Report the PCIe link speed (2.5 or 5 Gbps).
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HW VLAN extraction needs to be configured through FW to work correctly in
virtualization environments.  Remove the direct register manipulation and
rely on FW.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling
e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to
make sure the MAC had completed the PHY configuration.  However,
e1000_lan_init_done_ich8lan() had already been called in one of the two
places where PHY reset occurs for ICHx/PCHx parts, which caused the second
call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already
been checked and cleared.

ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset
in e1000_reset_hw_ich8lan() and the PHY-only reset in
e1000_phy_hw_reset_ich8lan().  There was duplicate code in both paths to be
performed post-reset that are now combined into one new function -
e1000_post_phy_reset_ich8lan().  This cleanup also included moving the
clearing of the PHY Reset Asserted bit in the STATUS register (now done for
all ICH/PCH parts) and the check for the indication from h/w that basic
configuration has completed back to where it previously was in
e1000_get_cfg_done_ich8lan().

iii) Corrected a few comments
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flow control refresh timer value needs to be saved off so that it can
be programmed into the approrpiate register when applicable but without a
reset, e.g. when changing flow control parameters via ethtool.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mac->arc_subsystem was being incorrectly used to flag whether or not
manageability was enabled when it should only be used to state whether the
ARC (Host interface) subsystem is available on a particular MAC _and_ only
valid when any manageability is enabled. The ARC subsystem is currently
only available on 80003es2lan and 82573 parts supported by the driver.

A new flag, has_fwsm, is introduced to be used when checking if
manageability is enabled but only on parts that acutally have an FWSM
register. While the above parts have an FWSM register, there are other
parts that have FWSM but do not have support for the ARC subsystem,
namely 82571/2 and ICHx/PCH.

And then there are parts that have manageability, but do not have either
FWSM register or support for the ARC subsystem - these are 82574 and 82583.

For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no
functional changes, it only corrects the usage of the manageability flags.
For 82574 and 82583, it fixes the incorrect accesses of the non-existent
FWSM register and ARC subsystem as well as corrects the check for
management pass-through.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The force_speed_duplex function pointer was incorrectly set.  Instead of
calling the 82577-specific version it was calling the m88 version which,
among other incorrect things, reset the PHY causing autonegotiation to be
re-enabled in the PHY resulting in the link defaulting to half-duplex.
The 82577-specific force_speed_duplex function also had an issue where
it disabled Auto-MDI-X which caused the link to not come up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After every reset all ICH/PCH parts call this function which acquires the
swflag, performs a workaround on applicable parts and releases the swflag.
There is no reason for parts for which this workaround is not applicable
to acquire and release the swflag so the function should just return
without doing anything for these parts.  This also provides for the
indentation of most of the function contents to be shifted left cleaning up
the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Patch addresses issues when manageability passthrough is enabled, but the
MAC_ADDR_FILTER bit is not set in the MANC register.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

...in e1000_update_nvm_checksum_ich8lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was
blocked), the LSC interrupt generated by s/w to start the watchdog which
started the transmitter was not getting fired by the hardware because bit
24 (the 'other' cause bit) also needed to be set.  Without an active SoL
session, the PHY was reset which caused the h/w to fire the LSC interrupt.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82574/82583 uses different registers/bits to setup manageability filters
than all other parts supported by e1000e; set them accordingly for IPMI
pass-through.  Rename the function to better reflect what it does.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running ethtool online diagnostics with no open interface, there is a
short period of time where the driver relinquishes control of the adapter
during which time AMT (manageability firmware) can put the adapter into an
unknown state resulting in such things as link test failure, hardware hang,
reporting an incorrect link speed, etc.  Resetting the adapter during an
open() resolves this by putting the adapter into a quiescent state.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A couple stack cleanups missed in an earlier patch from Jesse.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.

Support for only NX3031 based cards.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unnecessary remap of the region in bar 0 to access onhip memory
for NX3031.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NX3031 have 64bit on card memory. Fix the limit check to
64MB and remove unnecessary 128bit read/write check.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o For NX3031, MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers
  are obsolete. These register addresses can be used for different
  purpose.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert tipc_msg_* inline routines that are more than one line into
standard functions, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert buf_acquire inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert bearer congestion inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Converts port list inline routines that are more than one line into
standard functions, thereby eliminating a significant amount of
repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Converts nmap inline routines that are more than one line into standard
functions, thereby eliminating a significant amount of repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert address-related inline routines that are more than one
line into standard functions, thereby eliminating a significant
amount of repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These functions have enough code in them such that they
seem like sensible targets for un-inlining.  Prior to doing
that, this adds the tipc_ prefix to the functions, so that
in the event of a panic dump or similar, the subsystem from
which the functions come from is immediately clear.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than live in link.c where they can only be used in that file alone,
these helper routines are better served by being in link.h

Relocated are the following:

	link_working_working
	link_working_unknown
	link_reset_unknown
	link_reset_reset
	link_blocked
	link_congested
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is just a straight return of a field; there is no
value in the abstraction of hiding it behind a function.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate comments in TIPC's main API files that are either obsolete,
incorrect, misleading, or unhelpful.  It also adds in one new comment.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide initial support for displaying overall TIPC status/statistics
information at runtime.  Currently, only version info for the TIPC
kernel module is displayed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make a cosmetic change to the name displayed for the broadcast link,
to better reflect its true nature. Since TIPC utilizes this link to
distribute name table information, in addition to multicast messages
sent by user applications, the prior name "multicast-link" is
no longer appropriate.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate a couple of instances where TIPC's native API send routines
were doing pointless initialization of local variables.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate some unused data structures in the TIPC
configuration service that relate to the handling of link
subscriptions, which were not supported when TIPC 1.5 was
introduced.  If and when support for link subscriptions is
offered in TIPC, these elements may need to be re-introduced.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate an argument in a print statement that has no corresponding
format specification.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate a field of the TIPC port structure that is populated,
but never referenced.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Aviod these link-time errors when IPV6=m, XT_TEE=y:

net/built-in.o: In function `tee_tg_route6':
xt_TEE.c:(.text+0x45ca5): undefined reference to `ip6_route_output'
net/built-in.o: In function `tee_tg6':
xt_TEE.c:(.text+0x45d79): undefined reference to `ip6_local_out'
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/net/wireless/ath/ar9170/usb.c
	drivers/scsi/iscsi_tcp.c
	net/ipv4/ipmr.c

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (applesmc) Correct sysfs fan error handling
  hwmon: (asc7621) Bug fixes

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  kprobes/x86: Fix removed int3 checking order
  perf: Fix static strings treated like dynamic ones

i915_error_object_create() is called from the timer interrupt and hence
can corrupt the KM_USER0 slot.  Use KM_IRQ0 instead.
Reported-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Tested-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>