In the case hcd autosuspend is enabled, the hcd will enter L2 state
if no device connected. But if the controller works in otg mode, the
gadget driver still works in L0 state if connected with host. This
may result in transfer fail when gadget enqueue new request but the
hcd driver has set the global state into L2. This patch prevent the
hcd enter L2 state if the controller work in device mode.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes an issue that the spin_lock_init() is not called
for almost all pipes. Otherwise, the lockdep output the following
message when we connect a usb cable using g_ncm:

 INFO: trying to register non-static key.
 the code is fine but needs lockdep annotation.
 turning off the locking correctness validator.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: b8b9c974 ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In the SG case this is already handled since a non-zero
request->num_mapped_sgs is a clear indicator that dma_map_sg()
had been called. While it would be nice to do the same for the
singly mapped case by simply checking for non-zero request->dma,
it's conceivable that 0 is a valid dma_addr_t handle. Hence add
a flag 'dma_mapped' to struct usb_request and use this to
determine the need to call dma_unmap_single(). Otherwise, if a
request is not DMA mapped then the result of calling
usb_request_unmap_request() would safely be a no-op.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

USB gadget serial console works on functions other than the legacy
configurations. Let the user enable it when using any function that
uses the serial utilities.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The header clk-provider.h is there for clock drivers (providers) to
include, not client drivers (consumers).  That said,
of_clk_get_parent_count() is a helper function for clock providers, not
a clk API for consumers.

Let's replace of_clk_get_parent_count() with of_count_phandle_with_args()
call, so that we can remove the include of clk-provider.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Currenly, f_midi_free uses snd_card_free, which will wait
until the user has released the sound card before
returning. However, if the user doesn't release the sound
card, then f_midi_free can block for an arbitrary amount
of time, which also blocks any gadget operations on that
thread.

Instead, we can use snd_card_free_when_closed which returns
before all handles are released. Since f_midi can be
accessed through rmidi if usb_put_function is called before
release_card_device, add refcounting to f_midi_free and
have rawmidi's private free call it. The f_midi memory
is only kfreed when usb_put_function and release_card_device
have both been called.
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add super speed descriptors for f_midi.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The while loop never terminates because the loop counter i is never
decremented. Fix this by decrementing i.

Detected by CoverityScan, CID#751073 ("Infinite Loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

These snd_rawmidi_ops structures are only passed as the third
argument of snd_rawmidi_set_ops.  This argument is const, so the
snd_rawmidi_ops structures can be const too.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The mtu3 driver is a generic driver for MediaTek usb3 DRD IP, add
a generic compatible to avoid confusion when support new SoCs but
use a compatible with specific SoC's name "mt8173".
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The current f_hid driver doesn't handle GET_PROCOTOL and
SET_PROCOTOL requests, which are required to operate HID
gadgets in BOOT mode. This patch implements this feature for
devices that have the same implementation for REPORT and BOOT mode
so that these devices are recognized by older BIOSes.
Signed-off-by: Abdulhadi Mohamed <abdulahhadi2@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Ip sleep will auto exit if vbus comparison circuit of u2 phy is
disabled when system tries to enter suspend mode, so get vbus-valid
status from mac but not from u2 phy when enable DRD mode to fix
the issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

when the device is reset by host, the status of u1_enable and
u2_enable should also be restored to default value.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add the delayed status handling. This is used by mass storage etc to
gain some extra time to setup its internal status before it can proceed
further requests, and once the gadget is ready, it will enqueue an
empty packet which is used for synchronization.
The issue may happen on some FGPA platform with very low cpu frequency.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Using devm_ioremap_resource() can make the code simpler, as it
already does the resource NULL check.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

qe_ep0_desc is only passed as the second argument to qe_ep_init, which is
const, so qe_ep0_desc can be const too.

Done with the help of Coccinelle.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for R-Car M3-W. This patch also adds R-Car
Gen3 generic version's compatible and changes ".compatible" in
the usb3_of_match from "renesas,r8a7796-usb3-peri" to
"renesas,rcar-gen3-usb3-peri".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for R-Car H3 ES2.0. Since this SoC revision
doesn't need workaround for vbus detection and number of ramif is
increased. So, this driver uses soc_device_match() to detect it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds debugfs to set the "b-device" mode for using a board
which is not connected to the ID pin (e.g. CN11 on Salvator-X).
If we want to use peripheral mode on such a board, we have to disable
VBUS output first. So, this patch can set such a mode as the following:

 # mount -t debugfs none /sys/kernel/debug
 # modprobe renesas_usb3
 # modprobe g_mass_storage file=/dev/shm/test.bin
 # echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add myself as maintainer of MediaTek USB3 DRD IP driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Provides a new vbus debugfs interface used to turn on/off vbus
regulator, it also can be used to get/put reference count of
vbus, due to sometimes we need keep it alive when manually switch
mtu3 to device mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For 66AK2Gx there is a requirement to use PM Runtime to properly manage
clocks and the power domains. Therefore, add PM runtime support. Remove
legacy clock api's calls since other users of this driver worked without
these clock apis calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

platform_get_irq() returns an error code, but the dwc3-omap driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.

Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af

Print and propagate the return value of platform_get_irq on failure.

This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dev_pm_ops is not supposed to change at runtime. Marking it constant.
Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

platform_get_irq() returns an error code, but the renesas_usb3 driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.

Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af

Print error message and propagate the return value of platform_get_irq
on failure.

This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/pcm.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull x86 platform driver fix from Darren Hart:
 "Fix loop preventing some platforms from waking up via the power button
  in s2idle:

   - intel-vbtn: match power button on press rather than release"

* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: intel-vbtn: match power button on press rather than release

Pull ext4 fixes from Ted Ts'o:
 "A large number of ext4 bug fixes and cleanups for v4.13"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix copy paste error in ext4_swap_extents()
  ext4: fix overflow caused by missing cast in ext4_resize_fs()
  ext4, project: expand inode extra size if possible
  ext4: cleanup ext4_expand_extra_isize_ea()
  ext4: restructure ext4_expand_extra_isize
  ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
  ext4: make xattr inode reads faster
  ext4: inplace xattr block update fails to deduplicate blocks
  ext4: remove unused mode parameter
  ext4: fix warning about stack corruption
  ext4: fix dir_nlink behaviour
  ext4: silence array overflow warning
  ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
  ext4: release discard bio after sending discard commands
  ext4: convert swap_inode_data() over to use swap() on most of the fields
  ext4: error should be cleared if ea_inode isn't added to the cache
  ext4: Don't clear SGID when inheriting ACLs
  ext4: preserve i_mode if __ext4_set_acl() fails
  ext4: remove unused metadata accounting variables
  ext4: correct comment references to ext4_ext_direct_IO()

Pull MIPS fixes from Ralf Baechle:
 "This fixes two build issues for ralink platforms, both due to missing
  #includes which used to be included indirectly via other headers"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: mt7620: Add missing header
  MIPS: ralink: Fix build error due to missing header

The latest change of compat_sys_sigpending in commit 8f13621a
("sigpending(): move compat to native") has broken it in two ways.

First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.

Second, on big endian architectures these bytes are being written in the
wrong order.

This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621a ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks.  This may
caused the superblock being corrupted with zero blocks count.

Fixes: 1c6bd717Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+

When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>

Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.

Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>

We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>