This info is already available through ioctl() and /proc

Bart:
- dump 'gcw.packet_size' for unsupported packet sizes
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This flag is not being set anywhere in the driver so it can go.

Bart:
- minor CodingStyle fixup
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We merge idefloppy_{input,output}_buffers() into idefloppy_io_buffers() by
introducing a 4th arg. called direction. According to its value
we atapi_input_bytes() or atapi_output_bytes(). Also, this simplifies the
interrupt handler logic a bit. Finally, rename idefloppy_io_buffers() to
ide_floppy_io_buffers().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Also, move xfer_func_t typedef to the ide.h since it is used by two drivers
now (more coming).

Bart:
- use __func__ while at it
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

In addition to shortening the function name, move the printk-call into the
function thereby saving some code lines. Also, make the function out_of_line
since it is not on a performance critical path. Finally, rename the reworked
function to ide_floppy..().

Bart:
- minor CodingStyle fixup
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Bart:
- use 'hwif' instead of 'HWIF(drive)'
- minor CodingStyle fixup
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

By passing idefloppy_floppy_t *floppy to the factored out functions, we get
rid of (almost) all local vars so stack usage should be at minimum here. Also,
we merge idefloppy_begin_format() into idefloppy_format_start() since it is its
only user. Also, rename idefloppy_format_start() to idefloppy_format_unit().
Finally, rename the reworked functions to ide_floppy..().

Bart
- minor CodingStyle fixup
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Also,
- remove the accompanying 4 byte idefloppy_capacity_header.
- rename functions from idefloppy_... to ide_floppy_... after cleanup.
- simplify loop in ide_floppy_get_capacity() by reversing if-test condition
  logically.
- finally, fix white space and checkpatch.pl issues
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it, collapse idefloppy_analyze_error() into
idefloppy_request_sense_callback() since the latter was its only user.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This change is rather temporary and is in preparation of using generic commands
as is the case with ide-cd and the uniform cdrom layer (i.e. init_cdrom_command())
However, before this happens, we'll have to remove all typedefs and teach
idefloppy_create_mode_sense_cmd() to work directly on u8 buffers.

Also, since idefloppy_get_capability_page() was used to read only the sfrp bit,
rename the latter so that the name reflects what it does.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* some debug_log() calls were not using "ide-floppy: " prefix

* a few used printk levels different than KERN_INFO (KERN_NOTICE
  and KERN_ERR, which is the default one if no level is given)

Bart:
- fix build issues for IDEFLOPPY_DEBUG_LOG set to 1 while at it
- s/__FUNCTION__/__func__/
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There were two almost identical function names in ide-floppy.c, which makes
their distinction almost impossible. While ide_floppy_release() cleans up the
object after the last reference to it has been dropped, idefloppy_release() is
the blkdev .release method from struct block_device_operations which releases
that last reference.

Rename ide_floppy_release() to idefloppy_cleanup_obj() in order to make its
purpose more clear.

There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This BUG_ON is unneeded since the ->handler != NULL check is performed in
ide_set_handler().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Replace the ide-floppy packet commands opcode defines with the generic ones.
Add a missing GPCMD_WRITE_12 (opcode 0xaa) to the generic ones in cdrom.h. The
last one can be found in the current version of INF-8090, p.905.

[ Bart: Tejun's libata patch also adding GPCMD_WRITE_12 got merged first ]
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->cable_detect method to ide_hwif_t.

* Call the new method in ide_init_port() if:
  - the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
  - DMA initialization was successful (if hwif->dma_base is not set
    ide_init_port() sets hwif->ultra_mask to zero)
  - "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')

* Convert PCI host drivers to use ->cable_detect method.

While at it:

* Factor out cable detection to separate functions (if not already done).

* hpt366.c/it8213.c/slc90e66.c:
  - don't check cable type if "idex=ata66" is used

* pdc202xx_new.c:
  - add __devinit tag to pdcnew_cable_detect()

* pdc202xx_old.c:
  - rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
  - add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().

* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.

* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().

* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
  move it to ide-probe.c and call it in in ide_device_add_all() instead of
  ide_pci_setup_ports().

* Move ->mate setup to ide_device_add_all() from ide_port_init().

* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
  ->autotune currently.

* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
  (to not override setup done by ide_hwif_configure()).

* Add ETRAX host handling to ide_device_add_all().

* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.

* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
  setup to pmac_ide_setup_device().

* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
  ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Setup ->mate and ->channel in ide_pci_setup_ports() instead of
  in ide_hwif_configure().

* Make 'port' parameter for ide_hwif_configure() 'unsigned int'.

* Separate PCI specific init from generic init in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Always set DMA masks in ide_pci_setup_ports() to make sure that the valid
masks for a host are set.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Nowadays IDE core always provides drive ID and ide-disk always setups
drive->capacity64 so this quirk is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't override the cable type if the "idex=ata66" parameter was used.

While at it:

* atiixp.c: factor out cable detection to atiixp_cable_detect() from
  init_hwif_atiixp().

* cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to
  cs5535_cable_detect().

* scc_pata.c: factor out cable detection to scc_cable_detect() from
  init_hwif_scc() and remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The host driver must set hwif's ->no_io_32bit setting not drive's one
(ide_port_tune_devices() overrides drive's setting).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On DTC2278 32-bit I/O has to be enabled for both devices on the port
so always enable it during init time and disallow further changes.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* git://git.infradead.org/battery-2.6:
  apm_power: check I.intval for zero value, we use it as the divisor
  MAINTAINERS: remove kernel-discuss@handhelds.org list
  pda_power: implement polling
  pda_power: various cleanups
  apm_power: support using VOLTAGE_* properties for apm calculations
  pda_power: add suspend/resume support
  power_supply: add few more values and props
  pda_power: only register available psu
  power: fix incorrect unregistration in power_supply_create_attrs error path
  power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
  [BATTERY] power_supply_leds: use kasprintf
  [BATTERY] Every file should include the headers containing the prototypes for its global functions.

* 'for-linus' of git://linux-nfs.org/~bfields/linux: (100 commits)
  SUNRPC: RPC program information is stored in unsigned integers
  SUNRPC: Move exported symbol definitions after function declaration part 2
  NLM: tear down RPC clients in nlm_shutdown_hosts
  SUNRPC: spin svc_rqst initialization to its own function
  nfsd: more careful input validation in nfsctl write methods
  lockd: minor log message fix
  knfsd: don't bother mapping putrootfh enoent to eperm
  rdma: makefile
  rdma: ONCRPC RDMA protocol marshalling
  rdma: SVCRDMA sendto
  rdma: SVCRDMA recvfrom
  rdma: SVCRDMA Core Transport Services
  rdma: SVCRDMA Transport Module
  rdma: SVCRMDA Header File
  svc: Add svc_xprt_names service to replace svc_sock_names
  knfsd: Support adding transports by writing portlist file
  svc: Add svc API that queries for a transport instance
  svc: Add /proc/sys/sunrpc/transport files
  svc: Add transport hdr size for defer/revisit
  svc: Move the xprt independent code to the svc_xprt.c file
  ...

* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
  suspend: cleanup reference to swsusp_pg_dir[]
  PM: Remove obsolete /sys/devices/.../power/state docs
  Hibernation: Invoke suspend notifications after console switch
  Suspend: Invoke suspend notifications after console switch
  Suspend: Clean up suspend_64.c
  Suspend: Add config option to disable the freezer if architecture wants that
  ACPI: Print message before calling _PTS
  ACPI hibernation: Call _PTS before suspending devices
  Hibernation: Introduce begin() and end() callbacks
  ACPI suspend: Call _PTS before suspending devices
  ACPI: Separate disabling of GPEs from _PTS
  ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
  Suspend: Introduce begin() and end() callbacks
  suspend: fix ia64 allmodconfig build
  ACPI: clear GPE earily in resume to avoid warning
  Suspend: Clean up Kconfig (V2)
  Hibernation: Clean up Kconfig (V2)
  Hibernation: Update messages
  Suspend: Use common prefix in messages
  Hibernation: Remove unnecessary variable declaration
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
  PCI: make pci_bus a struct device
  PCI: fix codingstyle issues in include/linux/pci.h
  PCI: fix codingstyle issues in drivers/pci/pci.h
  PCI: PCIE ASPM support
  PCI: Fix fakephp deadlock
  PCI: modify SB700 SATA MSI quirk
  PCI: Run ACPI _OSC method on root bridges only
  PCI ACPI: AER driver should only register PCIe devices with _OSC
  PCI ACPI: Added a function to register _OSC with only PCIe devices.
  PCI: constify function pointer tables
  PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
  pciehp: block new requests from the device before power off
  pciehp: workaround against Bad DLLP during power off
  pciehp: wait for 1000ms before LED operation after power off
  PCI: Remove pci_enable_device_bars() from documentation
  PCI: Remove pci_enable_device_bars()
  PCI: Remove users of pci_enable_device_bars()
  PCI: Add pci_enable_device_{io,mem} intefaces
  PCI: avoid save the same type of cap multiple times
  PCI: correctly initialize a structure for pcie_save_pcix_state()
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (128 commits)
  USB: fix codingstyle issues in drivers/usb/core/*.c
  USB: fix codingstyle issues in drivers/usb/core/message.c
  USB: fix codingstyle issues in drivers/usb/core/hcd-pci.c
  USB: fix codingstyle issues in drivers/usb/core/devio.c
  USB: fix codingstyle issues in drivers/usb/core/devices.c
  USB: fix codingstyle issues in drivers/usb/core/*.h
  USB: fix codingstyle issues in include/linux/usb/
  USB: fix codingstyle issues in include/linux/usb.h
  USB: mark USB drivers as being GPL only
  USB: use a real vendor and product id for root hubs
  USB: mount options: fix usbfs
  USB: Fix usb_serial_driver structure for Kobil cardreader driver.
  usb: ehci should use u16 for isochronous intervals
  usb: ehci, remove false clear-reset path
  USB: Use menuconfig objects
  usb: ohci-sm501 driver
  usb: dma bounce buffer support
  USB: last abuses of intfdata in close for usb-serial drivers
  USB: kl5kusb105 don't flush to logically disconnected devices
  USB: oti6858: cleanup
  ...

Rafael J. Wysocki reported weird, multi-seconds delays during
suspend/resume and bisected it back to:

  commit 82a1fcb9
  Author: Ingo Molnar <mingo@elte.hu>
  Date:   Fri Jan 25 21:08:02 2008 +0100

      softlockup: automatically detect hung TASK_UNINTERRUPTIBLE tasks

fix it:

 - restore the old wakeup mechanism
 - fix break usage in do_each_thread() { } while_each_thread().
 - fix the hotplug switch stmt, a fall-through case was broken.
Bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Anton Vorontsov <cbou@mail.ru>

kernel-discuss at handhelds.org is down for months, and nobody
knows why. So remove it for now.
Signed-off-by: Anton Vorontsov <cbou@mail.ru>

Signed-off-by: Anton Vorontsov <cbou@mail.ru>

- handle spurious interrupts correctly;
- get rid of pda_power_supplies array, use two variables instead;
- factor out psy_changed() function, it will be used for polling.
Signed-off-by: Anton Vorontsov <cbou@mail.ru>

It's pretty dummy, but useful for batteries for which we can only
get voltages.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>