Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.

It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LAN743x Ethernet controller provides two independent PTP event
channels. Each one can be used to generate a periodic output from
the PTP clock. The output can be routed to any one of the available
GPIO pins on the device.

The PTP clock API can now be used to:
- select any LAN743x GPIO pin to function as a periodic output
- select either LAN743x PTP event channel to generate the output

The LAN7430 has 4 GPIO pins that are multiplexed with its internal
PHY LED control signals. A pin assigned to the LED control function
will be assigned to the GPIO function if selected for PTP periodic
output.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Unlock new potential in SJA1105 with PTP system timestamping

The SJA1105 being an automotive switch means it is designed to live in a
set-and-forget environment, far from the configure-at-runtime nature of
Linux. Frequently resetting the switch to change its static config means
it loses track of its PTP time, which is not good.

This patch series implements PTP system timestamping for this switch
(using the API introduced for SPI here:
https://www.mail-archive.com/netdev@vger.kernel.org/msg316725.html),
adding the following benefits to the driver:
- When under control of a user space PTP servo loop (ptp4l, phc2sys),
  the loss of sync during a switch reset is much more manageable, and
  the switch still remains in the s2 (locked servo) state.
- When synchronizing the switch using the software technique (based on
  reading clock A and writing the value to clock B, as opposed to
  relying on hardware timestamping), e.g. by using phc2sys, the sync
  accuracy is vastly improved due to the fact that the actual switch PTP
  time can now be more precisely correlated with something of better
  precision (CLOCK_REALTIME). The issue is that SPI transfers are
  inherently bad for measuring time with low jitter, but the newly
  introduced API aims to alleviate that issue somewhat.

This series is also a requirement for a future patch set that adds full
time-aware scheduling offload support for the switch.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The purpose here is to avoid ptp4l fail due to this condition:

  timed out while polling for tx timestamp
  increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
  port 1: send peer delay request failed

So either reset the switch before the management frame was sent, or
after it was timestamped as well, but not in the middle.

The condition may arise either due to a true timeout (i.e. because
re-uploading the static config takes time), or due to the TX timestamp
actually getting lost due to reset. For the former we can increase
tx_timestamp_timeout in userspace, for the latter we need this patch.

Locking all traffic during switch reset does not make sense at all,
though. Forcing all CPU-originated traffic to potentially block waiting
for a sleepable context to send > 800 bytes over SPI is not a good idea.
Flows that are autonomously forwarded by the switch will get dropped
anyway during switch reset no matter what. So just let all other
CPU-originated traffic be dropped as well.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PTP time of the switch is not preserved when uploading a new static
configuration. Work around this hardware oddity by reading its PTP time
before a static config upload, and restoring it afterwards.

Static config changes are expected to occur at runtime even in scenarios
directly related to PTP, i.e. the Time-Aware Scheduler of the switch is
programmed in this way.

Perhaps the larger implication of this patch is that the PTP .gettimex64
and .settime functions need to be exposed to sja1105_main.c, where the
PTP lock needs to be held during this entire process. So their core
implementation needs to move to some common functions which get exposed
in sja1105_ptp.h.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Through the PTP_SYS_OFFSET_EXTENDED ioctl, it is possible for userspace
applications (i.e. phc2sys) to compensate for the delays incurred while
reading the PHC's time.

The task itself of taking the software timestamp is delegated to the SPI
subsystem, through the newly introduced API in struct spi_transfer. The
goal is to cross-timestamp I/O operations on the switch's PTP clock with
values in the local system clock (CLOCK_REALTIME). For that we need to
understand a bit of the hardware internals.

The 'read PTP time' message is a 12 byte structure, first 4 bytes of
which represent the SPI header, and the last 8 bytes represent the
64-bit PTP time. The switch itself starts processing the command
immediately after receiving the last bit of the address, i.e. at the
middle of byte 3 (last byte of header). The PTP time is shadowed to a
buffer register in the switch, and retrieved atomically during the
subsequent SPI frames.

A similar thing goes on for the 'write PTP time' message, although in
that case the switch waits until the 64-bit PTP time becomes fully
available before taking any action. So the byte that needs to be
software-timestamped is byte 11 (last) of the transfer.

The patch creates a common (and local) sja1105_xfer implementation for
the SPI I/O, and offers 3 front-ends:

- sja1105_xfer_u32 and sja1105_xfer_u64: these are capable of optionally
  requesting a PTP timestamp

- sja1105_xfer_buf: this is for large transfers (e.g. the static config
  buffer) and other misc data, and there is no point in giving
  timestamping capabilities to this.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: improve PHY configuration

This series adds helpers to improve and simplify the PHY
configuration on various network chip versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8168c_4_hw_phy_config() duplicates rtl8168c_3_hw_phy_config(),
so we can remove the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Certain integrated PHY's from RTL8168d support extended pages. On page
0x0007 the number of the extended page is written to register 0x1e,
then the registers on the extended page can be accessed. Add a helper
for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the phylib MDIO access functions in more places to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Integrated PHY's from RTL8168d support an indirect access method for
PHY parameters. On page 0x0005 parameter number is written to register
0x05, then the parameter can be accessed via register 0x06.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Integrated PHY's from RTL8168g support an indirect access method for
PHY parameters. On page 0x0a43 parameter number is written to register
0x13, then the parameter can be accessed via register 0x14.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current upstream interface is an all-or-nothing, which is
sub-optimal for future changes, as it doesn't allow the upstream driver
to prepare for the SFP module becoming available, as it is at boot.

Switch to a find-sfp-bus, add-upstream, del-upstream, put-sfp-bus
interface structure instead, which allows the upstream driver to
prepare for a module being available as soon as add-upstream is called.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) BPF sample build fixes from Björn Töpel

 2) Fix powerpc bpf tail call implementation, from Eric Dumazet.

 3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.

 4) Fix crash in ebtables when using dnat target, from Florian Westphal.

 5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
    Fainelli.

 6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.

 7) Various KCSAN fixes all over the networking, from Eric Dumazet.

 8) Memory leaks in mlx5 driver, from Alex Vesker.

 9) SMC interface refcounting fix, from Ursula Braun.

10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.

11) Add a TX lock to synchonize the kTLS TX path properly with crypto
    operations. From Jakub Kicinski.

12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
    Garzarella.

13) Infinite loop in Intel ice driver, from Colin Ian King.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
  ixgbe: need_wakeup flag might not be set for Tx
  i40e: need_wakeup flag might not be set for Tx
  igb/igc: use ktime accessors for skb->tstamp
  i40e: Fix for ethtool -m issue on X722 NIC
  iavf: initialize ITRN registers with correct values
  ice: fix potential infinite loop because loop counter being too small
  qede: fix NULL pointer deref in __qede_remove()
  net: fix data-race in neigh_event_send()
  vsock/virtio: fix sock refcnt holding during the shutdown
  net: ethernet: octeon_mgmt: Account for second possible VLAN header
  mac80211: fix station inactive_time shortly after boot
  net/fq_impl: Switch to kvmalloc() for memory allocation
  mac80211: fix ieee80211_txq_setup_flows() failure path
  ipv4: Fix table id reference in fib_sync_down_addr
  ipv6: fixes rt6_probe() and fib6_nh->last_probe init
  net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
  net: usb: qmi_wwan: add support for DW5821e with eSIM support
  CDC-NCM: handle incomplete transfer of MTU
  nfc: netlink: fix double device reference drop
  NFC: st21nfca: fix double free
  ...

Pull block fixes from Jens Axboe:

 - Two NVMe device removal crash fixes, and a compat fixup for for an
   ioctl that was introduced in this release (Anton, Charles, Max - via
   Keith)

 - Missing error path mutex unlock for drbd (Dan)

 - cgroup writeback fixup on dead memcg (Tejun)

 - blkcg online stats print fix (Tejun)

* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
  cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
  block: drbd: remove a stray unlock in __drbd_send_protocol()
  blkcg: make blkcg_print_stat() print stats only for online blkgs
  nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
  nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
  nvme-rdma: fix a segmentation fault during module unload

Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2019-11-08

This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.

Colin Ian King fixes a potentially wrap-around counter in a for-loop.

Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.

Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.

Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.

Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.

This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.

This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.

Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.

Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.

This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC

Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 92418fb1 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.

Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.

This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255.  Fix this by making i
a u16.

Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Xin Long says:

====================
sctp: update from rfc7829

SCTP-PF was implemented based on a Internet-Draft in 2012:

  https://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05

It's been updated quite a few by rfc7829 in 2016.

This patchset adds the following features:

  1. add SCTP_ADDR_POTENTIALLY_FAILED notification
  2. add pf_expose per netns/sock/asoc
  3. add SCTP_EXPOSE_POTENTIALLY_FAILED_STATE sockopt
  4. add ps_retrans per netns/sock/asoc/transport
     (Primary Path Switchover)
  5. add spt_pathcpthld for SCTP_PEER_ADDR_THLDS sockopt

v1->v2:
  - See Patch 2/5 and Patch 5/5.
v2->v3:
  - See Patch 1/5, 2/5 and 3/5.
v3->v4:
  - See Patch 1/5, 2/5, 3/5 and 4/5.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Section 7.2 of rfc7829: "Peer Address Thresholds (SCTP_PEER_ADDR_THLDS)
Socket Option" extends 'struct sctp_paddrthlds' with 'spt_pathcpthld'
added to allow a user to change ps_retrans per sock/asoc/transport, as
other 2 paddrthlds: pf_retrans, pathmaxrxt.

Note: to not break the user's program, here to support pf_retrans dump
and setting by adding a new sockopt SCTP_PEER_ADDR_THLDS_V2, and a new
structure sctp_paddrthlds_v2 instead of extending sctp_paddrthlds.

Also, when setting ps_retrans, the value is not allowed to be greater
than pf_retrans.

v1->v2:
  - use SCTP_PEER_ADDR_THLDS_V2 to set/get pf_retrans instead,
    as Marcelo and David Laight suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a new feature defined in section 5 of rfc7829: "Primary Path
Switchover". By introducing a new tunable parameter:

  Primary.Switchover.Max.Retrans (PSMR)

The primary path will be changed to another active path when the path
error counter on the old primary path exceeds PSMR, so that "the SCTP
sender is allowed to continue data transmission on a new working path
even when the old primary destination address becomes active again".

This patch is to add this tunable parameter, 'ps_retrans' per netns,
sock, asoc and transport. It also allows a user to change ps_retrans
per netns by sysctl, and ps_retrans per sock/asoc/transport will be
initialized with it.

The check will be done in sctp_do_8_2_transport_strike() when this
feature is enabled.

Note this feature is disabled by initializing 'ps_retrans' per netns
as 0xffff by default, and its value can't be less than 'pf_retrans'
when changing by sysctl.

v3->v4:
  - add define SCTP_PS_RETRANS_MAX 0xffff, and use it on extra2 of
    sysctl 'ps_retrans'.
  - add a new entry for ps_retrans on ip-sysctl.txt.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a sockopt defined in section 7.3 of rfc7829: "Exposing
the Potentially Failed Path State", by which users can change
pf_expose per sock and asoc.

The new sockopt SCTP_EXPOSE_POTENTIALLY_FAILED_STATE is also
known as SCTP_EXPOSE_PF_STATE for short.

v2->v3:
  - return -EINVAL if params.assoc_value > SCTP_PF_EXPOSE_MAX.
  - define SCTP_EXPOSE_PF_STATE SCTP_EXPOSE_POTENTIALLY_FAILED_STATE.
v3->v4:
  - improve changelog.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP Quick failover draft section 5.1, point 5 has been removed
from rfc7829. Instead, "the sender SHOULD (i) notify the Upper
Layer Protocol (ULP) about this state transition", as said in
section 3.2, point 8.

So this patch is to add SCTP_ADDR_POTENTIALLY_FAILED, defined
in section 7.1, "which is reported if the affected address
becomes PF". Also remove transport cwnd's update when moving
from PF back to ACTIVE , which is no longer in rfc7829 either.

Note that ulp_notify will be set to false if asoc->expose is
not 'enabled', according to last patch.

v2->v3:
  - define SCTP_ADDR_PF SCTP_ADDR_POTENTIALLY_FAILED.
v3->v4:
  - initialize spc_state with SCTP_ADDR_AVAILABLE, as Marcelo suggested.
  - check asoc->pf_expose in sctp_assoc_control_transport(), as Marcelo
    suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As said in rfc7829, section 3, point 12:

  The SCTP stack SHOULD expose the PF state of its destination
  addresses to the ULP as well as provide the means to notify the
  ULP of state transitions of its destination addresses from
  active to PF, and vice versa.  However, it is recommended that
  an SCTP stack implementing SCTP-PF also allows for the ULP to be
  kept ignorant of the PF state of its destinations and the
  associated state transitions, thus allowing for retention of the
  simpler state transition model of [RFC4960] in the ULP.

Not only does it allow to expose the PF state to ULP, but also
allow to ignore sctp-pf to ULP.

So this patch is to add pf_expose per netns, sock and asoc. And in
sctp_assoc_control_transport(), ulp_notify will be set to false if
asoc->expose is not 'enabled' in next patch.

It also allows a user to change pf_expose per netns by sysctl, and
pf_expose per sock and asoc will be initialized with it.

Note that pf_expose also works for SCTP_GET_PEER_ADDR_INFO sockopt,
to not allow a user to query the state of a sctp-pf peer address
when pf_expose is 'disabled', as said in section 7.3.

v1->v2:
  - Fix a build warning noticed by Nathan Chancellor.
v2->v3:
  - set pf_expose to UNUSED by default to keep compatible with old
    applications.
v3->v4:
  - add a new entry for pf_expose on ip-sysctl.txt, as Marcelo suggested.
  - change this patch to 1/5, and move sctp_assoc_control_transport
    change into 2/5, as Marcelo suggested.
  - use SCTP_PF_EXPOSE_UNSET instead of SCTP_PF_EXPOSE_UNUSED, and
    set SCTP_PF_EXPOSE_UNSET to 0 in enum, as Marcelo suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:

while true; do
        echo 10 > /sys/bus/netdevsim/new_device
        devlink dev reload netdevsim/netdevsim10 &
        echo 10 > /sys/bus/netdevsim/del_device
done

Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bb ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a simple test for recently added netdevice alternative names.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While rebooting the system with SR-IOV vfs enabled leads
to below crash due to recurrence of __qede_remove() on the VF
devices (first from .shutdown() flow of the VF itself and
another from PF's .shutdown() flow executing pci_disable_sriov())

This patch adds a safeguard in __qede_remove() flow to fix this,
so that driver doesn't attempt to remove "already removed" devices.

[  194.360134] BUG: unable to handle kernel NULL pointer dereference at 00000000000008dc
[  194.360227] IP: [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[  194.360304] PGD 0
[  194.360325] Oops: 0000 [#1] SMP
[  194.360360] Modules linked in: tcp_lp fuse tun bridge stp llc devlink bonding ip_set nfnetlink ib_isert iscsi_target_mod ib_srpt target_core_mod ib_srp scsi_transport_srp scsi_tgt ib_ipoib ib_umad rpcrdma sunrpc rdma_ucm ib_uverbs ib_iser rdma_cm iw_cm ib_cm libiscsi scsi_transport_iscsi dell_smbios iTCO_wdt iTCO_vendor_support dell_wmi_descriptor dcdbas vfat fat pcc_cpufreq skx_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd qedr ib_core pcspkr ses enclosure joydev ipmi_ssif sg i2c_i801 lpc_ich mei_me mei wmi ipmi_si ipmi_devintf ipmi_msghandler tpm_crb acpi_pad acpi_power_meter xfs libcrc32c sd_mod crc_t10dif crct10dif_generic crct10dif_pclmul crct10dif_common crc32c_intel mgag200
[  194.361044]  qede i2c_algo_bit drm_kms_helper qed syscopyarea sysfillrect nvme sysimgblt fb_sys_fops ttm nvme_core mpt3sas crc8 ptp drm pps_core ahci raid_class scsi_transport_sas libahci libata drm_panel_orientation_quirks nfit libnvdimm dm_mirror dm_region_hash dm_log dm_mod [last unloaded: ip_tables]
[  194.361297] CPU: 51 PID: 7996 Comm: reboot Kdump: loaded Not tainted 3.10.0-1062.el7.x86_64 #1
[  194.361359] Hardware name: Dell Inc. PowerEdge MX840c/0740HW, BIOS 2.4.6 10/15/2019
[  194.361412] task: ffff9cea9b360000 ti: ffff9ceabebdc000 task.ti: ffff9ceabebdc000
[  194.361463] RIP: 0010:[<ffffffffc03553c4>]  [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[  194.361534] RSP: 0018:ffff9ceabebdfac0  EFLAGS: 00010282
[  194.361570] RAX: 0000000000000000 RBX: ffff9cd013846098 RCX: 0000000000000000
[  194.361621] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9cd013846098
[  194.361668] RBP: ffff9ceabebdfae8 R08: 0000000000000000 R09: 0000000000000000
[  194.361715] R10: 00000000bfe14201 R11: ffff9ceabfe141e0 R12: 0000000000000000
[  194.361762] R13: ffff9cd013846098 R14: 0000000000000000 R15: ffff9ceab5e48000
[  194.361810] FS:  00007f799c02d880(0000) GS:ffff9ceacb0c0000(0000) knlGS:0000000000000000
[  194.361865] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  194.361903] CR2: 00000000000008dc CR3: 0000001bdac76000 CR4: 00000000007607e0
[  194.361953] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  194.362002] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  194.362051] PKRU: 55555554
[  194.362073] Call Trace:
[  194.362109]  [<ffffffffc0355500>] qede_remove+0x10/0x20 [qede]
[  194.362180]  [<ffffffffb97d0f3e>] pci_device_remove+0x3e/0xc0
[  194.362240]  [<ffffffffb98b3c52>] __device_release_driver+0x82/0xf0
[  194.362285]  [<ffffffffb98b3ce3>] device_release_driver+0x23/0x30
[  194.362343]  [<ffffffffb97c86d4>] pci_stop_bus_device+0x84/0xa0
[  194.362388]  [<ffffffffb97c87e2>] pci_stop_and_remove_bus_device+0x12/0x20
[  194.362450]  [<ffffffffb97f153f>] pci_iov_remove_virtfn+0xaf/0x160
[  194.362496]  [<ffffffffb97f1aec>] sriov_disable+0x3c/0xf0
[  194.362534]  [<ffffffffb97f1bc3>] pci_disable_sriov+0x23/0x30
[  194.362599]  [<ffffffffc02f83c3>] qed_sriov_disable+0x5e3/0x650 [qed]
[  194.362658]  [<ffffffffb9622df6>] ? kfree+0x106/0x140
[  194.362709]  [<ffffffffc02cc0c0>] ? qed_free_stream_mem+0x70/0x90 [qed]
[  194.362754]  [<ffffffffb9622df6>] ? kfree+0x106/0x140
[  194.362803]  [<ffffffffc02cd659>] qed_slowpath_stop+0x1a9/0x1d0 [qed]
[  194.362854]  [<ffffffffc035544e>] __qede_remove+0xae/0x130 [qede]
[  194.362904]  [<ffffffffc03554e0>] qede_shutdown+0x10/0x20 [qede]
[  194.362956]  [<ffffffffb97cf90a>] pci_device_shutdown+0x3a/0x60
[  194.363010]  [<ffffffffb98b180b>] device_shutdown+0xfb/0x1f0
[  194.363066]  [<ffffffffb94b66c6>] kernel_restart_prepare+0x36/0x40
[  194.363107]  [<ffffffffb94b66e2>] kernel_restart+0x12/0x60
[  194.363146]  [<ffffffffb94b6959>] SYSC_reboot+0x229/0x260
[  194.363196]  [<ffffffffb95f200d>] ? handle_mm_fault+0x39d/0x9b0
[  194.363253]  [<ffffffffb942b621>] ? __switch_to+0x151/0x580
[  194.363304]  [<ffffffffb9b7ec28>] ? __schedule+0x448/0x9c0
[  194.363343]  [<ffffffffb94b69fe>] SyS_reboot+0xe/0x10
[  194.363387]  [<ffffffffb9b8bede>] system_call_fastpath+0x25/0x2a
[  194.363430] Code: f9 e9 37 ff ff ff 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 4c 8d af 98 00 00 00 41 54 4c 89 ef 41 89 f4 53 e8 4c e4 55 f9 <80> b8 dc 08 00 00 01 48 89 c3 4c 8d b8 c0 08 00 00 4c 8b b0 c0
[  194.363712] RIP  [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[  194.363764]  RSP <ffff9ceabebdfac0>
[  194.363791] CR2: 00000000000008dc
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KCSAN reported the following data-race [1]

Adding a couple of READ_ONCE()/WRITE_ONCE() should silence it.

Since the report hinted about multiple cpus using the history
concurrently, I added a test avoiding writing on it if the
victim slot already contains the desired value.

[1]

BUG: KCSAN: data-race in fanout_demux_rollover / fanout_demux_rollover

read to 0xffff8880b01786cc of 4 bytes by task 18921 on cpu 1:
 fanout_flow_is_huge net/packet/af_packet.c:1303 [inline]
 fanout_demux_rollover+0x33e/0x3f0 net/packet/af_packet.c:1353
 packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453
 deliver_skb net/core/dev.c:1888 [inline]
 dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958
 xmit_one net/core/dev.c:3195 [inline]
 dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215
 __dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792
 dev_queue_xmit+0x21/0x30 net/core/dev.c:3825
 neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530
 neigh_output include/net/neighbour.h:511 [inline]
 ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116
 __ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
 __ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
 ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
 NF_HOOK_COND include/linux/netfilter.h:294 [inline]
 ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
 dst_output include/net/dst.h:436 [inline]
 ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179
 ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795
 udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173
 udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471
 inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576
 sock_sendmsg_nosec net/socket.c:637 [inline]
 sock_sendmsg+0x9f/0xc0 net/socket.c:657
 ___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311
 __sys_sendmmsg+0x123/0x350 net/socket.c:2413
 __do_sys_sendmmsg net/socket.c:2442 [inline]
 __se_sys_sendmmsg net/socket.c:2439 [inline]
 __x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439
 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

write to 0xffff8880b01786cc of 4 bytes by task 18922 on cpu 0:
 fanout_flow_is_huge net/packet/af_packet.c:1306 [inline]
 fanout_demux_rollover+0x3a4/0x3f0 net/packet/af_packet.c:1353
 packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453
 deliver_skb net/core/dev.c:1888 [inline]
 dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958
 xmit_one net/core/dev.c:3195 [inline]
 dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215
 __dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792
 dev_queue_xmit+0x21/0x30 net/core/dev.c:3825
 neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530
 neigh_output include/net/neighbour.h:511 [inline]
 ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116
 __ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
 __ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
 ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
 NF_HOOK_COND include/linux/netfilter.h:294 [inline]
 ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
 dst_output include/net/dst.h:436 [inline]
 ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179
 ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795
 udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173
 udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471
 inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576
 sock_sendmsg_nosec net/socket.c:637 [inline]
 sock_sendmsg+0x9f/0xc0 net/socket.c:657
 ___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311
 __sys_sendmmsg+0x123/0x350 net/socket.c:2413
 __do_sys_sendmmsg net/socket.c:2442 [inline]
 __se_sys_sendmmsg net/socket.c:2439 [inline]
 __x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439
 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18922 Comm: syz-executor.3 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 3b3a5b0a ("packet: rollover huge flows before small flows")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tuong Lien says:

====================
TIPC Encryption

This series provides TIPC encryption feature, kernel part. There will be
another one in the 'iproute2/tipc' for user space to set key.

v2: add select crypto 'aes(gcm)' for TIPC_CRYPTO in Kconfig
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit adds two netlink commands to TIPC in order for user to be
able to set or remove AEAD keys:
- TIPC_NL_KEY_SET
- TIPC_NL_KEY_FLUSH

When the 'KEY_SET' is given along with the key data, the key will be
initiated and attached to TIPC crypto. On the other hand, the
'KEY_FLUSH' command will remove all existing keys if any.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit offers an option to encrypt and authenticate all messaging,
including the neighbor discovery messages. The currently most advanced
algorithm supported is the AEAD AES-GCM (like IPSec or TLS). All
encryption/decryption is done at the bearer layer, just before leaving
or after entering TIPC.

Supported features:
- Encryption & authentication of all TIPC messages (header + data);
- Two symmetric-key modes: Cluster and Per-node;
- Automatic key switching;
- Key-expired revoking (sequence number wrapped);
- Lock-free encryption/decryption (RCU);
- Asynchronous crypto, Intel AES-NI supported;
- Multiple cipher transforms;
- Logs & statistics;

Two key modes:
- Cluster key mode: One single key is used for both TX & RX in all
nodes in the cluster.
- Per-node key mode: Each nodes in the cluster has one specific TX key.
For RX, a node requires its peers' TX key to be able to decrypt the
messages from those peers.

Key setting from user-space is performed via netlink by a user program
(e.g. the iproute2 'tipc' tool).

Internal key state machine:

                                 Attach    Align(RX)
                                     +-+   +-+
                                     | V   | V
        +---------+      Attach     +---------+
        |  IDLE   |---------------->| PENDING |(user = 0)
        +---------+                 +---------+
           A   A                   Switch|  A
           |   |                         |  |
           |   | Free(switch/revoked)    |  |
     (Free)|   +----------------------+  |  |Timeout
           |              (TX)        |  |  |(RX)
           |                          |  |  |
           |                          |  v  |
        +---------+      Switch     +---------+
        | PASSIVE |<----------------| ACTIVE  |
        +---------+       (RX)      +---------+
        (user = 1)                  (user >= 1)

The number of TFMs is 10 by default and can be changed via the procfs
'net/tipc/max_tfms'. At this moment, as for simplicity, this file is
also used to print the crypto statistics at runtime:

echo 0xfff1 > /proc/sys/net/tipc/max_tfms

The patch defines a new TIPC version (v7) for the encryption message (-
backward compatibility as well). The message is basically encapsulated
as follows:

   +----------------------------------------------------------+
   | TIPCv7 encryption  | Original TIPCv2    | Authentication |
   | header             | packet (encrypted) | Tag            |
   +----------------------------------------------------------+

The throughput is about ~40% for small messages (compared with non-
encryption) and ~9% for large messages. With the support from hardware
crypto i.e. the Intel AES-NI CPU instructions, the throughput increases
upto ~85% for small messages and ~55% for large messages.

By default, the new feature is inactive (i.e. no encryption) until user
sets a key for TIPC. There is however also a new option - "TIPC_CRYPTO"
in the kernel configuration to enable/disable the new code when needed.

MAINTAINERS | add two new files 'crypto.h' & 'crypto.c' in tipc
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new structure 'tipc_aead_key' is added to the 'tipc.h' for user to
be able to transfer a key to TIPC in kernel. Netlink will be used for
this purpose in the later commits.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user sets RX key for a peer not existing on the own node, a new
node entry is needed to which the RX key will be attached. However,
since the peer node address (& capabilities) is unknown at that moment,
only the node-ID is provided, this commit allows the creation of a node
with only the data that we call as “preliminary”.

A preliminary node is not the object of the “tipc_node_find()” but the
“tipc_node_find_by_id()”. Once the first message i.e. LINK_CONFIG comes
from that peer, and is successfully decrypted by the own node, the
actual peer node data will be properly updated and the node will
function as usual.

In addition, the node timer always starts when a node object is created
so if a preliminary node is not used, it will be cleaned up.

The later encryption functions will also use the node timer and be able
to create a preliminary node automatically when needed.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

As a need to support the crypto asynchronous operations in the later
commits, apart from the current RCU mechanism for bearer pointer, we
add a 'refcnt' to the bearer object as well.

So, a bearer can be hold via 'tipc_bearer_hold()' without being freed
even though the bearer or interface can be disabled in the meanwhile.
If that happens, the bearer will be released then when the crypto
operation is completed and 'tipc_bearer_put()' is called.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>