- 02 Oct, 2018 17 commits
-
-
Anssi Hannula authored
BugLink: https://bugs.launchpad.net/bugs/1791942 commit 32852c56 upstream. If the device gets into a state where RXNEMP (RX FIFO not empty) interrupt is asserted without RXOK (new frame received successfully) interrupt being asserted, xcan_rx_poll() will continue to try to clear RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is not empty, the interrupt will not be cleared and napi_schedule() will just be called again. This situation can occur when: (a) xcan_rx() returns without reading RX FIFO due to an error condition. The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear due to a frame still being in the FIFO. The frame will never be read from the FIFO as RXOK is no longer set. (b) A frame is received between xcan_rx_poll() reading interrupt status and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain set as the new message is still in the FIFO. I'm able to trigger case (b) by flooding the bus with frames under load. There does not seem to be any benefit in using both RXNEMP and RXOK in the way the driver does, and the polling example in the reference manual (UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either RXOK or RXNEMP can be used for detecting incoming messages. Fix the issue and simplify the RX processing by only using RXNEMP without RXOK. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44 ("can: xilinx CAN controller support") Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Cc: <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com>
-
Rafael J. Wysocki authored
BugLink: https://bugs.launchpad.net/bugs/1791942 commit 722e5f2b upstream. Commit 52cdbdd4 (driver core: correct device's shutdown order) introduced a regression by breaking device shutdown on some systems. Namely, the devices_kset_move_last() call in really_probe() added by that commit is a mistake as it may cause parents to follow children in the devices_kset list which then causes shutdown to fail. For example, if a device has children before really_probe() is called for it (which is not uncommon), that call will cause it to be reordered after the children in the devices_kset list and the ordering of that list will not reflect the correct device shutdown order any more. Also it causes the devices_kset list to be constantly reordered until all drivers have been probed which is totally pointless overhead in the majority of cases and it only covered an issue with system shutdown, while system-wide suspend/resume potentially had the same issue on the affected platforms (which was not covered). Moreover, the shutdown issue originally addressed by the change in really_probe() made by commit 52cdbdd4 is not present in 4.18-rc any more, since dra7 started to use the sdhci-omap driver which doesn't disable any regulators during shutdown, so the really_probe() part of commit 52cdbdd4 can be safely reverted. [The original issue was related to the omap_hsmmc driver used by dra7 previously.] For the above reasons, revert the really_probe() modifications made by commit 52cdbdd4. The other code changes made by commit 52cdbdd4 are useful and they need not be reverted. Fixes: 52cdbdd4 (driver core: correct device's shutdown order) Link: https://lore.kernel.org/lkml/CAFgQCTt7VfqM=UyCnvNFxrSw8Z6cUtAi3HUwR4_xPAc03SgHjQ@mail.gmail.com/Reported-by:
Pingfan Liu <kernelfans@gmail.com> Tested-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Jerry Zhang authored
BugLink: https://bugs.launchpad.net/bugs/1791942 commit 4d644abf upstream. Commit 1b9ba000 ("Allow function drivers to pause control transfers") states that USB_GADGET_DELAYED_STATUS is only supported if data phase is 0 bytes. It seems that when the length is not 0 bytes, there is no need to explicitly delay the data stage since the transfer is not completed until the user responds. However, when the length is 0, there is no data stage and the transfer is finished once setup() returns, hence there is a need to explicitly delay completion. This manifests as the following bugs: Prior to 946ef68a ('Let setup() return USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs would require user to queue a 0 byte request in order to clear setup state. However, that 0 byte request was actually not needed and would hang and cause errors in other setup requests. After the above commit, 0 byte setups work since the gadget now accepts empty queues to ep0 to clear the delay, but all other setups hang. Fixes: 946ef68a ("Let setup() return USB_GADGET_DELAYED_STATUS") Signed-off-by:
Jerry Zhang <zhangjerry@google.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Bin Liu authored
BugLink: https://bugs.launchpad.net/bugs/1791942 commit 249a32b7 upstream. Based on USB2.0 Spec Section 11.12.5, "If a hub has per-port power switching and per-port current limiting, an over-current on one port may still cause the power on another port to fall below specific minimums. In this case, the affected port is placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the port, but PORT_OVER_CURRENT is not set." so let's check C_PORT_OVER_CURRENT too for over current condition. Fixes: 08d1dec6 ("usb:hub set hub->change_bits when over-current happens") Cc: <stable@vger.kernel.org> Tested-by:
Alessandro Antenucci <antenucci@korg.it> Signed-off-by:
Bin Liu <b-liu@ti.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Lubomir Rintel authored
BugLink: https://bugs.launchpad.net/bugs/1791942 commit 1445cbe4 upstream. The device (a POS terminal) implements CDC ACM, but has not union descriptor. Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Acked-by:
Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Willem de Bruijn authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit 2efd4fca ] Syzbot reported a read beyond the end of the skb head when returning IPV6_ORIGDSTADDR: BUG: KMSAN: kernel-infoleak in put_cmsg+0x5ef/0x860 net/core/scm.c:242 CPU: 0 PID: 4501 Comm: syz-executor128 Not tainted 4.17.0+ #9 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:113 kmsan_report+0x188/0x2a0 mm/kmsan/kmsan.c:1125 kmsan_internal_check_memory+0x138/0x1f0 mm/kmsan/kmsan.c:1219 kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1261 copy_to_user include/linux/uaccess.h:184 [inline] put_cmsg+0x5ef/0x860 net/core/scm.c:242 ip6_datagram_recv_specific_ctl+0x1cf3/0x1eb0 net/ipv6/datagram.c:719 ip6_datagram_recv_ctl+0x41c/0x450 net/ipv6/datagram.c:733 rawv6_recvmsg+0x10fb/0x1460 net/ipv6/raw.c:521 [..] This logic and its ipv4 counterpart read the destination port from the packet at skb_transport_offset(skb) + 4. With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a packet that stores headers exactly up to skb_transport_offset(skb) in the head and the remainder in a frag. Call pskb_may_pull before accessing the pointer to ensure that it lies in skb head. Link: http://lkml.kernel.org/r/CAF=yD-LEJwZj5a1-bAAj2Oy_hKmGygV6rsJ_WOrAYnv-fnayiQ@mail.gmail.com Reported-by: syzbot+9adb4b567003cac781f0@syzkaller.appspotmail.com Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Yuchung Cheng authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit a0496ef2 ] Per DCTCP RFC8257 (Section 3.2) the ACK reflecting the CE status change has to be sent immediately so the sender can respond quickly: """ When receiving packets, the CE codepoint MUST be processed as follows: 1. If the CE codepoint is set and DCTCP.CE is false, set DCTCP.CE to true and send an immediate ACK. 2. If the CE codepoint is not set and DCTCP.CE is true, set DCTCP.CE to false and send an immediate ACK. """ Previously DCTCP implementation may continue to delay the ACK. This patch fixes that to implement the RFC by forcing an immediate ACK. Tested with this packetdrill script provided by Larry Brakmo 0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0 0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0 0.000 bind(3, ..., ...) = 0 0.000 listen(3, 1) = 0 0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7> 0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8> 0.110 < [ect0] . 1:1(0) ack 1 win 257 0.200 accept(3, ..., ...) = 4 +0 setsockopt(4, SOL_SOCKET, SO_DEBUG, [1], 4) = 0 0.200 < [ect0] . 1:1001(1000) ack 1 win 257 0.200 > [ect01] . 1:1(0) ack 1001 0.200 write(4, ..., 1) = 1 0.200 > [ect01] P. 1:2(1) ack 1001 0.200 < [ect0] . 1001:2001(1000) ack 2 win 257 +0.005 < [ce] . 2001:3001(1000) ack 2 win 257 +0.000 > [ect01] . 2:2(0) ack 2001 // Previously the ACK below would be delayed by 40ms +0.000 > [ect01] E. 2:2(0) ack 3001 +0.500 < F. 9501:9501(0) ack 4 win 257 Signed-off-by:
Yuchung Cheng <ycheng@google.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Yuchung Cheng authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit 27cde44a ] Currently when a DCTCP receiver delays an ACK and receive a data packet with a different CE mark from the previous one's, it sends two immediate ACKs acking previous and latest sequences respectly (for ECN accounting). Previously sending the first ACK may mark off the delayed ACK timer (tcp_event_ack_sent). This may subsequently prevent sending the second ACK to acknowledge the latest sequence (tcp_ack_snd_check). The culprit is that tcp_send_ack() assumes it always acknowleges the latest sequence, which is not true for the first special ACK. The fix is to not make the assumption in tcp_send_ack and check the actual ack sequence before cancelling the delayed ACK. Further it's safer to pass the ack sequence number as a local variable into tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid future bugs like this. Reported-by:
-
Yuchung Cheng authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit 2987babb ] Refactor and create helpers to send the special ACK in DCTCP. Signed-off-by:
-
Yuchung Cheng authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit b0c05d0e ] Previously, when a data segment was sent an ACK was piggybacked on the data segment without generating a CA_EVENT_NON_DELAYED_ACK event to notify congestion control modules. So the DCTCP ca->delayed_ack_reserved flag could incorrectly stay set when in fact there were no delayed ACKs being reserved. This could result in sending a special ECN notification ACK that carries an older ACK sequence, when in fact there was no need for such an ACK. DCTCP keeps track of the delayed ACK status with its own separate state ca->delayed_ack_reserved. Previously it may accidentally cancel the delayed ACK without updating this field upon sending a special ACK that carries a older ACK sequence. This inconsistency would lead to DCTCP receiver never acknowledging the latest data until the sender times out and retry in some cases. Packetdrill script (provided by Larry Brakmo) 0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0 0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0 0.000 bind(3, ..., ...) = 0 0.000 listen(3, 1) = 0 0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7> 0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8> 0.110 < [ect0] . 1:1(0) ack 1 win 257 0.200 accept(3, ..., ...) = 4 0.200 < [ect0] . 1:1001(1000) ack 1 win 257 0.200 > [ect01] . 1:1(0) ack 1001 0.200 write(4, ..., 1) = 1 0.200 > [ect01] P. 1:2(1) ack 1001 0.200 < [ect0] . 1001:2001(1000) ack 2 win 257 0.200 write(4, ..., 1) = 1 0.200 > [ect01] P. 2:3(1) ack 2001 0.200 < [ect0] . 2001:3001(1000) ack 3 win 257 0.200 < [ect0] . 3001:4001(1000) ack 3 win 257 0.200 > [ect01] . 3:3(0) ack 4001 0.210 < [ce] P. 4001:4501(500) ack 3 win 257 +0.001 read(4, ..., 4500) = 4500 +0 write(4, ..., 1) = 1 +0 > [ect01] PE. 3:4(1) ack 4501 +0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257 // Previously the ACK sequence below would be 4501, causing a long RTO +0.040~+0.045 > [ect01] . 4:4(0) ack 5501 // delayed ack +0.311 < [ect0] . 5501:6501(1000) ack 4 win 257 // More data +0 > [ect01] . 4:4(0) ack 6501 // now acks everything +0.500 < F. 9501:9501(0) ack 4 win 257 Reported-by:
Larry Brakmo <brakmo@fb.com> Signed-off-by:
-
Roopa Prabhu authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit 5025f7f7 ] rtnl_configure_link sets dev->rtnl_link_state to RTNL_LINK_INITIALIZED and unconditionally calls __dev_notify_flags to notify user-space of dev flags. current call sequence for rtnl_configure_link rtnetlink_newlink rtnl_link_ops->newlink rtnl_configure_link (unconditionally notifies userspace of default and new dev flags) If a newlink handler wants to call rtnl_configure_link early, we will end up with duplicate notifications to user-space. This patch fixes rtnl_configure_link to check rtnl_link_state and call __dev_notify_flags with gchanges = 0 if already RTNL_LINK_INITIALIZED. Later in the series, this patch will help the following sequence where a driver implementing newlink can call rtnl_configure_link to initialize the link early. makes the following call sequence work: rtnetlink_newlink rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes link and notifies user-space of default dev flags) rtnl_configure_link (updates dev flags if requested by user ifm and notifies user-space of new dev flags) Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
Jack Morgenstein authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit 958c696f ] Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp context, rather than the one passed in the input modifier. However, the qp number in the qp context is not defined as a required parameter by the FW. Therefore, drivers may choose to not specify the qp number in the qp context for the reset-to-init transition. Thus, we must save the qp number passed in the command input modifier -- which is always present. (This saved qp number is used as the input modifier for command 2RST_QP when a slave's qp's are destroyed). Fixes: c82e9aa0 ("mlx4_core: resource tracking for HCA resources used by guests") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Paolo Abeni authored
BugLink: https://bugs.launchpad.net/bugs/1791942 [ Upstream commit 3dd1c9a1 ] The skb hash for locally generated ip[v6] fragments belonging to the same datagram can vary in several circumstances: * for connected UDP[v6] sockets, the first fragment get its hash via set_owner_w()/skb_set_hash_from_sk() * for unconnected IPv6 UDPv6 sockets, the first fragment can get its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if auto_flowlabel is enabled For the following frags the hash is usually computed via skb_get_hash(). The above can cause OoO for unconnected IPv6 UDPv6 socket: in that scenario the egress tx queue can be selected on a per packet basis via the skb hash. It may also fool flow-oriented schedulers to place fragments belonging to the same datagram in different flows. Fix the issue by copying the skb hash from the head frag into the others at fragmentation time. Before this commit: perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8" netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n & perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1 perf script probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0 probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0 After this commit: probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0 probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0 Fixes: b73c3d0e ("net: Save TX flow hash in sock and set in skbuf on xmit") Fixes: 67800f9b ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Felix Fietkau authored
BugLink: https://bugs.launchpad.net/bugs/1791942 commit bc88ad2e upstream. ath79_ddr_wb_flush_base has the type void __iomem *, so register offsets need to be a multiple of 4 in order to access the intended register. Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
John Crispin <john@phrozen.org> Signed-off-by:
Paul Burton <paul.burton@mips.com> Fixes: 24b0e3e8 ("MIPS: ath79: Improve the DDR controller interface") Patchwork: https://patchwork.linux-mips.org/patch/19912/ Cc: Alban Bedel <albeu@free.fr> Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org # 4.2+ Signed-off-by:
-
Ross Lagerwall authored
BugLink: https://bugs.launchpad.net/bugs/1793753 Fix a race between ip_set_dump_start() and ip_set_swap(). The race is as follows: * Without holding the ref lock, ip_set_swap() checks ref_netlink of the set and it is 0. * ip_set_dump_start() takes a reference on the set. * ip_set_swap() does the swap (even though it now has a non-zero reference count). * ip_set_dump_start() gets the set from ip_set_list again which is now a different set since it has been swapped. * ip_set_dump_start() calls __ip_set_put_netlink() and hits a BUG_ON due to the reference count being 0. Fix this race by extending the critical region in which the ref lock is held to include checking the ref counts. The race can be reproduced with the following script: while :; do ipset destroy hash_ip1 ipset destroy hash_ip2 ipset create hash_ip1 hash:ip family inet hashsize 1024 \ maxelem 500000 ipset create hash_ip2 hash:ip family inet hashsize 300000 \ maxelem 500000 ipset create hash_ip3 hash:ip family inet hashsize 1024 \ maxelem 500000 ipset save & ipset swap hash_ip3 hash_ip2 ipset destroy hash_ip3 wait done Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by:
Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> (cherry picked from commit e5173418) Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
Vishwanath Pai authored
BugLink: https://bugs.launchpad.net/bugs/1793753 This fix adds a new reference counter (ref_netlink) for the struct ip_set. The other reference counter (ref) can be swapped out by ip_set_swap and we need a separate counter to keep track of references for netlink events like dump. Using the same ref counter for dump causes a race condition which can be demonstrated by the following script: ipset create hash_ip1 hash:ip family inet hashsize 1024 maxelem 500000 \ counters ipset create hash_ip2 hash:ip family inet hashsize 300000 maxelem 500000 \ counters ipset create hash_ip3 hash:ip family inet hashsize 1024 maxelem 500000 \ counters ipset save & ipset swap hash_ip3 hash_ip2 ipset destroy hash_ip3 /* will crash the machine */ Swap will exchange the values of ref so destroy will see ref = 0 instead of ref = 1. With this fix in place swap will not succeed because ipset save still has ref_netlink on the set (ip_set_swap doesn't swap ref_netlink). Both delete and swap will error out if ref_netlink != 0 on the set. Note: The changes to *_head functions is because previously we would increment ref whenever we called these functions, we don't do that anymore. Reviewed-by:
Joshua Hunt <johunt@akamai.com> Signed-off-by:
Vishwanath Pai <vpai@akamai.com> Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
When we are checking for the existence of ABI files, we will use the previous changelog stanza version as part of the lookup path. On backport kernels where we just copy the master kernel ABI, that ABI path will not have the same version as the backport kernel. We didn't catch this before because we didn't call the insertchanges rule for backports, which would call final-checks, and also because we changed the changelog to use the version from the master kernel. As we plan to change those two factors, we will start seeing check failures that we shouldn't. Ignore: yes Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by:
Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Signed-off-by:
-
- 28 Sep, 2018 23 commits
-
-
Marcelo Henrique Cerri authored
BugLink: http://bugs.launchpad.net/bugs/1793461 Update the startnewrelease target to support backport version numbers when creating the new changelog entry. Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 Added memory barriers where they were missing to support multiple architectures, and removed redundant ones. As part of removing the redundant memory barriers and improving performance, we moved to more relaxed versions of memory barriers, as well as to the more relaxed version of writel - writel_relaxed, while maintaining correctness. Signed-off-by:
Netanel Belgazal <netanel@amazon.com> Signed-off-by:
Brad Figg <brad.figg@canonical.com> Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 Add READ_ONCE calls where necessary (for example when iterating over a memory field that gets updated by the hardware). Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 acquire the rtnl_lock during device destruction to avoid using partially destroyed device. ena_remove() shares almost the same logic as ena_destroy_device(), so use ena_destroy_device() and avoid duplications. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 ena_destroy_device() can potentially be called twice. To avoid this, check that the device is running and only then proceed destroying it. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 When ena_destroy_device() is called from ena_suspend(), the device is still reachable from the driver. Therefore, the driver can send a command to the device to free all resources. However, in all other cases of calling ena_destroy_device(), the device is potentially in an error state and unreachable from the driver. In these cases the driver must not send commands to the device. The current implementation does not request resource freeing from the device even when possible. We add the graceful parameter to ena_destroy_device() to enable resource freeing when possible, and use it in ena_suspend(). Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 The buffer length field in the ena rx descriptor is 16 bit, and the current driver passes a full page in each ena rx descriptor. When PAGE_SIZE equals 64kB or more, the buffer length field becomes zero. To solve this issue, limit the ena Rx descriptor to use 16kB even when allocating 64kB kernel pages. This change would not impact ena device functionality, as 16kB is still larger than maximum MTU. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 Starting with driver version 1.5.0, in case of a surprise device unplug, there is a race caused by invoking ena_destroy_device() from two different places. As a result, the readless register might be accessed after it was destroyed. Signed-off-by:
-
Gal Pressman authored
BugLink: http://bugs.launchpad.net/bugs/1792044 UBSAN triggers the following undefined behaviour warnings: [...] [ 13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22 [ 13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int' [...] [ 13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4 [ 13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int' [...] When splitting the address to high and low, GENMASK_ULL is used to generate a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and ena_com_add_single_rx_desc). The problem is that dma_addr_bits is not initialized with a proper value (besides being cleared in ena_com_create_io_queue). Assign dma_addr_bits the correct value that is stored in ena_dev when initializing the SQ. Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by:
Gal Pressman <pressmangal@gmail.com> Signed-off-by:
-
Kees Cook authored
BugLink: http://bugs.launchpad.net/bugs/1792044 As implemented in upstream commit a86854d0 "treewide: devm_kzalloc() -> devm_kcalloc()", for ena only. (backported from commit a86854d0) Signed-off-by:
-
Sinan Kaya authored
BugLink: http://bugs.launchpad.net/bugs/1792044 Code includes barrier() followed by writel(). writel() already has a barrier on some architectures like arm64. This ends up CPU observing two barriers back to back before executing the register write. Create a new wrapper function with relaxed write operator. Use the new wrapper when a write is following a barrier(). Since code already has an explicit barrier call, changing writel() to writel_relaxed() and adding mmiowb() for ordering protection. Signed-off-by:
Sinan Kaya <okaya@codeaurora.org> Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 ENA admin command queue errors are not handled as part of ena_down(). As a result, in case of error admin queue transitions to non-running state and aborts all subsequent commands including those coming from ena_up(). Reset scheduled by the driver from the timer service context would not proceed due to sharing rtnl with ena_up()/ena_down() Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 A mechanism for detection of stuck Rx/Tx rings due to missed or misrouted interrupts. Check if there are unhandled completion descriptors before the first MSI-X interrupt arrived. The check is per queue and per interrupt vector. Once such condition is detected, driver and device reset is scheduled. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 In rare cases, ena driver would reset and re-start the device, for example, in case of misbehaving application that causes transmit timeout The first step in the reset procedure is to stop the Tx traffic by calling ena_carrier_off(). After the driver have just started the device reset procedure, device happens to send an asynchronous notification (via AENQ) to the driver than there was a link change (to link-up state). This link change is mapped to a call to netif_carrier_on() which re-activates the Tx queues, violating the assumption of no tx traffic until device reset is completed, as the reset task might still be in the process of queues initialization, leading to an access to uninitialized memory. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 Add a new statistic to ethtool stats that show the number of packets without transmit acknowledgement from ENA device. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 Remove ena_device_io_suspend/resume() methods Those methods were intend to be used by the device to trigger suspend/resume but eventually it was dropped. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 The ena admin commands timeout is in resolutions of 100ms. Therefore, When the driver works in polling mode, it sleeps for 100ms each time. The overall boot time of the ENA driver is ~1.5 sec. To reduce the boot time, This change modifies the granularity of the sleeps to 5ms. This change improves the boot time to 220ms. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 ethtool ena_get_channels() expose the max number of queues as the max number of queues ENA supports (128 queues) and not the actual number of created queues. Signed-off-by:
-
Netanel Belgazal authored
BugLink: http://bugs.launchpad.net/bugs/1792044 This failure is rare and only found on testing where deliberately fail devm_ioremap() [ 451.170464] ena 0000:04:00.0: failed to remap regs bar 451.170549] Workqueue: pciehp-1 pciehp_power_thread [ 451.170551] task: ffff88085a5f2d00 task.stack: ffffc9000756c000 [ 451.170552] RIP: 0010:devm_iounmap+0x2d/0x40 [ 451.170553] RSP: 0018:ffffc9000756fac0 EFLAGS: 00010282 [ 451.170554] RAX: 00000000fffffffe RBX: 0000000000000000 RCX: 0000000000000000 [ 451.170555] RDX: ffffffff813a7e00 RSI: 0000000000000282 RDI: 0000000000000282 [ 451.170556] RBP: ffffc9000756fac8 R08: 00000000fffffffe R09: 00000000000009b7 [ 451.170557] R10: 0000000000000005 R11: 00000000000009b6 R12: ffff880856c9d0a0 [ 451.170558] R13: ffffc9000f5c90c0 R14: ffff880856c9d0a0 R15: 0000000000000028 [ 451.170559] FS: 0000000000000000(0000) GS:ffff88085f400000(0000) knlGS:0000000000000000 [ 451.170560] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 451.170561] CR2: 00007f169038b000 CR3: 0000000001c09000 CR4: 00000000003406f0 [ 451.170562] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 451.170562] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 451.170563] Call Trace: [ 451.170572] ena_release_bars.isra.48+0x34/0x60 [ena] [ 451.170574] ena_probe+0x144/0xd90 [ena] [ 451.170579] ? ida_simple_get+0x98/0x100 [ 451.170585] ? kernfs_next_descendant_post+0x40/0x50 [ 451.170591] local_pci_probe+0x45/0xa0 [ 451.170592] pci_device_probe+0x157/0x180 [ 451.170599] driver_probe_device+0x2a8/0x460 [ 451.170600] __device_attach_driver+0x7e/0xe0 [ 451.170602] ? driver_allows_async_probing+0x30/0x30 [ 451.170603] bus_for_each_drv+0x68/0xb0 [ 451.170605] __device_attach+0xdd/0x160 [ 451.170607] device_attach+0x10/0x20 [ 451.170610] pci_bus_add_device+0x4f/0xa0 [ 451.170611] pci_bus_add_devices+0x39/0x70 [ 451.170613] pciehp_configure_device+0x96/0x120 [ 451.170614] pciehp_enable_slot+0x1b3/0x290 [ 451.170616] pciehp_power_thread+0x3b/0xb0 [ 451.170622] process_one_work+0x149/0x360 [ 451.170623] worker_thread+0x4d/0x3c0 [ 451.170626] kthread+0x109/0x140 [ 451.170627] ? rescuer_thread+0x380/0x380 [ 451.170628] ? kthread_park+0x60/0x60 [ 451.170632] ret_from_fork+0x25/0x30 Signed-off-by:
-
