- 22 Apr, 2023 1 commit
-
-
Vladimir Oltean authored
The CBTX PHY is a Fast Ethernet PHY integrated into the SJA1110 A/B/C automotive Ethernet switches. It was hoped it would work with the Generic PHY driver, but alas, it doesn't. The most important reason why is that the PHY is powered down by default, and it needs a vendor register to power it on. It has a linear memory map that is accessed over SPI by the SJA1110 switch driver, which exposes a fake MDIO controller. It has the following (and only the following) standard clause 22 registers: 0x0: MII_BMCR 0x1: MII_BMSR 0x2: MII_PHYSID1 0x3: MII_PHYSID2 0x4: MII_ADVERTISE 0x5: MII_LPA 0x6: MII_EXPANSION 0x7: the missing MII_NPAGE for Next Page Transmit Register Every other register is vendor-defined. The register map expands the standard clause 22 5-bit address space of 0x20 registers, however the driver does not need to access the extra registers for now (and hopefully never). If it ever needs to do that, it is possible to implement a fake (software) page switching mechanism between the PHY driver and the SJA1110 MDIO controller driver. Also, Auto-MDIX is turned off by default in hardware, the driver turns it on by default and reports the current status. I've tested this with a VSC8514 link partner and a crossover cable, by forcing the mode on the link partner, and seeing that the CBTX PHY always sees the reverse of the mode forced on the VSC8514 (and that traffic works). The link doesn't come up (as expected) if MDI modes are forced on both ends in the same way (with the cross-over cable, that is). Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230418190141.1040562-1-vladimir.oltean@nxp.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
- 21 Apr, 2023 39 commits
-
-
Jakub Kicinski authored
Merge tag 'wireless-next-2023-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.4 Most likely the last -next pull request for v6.4. We have changes all over. rtw88 now supports SDIO bus and iwlwifi continues to work on Wi-Fi 7 support. Not much stack changes this time. Major changes: cfg80211/mac80211 - fix some Fine Time Measurement (FTM) frames not being bufferable - flush frames before key removal to avoid potential unencrypted transmission depending on the hardware design iwlwifi - preparation for Wi-Fi 7 EHT and multi-link support rtw88 - SDIO bus support - RTL8822BS, RTL8822CS and RTL8821CS SDIO chipset support rtw89 - framework firmware backwards compatibility brcmfmac - Cypress 43439 SDIO support mt76 - mt7921 P2P support - mt7996 mesh A-MSDU support - mt7996 EHT support - mt7996 coredump support wcn36xx - support for pronto v3 hardware ath11k - PCIe DeviceTree bindings - WCN6750: enable SAR support ath10k - convert DeviceTree bindings to YAML * tag 'wireless-next-2023-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (261 commits) wifi: rtw88: Update spelling in main.h wifi: airo: remove ISA_DMA_API dependency wifi: rtl8xxxu: Simplify setting the initial gain wifi: rtl8xxxu: Add rtl8xxxu_write{8,16,32}_{set,clear} wifi: rtl8xxxu: Don't print the vendor/product/serial wifi: rtw88: Fix memory leak in rtw88_usb wifi: rtw88: call rtw8821c_switch_rf_set() according to chip variant wifi: rtw88: set pkg_type correctly for specific rtw8821c variants wifi: rtw88: rtw8821c: Fix rfe_option field width wifi: rtw88: usb: fix priority queue to endpoint mapping wifi: rtw88: 8822c: add iface combination wifi: rtw88: handle station mode concurrent scan with AP mode wifi: rtw88: prevent scan abort with other VIFs wifi: rtw88: refine reserved page flow for AP mode wifi: rtw88: disallow PS during AP mode wifi: rtw88: 8822c: extend reserved page number wifi: rtw88: add port switch for AP mode wifi: rtw88: add bitmap for dynamic port settings wifi: rtw89: mac: use regular int as return type of DLE buffer request wifi: mac80211: remove return value check of debugfs_create_dir() ... ==================== Link: https://lore.kernel.org/r/20230421104726.800BCC433D2@smtp.kernel.orgSigned-off-by:
-
Jianfeng Tan authored
Packet sockets, like tap, can be used as the backend for kernel vhost. In packet sockets, virtio net header size is currently hardcoded to be the size of struct virtio_net_hdr, which is 10 bytes; however, it is not always the case: some virtio features, such as mrg_rxbuf, need virtio net header to be 12-byte long. Mergeable buffers, as a virtio feature, is worthy of supporting: packets that are larger than one-mbuf size will be dropped in vhost worker's handle_rx if mrg_rxbuf feature is not used, but large packets cannot be avoided and increasing mbuf's size is not economical. With this virtio feature enabled by virtio-user, packet sockets with hardcoded 10-byte virtio net header will parse mac head incorrectly in packet_snd by taking the last two bytes of virtio net header as part of mac header. This incorrect mac header parsing will cause packet to be dropped due to invalid ether head checking in later under-layer device packet receiving. By adding extra field vnet_hdr_sz with utilizing holes in struct packet_sock to record currently used virtio net header size and supporting extra sockopt PACKET_VNET_HDR_SZ to set specified vnet_hdr_sz, packet sockets can know the exact length of virtio net header that virtio user gives. In packet_snd, tpacket_snd and packet_recvmsg, instead of using hardcoded virtio net header size, it can get the exact vnet_hdr_sz from corresponding packet_sock, and parse mac header correctly based on this information to avoid the packets being mistakenly dropped. Signed-off-by:
Jianfeng Tan <henry.tjf@antgroup.com> Co-developed-by:
Anqi Shen <amy.saq@antgroup.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Leon Romanovsky says: ==================== Fixes to mlx5 IPsec implementation This small patchset includes various fixes and one refactoring patch which I collected for the features sent in this cycle, with one exception - first patch. First patch fixes code which was introduced in previous cycle, however I was able to trigger FW error only in custom debug code, so don't see a need to send it to net-rc. ==================== Signed-off-by: -
Leon Romanovsky authored
ARP discovery code has same logic for RX and TX flows, but with different source and destination fields. Instead of duplicating same code in mlx5e_ipsec_init_macs, let's refactor. Signed-off-by:
Leon Romanovsky <leonro@nvidia.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Leon Romanovsky authored
There are some flows in which work structure is not allocated at all and it is needed to be checked prior release of data structure. general protection fault, probably for non-canonical address 0xdffffc000000000a: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000050-0x0000000000000057] CPU: 6 PID: 3486 Comm: kworker/6:0 Not tainted 6.3.0-rc5_for_upstream_debug_2023_04_06_11_01 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: events xfrm_state_gc_task RIP: 0010:mlx5e_xfrm_free_state+0x177/0x260 [mlx5_core] Code: c1 ea 03 80 3c 02 00 0f 85 f5 00 00 00 4c 8b a5 08 01 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d 7c 24 50 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 b7 00 00 00 49 8b 7c 24 50 e8 85 7c 09 e0 4c 89 RSP: 0018:ffff888137a8fc50 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: ffff888180398000 RCX: 0000000000000000 RDX: 000000000000000a RSI: ffffffffa1878227 RDI: 0000000000000050 RBP: ffff88812a0c8000 R08: ffff888137a8fb60 R09: 0000000000000000 R10: fffffbfff09aba0c R11: 0000000000000001 R12: 0000000000000000 R13: ffff88812a0c8108 R14: ffffffff84c63480 R15: ffff8881acb63118 FS: 0000000000000000(0000) GS:ffff88881eb00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f667e8bc000 CR3: 0000000004693006 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ___xfrm_state_destroy+0x3c8/0x5e0 xfrm_state_gc_task+0xf6/0x140 ? ___xfrm_state_destroy+0x5e0/0x5e0 process_one_work+0x7c2/0x1340 ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0 ? pwq_dec_nr_in_flight+0x230/0x230 ? spin_bug+0x1d0/0x1d0 worker_thread+0x59d/0xec0 ? __kthread_parkme+0xd9/0x1d0 ? process_one_work+0x1340/0x1340 kthread+0x28f/0x330 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 Modules linked in: sch_ingress openvswitch nsh mlx5_vdpa vringh vhost_iotlb vdpa mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_umad ib_ipoib ib_cm ib_uverbs ib_core vfio_pci vfio_pci_core vfio_iommu_type1 vfio cuse overlay zram zsmalloc fuse [last unloaded: mlx5_core] ---[ end trace 0000000000000000 ]--- Fixes: 4562116f ("net/mlx5e: Generalize IPsec work structs") Signed-off-by:
-
Leon Romanovsky authored
Fix size argument in memcmp to compare whole IPv6 address. Fixes: b3beba1f ("net/mlx5e: Allow policies with reqid 0, to support IKE policy holes") Reviewed-by:
Raed Salem <raeds@nvidia.com> Reviewed-by:
Emeel Hakim <ehakim@nvidia.com> Signed-off-by:
-
Leon Romanovsky authored
Addition of new err_xfrm label caused to error messages be overwritten. Fix it by using proper NL_SET_ERR_MSG_WEAK_MOD macro together with change in a default message. Fixes: aa8bd0c9 ("net/mlx5e: Support IPsec acquire default SA") Reviewed-by:
-
Leon Romanovsky authored
When trying to set IPsec policy block action the following error is generated: mlx5_cmd_out_err:803:(pid 3426): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3), err(-22) This error means that drop action is not allowed when modify action is set, so update the code to skip modify header for XFRM_POLICY_BLOCK action. Fixes: 67212396 ("net/mlx5e: Skip IPsec encryption for TX path without matching policy") Signed-off-by:
-
Yan Wang authored
The system hang because of dsa_tag_8021q_port_setup()-> stmmac_vlan_rx_add_vid(). I found in stmmac_drv_probe() that cailing pm_runtime_put() disabled the clock. First, when the kernel is compiled with CONFIG_PM=y,The stmmac's resume/suspend is active. Secondly,stmmac as DSA master,the dsa_tag_8021q_port_setup() function will callback stmmac_vlan_rx_add_vid when DSA dirver starts. However, The system is hanged for the stmmac_vlan_rx_add_vid() accesses its registers after stmmac's clock is closed. I would suggest adding the pm_runtime_resume_and_get() to the stmmac_vlan_rx_add_vid().This guarantees that resuming clock output while in use. Fixes: b3dcb312 ("net: stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()") Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
Yan Wang <rk.code@outlook.com> Signed-off-by:
-
David S. Miller authored
Shannon Nelson says: ==================== pds_core driver Summary: -------- This patchset implements a new driver for use with the AMD/Pensando Distributed Services Card (DSC), intended to provide core configuration services through the auxiliary_bus and through a couple of EXPORTed functions for use initially in VFio and vDPA feature specific drivers. To keep this patchset to a manageable size, the pds_vdpa and pds_vfio drivers have been split out into their own patchsets to be reviewed separately. Detail: ------- AMD/Pensando is making available a new set of devices for supporting vDPA, VFio, and potentially other features in the Distributed Services Card (DSC). These features are implemented through a PF that serves as a Core device for controlling and configuring its VF devices. These VF devices have separate drivers that use the auxiliary_bus to work through the Core device as the control path. Currently, the DSC supports standard ethernet operations using the ionic driver. This is not replaced by the Core-based devices - these new devices are in addition to the existing Ethernet device. Typical DSC configurations will include both PDS devices and Ionic Eth devices. However, there is a potential future path for ethernet services to come through this device as well. The Core device is a new PCI PF/VF device managed by a new driver 'pds_core'. The PF device has access to an admin queue for configuring the services used by the VFs, and sets up auxiliary_bus devices for each vDPA VF for communicating with the drivers for the vDPA devices. The VFs may be for VFio or vDPA, and other services in the future; these VF types are selected as part of the DSC internal FW configurations, which is out of the scope of this patchset. When the vDPA support set is enabled in the core PF through its devlink param, auxiliary_bus devices are created for each VF that supports the feature. The vDPA driver then connects to and uses this auxiliary_device to do control path configuration through the PF device. This can then be used with the vdpa kernel module to provide devices for virtio_vdpa kernel module for host interfaces, or vhost_vdpa kernel module for interfaces exported into your favorite VM. A cheap ASCII diagram of a vDPA instance looks something like this: ,----------. | vdpa | '----------' | || ctl data | || .----------. || | pds_vdpa | || '----------' || | || pds_core.vDPA.1 || | || .---------------. || | pds_core | || '---------------' || || || || 09:00.0 09:00.1 == PCI ============================================ || || .----------. .----------. ,------| PF |---| VF |-------, | '----------' '----------' | | DSC | | | ------------------------------------------ Changes: v11: - change strncpy to strscpy Reported-by:kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202304181137.WaZTYyAa-lkp@intel.com/ v10: Link: https://lore.kernel.org/netdev/20230418003228.28234-1-shannon.nelson@amd.com/ - remove CONFIG_DEBUG_FS guard static inline stuff - remove unnecessary 0 and null initializations - verify in driver load that PDS_CORE_DRV_NAME matches KBUILD_MODNAME - remove debugfs irqs_show(), redundant with /proc - return -ENOMEM if intr_info = kcalloc() fails - move the status code enum into pds_core_if.h as part of API definition - fix up one place in pdsc_devcmd_wait() we're using the status codes where we could use the errno - remove redundant calls to flush_workqueue() - grab config_lock before testing state bits in pdsc_fw_reporter_diagnose() - change pdsc_color_match() to return bool - remove useless VIF setup loop and just setup vDPA services for now - remove pf pointer from struct padev and have clients use pci_physfn() - drop use of "vf" in auxdev.c function names, make more generic - remove last of client ops struct and simply export the functions - drop drivers@pensando.io from MAINTAINERS and add new include dir - include dynamic_debug.h in adminq.c to protect dynamic_hex_dump() - fixed fw_slot type from u8 to int for handling error returns - fixed comment spelling - changed void arg in pdsc_adminq_post() to struct pdsc * v9: Link: https://lore.kernel.org/netdev/20230406234143.11318-1-shannon.nelson@amd.com/ - change pdsc field name id to uid to clarify the unique id used for aux device - remove unnecessary pf->state and other checks in aux device creation - hardcode fw slotnames for devlink info, don't use strings from FW - handle errors from PDS_CORE_CMD_INIT devcmd call - tighten up health thread use of config_lock - remove pdsc_queue_health_check() layer over queuing health check - start pds_core.rst file in first patch, add to it incrementally - give more user interaction info in commit messages - removed a few more extraneous includes v8: Link: https://lore.kernel.org/netdev/20230330234628.14627-1-shannon.nelson@amd.com/ - fixed deadlock problem, use devl_health_reporter_destroy() when devlink is locked - don't clear client_id until after auxiliary_device_uninit() v7: Link: https://lore.kernel.org/netdev/20230330192313.62018-1-shannon.nelson@amd.com/ - use explicit devlink locking and devl_* APIs - move some of devlink setup logic into probe and remove - use debugfs_create_u{type}() for state and queue head and tail - add include for linux/vmalloc.h Reported-by:
-
Shannon Nelson authored
Remaining documentation and Kconfig hook for building the driver. Signed-off-by:
Shannon Nelson <shannon.nelson@amd.com> Acked-by:
-
Shannon Nelson authored
When the Core device gets an event from the device, or notices the device FW to be up or down, it needs to send those events on to the clients that have an event handler. Add the code to pass along the events to the clients. The entry points pdsc_register_notify() and pdsc_unregister_notify() are EXPORTed for other drivers that want to listen for these events. Signed-off-by:
-
Shannon Nelson authored
Add the client API operations for running adminq commands. The core registers the client with the FW, then the client has a context for requesting adminq services. We expect to add additional operations for other clients, including requesting additional private adminqs and IRQs, but don't have the need yet. Signed-off-by:
-
Shannon Nelson authored
Add the devlink parameter switches so the user can enable the features supported by the VFs. The only feature supported at the moment is vDPA. Example: devlink dev param set pci/0000:2b:00.0 \ name enable_vnet cmode runtime value true Signed-off-by: -
Shannon Nelson authored
An auxiliary_bus device is created for each vDPA type VF at VF probe and destroyed at VF remove. The aux device name comes from the driver name + VIF type + the unique id assigned at PCI probe. The VFs are always removed on PF remove, so there should be no issues with VFs trying to access missing PF structures. The auxiliary_device names will look like "pds_core.vDPA.nn" where 'nn' is the VF's uid. Signed-off-by:
-
Shannon Nelson authored
This is the initial VF PCI driver framework for the new pds_vdpa VF device, which will work in conjunction with an auxiliary_bus client of the pds_core driver. This does the very basics of registering for the new VF device, setting up debugfs entries, and registering with devlink. Signed-off-by:
-
Shannon Nelson authored
The Virtual Interfaces (VIFs) supported by the DSC's configuration (vDPA, Eth, RDMA, etc) are reported in the dev_ident struct and made visible in debugfs. At this point only vDPA is supported in this driver so we only setup devices for that feature. Signed-off-by:
-
Shannon Nelson authored
Add in the support for doing firmware updates. Of the two main banks available, a and b, this updates the one not in use and then selects it for the next boot. Example: devlink dev flash pci/0000:b2:00.0 \ file pensando/dsc_fw_1.63.0-22.tar Signed-off-by: -
Shannon Nelson authored
Add the service routines for submitting and processing the adminq messages and for handling notifyq events. Signed-off-by:
-
Shannon Nelson authored
Set up the basic adminq and notifyq queue structures. These are used mostly by the client drivers for feature configuration. These are essentially the same adminq and notifyq as in the ionic driver. Part of this includes querying for device identity and FW information, so we can make that available to devlink dev info. $ devlink dev info pci/0000:b5:00.0 pci/0000:b5:00.0: driver pds_core serial_number FLM18420073 versions: fixed: asic.id 0x0 asic.rev 0x0 running: fw 1.51.0-73 stored: fw.goldfw 1.15.9-C-22 fw.mainfwa 1.60.0-73 fw.mainfwb 1.60.0-57 Signed-off-by: -
Shannon Nelson authored
Add devlink health reporting on top of our fw watchdog. Example: # devlink health show pci/0000:2b:00.0 reporter fw pci/0000:2b:00.0: reporter fw state healthy error 0 recover 0 # devlink health diagnose pci/0000:2b:00.0 reporter fw Status: healthy State: 1 Generation: 0 Recoveries: 0 Signed-off-by: -
Shannon Nelson authored
Add in the periodic health check and the related workqueue, as well as the handlers for when a FW reset is seen. The firmware is polled every 5 seconds to be sure that it is still alive and that the FW generation didn't change. The alive check looks to see that the PCI bus is still readable and the fw_status still has the RUNNING bit on. If not alive, the driver stops activity and tears things down. When the FW recovers and the alive check again succeeds, the driver sets back up for activity. The generation check looks at the fw_generation to see if it has changed, which can happen if the FW crashed and recovered or was updated in between health checks. If changed, the driver counts that as though the alive test failed and forces the fw_down/fw_up cycle. Signed-off-by:
-
Shannon Nelson authored
The devcmd interface is the basic connection to the device through the PCI BAR for low level identification and command services. This does the early device initialization and finds the identity data, and adds devcmd routines to be used by later driver bits. Signed-off-by:
-
Shannon Nelson authored
This is the initial PCI driver framework for the new pds_core device driver and its family of devices. This does the very basics of registering for the new PF PCI device 1dd8:100c, setting up debugfs entries, and registering with devlink. Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== bridge: Add per-{Port, VLAN} neighbor suppression Background ========== In order to minimize the flooding of ARP and ND messages in the VXLAN network, EVPN includes provisions [1] that allow participating VTEPs to suppress such messages in case they know the MAC-IP binding and can reply on behalf of the remote host. In Linux, the above is implemented in the bridge driver using a per-port option called "neigh_suppress" that was added in kernel version 4.15 [2]. Motivation ========== Some applications use ARP messages as keepalives between the application nodes in the network. This works perfectly well when two nodes are connected to the same VTEP. When a node goes down it will stop responding to ARP requests and the other node will notice it immediately. However, when the two nodes are connected to different VTEPs and neighbor suppression is enabled, the local VTEP will reply to ARP requests even after the remote node went down, until certain timers expire and the EVPN control plane decides to withdraw the MAC/IP Advertisement route for the address. Therefore, some users would like to be able to disable neighbor suppression on VLANs where such applications reside and keep it enabled on the rest. Implementation ============== The proposed solution is to allow user space to control neighbor suppression on a per-{Port, VLAN} basis, in a similar fashion to other per-port options that gained per-{Port, VLAN} counterparts such as "mcast_router". This allows users to benefit from the operational simplicity and scalability associated with shared VXLAN devices (i.e., external / collect-metadata mode), while still allowing for per-VLAN/VNI neighbor suppression control. The user interface is extended with a new "neigh_vlan_suppress" bridge port option that allows user space to enable per-{Port, VLAN} neighbor suppression on the bridge port. When enabled, the existing "neigh_suppress" option has no effect and neighbor suppression is controlled using a new "neigh_suppress" VLAN option. Example usage: # bridge link set dev vxlan0 neigh_vlan_suppress on # bridge vlan add vid 10 dev vxlan0 # bridge vlan set vid 10 dev vxlan0 neigh_suppress on Testing ======= Tested using existing bridge selftests. Added a dedicated selftest in the last patch. Patchset overview ================= Patches #1-#5 are preparations. Patch #6 adds per-{Port, VLAN} neighbor suppression support to the bridge's data path. Patches #7-#8 add the required netlink attributes to enable the feature. Patch #9 adds a selftest. iproute2 patches can be found here [3]. Changelog ========= Since RFC [4]: No changes. [1] https://www.rfc-editor.org/rfc/rfc7432#section-10 [2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a42317785c898c0ed46db45a33b0cc71b671bf29 [3] https://github.com/idosch/iproute2/tree/submit/neigh_suppress_v1 [4] https://lore.kernel.org/netdev/20230413095830.2182382-1-idosch@nvidia.com/ ==================== Signed-off-by: -
Ido Schimmel authored
Add test cases for bridge neighbor suppression, testing both per-port and per-{Port, VLAN} neighbor suppression with both ARP and NS packets. Example truncated output: # ./test_bridge_neigh_suppress.sh [...] Tests passed: 148 Tests failed: 0 Signed-off-by:Ido Schimmel <idosch@nvidia.com> Acked-by:
Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by:
-
Ido Schimmel authored
Add a new bridge port attribute that allows user space to enable per-{Port, VLAN} neighbor suppression. Example: # bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]' false # bridge link set dev swp1 neigh_vlan_suppress on # bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]' true # bridge link set dev swp1 neigh_vlan_suppress off # bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]' false Signed-off-by: -
Ido Schimmel authored
Add a new VLAN attribute that allows user space to set the neighbor suppression state of the port VLAN. Example: # bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]' false # bridge vlan set vid 10 dev swp1 neigh_suppress on # bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]' true # bridge vlan set vid 10 dev swp1 neigh_suppress off # bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]' false # bridge vlan set vid 10 dev br0 neigh_suppress on Error: bridge: Can't set neigh_suppress for non-port vlans. Signed-off-by:
-
Ido Schimmel authored
When the bridge is not VLAN-aware (i.e., VLAN ID is 0), determine if neighbor suppression is enabled on a given bridge port solely based on the existing 'BR_NEIGH_SUPPRESS' flag. Otherwise, if the bridge is VLAN-aware, first check if per-{Port, VLAN} neighbor suppression is enabled on the given bridge port using the 'BR_NEIGH_VLAN_SUPPRESS' flag. If so, look up the VLAN and check whether it has neighbor suppression enabled based on the per-VLAN 'BR_VLFLAG_NEIGH_SUPPRESS_ENABLED' flag. If the bridge is VLAN-aware, but the bridge port does not have per-{Port, VLAN} neighbor suppression enabled, then fallback to determine neighbor suppression based on the 'BR_NEIGH_SUPPRESS' flag. Signed-off-by: -
Ido Schimmel authored
Currently, there are various places in the bridge data path that check whether neighbor suppression is enabled on a given bridge port. As a preparation for per-{Port, VLAN} neighbor suppression, encapsulate this logic in a function and pass the VLAN ID of the packet as an argument. Signed-off-by: -
Ido Schimmel authored
The bridge driver gates the neighbor suppression code behind an internal per-bridge flag called 'BROPT_NEIGH_SUPPRESS_ENABLED'. The flag is set when at least one bridge port has neighbor suppression enabled. As a preparation for per-{Port, VLAN} neighbor suppression, make sure the global flag is also set if per-{Port, VLAN} neighbor suppression is enabled. That is, when the 'BR_NEIGH_VLAN_SUPPRESS' flag is set on at least one bridge port. Signed-off-by: -
Ido Schimmel authored
Add two internal flags that will be used to enable / disable per-{Port, VLAN} neighbor suppression: 1. 'BR_NEIGH_VLAN_SUPPRESS': A per-port flag used to indicate that per-{Port, VLAN} neighbor suppression is enabled on the bridge port. When set, 'BR_NEIGH_SUPPRESS' has no effect. 2. 'BR_VLFLAG_NEIGH_SUPPRESS_ENABLED': A per-VLAN flag used to indicate that neighbor suppression is enabled on the given VLAN. Signed-off-by: -
Ido Schimmel authored
Subsequent patches are going to add per-{Port, VLAN} neighbor suppression, which will require br_flood() to potentially suppress ARP / NS packets on a per-{Port, VLAN} basis. As a preparation, pass the VLAN ID of the packet as another argument to br_flood(). Signed-off-by: -
Ido Schimmel authored
The bridge does not flood ARP / NS packets for which a reply was sent to bridge ports that have neighbor suppression enabled. Subsequent patches are going to add per-{Port, VLAN} neighbor suppression, which is going to make it more expensive to check whether neighbor suppression is enabled since a VLAN lookup will be required. Therefore, instead of unnecessarily performing this lookup for every packet, only perform it for ARP / NS packets for which a reply was sent. Signed-off-by: -
David S. Miller authored
Emeel Hakim says: ==================== Support MACsec VLAN This patch series introduces support for hardware (HW) offload MACsec devices with VLAN configuration. The patches address both scenarios where the VLAN header is both the inner and outer header for MACsec. The changes include: 1. Adding MACsec offload operation for VLAN. 2. Considering VLAN when accessing MACsec net device. 3. Currently offloading MACsec when it's configured over VLAN with current MACsec TX steering rules would wrongly insert the MACsec sec tag after inserting the VLAN header. This resulted in an ETHERNET | SECTAG | VLAN packet when ETHERNET | VLAN | SECTAG is configured. The patche handles this issue when configuring steering rules. 4. Adding MACsec rx_handler change support in case of a marked skb and a mismatch on the dst MAC address. Please review these changes and let me know if you have any feedback or concerns. Updates since v1: - Consult vlan_features when adding NETIF_F_HW_MACSEC. - Allow grep for the functions. - Add helper function to get the macsec operation to allow the compiler to make some choice. Updates since v2: - Don't use macros to allow direct navigattion from mdo functions to its implementation. - Make the vlan_get_macsec_ops argument a const. - Check if the specific mdo function is available before calling it. - Enable NETIF_F_HW_MACSEC by default when the lower device has it enabled and in case the lower device currently has NETIF_F_HW_MACSEC but disabled let the new vlan device also have it disabled. Updates since v3: - Split patch ("vlan: Add MACsec offload operations for VLAN interface") to prevent mixing generic vlan code changes with driver changes. - Add mdo_open, stop and stats to support drivers which have those. - Don't fail if macsec offload operations are available but a specific function is not, to support drivers which does not implement all macsec offload operations. - Don't call find_rx_sc twice in the same loop, instead save the result in a parameter and re-use it. - Completely remove _BUILD_VLAN_MACSEC_MDO macro, to prevent returning from a macro. - Reorder the functions inside struct macsec_ops to match the struct decleration. Updates since v4: - Change subject line of ("macsec: Add MACsec rx_handler change support") and adapt commit message. - Don't separate the new check in patch ("macsec: Add MACsec rx_handler change support") from the previous if/else if. - Drop"_found" from the parameter naming "rx_sc_found" and move the definition to the relevant block. - Remove "{}" since not needed around a single line. Updates since v5: - Consider promiscuous mode case. Updates since v6: - Use IS_ENABLED instead of checking for ifdef. - Don't add inline keywork in c files, let the compiler make its own decisions. ==================== Signed-off-by: -
Emeel Hakim authored
Offloading device drivers will mark offloaded MACsec SKBs with the corresponding SCI in the skb_metadata_dst so the macsec rx handler will know to which interface to divert those skbs, in case of a marked skb and a mismatch on the dst MAC address, divert the skb to the macsec net_device where the macsec rx_handler will be called to consider cases where relying solely on the dst MAC address is insufficient. One such instance is when using MACsec with a VLAN as an inner header, where the packet structure is ETHERNET | SECTAG | VLAN. In such a scenario, the dst MAC address in the ethernet header will correspond to the VLAN MAC address, resulting in a mismatch. Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by:
-
Emeel Hakim authored
Offloading MACsec when its configured over VLAN with current MACsec TX steering rules will wrongly insert MACsec sec tag after inserting the VLAN header leading to a ETHERNET | SECTAG | VLAN packet when ETHERNET | VLAN | SECTAG is configured. The above issue is due to adding the SECTAG by HW which is a later stage compared to the VLAN header insertion stage. Detect such a case and adjust TX steering rules to insert the SECTAG in the correct place by using reformat_param_0 field in the packet reformat to indicate the offset of SECTAG from end of the MAC header to account for VLANs in granularity of 4Bytes. Signed-off-by:
-
Emeel Hakim authored
MACsec device may have a VLAN device on top of it. Detect MACsec state correctly under this condition, and return the correct net device accordingly. Signed-off-by:
-
Emeel Hakim authored
Enable MACsec offload feature over VLAN by adding NETIF_F_HW_MACSEC to the device vlan_features. Signed-off-by:
-
