and therefore enables automatic loading.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add "ipoib_use_lro" module parameter to enable LRO and an
"ipoib_lro_max_aggr" module parameter to set the max number of packets
to be aggregated.  Make LRO controllable and LRO statistics accessible
through ethtool.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device.  This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This patch also adds a creation flag for QPs,
IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK, which when set means that
multicast sends from the QP to a group that the QP is attached to will
not be looped back to the QP's receive queue.  This can be used to
save receive resources when a consumer does not want a local copy of
multicast traffic; for example IPoIB must waste CPU time throwing away
such local copies of multicast traffic.

This patch also adds a device capability flag that shows whether a
device supports this feature or not.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

- Add a new rdma ctl command called RDMA_GET_MIB to the cxgb3 low
  level driver to obtain the protocol mib from the rnic hardware.

- Add new iw_cxgb3 provider method to get the MIB from the low level
  driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This patch adds a sysfs attribute group called "proto_stats" under
/sys/class/infiniband/$device/ and populates this group with protocol
statistics if they exist for a given device.  Currently, only iWARP
stats are defined, but the code is designed to allow InfiniBand
protocol stats if they become available.  These stats are per-device
and more importantly -not- per port.

Details:

- Add union rdma_protocol_stats in ib_verbs.h.  This union allows
  defining transport-specific stats.  Currently only iwarp stats are
  defined.

- Add struct iw_protocol_stats to define the current set of iwarp
  protocol stats.

- Add new ib_device method called get_proto_stats() to return protocol
  statistics.

- Add logic in core/sysfs.c to create iwarp protocol stats attributes
  if the device is an RNIC and has a get_proto_stats() method.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.

Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().

Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>

The members struct iwch_rnic_attributes.vendor_id and .vendor_part_id
are write-only, so we might as well get rid of them.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>

- set fw_ver
- set hw_ver
- set max_qp_wr to something reasonable
- set max_cqe to something reasonable
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

During corner case testing, we noticed that some versions of ehca do
not properly transition to interrupt done in special load situations.
This can be resolved by periodically triggering EOI through H_EOI, if
EQEs are pending.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Commit 65adfa91 ("IB/mlx4: Fix RESET to RESET and RESET to ERROR
transitions") added some extra code to handle a QP state transition
from RESET to ERROR.  However, the latest 1.2.1 version of the IB spec
has clarified that this transition is actually not allowed, so we can
remove this extra code again.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Commit b18aad71 ("IB/mthca: Fix RESET to ERROR transition") added some
extra code to handle a QP state transition from RESET to ERROR.
However, the latest 1.2.1 version of the IB spec has clarified that
this transition is actually not allowed, so we can remove this extra
code again.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

I was reviewing the QP state transition diagram in the IB 1.2.1 spec
and the code for qp_state_table[], and noticed that the code allows a
QP to be modified from IB_QPS_RESET to IB_QPS_ERR whereas the notes
for figure 124 (pg 457) specifically says that this transition isn't
allowed.  This is a clarification from earlier versions of the IB
spec, which were ambiguous in this area and suggested that the RESET
to ERR transition was allowed.

Fix up the qp_state_table[] to make RESET->ERR not allowed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

ConnectX HCAs support the IB_MGMT_CLASS_CONG_MGMT management class, so
process MADs of this class through the MAD_IFC firmware command.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

ConnectX returns the max message size it supports through the
QUERY_DEV_CAP firmware command.  When modifying a QP to RTR, the max
message size for the QP must be specified.  This value must not exceed
the value declared through QUERY_DEV_CAP.  The current code ignores
the max allowed size and unconditionally sets the value to 2^31.  This
patch sets all QPs to the max value allowed as returned from firmware.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

- set IB_DEVICE_MEM_MGT_EXTENSIONS capability bit if fw supports it.
- set max_fast_reg_page_list_len device attribute.
- add iwch_alloc_fast_reg_mr function.
- add iwch_alloc_fastreg_pbl
- add iwch_free_fastreg_pbl
- adjust the WQ depth for kernel mode work queues to account for
  fastreg possibly taking 2 WR slots.
- add fastreg_mr work request support.
- add local_inv work request support.
- add send_with_inv and send_with_se_inv work request support.
- removed useless duplicate enums/defines for TPT/MW/MR stuff.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This patch adds support for the IB "base memory management extension"
(BMME) and the equivalent iWARP operations (which the iWARP verbs
mandates all devices must implement).  The new operations are:

 - Allocate an ib_mr for use in fast register work requests.

 - Allocate/free a physical buffer lists for use in fast register work
   requests.  This allows device drivers to allocate this memory as
   needed for use in posting send requests (eg via dma_alloc_coherent).

 - New send queue work requests:
   * send with remote invalidate
   * fast register memory region
   * local invalidate memory region
   * RDMA read with invalidate local memory region (iWARP only)

Consumer interface details:

 - A new device capability flag IB_DEVICE_MEM_MGT_EXTENSIONS is added
   to indicate device support for these features.

 - New send work request opcodes IB_WR_FAST_REG_MR, IB_WR_LOCAL_INV,
   IB_WR_RDMA_READ_WITH_INV are added.

 - A new consumer API function, ib_alloc_mr() is added to allocate
   fast register memory regions.

 - New consumer API functions, ib_alloc_fast_reg_page_list() and
   ib_free_fast_reg_page_list() are added to allocate and free
   device-specific memory for fast registration page lists.

 - A new consumer API function, ib_update_fast_reg_key(), is added to
   allow the key portion of the R_Key and L_Key of a fast registration
   MR to be updated.  Consumers call this if desired before posting
   a IB_WR_FAST_REG_MR work request.

Consumers can use this as follows:

 - MR is allocated with ib_alloc_mr().

 - Page list memory is allocated with ib_alloc_fast_reg_page_list().

 - MR R_Key/L_Key "key" field is updated with ib_update_fast_reg_key().

 - MR made VALID and bound to a specific page list via
   ib_post_send(IB_WR_FAST_REG_MR)

 - MR made INVALID via ib_post_send(IB_WR_LOCAL_INV),
   ib_post_send(IB_WR_RDMA_READ_WITH_INV) or an incoming send with
   invalidate operation.

 - MR is deallocated with ib_dereg_mr()

 - page lists dealloced via ib_free_fast_reg_page_list().

Applications can allocate a fast register MR once, and then can
repeatedly bind the MR to different physical block lists (PBLs) via
posting work requests to a send queue (SQ).  For each outstanding
MR-to-PBL binding in the SQ pipe, a fast_reg_page_list needs to be
allocated (the fast_reg_page_list is owned by the low-level driver
from the consumer posting a work request until the request completes).
Thus pipelining can be achieved while still allowing device-specific
page_list processing.

The 32-bit fast register memory key/STag is composed of a 24-bit index
and an 8-bit key.  The application can change the key each time it
fast registers thus allowing more control over the peer's use of the
key/STag (ie it can effectively be changed each time the rkey is
rebound to a page list).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow.  It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU.  This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB.  The newly allocated SKB is passed to the stack and the
old SKB is reposted.

When running netperf, UDP small messages, without this pach I get:

    UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
    14.4.3.178 (14.4.3.178) port 0 AF_INET
    Socket  Message  Elapsed      Messages
    Size    Size     Time         Okay Errors   Throughput
    bytes   bytes    secs            #      #   10^6bits/sec

    114688     128   10.00     5142034      0     526.31
    114688           10.00     1130489            115.71

With this patch I get both send and receive at ~315 mbps.

The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced.  As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs.  So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted.  Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets.  This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):

    tx packets
    ==========
    port counter:   1,543,996
    ifconfig:       1,581,426
    netperf:        5,142,034

    rx packets
    ==========
    netperf         1,1304,089
Signed-off-by: Eli Cohen <eli@mellanox.co.il>

They don't get updated by git and so they're worse than useless.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Remove subversion $Id lines and improve readability by fixing other
coding style problems pointed out by checkpatch.pl.
Signed-off-by: Dotan Barak <dotanba@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The idea is that for QPs with fixed size work requests (eg selective
signaling QPs), before stamping the WQE, we read the value of the DS
field, which gives the effective size of the descriptor as used in the
previous post.  Then we stamp only that area, since the rest of the
descriptor is already stamped.

When initializing the send queue buffer, make sure the DS field is
initialized to the max descriptor size so that the subsequent stamping
will be done on the entire descriptor area.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This patch solves a race that occurs after an event occurs that causes
the SA query module to flush its SM address handle (AH).  When SM AH
becomes invalid and needs an update it is handled by the global
workqueue.  On the other hand this event is also handled in the IPoIB
driver by queuing work in the ipoib_workqueue that does multicast
joins.  Although queuing is in the right order, it is done to 2
different workqueues and so there is no guarantee that the first to be
queued is the first to be executed.

This causes a problem because IPoIB may end up sending an request to
the old SM, which will take a long time to time out (since the old SM
is gone); this leads to a much longer than necessary interruption in
multicast traffer.

The patch sets the SA query module's SM AH to NULL when the event
occurs, and until update_sm_ah() is done, any request that needs sm_ah
fails with -EAGAIN return status.

For consumers, the patch doesn't make things worse.  Before the patch,
MADs are sent to the wrong SM so the request gets lost.  Consumers can
be improved if they examine the return code and respond to EAGAIN
properly but even without an improvement the situation is not getting
worse.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The license text for several files references a third software license
that was inadvertently copied in.  Update the license to what was
intended.  This update was based on a request from HP.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Remove an explicit memset(..., 0, ...) of a 'listener' structure
allocated with kzalloc().
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: Faisal Latif <faisal@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The SRP initiator is currently using ib_find_cached_pkey() and
ib_get_cached_gid() in situations where the uncached ib_find_pkey()
and ib_query_gid() functions serve just as well: sleeping is allowed
and performance is not an issue.  Since we want to eliminate the
cached operations in the long term, convert SRP to use the uncached
variants.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

When CONFIG_EXTRA_FIRMWARE_DIR gets changed, the filename in the .S file
(which uses .incbin to include the binary) needs to change. When we
renamed the BUILTIN_FIRMWARE_DIR option to EXTRA_FIRMWARE_DIR, we forgot
to update the manual dependency in firmware/Makefile, so it was
depending on a non-existent file in include/config/
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
  firmware: convert sb16_csp driver to use firmware loader exclusively
  dsp56k: use request_firmware
  edgeport-ti: use request_firmware()
  edgeport: use request_firmware()
  vicam: use request_firmware()
  dabusb: use request_firmware()
  cpia2: use request_firmware()
  ip2: use request_firmware()
  firmware: convert Ambassador ATM driver to request_firmware()
  whiteheat: use request_firmware()
  ti_usb_3410_5052: use request_firmware()
  emi62: use request_firmware()
  emi26: use request_firmware()
  keyspan_pda: use request_firmware()
  keyspan: use request_firmware()
  ttusb-budget: use request_firmware()
  kaweth: use request_firmware()
  smctr: use request_firmware()
  firmware: convert ymfpci driver to use firmware loader exclusively
  firmware: convert maestro3 driver to use firmware loader exclusively
  ...

Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
  [ARM] 5171/1: ep93xx: fix compilation of modules using clocks
  [ARM] 5133/2: at91sam9g20 defconfig file
  [ARM] 5130/4: Support for the at91sam9g20
  [ARM] 5160/1: IOP3XX: gpio/gpiolib support
  [ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
  [ARM] 5084/1: zylonite: Register AC97 device
  [ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
  [ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
  [ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
  [ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
  [ARM] 5144/1: pxaficp_ir: cleanup includes
  [ARM] pxa: remove pxa_set_cken()
  [ARM] pxa: allow clk aliases
  [ARM] Feroceon: don't disable BPU on boot
  [ARM] Orion: LED support for HP mv2120
  [ARM] Orion: add RD88F5181L-FXO support
  [ARM] Orion: add RD88F5181L-GE support
  [ARM] Orion: add Netgear WNR854T support
  [ARM] s3c2410_defconfig: update for current build
  [ARM] Acer n30: Minor style and indentation fixes.
  ...

Conflicts:

	sound/pci/Kconfig

This includes PXA work up to the SPI changes for the initial merge,
since e172274c depends on the SPI
tree being merged.

Conflicts:

	arch/arm/configs/em_x270_defconfig
	arch/arm/configs/xm_x270_defconfig

* 'core/softirq' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softirq: remove irqs_disabled warning from local_bh_enable
  softirq: remove initialization of static per-cpu variable
  Remove argument from open_softirq which is always NULL

* 'core/rodata' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  move BUG_TABLE into RODATA

* 'core/printk' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, generic: mark early_printk as asmlinkage
  printk: export console_drivers
  printk: remember the message level for multi-line output
  printk: refactor processing of line severity tokens
  printk: don't prefer unsuited consoles on registration
  printk: clean up recursion check related static variables
  namespacecheck: more kernel/printk.c fixes
  namespacecheck: fix kernel printk.c

Even the help-text makes it clear that normal people shouldn't enable
it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'core/locking' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  lockdep: fix kernel/fork.c warning
  lockdep: fix ftrace irq tracing false positive
  lockdep: remove duplicate definition of STATIC_LOCKDEP_MAP_INIT
  lockdep: add lock_class information to lock_chain and output it
  lockdep: add lock_class information to lock_chain and output it
  lockdep: output lock_class key instead of address for forward dependency output
  __mutex_lock_common: use signal_pending_state()
  mutex-debug: check mutex magic before owner

Fixed up conflict in kernel/fork.c manually