Several small code and performance improvements in stack TX datapath,
including:
- Compiler branch predictor hints.
- Minimize variables scope.
- Move tx_info non-inline flow handling to a separate function.
- Calculate data_offset in compile time rather than in runtime
  (for !lso_header_size branch).
- Avoid trinary-operator ("?") when value can be preset in a matching
  branch.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

Gain is too small to be measurable, no degradation sensed.
Results are similar for IPv4 and IPv6.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several small performance improvements in TX CQ polling,
including:
- Compiler branch predictor hints.
- Minimize variables scope.
- More proper check of cq type.
- Use boolean instead of int for a binary indication.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

Packet-rate tests for both regular stack and XDP use cases:
No noticeable gain, no degradation.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several small performance improvements in RX datapath,
including:
- Compiler branch predictor hints.
- Replace a multiplication with a shift operation.
- Minimize variables scope.
- Write-prefetch for packet header.
- Avoid trinary-operator ("?") when value can be preset in a matching
  branch.
- Save a branch by updating RX ring doorbell within
  mlx4_en_refill_rx_buffers(), which now returns void.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Single queue no-RSS optimization ON
(enable by ethtool -L <interface> rx 1).

XDP_DROP packet rate:
Same (28.1 Mpps), lower CPU utilization (from ~100% to ~92%).

Drop packets in TC:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 4.14 Mpps | 4.18 Mpps |   1% |
-------------------------------------

XDP_TX packet rate:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 10.1 Mpps | 10.3 Mpps |   2% |
IPv6 | 10.1 Mpps | 10.3 Mpps |   2% |
-------------------------------------
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid touching RX QP RSS context when loading with only
one RX ring, to allow optimized A0 RX steering.

Enable by:
- loading mlx4_core with module param: log_num_mgm_entry_size = -6.
- then: ethtool -L <interface> rx 1

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

XDP_DROP packet rate:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 20.5 Mpps | 28.1 Mpps |  37% |
IPv6 | 18.4 Mpps | 28.1 Mpps |  53% |
-------------------------------------
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove owner argument, as it is obsolete and unused.
This also saves the overhead of calculating its value in data-path.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Value assigned to variable _data32_ at lines 1254 and 1257 is
overwritten at line 1260 before it can be used. This makes
such variable assignments useless.

Addresses-Coverity-ID: 1227049
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code only assigns the default cpu_dp to all user ports of
the switch to which the CPU port belongs. The user ports of the other
switches of the fabric thus don't have a default CPU port.

This patch fixes this by assigning the cpu_dp of all user ports of all
switches of the fabric when the tree is fully parsed.

Fixes: a29342e7 ("net: dsa: Associate slave network device with CPU port")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: support new chips

These patches are used to support new chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add byte_enable for ocp_read_word() to replace reading 4
bytes data with reading the desired 2 bytes data.

This is used to avoid the issue which is described in
commit b4d99def ("r8152: remove sram_read"). The
original method always reads 4 bytes data, and it may
have problem when reading the PHY registers.

The new method is supported since RTL8153B, but it
doesn't influence the previous chips. The bits of the
byte_enable for the previous chips are the reserved
bits, and the hw would ignore them.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch supports two new chips for RTL8153B.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The settings of the new chip are the same with RTL8152, except that
its product ID is 0x8050.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas Falcon says:

====================
ibmvnic: LPM bug fixes

This series of small patches is meant to resolve a number of
bugs, mostly occurring during an ibmvnic driver reset when
recovering from a logical partition migration (LPM).

The first patch ensures that RX buffer pools are properly
activated following an adapter reset by setting the proper
flag in the pool data structure.

The second patch uses netif_tx_disable to stop TX queues when
closing the device during a reset.

Third, fixup a typo that resulted in partial sanitization of
TX/RX descriptor queues following a device reset.

Fourth, remove an ambiguous conditional check that was resulting
in a kernel panic as null RX/TX completion descriptors were being
processed during napi polling while the device is closing.

Finally, fix a condition where the napi polling routine exits
before it has completed its work budget without notifying the
upper network layers. This omission could result in the
napi_disable function sleeping indefinitely under certain conditions.

v2: Attempt to provide a proper cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug where, in the case of a device reset,
the polling routine will never complete, causing napi_disable
to sleep indefinitely when attempting to close the device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a kernel panic resulting from data access of a NULL
pointer during device close. The pending_scrq routine is
meant to determine whether there is a valid sub-CRQ message
awaiting processing. When the device is closing, however,
there is a possibility that NULL messages can be processed
because pending_scrq will always return 1 even if there
no valid message in the queue.

It's not clear what this closing state check was originally
meant to accomplish, so just remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixup a typo so that the entire SCRQ buffer is cleaned.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netif_tx_disable to guarantee that TX queues are disabled
when __ibmvnic_close is called by the device reset routine.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RX buffer pools are disabled while awaiting a device
reset if firmware indicates that the resource is closed.

This patch fixes a bug where pools were not being
subsequently enabled after the device reset, causing
the device to become inoperable.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As much as we'd like to play well with others, we really aren't
handling the checksums on non-IP protocol packets very well.  This
is easily seen when trying to do TCP over ipv6 - the checksums are
garbage.

Here we restrict the checksum feature flag to just IP traffic so
that we aren't given work we can't yet do.

Orabug: 26175391, 26259755
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Benc says:

====================
net: sched: act_tunnel_key: UDP checksums

Currently, the tunnel_key tc action does not set TUNNEL_CSUM, thus
transmitting packets with zero UDP checksum. This is inconsistent with how
we treat non-lwt UDP tunnels where the default is to fill in the UDP
checksum. Non-zero UDP checksum is the better default anyway for various
reasons previously discussed.

Make this configurable for the tunnel_key tc action with the default being
non-zero checksum. Saves a lot of surprises especially with IPv6.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow requesting of zero UDP checksum for encapsulated packets. The name and
meaning of the attribute is "NO_CSUM" in order to have the same meaning of
the attribute missing and being 0.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's currently no way to request (outer) UDP checksum with
act_tunnel_key. This is problem especially for IPv6. Right now, tunnel_key
action with IPv6 does not work without going through hassles: both sides
have to have udp6zerocsumrx configured on the tunnel interface. This is
obviously not a good solution universally.

It makes more sense to compute the UDP checksum by default even for IPv4.
Just set the default to request the checksum when using act_tunnel_key.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove useless variable rxd_index and code related.

Addresses-Coverity-ID: 1397691
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: prefix Global macros

This patch series is the 2/3 step of the register definitions cleanup.
It brings no functional changes.

It prefixes and documents all Global (1) registers with MV88E6XXX_G1_
(or a specific model like MV88E6352_G1_STS_PPU_STATE), and prefers a
16-bit hexadecimal representation of the Marvell registers layout.

The next and last patchset will prefix the Global 2 registers.
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the remaining Global IP and IEEE Priority and Core
Tag Type registers and give them a clear 16-bit register representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the Global Stats Operation and Counter registers and
give them a clear 16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the Global Monitor Control Register macros
(which became the Global Monitor & MGMT Control Register with 88E6390)
and give a clear 16-bit registers representation.

Use __bf_shf to get the shift value at compile time instead of adding
new defined macros for it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the Global Control and Control 2 registers macros
and give a clear 16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the Global VTU registers macros and give a clear
16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the Global ATU Registers macros and give clear
16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the Global Switch MAC Address Register macros and
give clear 16-bit register representation.

At the same time, move mv88e6xxx_g1_set_switch_mac in global1.c, where
it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix and document the Global Status Register macros and give clear
16-bit register representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's nicer to return void, since then there's no need to
cast to any structures. Currently none of the users have
a cast, but a number of future conversions do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dave Watson says:

====================
net: kernel TLS

This series adds support for kernel TLS encryption over TCP sockets.
A standard TCP socket is converted to a TLS socket using a setsockopt.
Only symmetric crypto is done in the kernel, as well as TLS record
framing.  The handshake remains in userspace, and the negotiated
cipher keys/iv are provided to the TCP socket.

We implemented support for this API in OpenSSL 1.1.0, the code is
available at https://github.com/Mellanox/tls-openssl/tree/master

It should work with any TLS library with similar modifications,
a test tool using gnutls is here: https://github.com/Mellanox/tls-af_ktls_tool

RFC patch to openssl:
https://mta.openssl.org/pipermail/openssl-dev/2017-June/009384.html

Changes from V2:

* EXPORT_SYMBOL_GPL in patch 1
* Ensure cleanup code always called before sk_stream_kill_queues to
  avoid warnings

Changes from V1:

* EXPORT_SYMBOL GPL in patch 2
* Add link to OpenSSL patch & gnutls example in documentation patch.
* sk_write_pending check was rolled in to wait_for_memory path,
  avoids special case and fixes lock inbalance issue.
* Unify flag handling for sendmsg/sendfile

Changes from RFC V2:

* Generic ULP (upper layer protocol) framework instead of TLS specific
  setsockopts
* Dropped Mellanox hardware patches, will come as separate series.
  Framework will work for both.

RFC V2:

http://www.mail-archive.com/netdev@vger.kernel.org/msg160317.html

Changes from RFC V1:

* Socket based on changing TCP proto_ops instead of crypto framework
* Merged code with Mellanox's hardware tls offload
* Zerocopy sendmsg support added - sendpage/sendfile is no longer
  necessary for zerocopy optimization

RFC V1:

http://www.mail-archive.com/netdev@vger.kernel.org/msg88021.html

* Socket based on crypto userspace API framework, required two
  sockets in userspace, one encrypted, one unencrypted.

Paper: https://netdevconf.org/1.2/papers/ktls.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add documentation for the tcp ULP tls interface.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Software implementation of transport layer security, implemented using ULP
infrastructure.  tcp proto_ops are replaced with tls equivalents of sendmsg and
sendpage.

Only symmetric crypto is done in the kernel, keys are passed by setsockopt
after the handshake is complete.  All control messages are supported via CMSG
data - the actual symmetric encryption is the same, just the message type needs
to be passed separately.

For user API, please see Documentation patch.

Pieces that can be shared between hw and sw implementation
are in tls_main.c
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Export do_tcp_sendpages and tcp_rate_check_app_limited, since tls will need to
sendpages while the socket is already locked.

tcp_sendpage is exported, but requires the socket lock to not be held already.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the infrustructure for attaching Upper Layer Protocols (ULPs) over TCP
sockets. Based on a similar infrastructure in tcp_cong.  The idea is that any
ULP can add its own logic by changing the TCP proto_ops structure to its own
methods.

Example usage:

setsockopt(sock, SOL_TCP, TCP_ULP, "tls", sizeof("tls"));

modules will call:
tcp_register_ulp(&tcp_tls_ulp_ops);

to register/unregister their ulp, with an init function and name.

A list of registered ulps will be returned by tcp_get_available_ulp, which is
hooked up to /proc.  Example:

$ cat /proc/sys/net/ipv4/tcp_available_ulp
tls

There is currently no functionality to remove or chain ULPs, but
it should be possible to add these in the future if needed.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arun Parameswaran says:

====================
Add support for Broadcom DTE based PTP clock

This patchset adds support for the DTE based PTP clock for Broadcom SoCs.

The DTE nco based PTP clock can be used in both wired and wireless networks
for precision time-stmaping purposes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a ptp clock driver for the Broadcom SoCs using
the Digital timing Engine (DTE) nco.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree binding documentation for the Broadcom DTE
PTP clock driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>