- 18 Nov, 2010 2 commits
-
-
Bruno Randolf authored
Remove ath5k's private moving average implementation in favour of the generic library version. Signed-off-by:
Bruno Randolf <br1@einfach.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Bruno Randolf authored
This adds generic functions for calculating Exponentially Weighted Moving Averages (EWMA). This implementation makes use of a structure which keeps the EWMA parameters and a scaled up internal representation to reduce rounding errors. The original idea for this implementation came from the rt2x00 driver (rt2x00link.c). I would like to use it in several places in the mac80211 and ath5k code and I hope it can be useful in many other places in the kernel code. Signed-off-by:
KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by:
-
- 17 Nov, 2010 27 commits
-
-
Johannes Berg authored
The code to handle powersaving stations has a race: when the powersave flag is lifted from a station, we could transmit a packet that is being processed for TX at the same time right away, even if there are other frames queued for it. This would cause frame reordering. To fix this, lift the flag only under the appropriate lock that blocks TX. Additionally, the code to allow drivers to block a station while frames for it are on the HW queue is never re-enabled the station, so traffic would get stuck indefinitely. Fix this by clearing the flag for this appropriately. Finally, as an optimisation, don't do anything if the driver unblocks an already unblocked station. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
In many places we've just hardcoded the AC numbers -- which is a relic from the original mac80211 (d80211). Add constants for them so we know what we're talking about. Signed-off-by:
-
Felix Fietkau authored
Some of the new AR9003 cards do not come with an external EEPROM chip anymore. Calibration data on these cards is stored in the OTP ROM on the chip. This patch adds support for reading this data, and also adds support for different EEPROM chip sizes (512 bytes instead of 1K). Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
Since the pointers after the rates in the tx info cannot be used anymore after frames have been queued, this area can be used to store information that was previously stored in the ath_buf. With these changes, we can delay the ath_buf assignment in the aggregation code until aggregates are formed. That will not only make it possible to simplify DMA descriptor setup to do less rewriting of uncached memory, but will also make it easier to move aggregation out of the core of the ath9k tx path. Signed-off-by:
-
Felix Fietkau authored
- remove the BUF_HT flag, and instead check for IEEE80211_TX_CTL_AMPDU before calling ath_tx_send_ampdu. - remove a few unused variables - calculate frame length before adding the frame padding - merge the misnamed ath_tx_start_dma function into ath_tx_start - remove an unused argument for assign_aggr_tid_seqno Signed-off-by:
-
Felix Fietkau authored
This makes further tx path cleanups easier Signed-off-by:
-
Felix Fietkau authored
Merge initial processing for the CAB queue and regular tx. Also move ath_tx_cabq() to beacon.c and make it static. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
RA-Jay Hung authored
When send out skb data to mac80211, orignal code will cause mac80211 unaligned access, so modify code to make mac80211 can natural access. Signed-off-by:
RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
RA-Jay Hung authored
Put the assignment of header_length after pull out extra tx headroom Signed-off-by:
-
RA-Jay Hung authored
rt2800usb chips need to add 1~3 bytes zero padding after each 802.11 header & payload, and at the end need to add 4 bytes zero padding whether doing TX bulk aggregation or not, TXINFO_W0_USB_DMA_TX_PKT_LEN in TXINFO must include 1-3 bytes padding after 802.11 header & payload but do not include 4 bytes end zero padding. In rt2800usb_get_tx_data_len do not consider multiple of the USB packet size case, sometimes this will cause USB DMA problem. Signed-off-by:
-
Gertjan van Wingerde authored
Make the code a bit more portable to architectures that do not support KSEG1ADDR. Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Tested-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
Gertjan van Wingerde authored
CONFIG_RT2800PCI_PCI and CONFIG_RT2800PCI_SOC are strictly not needed as we can check the dependent symbols directly in the rest of Kconfig and the code, so clean up the Kconfig namespace a bit. Signed-off-by:
-
Gertjan van Wingerde authored
Enabling of RT30xx devices via Kconfig variables was introduced when these devices weren't properly supported yet. Now that that they are properly supported and functional, we can remove these Kconfig variables for RT30xx devices and simply enable them whenever rt2800pci and/or rt2800usb is enabled. Signed-off-by:
-
Gertjan van Wingerde authored
General clean up of the Kconfig part for RT28XX devices. Also remove the indications of non functional support for rt27xx/rt28xx/rt30xx devices, as this is no longer true. They just work fine. Finally, remove the experimental indications for rt27xx/rt28xx/rt30xx devices as that is no longer true. Keep the experimental indications for rt33xx/rt35xx devices, though. Signed-off-by:
-
Gertjan van Wingerde authored
Modified from Eddy's patch by adding the RT3370 USB support as well. Signed-off-by:
-
Ivo van Doorn authored
For some hardware the REGISTER_BUSY_COUNT isn't sufficient, increase the REGISTER_BUSY_COUNT to 100 to catch most devices which have more problems with accessing the registers. For normal operating devices nothing would change as they will exit the loop early anyway. Signed-off-by:
-
- 16 Nov, 2010 11 commits
-
-
Mohammed Shafi Shajakhan authored
The calibration data variable size is based on the number of channels available in the ath9k driver. Signed-off-by:
Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by:
-
Stanislaw Gruszka authored
Subtract of jiffies is fine even if one variable overwrap. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Stanislaw Gruszka authored
We can simplify length calculation in iwlagn_tx_skb, that function is enough complex, without fuzz it more than necessary. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Juuso Oikarinen authored
Chipsets with hardware based connection monitoring need to autonomically send directed probe-request frames to the AP (in the event of beacon loss, for example.) For the hardware to be able to do this, it requires a template for the frame to transmit to the AP, filled in with the BSSID and SSID of the AP, but also the supported rate IE's. This patch adds a function to mac80211, which allows the hardware driver to fetch this template after association, so it can be configured to the hardware. Signed-off-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Acked-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Merge ath_tx_send_normal and ath_tx_send_ht_normal. Move the paprd state initialization and sequence number assignment to reduce the number of redundant checks. This not only simplifies buffer allocation error handling, but also removes a small inconsistency in the buffer HT flag. This flag should only be set if the frame is also a QoS data frame. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
