- 10 Dec, 2013 40 commits
-
-
Kuninori Morimoto authored
Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
Interrupts generated by SoC internal devices are currently marked as IRQ_TYPE_NONE. As they're level-triggered and active-high, mark them as such. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Magnus Damm authored
The r8a7791 GPIO resources are currently incorrect. Fix that by making them match the English r8a7791 v0.31 data sheet. Tested with GPIO LED using Koelsch DT reference. Signed-off-by:
Magnus Damm <damm@opensource.se> Signed-off-by:
Simon Horman <horms@verge.net.au>
-
Magnus Damm authored
Add 2GiB of DRAM at 0x1_8000_0000 to support the full 4GiB of Lager system memory in case of DT Reference. Signed-off-by:
-
Magnus Damm authored
Add 2GiB of DRAM at 0x1_8000_0000 to support the full 4GiB of Lager system memory. Signed-off-by:
-
Takashi Yoshii authored
Add 1GiB of DRAM at 0x2_0000_0000 to support the full 2GiB of APE6EVM system memory. Signed-off-by:
Takashi Yoshii <takasi-y@ops.dti.ne.jp> Signed-off-by:
-
Magnus Damm authored
Add 1GiB of DRAM at 0x2_0000_0000 to support the full 2GiB of APE6EVM system memory also in case of DT reference. Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Magnus Damm authored
Add led6, led7 and led8 to the Koelsch DT reference board support. Signed-off-by:
-
Magnus Damm authored
Use the gpio-keys driver to support the 4 pins on the dip switch DSW2 which is mounted on the KZM9D board. Signed-off-by:
-
Laurent Pinchart authored
The device is configured to generate an active-low interrupt signal that needs to be acknowledged by the host. Configure the IRQ to trigger on low level. Signed-off-by:
-
Magnus Damm authored
Add "renesas,irqc-r8a7790" to the compatible string for IRQC in case of r8a7790. This makes the IRQC follow the same style as the other devices and also makes it more future proof. Signed-off-by:
-
Magnus Damm authored
Add "renesas,mmcif-r8a7790" to the compatible string for MMCIF in case of r8a7790. This makes the MMCIF follow the same style as the other devices and also makes it more future proof. Signed-off-by:
-
Magnus Damm authored
Hook up the r8a7791 thermal sensor to the DTS. Signed-off-by:
-
Magnus Damm authored
Hook up the r8a7790 thermal sensor to the DTS. Signed-off-by:
-
Magnus Damm authored
Configure the "D" set of data signals for SCIF0 and SCIF1 on the Koelsch board to setup pinctrl serial console bits. Signed-off-by:
-
Magnus Damm authored
Add "renesas,irqc-r8a7791" to the compatible string for IRQC in case of r8a7791. This makes the IRQC follow the same style as the other devices and also makes it more future proof. Signed-off-by:
-
Kuninori Morimoto authored
sh73a0 != r8a7740 Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Kuninori Morimoto authored
WP pin is not implemented on Marzen Acked-by:
-
Kuninori Morimoto authored
WP pin is not implemented on Marzen Acked-by:
-
Laurent Pinchart authored
The device is configured to generate an active-low interrupt signal that is automatically deasserted without requiring any action from the host. Configure the IRQ to trigger on falling edge. Signed-off-by:
-
Laurent Pinchart authored
The device is configured to generate an active-low interrupt signal that is automatically deasserted without requiring any action from the host. Configure the IRQ to trigger on falling edge. Signed-off-by:
-
Laurent Pinchart authored
The device is configured to generate an active-low interrupt signal that is automatically deasserted without requiring any action from the host. Use falling edge trigger as that is the configuration currently used on the board. Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Laurent Pinchart authored
In order to allow usage of the preprocessor in the SoC device tree sources, switch from /include/ to #include. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Takashi Yoshii authored
Add minimum clock tree description to .dts file. This provides same set of clocks as current sh-clkfwk version .c code does. Signed-off-by:
-
Kuninori Morimoto authored
According to ePAPR spec, this patch tidies up DT node name. Signed-off-by:
-
Kuninori Morimoto authored
According to ePAPR spec, this patch tidies up DT node name. Signed-off-by:
-
Kuninori Morimoto authored
According to ePAPR spec, this patch tidies up DT node name. Signed-off-by:
-
Kuninori Morimoto authored
According to ePAPR spec, this patch tidies up DT node name. Signed-off-by:
-
Kuninori Morimoto authored
According to ePAPR spec, this patch tidies up DT node name. Signed-off-by:
-
Kuninori Morimoto authored
According to ePAPR spec, this patch tidies up DT node name. This patch removed un-used "touchscreen" label Signed-off-by:
-
Kuninori Morimoto authored
According to ePAPR spec, this patch tidies up DT node name and related clock. Signed-off-by:
-
