Add missing return value check in st_lsm6dsx_shub_read_oneshot disabling
the slave device connected to the st_lsm6dsx i2c controller.
The issue is reported by coverity with the following error:

Unchecked return value:
If the function returns an error value, the error value may be mistaken
for a normal value.

Addresses-Coverity-ID: 1456767 ("Unchecked return value")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add Beniamin Bia and Michael Hennerich as maintainers for HMC425A
attenuator.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Document support for Analog Devices MC425A Step Attenuator.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds support for the HMC425A 0.5 dB LSB GaAs MMIC 6-BIT
DIGITAL POSITIVE CONTROL ATTENUATOR, 2.2 - 8.0 GHz.

Datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/hmc425A.pdfSigned-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch add write_raw_get_fmt function to specify conversion for
hardware gain.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch handles the db suffix used for writing micro db values.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The stm32-timer-cnt driver doesn't use the iio interface. The iio headers
aren't relevant and can be removed as reported by William in [1].
With this change, mod_devicetable.h needs to be added to define the
'of_device_id' struct.

[1] https://lkml.org/lkml/2020/2/10/1516Reported-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add suspend/resume PM sleep ops. When going to low power, enforce the
counter isn't active. Gracefully restore its state upon resume in case
it's been left enabled prior to suspend.
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add missing mpu6000 and new icm20609, icm20689, icm20690, and
iam20680.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

As every chip has some little variant in LPF bandwidth values,
use common values that are working for all chips.
Simplify the LPF setting function.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Same generation as ICM20602 but different registers.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Automotive certified IMU, similar to ICM20608.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

They are similar to ICM20608 chip.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use device_get_match_data for using of and acpi tables.
In spi support add missing mpu6515 and of match table.
Reorganize Kconfig to display chips grouped by generations.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Modify NPCM ADC reset support from
direct register access to reset controller support.

please make sure to modify NPCM adc device tree
parameters as described at nuvoton,npcm-adc.txt
document for using this change.

Note for anyone noting that this is a breaking change, this is on
a BMC and effectively in a close ecosystem so it is fine to rely
on DT and kernel being updated together.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add NPCM ADC reset binding documentation.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This is modelled after the vcnl4035 driver. For the vcnl40{0,1,2}0
we don't do anything since they use on demand measurement.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This will be useful when introducing runtime pm.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

These two defines are unused since the driver was introduced in commit
02b829f9 ("iio: dac: Add support for ltc2632 DACs").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The only difference between LTC2632 and LTC2636 is that the former has
two DAC channels while the latter has eight.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The channel data for ltc2632l12 and ltc2632h12 are identical. So there
is no gain in using two different (but identical) channel descriptions.
The only side effect of this change is some memory savings.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ltc2636 family of devices is register compatible with the ltc2636
chips, it just features 8 instead of 2 channels.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add suspend and resume operations for being used by optional power
management.

The suspend function is switching off an GPIO which can be used by the
hardware to switch power off. The resume function is switching the GPIO
on and sleeps an adjustable time to give the device a chance to be up
and running.

If activated the driver gets into autosuspend after some time of
inactivity.
Suggested-by: Franz Parzer <rpi-receiver@htl-steyr.ac.at>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add GPIO line and startup time for usage of power management
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

A null pointer deference on pdata can occur if the allocation of
pdata fails.  Fix this by adding a null pointer check and handle
the -ENOMEM failure in the caller.

Addresses-Coverity: ("Dereference null return value")
Fixes: 3ce85cc4 ("iio: st_sensors: get platform data from device tree")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds the LOW_PASS_FILTER_3DB_FREQUENCY attribute
in iio_chan_spec for each channel. The used filters are sinc3
or sinc4. The filter type with the highest output data rate
is used when setting a low pass frequency in the channel's sysfs.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There is a spelling mistake and grammar mistake in a dev_err
message. Fix it.

Also include Joe Perches' additional suggestions around:
* Missing newlines
* Excess braces
* Odd indentation
* Some grammar
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Suggested-by: Joe Perches <joe@perches.com> # Additional cleanups etc.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This driver handles two different Sharp sensors that have been
proposed for merging to the mainline kernel over the years, and
already has a limited proximity-only driver in the input
subsystem.

These components are completely different from the confusingly
similarly named Sharp GP2AP020A00F, for which we have a driver
in drivers/iio/light/gp2ap020a00f.c

The two components GP2AP002A00F and GP2AP002S00F are
distinctively different but similar: they share the same set of
registers but differ slightly in the I2C protocol.

Instead of the approach by the previous input driver, we create
a combined IIO proximity and light sensor driver.

The plan is to merge this driver and delete the input driver.

The pieces for the driver are picked all over the place after
researching and grepping through a few different vendor trees
and driver submissions.

We merge it under the light sensors because:

- It has similarities with the Capella CM3605 light sensor and
  proximity driver which is there.

- It is related to the GP2AP020A00F driver which is also there.

This driver was tested with the Samsung GT-S7710 mobile phone
which has the GP2AP002S00F proximity sensor mounted.

The suspend/resume cycle will disable the interrupt from the
sensor. If someone would desire to use this interrupt for
wakeup, the driver will need modifications.

Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Jonathan Bakker <xc-racer2@live.ca>
Cc: Oskar Andero <oskar.andero@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This adds device tree bindings for the GP2AP002 light
and proximity sensor.

As with other early proximity sensors (~2010) the light
sensor and proximity sensors were combined into a single
component.

Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Jonathan Bakker <xc-racer2@live.ca>
Cc: Oskar Andero <oskar.andero@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

odr to odr_table
gain to fs_table

'gain' is actually in 'st_lsm6dsx_fs' structure of 'fs_table'
Signed-off-by: JieunKim <jieun.kim4758@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use st_sensors_dev_name_probe() instead open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Convert the STM32 ADC binding to DT schema format using json-schema
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This reverts commit 075a1e87. Now that
the build issues have been fixed we can resume build testing.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200205001116.14096-7-chris.packham@alliedtelesis.co.nzSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the typedef and update usage to use the union.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200205001116.14096-6-chris.packham@alliedtelesis.co.nzSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove declaration of union cvmx_helper_link_info as typedef and update
uses to use the union.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200205001116.14096-5-chris.packham@alliedtelesis.co.nzSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove typedef declaration from struct cvmx_wqe and replace its previous
uses with new struct declaration.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200205001116.14096-4-chris.packham@alliedtelesis.co.nzSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 710d7fbe.
Re-instate the code so subsequent commits can clean it up and get it
building properly.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200205001116.14096-3-chris.packham@alliedtelesis.co.nzSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 95ace52e. Re-instate
the code so subsequent commits can clean it up and get it building
properly.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200205001116.14096-2-chris.packham@alliedtelesis.co.nzSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's been over 6 months, and no one has noticed that these drivers are
deleted, probably because no one actually has this hardware.  As no one
has volunteered to maintain the code, let's drop it for good.

Link: https://lore.kernel.org/r/20200210231417.GA1736729@kroah.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor handling of P2P specific action frames. Make use of 'struct' to
handle the P2P frames instead of manipulating using 'buf' pointer.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Link: https://lore.kernel.org/r/20200212154503.8835-1-ajay.kathat@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>