[why]
A few of the new DSC DPCD caps were introduced by a DP 1.4a SCR in order
to give DSC branch decoders a chance to expose their maximum throughput
and maximum line width limitations.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
If a set is done, DSC settings are zeroed out, leading to no DSC for the modes
that require ODM, such as 8k60.

This was a regression introduced by 5a4f26295176bbfc776c75aaf0f6dd8ccf806958.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
Gamut map lib provides a wider gamut mapping options
vs BT2390
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Emulating passive dongle on USB-C port causes issue on some asics.

[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The DCHub arbiter has a mechanism to dynamically rate limit the DCHub
request stream to the fabric. If the memory controller is fully utilized
and the DCHub requestors are well ahead of their amortized schedule,
then it is safe to prevent the next winner from being committed and sent
to the fabric. The utilization of the memory controller is approximated
by ensuring that the number of outstanding requests is greater than a
threshold specified by the ARB_MIN_REQ_OUTSTANDING. To determine that
the DCHub requestors are well ahead of the amortized schedule, the slack
of the next winner is compared with the ARB_SAT_LEVEL in DLG RefClk
cycles.

[How]
The recommended settings to enable thise dynamic limiting for Navi is
180 requests.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
It was missing, although defined in DP spec

[how]
- Add handling of this value to DSC code
- Also remove unused file dsc_helpers.c
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
This is for DC_I2c arbitration use between HW use/SW use and DMCU use.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
'Divide by zero' error happens when line size happens to be zero.

[how]
The code that makes sure line size minimum value can be 1 was already
present in DCN1 part of the driver, this is mearly a port to DCN2.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In order to ensure that incoming flips are latched and
complete immediately, we need to program the vupdate
interrupt to come during the back porch of each frame.

[How]
Program the vupdate start_line to be in the back porch
like it's done for DCN1.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Refactor programming watermark function:
Divided into urgent watermark, stutter watermark and pstate watermark.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The split condition is broken and will always activate
at the moment.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1 and DCN2.

In addition, future HW will need to access the HUBPREQ_DEBUG and
CUR_TTU_CNTL0 register for hubp_init. Add that here.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
OPTC data format was left at its default value (444) when enabling
ODM combine. This caused issues with FPGA capture.

[How]
Write the OPTC_DATA_FORMAT field when enabling ODM combine.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Due to the generic introduction of seamless boot, the display is no
longer blanked upon boot. However, this causes corruption on some
systems that does not lock the memory in the non-secure boot case,
resulting in brief corruption on boot due to garbage being written into
the frame buffer.

[How]
Add a flag, read during DC init, to determine whether display should be
blanked on boot. Default to true.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
DSC target bpp precision is a decoder DPCD and an AMD encoder capability.
It must be taken into account when calculating target bitrate.

[how]
Add a DC DSC function that does this calculation.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
ABM is currently not enabled on DCN2.

[How]
Update the register name list for DCN2 and un-comment the code that
creates the abm object.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
The current policy will always enable DSC to 12 bpp
regardless of if the current bandwidth is enough for MST displays.
This logic is not optimal because user will get lower quality output
if DSC compression is enabled.
This change to is to implement a DSC MST bandwidth fair share
algorithm so we will dynamically decide if DSC is needed and what
quality (target bpp) is needed to fairly destribute the MST bandwidth
in one MST topology. This will allow user to see the most optimal
image quality with the given bandwidth.

[how]
We will start with lowest bandwidth possible and run a
Max-Min fairness algorithm to fairly distribute the available
bandwidth. If there is still remaining bandwidth, we will try to fit
the timing without DSC compression.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
There are ASICs that have fewer DSC engines than pipes, which makes
DSC a resource that should be used only if required.

[how]
Acquire DSC HW resource if required by stream and release when not
required anymore.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY] system crash when initialize dwb
current linux driver does not support dwb.
 disable this feature for now.

[HOW] set num_dwb = 0 to disable dwb for now
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY] linux upstream already has interrupt vupdate for freesync
in dcn10. dcn20 interrupt shares the same source code as dcn10.
but dcn20 interrupt translator does not add vupdate interrupt.
this cause index of vupdate aarray be negative which causes
crash.

[HOW] add vupdate into dc interrupt transltor
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
DSC resource has to be acquired before it can be used and simply copying
a reference to it is very likely to cause problems when accessing DSC.

[how]
Set DSC resource pointer to NULL to mark it as unused after primary pipe
resources were copied to the secondary ODM pipe.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Some nightly tests are failing since the new value for fclk is a
bit too low. Also, a new test for the maximum downscale case was
needed.

[How]
Updated the default value for fclk to be 1.2GHz.
Signed-off-by: Tyler DiBattista <tyler.dibattista@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
when an update programming sequence requires both
front end and back end pipe to be updated synchronously,
a global update lock needs to be set to ensure that
we don't get a frame with only front end update but
not the back end update.

[how]
setup global lock parameters on enable_stream_timing.
enable global lock when pipe_control_lock_global is called.
disable global lock when pipe_control_lock is called.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Some register fields are not needed.

[How]
remove them
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We used this change to investigate the performance of bandwidth validation,
it will be useful to have if we need to investigate further.

[How]
We use performance counter tick numbers to profile performance, they live
at dc->debug.bw_val_profile (set .enable in debugger to turn on measuring).
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We can split validation into three parts: getting voltage level, getting
watermarks, and rq/dlg calculations. The voltage level is enough to answer
the question "do we support this state", and the rest of it is to determine
what hardware programming is needed to support the state. Most of the calls
to validate_bandwidth only care about the first part, so we added an early
return in that case
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]

display_mode_vba is for DCN2 and up. When building for upstream (DCN1
enabled only), there will be a build error, since display_mode_vba.c/h
is stripped out.

Note that building DCN1 only with internal dal-dev is still fine, since
display_mode_vba.h is not stripped out internally - only in upstream.
The make directives therefore stll work, and so will any #include's.

[How]

Since subsequent generations require DCN2 enabled anyways, guard the
makefile directive for display_mode_vba.o with DCN2. Guard any includes
with DCN2. In addition, guard the entire contents of display_mode_vba.h
with DCN2, to simulate the file being stripped out in upstream.

A forward declaration for 'struct display_mode_lib' also needs to be
added in display_mode_lib.h. Previously, display_mode_vba.h contained
the forward declaration, and display_mode_lib.h in turn included it.
This won't work if mode_vba.h is stripped out, requring mode_lib.h to do
so itself.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Usage of this enum is DSC-only.

[How]
Guard it with CONFIG_DRM_AMD_DC_DSC_SUPPORT.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
The follow up change
Improve some naming for fields and structs
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Can not turn on two displays at the same time with the asic having only one DSC.
DC_DSC_RESOURCE allocation failed.

[Solution]
Only add_dsc if the timing is dsc capable based on diag_dc and num_dsc
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
If voltage level > 0, DCFCLK and SOCCLK could be 0 during DML
calculations, which ended up causing an assert.

[How]
Initialize dcfclk_mhz and socclk_mhz values according to the
voltage level.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Added some regs and exposed some functions for future use
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Move flags from color_gamma.h to mod_shared.h
and add more options and setting structures
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why] DSC spec requires this
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
On at least some of the devices (e.g. Realtek scaler) we get a black screen if 1/16th
precision is used.

[how]
Work around it by reducing precision to 1/8th for N4:2:2 and 4:2:0 color formats. This
is a safe workaround and would have a very mild impact on the quality.
The issue is still to be root-caused and fixed correctly.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Global optic double buffer lock is currently disabled due to
incorrect programming sequence that affects non global lock.

[how]
Isolate global lock programming sequence out of non global lock
programming sequence, so it can be enabled without affecting
non global lock.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
This is now done in the original link bandwidth calculation and DSC
must not do this anymore.

[how]
Remove the line of code that should have been removed when transition
to correctly applying FEC overhead was made.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

code restructure.
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We shouldnt need overhead on top of dppclk when setting fclk.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>