- 02 Jul, 2022 30 commits
-
-
Chris Mi authored
Currently, there are three eswitch modes, none, legacy and switchdev. None is the default mode. Remove redundant none mode as eswitch mode should always be either legacy mode or switchdev mode. With this patch, there are two behavior changes: 1. Legacy becomes the default mode. When querying eswitch mode using devlink, a valid mode is always returned. 2. When disabling sriov, the eswitch mode will not change, only vfs are unloaded. Signed-off-by:
Chris Mi <cmi@nvidia.com> Reviewed-by:
Maor Dickman <maord@nvidia.com> Reviewed-by:
Roi Dayan <roid@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Chris Mi authored
Introduce flag to indicate if fdb table is created as a pre-step to prepare for removing dependency between sriov and eswitch mode in the downstream patches. Signed-off-by:
Mark Bloch <mbloch@nvidia.com> Reviewed-by:
-
Chris Mi authored
Eswitch vport acl namespace is needed when loading vfs. There is no need to free and reallocate it when switching eswitch mode. Introduce flag to indicate if it is created or not. When needed, create it. Only free it when the driver is unloaded or in bare metal mode. Signed-off-by:
-
Dan Carpenter authored
Smatch complains about this function: drivers/net/ethernet/mellanox/mlx5/core/eswitch.c:2000 mlx5_esw_unlock() warn: inconsistent returns '&esw->mode_lock'. Before commit ec2fa47d ("net/mlx5: Lag, use lag lock") there used to be a matching mlx5_esw_lock() function and the lock and unlock functions were symmetric. But now we take the lock unconditionally and must unlock unconditionally as well. As near as I can tell this is dead code and can just be deleted. Signed-off-by:Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Leon Romanovsky authored
ipsec_fs.h is not used and can be safely deleted. Signed-off-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
David S. Miller authored
Arun Ramadoss says: ==================== net: dsa: microchip: DSA Driver support for LAN937x LAN937x is a Multi-Port 100BASE-T1 Ethernet Physical Layer switch compliant with the IEEE 802.3bw-2015 specification. The device provides 100 Mbit/s transmit and receive capability over a single Unshielded Twisted Pair (UTP) cable. LAN937x is successive revision of KSZ series switch. This series of patches provide the DSA driver support for Microchip LAN937X switch through MII/RMII interface. The RGMII interface support will be added in the follow up series. LAN937x uses the most of functionality of KSZ9477. The LAN937x switch series family consists of following SKUs: LAN9370: - 4 T1 Phys - 1 RGMII port LAN9371: - 3 T1 Phys & 1 TX Phy - 2 RGMII ports LAN9372: - 5 T1 Phys & 1 TX Phy - 2 RGMII ports LAN9373: - 5 T1 Phys - 2 RGMII - 1 SGMII port LAN9374: - 6 T1 Phys - 2 RGMII ports Changes in v15: - fixed compilation issue. - Updated the phylink_mac_link_up to check only for 10/100/1000 speed. Changes in v14: - Updated the patch series to latest ksz code refactoring. - RGMII register configuration is removed from the series. It will be added in the follow up patch series. Changes in v13: - Fixed the compilation issue in patch 5 and 6 Changes in v12: - Removed the reduntant spi indirect enable in lan937x_init - Used the ksz_port_stp_state_set function - Apply rgmii internal delay only if it is rgmii port - Set the bit for 100baseTx in phylink_get_caps - Moved the ethtool related API from patch 5 to 7 - Moved lan_alu_entry struct in lan937x_dev.h from patch 5 to 9 - Moved lan_vlan_entry in lan937x_dev.h from patch 5 to 10 - Used the ksz_get_stats64 function for get_stats64 hook - Splitted the patch 5. one for port configuration, spi driver, phy read & write and mtu configuration. - Updated the indentation in ethernet-controller.yaml - lan937x.yaml: Removed the blank lines, updated the ethernet handle to macb0. Added the rgmii internal delay only for the ports. Changes in v11: - Tagged as RFC to get the feedback for the subpatches 1/10, 5/10 and 6/10 Changes in v10: - dsa.yaml: dropped moving mdio properties to dsa.yaml as per the feedback https://patchwork.kernel.org/project/netdevbpf/patch/20220318085540.281721-3-prasanna.vengateshan@microchip.com/#24787466 - microchip,lan937x.yaml: Naming convention changes in the example - lan937x_main.c: Moving configurations from lan937x_reset_switch() to setup() - lan937x_main.c: helper function has been introduced for lan937x_internal_phy_read & write - lan937x_dev.h: lan_alu_struct struct data type changes - lan937x_main.c: lan937x_get_stats64 make non blocking - lan937x_main.c: modified lan937x_port_mirror_add to include extack Changes in v9: - lan937x_main.c: of_node_put() correction in lan937x_parse_dt_rgmii_delay - lan937x_dev.c: removed the interface checks from lan937x_apply_rgmii_delay. - changes in ethernet-controller.yaml and dsa.yaml Changes in v8: - lan937x_dev.c: fixed lan937x_r_mib_pkt warning in the sub patches - lan937x_main.c: phylink_autoneg_inband() check removed in lan937x_phylink_mac_link_up() - lan937x_main.c: made legacy_pre_march2020 = false as this is non-legacy driver and indentation correction in lan937x_phylink_mac_link_up() - removed unnecessary parenthesis in lan937x_get_strings() Changes in v7: - microchip,lan937x.yaml: *-internal-delay-ps enum values & commit messages corrections - lan937x_main.c: removed phylink_validate() and added phylink_get_caps() - lan937x_main.c: added support for ethtool standard stats (get_eth_*_stats and get_stats64) - lan937x_main.c: removed unnecessary PVID read from lan937x_port_vlan_del() - integrated the changes of ksz9477 multi bridging support to lan937x dev and tested both multi bridging and STP - lan937x_port_vlan_del - dummy pvid read removed Changes in v6: - microchip_t1.c: There was new merge done in the net-next tree for microchip_1.c after the v5 submission. Hence rebased it for v6. Changes in v5: - microchip,lan937x.yaml: Added mdio properties detail - microchip,lan937x.yaml: *-internal-delay-ps added under port node - lan937x_dev.c: changed devm_mdiobus_alloc from of_mdiobus_register as suggested by Vladimir - lan937x_dev.c: added dev_info for rgmii internal delay & error message to user in case of out of range values - lan937x_dev.c: return -EOPNOTSUPP for C45 regnum values for lan937x_sw_mdio_read & write operations - return from function with out storing in a variable - lan937x_main.c: Added vlan_enable info in vlan_filtering API - lan937x_main.c: lan937x_port_vlan_del: removed unintended PVID write Changes in v4: - tag_ksz.c: cpu_to_be16 to put_unaligned_be16 - correct spacing in comments - tag_ksz.c: NETIF_F_HW_CSUM fix is integrated - lan937x_dev.c: mdio_np is removed from global and handled locally - lan937x_dev.c: unused functions removed lan937x_cfg32 & lan937x_port_cfg32 - lan937x_dev.c: lan937x_is_internal_100BTX_phy_port function name changes - lan937x_dev.c: RGMII internal delay handling for MAC. Delay values are retrieved from DTS and updated - lan937x_dev.c: corrected mutex operations for few dev variables - microchip,lan937x.yaml: introduced rx-internal-delay-ps & tx-internal-delay-ps for RGMII internal delay - lan937x_dev.c: Unnecessary mutex_lock has been removed - lan937x_main.c: PHY_INTERFACE_MODE_NA handling for lan937x_phylink_validate - lan937x_main.c: PORT_MIRROR_SNIFFER check in right place - lan937x_main.c: memset is used instead of writing 0's individually in lan937x_port_fdb_add function - lan937x_main.c: Removed \n from NL_SET_ERR_MSG_MOD calls Changes in v3: - Removed settings of cnt_ptr to zero and the memset() added a cleanup patch which moves this into ksz_init_mib_timer(). - Used ret everywhere instead of rc - microchip,lan937x.yaml: Remove mdio compatible - microchip_t1.c: Renaming standard phy registers - tag_ksz.c: LAN937X_TAIL_TAG_OVERRIDE renaming LAN937X_TAIL_TAG_BLOCKING_OVERRIDE - tag_ksz.c: Changed Ingress and Egress naming convention based on Host - tag_ksz.c: converted to skb_mac_header(skb) from (is_link_local_ether_addr(hdr->h_dest)) - lan937x_dev.c: Removed BCAST Storm protection settings since we have Tc commands for them - lan937x_dev.c: Flow control setting in lan937x_port_setup function - lan937x_dev.c: RGMII internal delay added only for cpu port, - lan937x_dev.c: of_get_compatible_child(node, "microchip,lan937x-mdio") to of_get_child_by_name(node, "mdio"); - lan937x_dev.c:lan937x_get_interface API: returned PHY_INTERFACE_MODE_INTERNAL instead of PHY_INTERFACE_MODE_NA - lan937x_main.c: Removed compat interface implementation in lan937x_config_cpu_port() API & dev_info corrected as well - lan937x_main.c: deleted ds->configure_vlan_while_not_filtering = true - lan937x_main.c: Added explanation for lan937x_setup lines - lan937x_main.c: FR_MAX_SIZE correction in lan937x_get_max_mtu API - lan937x_main.c: removed lan937x_port_bridge_flags dummy functions - lan937x_spi.c - mdiobus_unregister to be added to spi_remove function - lan937x_main.c: phy link layer changes - lan937x_main.c: port mirroring: sniff port selection limiting to one port - lan937x_main.c: Changed to global vlan filtering - lan937x_main.c: vlan_table array to structure - lan937x_main.c -Use extack instead of reporting errors to Console - lan937x_main.c - Remove cpu_port addition in vlan_add api - lan937x_main.c - removed pvid resetting Changes in v2: - return check for register read/writes - dt compatible compatible check is added against chip id value - lan937x_internal_t1_tx_phy_write() is renamed to lan937x_internal_phy_write() - lan937x_is_internal_tx_phy_port is renamed to lan937x_is_internal_100BTX_phy_port as it is 100Base-Tx phy - Return value for lan937x_internal_phy_write() is -EOPNOTSUPP in case of failures - Return value for lan937x_internal_phy_read() is 0xffff for non existent phy - cpu_port checking is removed from lan937x_port_stp_state_set() - lan937x_phy_link_validate: 100baseT_Full to 100baseT1_Full - T1 Phy driver is moved to drivers/net/phy/microchip_t1.c - Tx phy driver support will be added later - Legacy switch checkings in dts file are removed. - tag_ksz.c: Re-used ksz9477_rcv for lan937x_rcv - tag_ksz.c: Xmit() & rcv() Comments are corrected w.r.to host - net/dsa/Kconfig: Family skew numbers altered in ascending order - microchip,lan937x.yaml: eth is replaced with ethernet - microchip,lan937x.yaml: spi1 is replaced with spi - microchip,lan937x.yaml: cpu labelling is removed - microchip,lan937x.yaml: port@x value will match the reg value now ====================
-
Arun Ramadoss authored
This patch add the LAN937x part support in the existing ksz_spi_probe. Signed-off-by:
Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arun Ramadoss authored
This patch add support for phylink_mac_config dsa hook. It configures the mac for MII/RMII modes. The RGMII mode will be added in the future patches. Signed-off-by:
-
Arun Ramadoss authored
This patch add support for phylink_mac_link_up. It configures the mac for the speed, flow control and duplex mode. Signed-off-by:
-
Arun Ramadoss authored
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx and Rx Flow control. Signed-off-by:
-
Arun Ramadoss authored
This patch add the support for port_max_mtu, port_change_mtu and port_fast_age dsa functionality. Signed-off-by:
-
Arun Ramadoss authored
This patch register mdio-bus for the lan937x series switch. mdio read and write uses the vphy for accessing the phy register. Signed-off-by:
-
Arun Ramadoss authored
This patch add support for the writing and reading of the phy registers. LAN937x uses the Vphy indirect addressing method for accessing the phys. Signed-off-by:
-
Arun Ramadoss authored
This patch update the ksz_get_tag_protocol to return LAN937x specific tag if the chip id matches one of LAN937x series switch Signed-off-by:
-
Arun Ramadoss authored
Basic DSA driver support for lan937x and the device will be configured through SPI interface. It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the functionality of ksz9477 series switch. drivers/net/dsa/microchip/ path is already part of MAINTAINERS & the new files come under this path. Hence no update needed to the MAINTAINERS Signed-off-by:
-
Arun Ramadoss authored
The ksz9477 and lan937x has few difference in the static and reserved table register 0x041C. For the ksz9477 if the bit 0 is 1 - read operation and 0 - write operation. But for lan937x bit 1:0 used for selecting the read/write operation, 01 - write and 10 - read. To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks & shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then updated the function with masks & shifts based on the switch instead of hard coding it. Signed-off-by:
-
Prasanna Vengateshan authored
The Microchip LAN937X switches have a tagging protocol which is very similar to KSZ tagging. So that the implementation is added to tag_ksz.c and reused common APIs Signed-off-by:
Prasanna Vengateshan <prasanna.vengateshan@microchip.com> Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Prasanna Vengateshan authored
Documentation in .yaml format and updates to the MAINTAINERS Also 'make dt_binding_check' is passed. RGMII internal delay values for the mac is retrieved from rx-internal-delay-ps & tx-internal-delay-ps as per the feedback from v3 patch series. https://lore.kernel.org/netdev/20210802121550.gqgbipqdvp5x76ii@skbuf/ It supports only the delay value of 0ns and 2ns. Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
-
Prasanna Vengateshan authored
*-internal-delay-ps properties would be applicable only for RGMII interface modes. It is changed as per the request. Ran dt_binding_check to confirm nothing is broken. link: https://lore.kernel.org/netdev/d8e5f6a8-a7e1-dabd-f4b4-ea8ea21d0a1d@gmail.com/Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
-
David S. Miller authored
Divya Koppera says: ==================== net: LED feature for LAN8814 PHY Enable LED mode configuration for LAN8814 PHY v2 -> v3: - Fixed compilation issues v1 -> v2: - Updated dt-bindings for micrel,led-mode in LAN8814 PHY ==================== Signed-off-by: -
Divya Koppera authored
LED support for extended mode where LED 1: Enhanced Mode 5 (10M/1000M/Activity) LED 2: Enhanced Mode 4 (100M/1000M/Activity) By default it supports KSZ9031 LED mode Signed-off-by:
Divya Koppera <Divya.Koppera@microchip.com> Signed-off-by:
-
Divya Koppera authored
Enable led-mode configuration for LAN8814 phy Signed-off-by:
-
Eric Dumazet authored
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)" to compute headers length for a TCP packet, but others use more convoluted (but equivalent) ways. Add skb_tcp_all_headers() and skb_inner_tcp_all_headers() helpers to harmonize this a bit. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Jilin Yuan authored
Delete the redundant word 'a'. Signed-off-by:
Jilin Yuan <yuanjilin@cdjrlc.com> Link: https://lore.kernel.org/r/20220630123924.7531-1-yuanjilin@cdjrlc.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jilin Yuan authored
Delete the redundant word 'are'. Signed-off-by:
-
Jilin Yuan authored
Delete the redundant word 'all'. Signed-off-by:
-
Jilin Yuan authored
Delete the redundant word 'the'. Delete the redundant word 'is'. Delete the redundant word 'start'. Delete the redundant word 'checking'. Signed-off-by:
-
Oliver Neukum authored
The driver has long since be converted to dynamic debugging. The internal compile options for more debugging can simply be deleted. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20220630110741.21314-1-oneukum@suse.comSigned-off-by:
-
Clément Léger authored
As stated by Russel King, miic_config() can be called as a result of ethtool setting the configuration while the link is already up. Since the speed is also set in this function, it could potentially modify the current speed that is set. This will only happen if there is no PHY present and we aren't using fixed-link mode. Handle that by storing the current interface mode in the miic_port structure and update the speed only if the interface mode is going to be changed. Signed-off-by:
Clément Léger <clement.leger@bootlin.com> Link: https://lore.kernel.org/r/20220629122003.189397-1-clement.leger@bootlin.comSigned-off-by:
-
Shijith Thotton authored
Made size of operands same in bitwise operations. The patch fixes the klocwork issue, operands in a bitwise operation have different size at line 375 and 483. Signed-off-by:
Shijith Thotton <sthotton@marvell.com> Link: https://lore.kernel.org/r/f4fba33fe4f89b420b4da11d51255e7cc6ea1dbf.1656586269.git.sthotton@marvell.comSigned-off-by:
-
- 01 Jul, 2022 10 commits
-
-
Li kunyu authored
Remove the repeated ';' from code. Signed-off-by:
Li kunyu <kunyu@nfschina.com> Signed-off-by:
-
Bin Chen authored
Support VF rate limiting with NFDK by adding ndo_set_vf_rate to the NFDK ops structure. NFDK is used to communicate via PCIE to NFP-3800 based NICs while NFD3 is used for other NICs supported by the NFP driver. The VF rate limit feature is already supported by the driver for NFD3. Signed-off-by:
Bin Chen <bin.chen@corigine.com> Reviewed-by:
Baowen Zheng <baowen.zheng@corigine.com> Reviewed-by:
Louis Peens <louis.peens@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Oliver Neukum authored
Either you use BIT(x) or 1 << x in the same expression. Mixing them is ridiculous. Go to BIT() Signed-off-by:
-
Li kunyu authored
Remove the repeated ',' from string Signed-off-by:
-
Alaa Mohamed authored
parsing and usage of -t got missed in the previous patch. this patch fixes it Fixes: 816cda9a ("selftests: net: fib_rule_tests: add support to select a test to run") Signed-off-by:
Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com> Signed-off-by:
-
David S. Miller authored
Mat Martineau says: ==================== mptcp: Updates for mem scheduling and SK_RECLAIM In the "net: reduce tcp_memory_allocated inflation" series (merge commit e10b02ee), Eric Dumazet noted that "Removal of SK_RECLAIM_CHUNK and SK_RECLAIM_THRESHOLD is left to MPTCP maintainers as a follow up." Patches 1-3 align MPTCP with the above TCP changes to forward memory allocation, reclaim, and memory scheduling. Patch 4 removes the SK_RECLAIM_* macros as Eric requested. ==================== Signed-off-by:
-
Paolo Abeni authored
There are no more users for the mentioned macros, just drop them. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Paolo Abeni authored
Similar to commit 7c80b038 ("net: fix sk_wmem_schedule() and sk_rmem_schedule() errors"), let the MPTCP receive path schedule exactly the required amount of memory. Signed-off-by:
-
Paolo Abeni authored
After commit 4890b686 ("net: keep sk->sk_forward_alloc as small as possible"), the MPTCP protocol is the last SK_RECLAIM_CHUNK and SK_RECLAIM_THRESHOLD users. Update the MPTCP reclaim schema to match the core/TCP one and drop the mentioned macros. This additionally clean the MPTCP code a bit. Signed-off-by:
-
Paolo Abeni authored
The memory accounting is broken in such exceptional code path, and after commit 4890b686 ("net: keep sk->sk_forward_alloc as small as possible") we can't find much help there. Drop the broken code. Signed-off-by:
-
