Pull UBI fixes from Artem Bityutskiy:
 "Just a single fastmap fix plus a regression fix"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubi:
  UBI: Fix invalidate_fastmap()
  UBI: Fix PEB leak in wear_leveling_worker()

Pull ubifs fix from Artem Bityutskiy:
 "Just one patch which fixes the power-cut recovery testing mode.

  I'll start using a single UBI/UBIFS tree instead of 2 trees from now
  on.  So in the future you'll get 1 small pull request instead of 2
  tiny ones"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubifs:
  UBIFS: remove invalid warn msg with tst_recovery enabled

Pull MIPS fixes from Ralf Baechle:
 "These are four patches for three construction sites:

   - Fix register decoding for the combination of multi-core processors
     and multi-threading.

   - Two more fixes that are part of the ongoing DECstation resurrection
     work.  One of these touches a DECstation-only network driver.

   - Finally Markos' trivial build fix for the AP/SP support.

  (With this applied now all MIPS defconfigs are building again)"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
  MIPS: Fix SMP core calculations when using MT support.
  MIPS: DECstation I/O ASIC DMA interrupt handling fix
  MIPS: DECstation HRT initialization rearrangement

Pull x86 platform updates from Matthew Garrett:
 "Nothing amazing here, almost entirely cleanups and minor bugfixes and
  one bit of hardware enablement in the amilo-rfkill driver"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  platform/x86: panasonic-laptop: reuse module_acpi_driver
  samsung-laptop: fix config build error
  platform: x86: remove unnecessary platform_set_drvdata()
  amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
  wmi: parse_wdg() should return kernel error codes
  hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
  platform: replace strict_strto*() with kstrto*()
  x86: irst: use module_acpi_driver to simplify the code
  x86: smartconnect: use module_acpi_driver to simplify the code
  platform samsung-q10: use ACPI instead of direct EC calls
  thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
  thinkpad_acpi: return -NODEV while operating uninitialized LEDs

Pull misc SCSI driver updates from James Bottomley:
 "This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
  ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
  ibmvfc error handling) and the first round of esas2r checker fixes and
  finally the much anticipated big endian additions for megaraid_sas"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
  [SCSI] fnic: fnic Driver Tuneables Exposed through CLI
  [SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
  [SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
  [SCSI] fnic: Remove QUEUE_FULL handling code
  [SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
  [SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
  [SCSI] sd: Fix potential out-of-bounds access
  [SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
  [SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
  [SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
  [SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
  [SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
  [SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
  [SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
  [SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
  [SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
  [SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
  [SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
  [SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
  [SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
  ...

Pull SLAB update from Pekka Enberg:
 "Nothing terribly exciting here apart from Christoph's kmalloc
  unification patches that brings sl[aou]b implementations closer to
  each other"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slab: Use correct GFP_DMA constant
  slub: remove verify_mem_not_deleted()
  mm/sl[aou]b: Move kmallocXXX functions to common code
  mm, slab_common: add 'unlikely' to size check of kmalloc_slab()
  mm/slub.c: beautify code for removing redundancy 'break' statement.
  slub: Remove unnecessary page NULL check
  slub: don't use cpu partial pages on UP
  mm/slub: beautify code for 80 column limitation and tab alignment
  mm/slub: remove 'per_cpu' which is useless variable

Pull input update from Dmitry Torokhov:
 "The only change is David Hermann's new EVIOCREVOKE evdev ioctl that
  allows safely passing file descriptors to input devices to session
  processes and later being able to stop delivery of events through
  these fds so that inactive sessions will no longer receive user input
  that does not belong to them"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: evdev - add EVIOCREVOKE ioctl

Sedat points out that I transposed some letters in "LRU" and wrote "RLU"
instead in one of the new comments explaining the flow.  Let's just fix
it.
Reported-by: Sedat Dilek <sedat.dilek@jpberlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Matt found that commit 27a7c642 ("partitions/efi: account for pmbr
size in lba") caused his GPT formatted eMMC device not to boot.  The
reason is that this commit enforced Linux to always check the lesser of
the whole disk or 2Tib for the pMBR size in LBA.  While most disk
partitioning tools out there create a pMBR with these characteristics,
Microsoft does not, as it always sets the entry to the maximum 32-bit
limitation - even though a drive may be smaller than that[1].

Loosen this check and only verify that the size is either the whole disk
or 0xFFFFFFFF.  No tool in its right mind would set it to any value
other than these.

[1] http://thestarman.pcministry.com/asm/mbr/GPT.htm#GPTPTReported-and-tested-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull writeback fix from Wu Fengguang:
 "A trivial writeback fix"

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: Do not sort b_io list only because of block device inode

The LRU list changes interacted badly with our nr_dentry_unused
accounting, and even worse with the new DCACHE_LRU_LIST bit logic.

This introduces helper functions to make sure everything follows the
proper dcache d_lru list rules: the dentry cache is complicated by the
fact that some of the hotpaths don't even want to look at the LRU list
at all, and the fact that we use the same list entry in the dentry for
both the LRU list and for our temporary shrinking lists when removing
things from the LRU.

The helper functions temporarily have some extra sanity checking for the
flag bits that have to match the current LRU state of the dentry.  We'll
remove that before the final 3.12 release, but considering how easy it
is to get wrong, this first cleanup version has some very particular
sanity checking.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull hwmon fixes from Guenter Roeck:
 "Some more low risk cleanup patches:

   - Remove unnecessary pci_set_drvdata in k10temp driver from Jingoo Han
   - Fix return values in several drivers from Sachin Kamat
   - Remove redundant break in amc6821 driver from Sachin Kamat"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (k10temp) remove unnecessary pci_set_drvdata()
  hwmon: (tmp421) Fix return value
  hwmon: (amc6821) Remove redundant break
  hwmon: (amc6821) Fix return value
  hwmon: (ibmaem) Fix return value
  hwmon: (emc2103) Fix return value

Pull Xtensa updates from Chris Zankel.

* tag 'xtensa-next-20130912' of git://github.com/czankel/xtensa-linux:
  xtensa: Fix broken allmodconfig build
  xtensa: remove CCOUNT_PER_JIFFY
  xtensa: fix !CONFIG_XTENSA_CALIBRATE_CCOUNT build failure
  xtensa: don't use echo -e needlessly
  xtensa: new fast_alloca handler
  xtensa: keep a3 and excsave1 on entry to exception handlers
  xtensa: enable kernel preemption
  xtensa: check thread flags atomically on return from user exception

Pull aio changes from Ben LaHaise:
 "First off, sorry for this pull request being late in the merge window.
  Al had raised a couple of concerns about 2 items in the series below.
  I addressed the first issue (the race introduced by Gu's use of
  mm_populate()), but he has not provided any further details on how he
  wants to rework the anon_inode.c changes (which were sent out months
  ago but have yet to be commented on).

  The bulk of the changes have been sitting in the -next tree for a few
  months, with all the issues raised being addressed"

* git://git.kvack.org/~bcrl/aio-next: (22 commits)
  aio: rcu_read_lock protection for new rcu_dereference calls
  aio: fix race in ring buffer page lookup introduced by page migration support
  aio: fix rcu sparse warnings introduced by ioctx table lookup patch
  aio: remove unnecessary debugging from aio_free_ring()
  aio: table lookup: verify ctx pointer
  staging/lustre: kiocb->ki_left is removed
  aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
  aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
  aio: convert the ioctx list to table lookup v3
  aio: double aio_max_nr in calculations
  aio: Kill ki_dtor
  aio: Kill ki_users
  aio: Kill unneeded kiocb members
  aio: Kill aio_rw_vect_retry()
  aio: Don't use ctx->tail unnecessarily
  aio: io_cancel() no longer returns the io_event
  aio: percpu ioctx refcount
  aio: percpu reqs_available
  aio: reqs_active -> reqs_available
  aio: fix build when migration is disabled
  ...

Pull generic hardirq option removal from Martin Schwidefsky:
 "All architectures now use generic hardirqs, s390 has been last to
  switch.

  With that the code under !CONFIG_GENERIC_HARDIRQS and the related
  HAVE_GENERIC_HARDIRQS and GENERIC_HARDIRQS config options can be
  removed.  Yay!"

* 'genirq' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  Remove GENERIC_HARDIRQ config option

Pull kconfig fix from Michal Marek:
 "This is a fix for a regression caused by my previous pull request.

  A sed command in scripts/config that used colons as separator was
  accidentally changed to use slashes, which fails when you use slashes
  in a value.  Changing it back to colons is of course not a proper fix,
  but at least it will be broken in the same way it had been for four
  years.  A proper fix is pending"

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/config: fix variable substitution command

Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux

Pull blackfin updates from Steven Miao.

* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
  blackfin: Ignore generated uImages
  blackfin: Add STMMAC platform data to enable dwmac1000 driver on BF60x.
  bf609: adv7343: add S-Video and Component output support
  bf609: add adv7343 video encoder support
  clock: add stmmac clock for ethernet driver
  blackfin: scb: Add SCB1 to SCB9 config options and data.
  blackfin: scb: Add system crossbar init code.

Pull crypto fixes from Herbert Xu:
 "This fixes a 7+ year race condition in the crypto API that causes
  sporadic crashes when multiple threads load the same algorithm.

  It also fixes the crct10dif algorithm again to prevent boot failures
  on systems where the initramfs tool ignores module softdeps"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: crct10dif - Add fallback for broken initrds
  crypto: api - Fix race condition in larval lookup

Commit 567b21e9
"mips: convert vpe_class to use dev_groups"

broke the build on MIPS since vpe_attrs should be an array
of 'struct device_attribute' pointers.

Fixes the following build problem:
arch/mips/kernel/vpe.c:1372:2: error: missing braces around initializer
[-Werror=missing-braces]
arch/mips/kernel/vpe.c:1372:2: error: (near initialization for 'vpe_attrs[0]')
[-Werror=missing-braces]

Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5819/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Commit 229455bc02b87f7128f190c4491b4ceffff38648 accidentally changed the
separator between sed `s' command and its parameters from ':' to '/'.

Revert this change.
Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Clement Chauplannaz <chauplac@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>

The TCBIND register is only available if the core has MT support. It
should not be read otherwise. Secondly, the number of TCs (siblings)
are calculated differently depending on if the kernel is configured
as SMVP or SMTC.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5822/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Not all I/O ASIC versions have the free-running counter implemented, an
early revision used in the 5000/1xx models aka 3MIN and 4MIN did not have
it.  Therefore we cannot unconditionally use it as a clock source.
Fortunately if not implemented its register slot has a fixed value so it
is enough if we check for the value at the end of the calibration period
being the same as at the beginning.

This also means we need to look for another high-precision clock source on
the systems affected.  The 5000/1xx can have an R4000SC processor
installed where the CP0 Count register can be used as a clock source.
Unfortunately all the R4k DECstations suffer from the missed timer
interrupt on CP0 Count reads erratum, so we cannot use the CP0 timer as a
clock source and a clock event both at a time.  However we never need an
R4k clock event device because all DECstations have a DS1287A RTC chip
whose periodic interrupt can be used as a clock source.

This gives us the following four configuration possibilities for I/O ASIC
DECstations:

1. No I/O ASIC counter and no CP0 timer, e.g. R3k 5000/1xx (3MIN).

2. No I/O ASIC counter but the CP0 timer, i.e. R4k 5000/150 (4MIN).

3. The I/O ASIC counter but no CP0 timer, e.g. R3k 5000/240 (3MAX+).

4. The I/O ASIC counter and the CP0 timer, e.g. R4k 5000/260 (4MAX+).

For #1 and #2 this change stops the I/O ASIC free-running counter from
being installed as a clock source of a 0Hz frequency.  For #2 it also
arranges for the CP0 timer to be used as a clock source rather than a
clock event device, because having an accurate wall clock is more
important than a high-precision interval timer.  For #3 there is no
change.  For #4 the change makes the I/O ASIC free-running counter
installed as a clock source so that the CP0 timer can be used as a clock
event device.

Unfortunately the use of the CP0 timer as a clock event device relies on a
succesful completion of c0_compare_interrupt.  That never happens, because
while waiting for a CP0 Compare interrupt to happen the function spins in
a loop reading the CP0 Count register.  This makes the CP0 Count erratum
trigger reliably causing the interrupt waited for to be lost in all cases.
As a result #4 resorts to using the CP0 timer as a clock source as well,
just as #2.  However we want to keep this separate arrangement in case
(hope) c0_compare_interrupt is eventually rewritten such that it avoids
the erratum.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5825/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We have the build infrastructure to generate uImages so we should ignore
the resulting generated files.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>

- Enable GMAC
- Set propler DMA PBL
- Disable DMA store and forward mode
- Select PTP input clock from MII
clock.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

If SCB exists in select blackfin cpu, developer can change the SCB
priority in kernel configuration.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>

Pull MIPS updates from Ralf Baechle:
 "This has been sitting in -next for a while with no objections and all
  MIPS defconfigs except one are building fine; that one platform got
  broken by another patch in your tree and I'm going to submit a patch
  separately.

   - a handful of fixes that didn't make 3.11
   - a few bits of Octeon 3 support with more to come for a later
     release
   - platform enhancements for Octeon, ath79, Lantiq, Netlogic and
     Ralink SOCs
   - a GPIO driver for the Octeon
   - some dusting off of the DECstation code
   - the usual dose of cleanups"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
  MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
  MIPS: kexec: Fix random crashes while loading crashkernel
  MIPS: kdump: Skip walking indirection page for crashkernels
  MIPS: DECstation HRT calibration bug fixes
  MIPS: Export copy_from_user_page() (needed by lustre)
  MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
  MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
  MIPS: ralink: Add support for reset-controller API
  MIPS: ralink: mt7620: Add cpu-feature-override header
  MIPS: ralink: mt7620: Add spi clock definition
  MIPS: ralink: mt7620: Add wdt clock definition
  MIPS: ralink: mt7620: Improve clock frequency detection
  MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
  MIPS: ralink: mt7620: Add verbose ram info
  MIPS: ralink: Probe clocksources from OF
  MIPS: ralink: Add support for systick timer found on newer ralink SoC
  MIPS: ralink: Add support for periodic timer irq
  MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
  MIPS: Netlogic: Add support for USB on XLP2xx
  MIPS: Netlogic: XLP2xx update for I2C controller
  ...

Pull xfs update #2 from Ben Myers:
 "Here we have defrag support for v5 superblock, a number of bugfixes
  and a cleanup or two.

   - defrag support for CRC filesystems
   - fix endian worning in xlog_recover_get_buf_lsn
   - fixes for sparse warnings
   - fix for assert in xfs_dir3_leaf_hdr_from_disk
   - fix for log recovery of remote symlinks
   - fix for log recovery of btree root splits
   - fixes formemory allocation failures with ACLs
   - fix for assert in xfs_buf_item_relse
   - fix for assert in xfs_inode_buf_verify
   - fix an assignment in an assert that should be a test in
     xfs_bmbt_change_owner
   - remove dead code in xlog_recover_inode_pass2"

* tag 'xfs-for-linus-v3.12-rc1-2' of git://oss.sgi.com/xfs/xfs:
  xfs: remove dead code from xlog_recover_inode_pass2
  xfs: = vs == typo in ASSERT()
  xfs: don't assert fail on bad inode numbers
  xfs: aborted buf items can be in the AIL.
  xfs: factor all the kmalloc-or-vmalloc fallback allocations
  xfs: fix memory allocation failures with ACLs
  xfs: ensure we copy buffer type in da btree root splits
  xfs: set remote symlink buffer type for recovery
  xfs: recovery of swap extents operations for CRC filesystems
  xfs: swap extents operations for CRC filesystems
  xfs: check magic numbers in dir3 leaf verifier first
  xfs: fix some minor sparse warnings
  xfs: fix endian warning in xlog_recover_get_buf_lsn()

Pull SCSI target updates from Nicholas Bellinger:
 "Lots of activity again this round for I/O performance optimizations
  (per-cpu IDA pre-allocation for vhost + iscsi/target), and the
  addition of new fabric independent features to target-core
  (COMPARE_AND_WRITE + EXTENDED_COPY).

  The main highlights include:

   - Support for iscsi-target login multiplexing across individual
     network portals
   - Generic Per-cpu IDA logic (kent + akpm + clameter)
   - Conversion of vhost to use per-cpu IDA pre-allocation for
     descriptors, SGLs and userspace page pointer list
   - Conversion of iscsi-target + iser-target to use per-cpu IDA
     pre-allocation for descriptors
   - Add support for generic COMPARE_AND_WRITE (AtomicTestandSet)
     emulation for virtual backend drivers
   - Add support for generic EXTENDED_COPY (CopyOffload) emulation for
     virtual backend drivers.
   - Add support for fast memory registration mode to iser-target (Vu)

  The patches to add COMPARE_AND_WRITE and EXTENDED_COPY support are of
  particular significance, which make us the first and only open source
  target to support the full set of VAAI primitives.

  Currently Linux clients are lacking upstream support to actually
  utilize these primitives.  However, with server side support now in
  place for folks like MKP + ZAB working on the client, this logic once
  reserved for the highest end of storage arrays, can now be run in VMs
  on their laptops"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
  target/iscsi: Bump versions to v4.1.0
  target: Update copyright ownership/year information to 2013
  iscsi-target: Bump default TCP listen backlog to 256
  target: Fix >= v3.9+ regression in PR APTPL + ALUA metadata write-out
  iscsi-target; Bump default CmdSN Depth to 64
  iscsi-target: Remove unnecessary wait_for_completion in iscsi_get_thread_set
  iscsi-target: Add thread_set->ts_activate_sem + use common deallocate
  iscsi-target: Fix race with thread_pre_handler flush_signals + ISCSI_THREAD_SET_DIE
  target: remove unused including <linux/version.h>
  iser-target: introduce fast memory registration mode (FRWR)
  iser-target: generalize rdma memory registration and cleanup
  iser-target: move rdma wr processing to a shared function
  target: Enable global EXTENDED_COPY setup/release
  target: Add Third Party Copy (3PC) bit in INQUIRY response
  target: Enable EXTENDED_COPY setup in spc_parse_cdb
  target: Add support for EXTENDED_COPY copy offload emulation
  target: Avoid non-existent tg_pt_gp_mem in target_alua_state_check
  target: Add global device list for EXTENDED_COPY
  target: Make helpers non static for EXTENDED_COPY command setup
  target: Make spc_parse_naa_6h_vendor_specific non static
  ...

Merge more patches from Andrew Morton:
 "The rest of MM.  Plus one misc cleanup"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
  mm/Kconfig: add MMU dependency for MIGRATION.
  kernel: replace strict_strto*() with kstrto*()
  mm, thp: count thp_fault_fallback anytime thp fault fails
  thp: consolidate code between handle_mm_fault() and do_huge_pmd_anonymous_page()
  thp: do_huge_pmd_anonymous_page() cleanup
  thp: move maybe_pmd_mkwrite() out of mk_huge_pmd()
  mm: cleanup add_to_page_cache_locked()
  thp: account anon transparent huge pages into NR_ANON_PAGES
  truncate: drop 'oldsize' truncate_pagecache() parameter
  mm: make lru_add_drain_all() selective
  memcg: document cgroup dirty/writeback memory statistics
  memcg: add per cgroup writeback pages accounting
  memcg: check for proper lock held in mem_cgroup_update_page_stat
  memcg: remove MEMCG_NR_FILE_MAPPED
  memcg: reduce function dereference
  memcg: avoid overflow caused by PAGE_ALIGN
  memcg: rename RESOURCE_MAX to RES_COUNTER_MAX
  memcg: correct RESOURCE_MAX to ULLONG_MAX
  mm: memcg: do not trap chargers with full callstack on OOM
  mm: memcg: rework and document OOM waiting and wakeup
  ...

MIGRATION must depend on MMU, or allmodconfig for the nommu sh
architecture fails to build:

    CC      mm/migrate.o
  mm/migrate.c: In function 'remove_migration_pte':
  mm/migrate.c:134:3: error: implicit declaration of function 'pmd_trans_huge' [-Werror=implicit-function-declaration]
     if (pmd_trans_huge(*pmd))
     ^
  mm/migrate.c:149:2: error: implicit declaration of function 'is_swap_pte' [-Werror=implicit-function-declaration]
    if (!is_swap_pte(pte))
    ^
  ...

Also let CMA depend on MMU, or when NOMMU, if we select CMA, it will
select MIGRATION by force.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The usage of strict_strto*() is not preferred, because strict_strto*() is
obsolete.  Thus, kstrto*() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently, thp_fault_fallback in vmstat only gets incremented if a
hugepage allocation fails.  If current's memcg hits its limit or the page
fault handler returns an error, it is incorrectly accounted as a
successful thp_fault_alloc.

Count thp_fault_fallback anytime the page fault handler falls back to
using regular pages and only count thp_fault_alloc when a hugepage has
actually been faulted.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

do_huge_pmd_anonymous_page() has copy-pasted piece of handle_mm_fault()
to handle fallback path.

Let's consolidate code back by introducing VM_FAULT_FALLBACK return
code.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Minor cleanup: unindent most code of the fucntion by inverting one
condition.  It's preparation for the next patch.

No functional changes.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>