The buffer length field in the ena rx descriptor is 16 bit, and the
current driver passes a full page in each ena rx descriptor.
When PAGE_SIZE equals 64kB or more, the buffer length field becomes
zero.
To solve this issue, limit the ena Rx descriptor to use 16kB even
when allocating 64kB kernel pages. This change would not impact ena
device functionality, as 16kB is still larger than maximum MTU.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with driver version 1.5.0, in case of a surprise device
unplug, there is a race caused by invoking ena_destroy_device()
from two different places. As a result, the readless register might
be accessed after it was destroyed.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the documentation in msg_zerocopy.rst, the SO_ZEROCOPY
flag was introduced because send(2) ignores unknown message flags and
any legacy application which was accidentally passing the equivalent of
MSG_ZEROCOPY earlier should not see any new behaviour.

Before commit f214f915 ("tcp: enable MSG_ZEROCOPY"), a send(2) call
which passed the equivalent of MSG_ZEROCOPY without setting SO_ZEROCOPY
would succeed.  However, after that commit, it fails with -ENOBUFS.  So
it appears that the SO_ZEROCOPY flag fails to fulfill its intended
purpose.  Fix it.

Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When nla_put*() fails after nla_nest_start(), we need
to call nla_nest_cancel() to cancel the message, otherwise
we end up calling nla_nest_end() like a success.

Fixes: 0ed5269f ("net/sched: add tunnel option support to act_tunnel_key")
Cc: Davide Caratti <dcaratti@redhat.com>
Cc: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 822fb18a ("xen-netfront: wait xenbus state change when load
module manually") added a new wait queue to wait on for a state change
when the module is loaded manually. Unfortunately there is no wakeup
anywhere to stop that waiting.

Instead of introducing a new wait queue rename the existing
module_unload_q to module_wq and use it for both purposes (loading and
unloading).

As any state change of the backend might be intended to stop waiting
do the wake_up_all() in any case when netback_changed() is called.

Fixes: 822fb18a ("xen-netfront: wait xenbus state change when load module manually")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3559d81e ("r8169: simplify rtl_hw_start_8169") changed order of
two register writes:
1) Caused RxConfig to be written before TX / RX is enabled,
2) Caused TxConfig to be written before TX / RX is enabled.

At least on XIDs 10000000 ("RTL8169sb/8110sb") and
18000000 ("RTL8169sc/8110sc") such writes are ignored by the chip, leaving
values in these registers intact.

Change 1) was reverted by
commit 05212ba8 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices"),
however change 2) wasn't.

In practice, this caused TxConfig's "InterFrameGap time" and "Max DMA Burst
Size per Tx DMA Burst" bits to be zero dramatically reducing TX performance
(in my tests it dropped from around 500Mbps to around 50Mbps).

This patch fixes the issue by moving TxConfig register write a bit later in
the code so it happens after TX / RX is already enabled.

Fixes: 05212ba8 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>

__tipc_nl_compat_dumpit() uses a netlink_callback on stack,
so the only way to align it with other ->dumpit() call path
is calling tipc_dump_start() and tipc_dump_done() directly
inside it. Otherwise ->dumpit() would always get NULL from
cb->args[].

But tipc_dump_start() uses sock_net(cb->skb->sk) to retrieve
net pointer, the cb->skb here doesn't set skb->sk, the net pointer
is saved in msg->net instead, so introduce a helper function
__tipc_dump_start() to pass in msg->net.

Ying pointed out cb->args[0...3] are already used by other
callbacks on this call path, so we can't use cb->args[0] any
more, use cb->args[4] instead.

Fixes: 9a07efa9 ("tipc: switch to rhashtable iterator")
Reported-and-tested-by: syzbot+e93a2c41f91b8e2c7d9b@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2018-09-05

This pull request contains some fixes for mlx5 etherent netdevice and
core driver.

Please pull and let me know if there's any problem.

For -stable v4.9:
('net/mlx5: Fix debugfs cleanup in the device init/remove flow')

For -stable v4.12:
("net/mlx5: E-Switch, Fix memory leak when creating switchdev mode FDB tables")

For -stable v4.13:
("net/mlx5: Fix use-after-free in self-healing flow")

For -stable v4.14:
("net/mlx5: Check for error in mlx5_attach_interface")

For -stable v4.15:
("net/mlx5: Fix not releasing read lock when adding flow rules")

For -stable v4.17:
("net/mlx5: Fix possible deadlock from lockdep when adding fte to fg")

For -stable v4.18:
("net/mlx5: Use u16 for Work Queue buffer fragment size")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
net/iucv: fixes 2018-09-05

please apply three straight-forward fixes for iucv. One that prevents
leaking the skb on malformed inbound packets, one to fix the error
handling on transmit error, and one to get rid of a compile warning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes a compile warning.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sending an skb, afiucv_hs_send() bails out on various error
conditions. But currently the caller has no way of telling whether the
skb was freed or not - resulting in potentially either
a) leaked skbs from iucv_send_ctrl(), or
b) double-free's from iucv_sock_sendmsg().

As dev_queue_xmit() will always consume the skb (even on error), be
consistent and also free the skb from all other error paths. This way
callers no longer need to care about managing the skb.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inbound packets may have any combination of flag bits set in their iucv
header. If we don't know how to handle a specific combination, drop the
skb instead of leaking it.

To clarify what error is returned in this case, replace the hard-coded
0 with the corresponding macro.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If users try to install act_tunnel_key 'set' rules with duplicate values
of 'index', the tunnel metadata are allocated, but never released. Then,
kmemleak complains as follows:

 # tc a a a tunnel_key set src_ip 1.1.1.1 dst_ip 2.2.2.2 id 42 index 111
 # echo clear > /sys/kernel/debug/kmemleak
 # tc a a a tunnel_key set src_ip 1.1.1.1 dst_ip 2.2.2.2 id 42 index 111
 Error: TC IDR already exists.
 We have an error talking to the kernel
 # echo scan > /sys/kernel/debug/kmemleak
 # cat /sys/kernel/debug/kmemleak
 unreferenced object 0xffff8800574e6c80 (size 256):
   comm "tc", pid 5617, jiffies 4298118009 (age 57.990s)
   hex dump (first 32 bytes):
     00 00 00 00 00 00 00 00 00 1c e8 b0 ff ff ff ff  ................
     81 24 c2 ad ff ff ff ff 00 00 00 00 00 00 00 00  .$..............
   backtrace:
     [<00000000b7afbf4e>] tunnel_key_init+0x8a5/0x1800 [act_tunnel_key]
     [<000000007d98fccd>] tcf_action_init_1+0x698/0xac0
     [<0000000099b8f7cc>] tcf_action_init+0x15c/0x590
     [<00000000dc60eebe>] tc_ctl_action+0x336/0x5c2
     [<000000002f5a2f7d>] rtnetlink_rcv_msg+0x357/0x8e0
     [<000000000bfe7575>] netlink_rcv_skb+0x124/0x350
     [<00000000edab656f>] netlink_unicast+0x40f/0x5d0
     [<00000000b322cdcb>] netlink_sendmsg+0x6e8/0xba0
     [<0000000063d9d490>] sock_sendmsg+0xb3/0xf0
     [<00000000f0d3315a>] ___sys_sendmsg+0x654/0x960
     [<00000000c06cbd42>] __sys_sendmsg+0xd3/0x170
     [<00000000ce72e4b0>] do_syscall_64+0xa5/0x470
     [<000000005caa2d97>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
     [<00000000fac1b476>] 0xffffffffffffffff

This problem theoretically happens also in case users attempt to setup a
geneve rule having wrong configuration data, or when the kernel fails to
allocate 'params_new'. Ensure that tunnel_key_init() releases the tunnel
metadata also in the above conditions.

Addresses-Coverity-ID: 1373974 ("Resource leak")
Fixes: d0f6dd8a ("net/sched: Introduce act_tunnel_key")
Fixes: 0ed5269f ("net/sched: add tunnel option support to act_tunnel_key")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before we unlock the sock in tipc_release(), we have to
detach sk->sk_socket from sk, otherwise a parallel
tipc_sk_fill_sock_diag() could stil read it after we
free this socket.

Fixes: c30b70de ("tipc: implement socket diagnostics for AF_TIPC")
Reported-and-tested-by: syzbot+48804b87c16588ad491d@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a false positive report due to incorrect nested lock
annotations as we lock multiple fgs with the same subclass.
Instead of locking all fgs only lock the one being used as was
done before.

Fixes: bd71b08e ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Copy and paste bug was introduced in the offending patch.
We need to write udp source port value into the headers value and not
headers criteria "mask".

Fixes: 142644f8 ("net/mlx5e: Ethtool steering flow parsing refactoring")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)

Fixes: 737a234b ("net/mlx5: Introduce attach/detach to interface API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The PCI BDF is not unique. PCI domain must also be considered when
searching for the next physical device during lag setup. Example below:

mlx5_core 0000:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0000:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

If building match list fg fails and we never jumped to
search_again_locked label then the function returned without
unlocking the read lock.

Fixes: bd71b08e ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The memory allocated for the slow path table flow group input structure
was not freed upon successful return, fix that.

Fixes: 1967ce6e ("net/mlx5: E-Switch, Refactor fast path FDB table creation in switchdev mode")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.

u16 is sufficient to represent this.

Fixes: d7037ad7 ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.

u16 is sufficient to represent this.

Fixes: 388ca8be ("IB/mlx5: Implement fragmented completion queue (CQ)")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).

The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.

Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.

Fixes: 59211bd3 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.

Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.

So revert the optimization completely.

Fixes: 291ab06e ("net: qualcomm: new Ethernet over SPI driver for QCA700")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MC-aware mode was recently enabled by mlxsw on Spectrum switches in
commit 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw
ports"). Unfortunately, testing has shown that the fix is incomplete and
in the presented form actually makes the problem even worse, because any
amount of MC traffic causes UC disruption.

The reason for this is that currently, mlxsw configures the MC-specific
TCs (8..15) to map to pool 0. It also configures a maximum buffer size
of 0, but for MC traffic that maximum is disregarded and not part of the
quota. Therefore MC traffic is always admitted to the egress buffer.

Fix the configuration by directing the MC TCs into pool 15, which is
dedicated to MC traffic and recognized as such by the silicon.

Fixes: 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Must perform TXQ teardown before unregistering interfaces in
    mac80211, from Toke Høiland-Jørgensen.

 2) Don't allow creating mac80211_hwsim with less than one channel, from
    Johannes Berg.

 3) Division by zero in cfg80211, fix from Johannes Berg.

 4) Fix endian issue in tipc, from Haiqing Bai.

 5) BPF sockmap use-after-free fixes from Daniel Borkmann.

 6) Spectre-v1 in mac80211_hwsim, from Jinbum Park.

 7) Missing rhashtable_walk_exit() in tipc, from Cong Wang.

 8) Revert kvzalloc() conversion of AF_PACKET, it breaks mmap() when
    kvzalloc() tries to use kmalloc() pages. From Eric Dumazet.

 9) Fix deadlock in hv_netvsc, from Dexuan Cui.

10) Do not restart timewait timer on RST, from Florian Westphal.

11) Fix double lwstate refcount grab in ipv6, from Alexey Kodanev.

12) Unsolicit report count handling is off-by-one, fix from Hangbin Liu.

13) Sleep-in-atomic in cadence driver, from Jia-Ju Bai.

14) Respect ttl-inherit in ip6 tunnel driver, from Hangbin Liu.

15) Use-after-free in act_ife, fix from Cong Wang.

16) Missing hold to meta module in act_ife, from Vlad Buslov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
  net: phy: sfp: Handle unimplemented hwmon limits and alarms
  net: sched: action_ife: take reference to meta module
  act_ife: fix a potential use-after-free
  net/mlx5: Fix SQ offset in QPs with small RQ
  tipc: correct spelling errors for tipc_topsrv_queue_evt() comments
  tipc: correct spelling errors for struct tipc_bc_base's comment
  bnxt_en: Do not adjust max_cp_rings by the ones used by RDMA.
  bnxt_en: Clean up unused functions.
  bnxt_en: Fix firmware signaled resource change logic in open.
  sctp: not traverse asoc trans list if non-ipv6 trans exists for ipv6_flowlabel
  sctp: fix invalid reference to the index variable of the iterator
  net/ibm/emac: wrong emac_calc_base call was used by typo
  net: sched: null actions array pointer before releasing action
  vhost: fix VHOST_GET_BACKEND_FEATURES ioctl request definition
  r8169: add support for NCube 8168 network card
  ip6_tunnel: respect ttl inherit for ip6tnl
  mac80211: shorten the IBSS debug messages
  mac80211: don't Tx a deauth frame if the AP forbade Tx
  mac80211: Fix station bandwidth setting after channel switch
  mac80211: fix a race between restart and CSA flows
  ...

Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.

Fixes: 1323061a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent refactoring of add_metainfo() caused use_all_metadata() to add
metainfo to ife action metalist without taking reference to module. This
causes warning in module_put called from ife action cleanup function.

Implement add_metainfo_and_get_ops() function that returns with reference
to module taken if metainfo was added successfully, and call it from
use_all_metadata(), instead of calling __add_metainfo() directly.

Example warning:

[  646.344393] WARNING: CPU: 1 PID: 2278 at kernel/module.c:1139 module_put+0x1cb/0x230
[  646.352437] Modules linked in: act_meta_skbtcindex act_meta_mark act_meta_skbprio act_ife ife veth nfsv3 nfs fscache xt_CHECKSUM iptable_mangle ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c tun ebtable_filter ebtables ip6table_filter ip6_tables bridge stp llc mlx5_ib ib_uverbs ib_core intel_rapl sb_edac x86_pkg_temp_thermal mlx5_core coretemp kvm_intel kvm nfsd igb irqbypass crct10dif_pclmul devlink crc32_pclmul mei_me joydev ses crc32c_intel enclosure auth_rpcgss i2c_algo_bit ioatdma ptp mei pps_core ghash_clmulni_intel iTCO_wdt iTCO_vendor_support pcspkr dca ipmi_ssif lpc_ich target_core_mod i2c_i801 ipmi_si ipmi_devintf pcc_cpufreq wmi ipmi_msghandler nfs_acl lockd acpi_pad acpi_power_meter grace sunrpc mpt3sas raid_class scsi_transport_sas
[  646.425631] CPU: 1 PID: 2278 Comm: tc Not tainted 4.19.0-rc1+ #799
[  646.432187] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[  646.440595] RIP: 0010:module_put+0x1cb/0x230
[  646.445238] Code: f3 66 94 02 e8 26 ff fa ff 85 c0 74 11 0f b6 1d 51 30 94 02 80 fb 01 77 60 83 e3 01 74 13 65 ff 0d 3a 83 db 73 e9 2b ff ff ff <0f> 0b e9 00 ff ff ff e8 59 01 fb ff 85 c0 75 e4 48 c7 c2 20 62 6b
[  646.464997] RSP: 0018:ffff880354d37068 EFLAGS: 00010286
[  646.470599] RAX: 0000000000000000 RBX: ffffffffc0a52518 RCX: ffffffff8c2668db
[  646.478118] RDX: 0000000000000003 RSI: dffffc0000000000 RDI: ffffffffc0a52518
[  646.485641] RBP: ffffffffc0a52180 R08: fffffbfff814a4a4 R09: fffffbfff814a4a3
[  646.493164] R10: ffffffffc0a5251b R11: fffffbfff814a4a4 R12: 1ffff1006a9a6e0d
[  646.500687] R13: 00000000ffffffff R14: ffff880362bab890 R15: dead000000000100
[  646.508213] FS:  00007f4164c99800(0000) GS:ffff88036fe40000(0000) knlGS:0000000000000000
[  646.516961] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  646.523080] CR2: 00007f41638b8420 CR3: 0000000351df0004 CR4: 00000000001606e0
[  646.530595] Call Trace:
[  646.533408]  ? find_symbol_in_section+0x260/0x260
[  646.538509]  tcf_ife_cleanup+0x11b/0x200 [act_ife]
[  646.543695]  tcf_action_cleanup+0x29/0xa0
[  646.548078]  __tcf_action_put+0x5a/0xb0
[  646.552289]  ? nla_put+0x65/0xe0
[  646.555889]  __tcf_idr_release+0x48/0x60
[  646.560187]  tcf_generic_walker+0x448/0x6b0
[  646.564764]  ? tcf_action_dump_1+0x450/0x450
[  646.569411]  ? __lock_is_held+0x84/0x110
[  646.573720]  ? tcf_ife_walker+0x10c/0x20f [act_ife]
[  646.578982]  tca_action_gd+0x972/0xc40
[  646.583129]  ? tca_get_fill.constprop.17+0x250/0x250
[  646.588471]  ? mark_lock+0xcf/0x980
[  646.592324]  ? check_chain_key+0x140/0x1f0
[  646.596832]  ? debug_show_all_locks+0x240/0x240
[  646.601839]  ? memset+0x1f/0x40
[  646.605350]  ? nla_parse+0xca/0x1a0
[  646.609217]  tc_ctl_action+0x215/0x230
[  646.613339]  ? tcf_action_add+0x220/0x220
[  646.617748]  rtnetlink_rcv_msg+0x56a/0x6d0
[  646.622227]  ? rtnl_fdb_del+0x3f0/0x3f0
[  646.626466]  netlink_rcv_skb+0x18d/0x200
[  646.630752]  ? rtnl_fdb_del+0x3f0/0x3f0
[  646.634959]  ? netlink_ack+0x500/0x500
[  646.639106]  netlink_unicast+0x2d0/0x370
[  646.643409]  ? netlink_attachskb+0x340/0x340
[  646.648050]  ? _copy_from_iter_full+0xe9/0x3e0
[  646.652870]  ? import_iovec+0x11e/0x1c0
[  646.657083]  netlink_sendmsg+0x3b9/0x6a0
[  646.661388]  ? netlink_unicast+0x370/0x370
[  646.665877]  ? netlink_unicast+0x370/0x370
[  646.670351]  sock_sendmsg+0x6b/0x80
[  646.674212]  ___sys_sendmsg+0x4a1/0x520
[  646.678443]  ? copy_msghdr_from_user+0x210/0x210
[  646.683463]  ? lock_downgrade+0x320/0x320
[  646.687849]  ? debug_show_all_locks+0x240/0x240
[  646.692760]  ? do_raw_spin_unlock+0xa2/0x130
[  646.697418]  ? _raw_spin_unlock+0x24/0x30
[  646.701798]  ? __handle_mm_fault+0x1819/0x1c10
[  646.706619]  ? __pmd_alloc+0x320/0x320
[  646.710738]  ? debug_show_all_locks+0x240/0x240
[  646.715649]  ? restore_nameidata+0x7b/0xa0
[  646.720117]  ? check_chain_key+0x140/0x1f0
[  646.724590]  ? check_chain_key+0x140/0x1f0
[  646.729070]  ? __fget_light+0xbc/0xd0
[  646.733121]  ? __sys_sendmsg+0xd7/0x150
[  646.737329]  __sys_sendmsg+0xd7/0x150
[  646.741359]  ? __ia32_sys_shutdown+0x30/0x30
[  646.746003]  ? up_read+0x53/0x90
[  646.749601]  ? __do_page_fault+0x484/0x780
[  646.754105]  ? do_syscall_64+0x1e/0x2c0
[  646.758320]  do_syscall_64+0x72/0x2c0
[  646.762353]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  646.767776] RIP: 0033:0x7f4163872150
[  646.771713] Code: 8b 15 3c 7d 2b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb cd 66 0f 1f 44 00 00 83 3d b9 d5 2b 00 00 75 10 b8 2e 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 be cd 00 00 48 89 04 24
[  646.791474] RSP: 002b:00007ffdef7d6b58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  646.799721] RAX: ffffffffffffffda RBX: 0000000000000024 RCX: 00007f4163872150
[  646.807240] RDX: 0000000000000000 RSI: 00007ffdef7d6bd0 RDI: 0000000000000003
[  646.814760] RBP: 000000005b8b9482 R08: 0000000000000001 R09: 0000000000000000
[  646.822286] R10: 00000000000005e7 R11: 0000000000000246 R12: 00007ffdef7dad20
[  646.829807] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000679bc0
[  646.837360] irq event stamp: 6083
[  646.841043] hardirqs last  enabled at (6081): [<ffffffff8c220a7d>] __call_rcu+0x17d/0x500
[  646.849882] hardirqs last disabled at (6083): [<ffffffff8c004f06>] trace_hardirqs_off_thunk+0x1a/0x1c
[  646.859775] softirqs last  enabled at (5968): [<ffffffff8d4004a1>] __do_softirq+0x4a1/0x6ee
[  646.868784] softirqs last disabled at (6082): [<ffffffffc0a78759>] tcf_ife_cleanup+0x39/0x200 [act_ife]
[  646.878845] ---[ end trace b1b8c12ffe51e657 ]---

Fixes: 5ffe57da ("act_ife: fix a potential deadlock")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Immediately after module_put(), user could delete this
module, so e->ops could be already freed before we call
e->ops->release().

Fix this by moving module_put() after ops->release().

Fixes: ef6980b6 ("introduce IFE action")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct the formula for calculating the RQ page remainder,
which should be in byte granularity.  The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.

Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.

Fixes: d7037ad7 ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Here are quite a large number of fixes, notably:
 * various A-MSDU building fixes (currently only affects mt76)
 * syzkaller & spectre fixes in hwsim
 * TXQ vs. teardown fix that was causing crashes
 * embed WMM info in reg rule, bad code here had been causing crashes
 * one compilation issue with fix from Arnd (rfkill-gpio includes)
 * fixes for a race and bad data during/after channel switch
 * nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_conn_queue_evt -> tipc_topsrv_queue_evt
tipc_send_work -> tipc_conn_send_work
tipc_send_to_sock -> tipc_conn_send_to_sock
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix for two spelling mistakes.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes.

This short series fixes resource related logic in the driver, mostly
affecting the RDMA driver under corner cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA.  There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA.  This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.

To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.

Fixes: ec86f14e ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused bnxt_subtract_ulp_resources().  Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0.  This will properly setup the
init sequence to initialize the default rings again.  We also need
to signal the RDMA driver to stop and clear its interrupts.  We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.

Fixes: 25e1acd6 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: two fixes for spp_ipv6_flowlabel and spp_dscp sockopts

This patchset fixes two problems in sctp_apply_peer_addr_params()
when setting spp_ipv6_flowlabel or spp_dscp.
====================
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>