Merge tag 'linux-can-fixes-for-5.12-20210329' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2021-03-29

this is a pull request of 3 patches for net/master.

The two patch are by Oliver Hartkopp. He fixes length check in the
proto_ops::getname callback for the CAN RAW, BCM and ISOTP protocols,
which were broken by the introduction of the J1939 protocol.

The last patch is by me and fixes the a BUILD_BUG_ON() check which
triggers on ARCH=arm with CONFIG_AEABI unset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum: Fix ECN marking in tunnel decapsulation

Patch #1 fixes a discrepancy between the software and hardware data
paths with regards to ECN marking after decapsulation. See the changelog
for a detailed description.

Patch #2 extends the ECN decap test to cover all possible combinations
of inner and outer ECN markings. The test passes over both data paths.

v2:
* Only set ECT(1) if inner is ECT(0)
* Introduce a new helper to determine inner ECN. Share it between NVE
  and IP-in-IP tunnels
* Extend the selftest
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that all possible combinations of inner and outer ECN bits result
in the correct inner ECN marking according to RFC 6040 4.2.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cited commit changed the behavior of the software data path with regards
to the ECN marking of decapsulated packets. However, the commit did not
change other callers of __INET_ECN_decapsulate(), namely mlxsw. The
driver is using the function in order to ensure that the hardware and
software data paths act the same with regards to the ECN marking of
decapsulated packets.

The discrepancy was uncovered by commit 5aa3c334 ("selftests:
forwarding: vxlan_bridge_1d: Fix vxlan ecn decapsulate value") that
aligned the selftest to the new behavior. Without this patch the
selftest passes when used with veth pairs, but fails when used with
mlxsw netdevs.

Fix this by instructing the device to propagate the ECT(1) mark from the
outer header to the inner header when the inner header is ECT(0), for
both NVE and IP-in-IP tunnels.

A helper is added in order not to duplicate the code between both tunnel
types.

Fixes: b7237487 ("tunnel: Propagate ECT(1) when decapsulating as recommended by RFC6040")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit ea780056 ("can: add optional DLC element to Classical
CAN frame structure") the struct can_frame::can_dlc was put into an
anonymous union with another u8 variable.

For various reasons some members in struct can_frame and canfd_frame
including the first 8 byes of data are expected to have the same
memory layout. This is enforced by a BUILD_BUG_ON check in af_can.c.

Since the above mentioned commit this check fails on ARM kernels
compiled with the ARM OABI (which means CONFIG_AEABI not set). In this
case -mabi=apcs-gnu is passed to the compiler, which leads to a
structure size boundary of 32, instead of 8 compared to CONFIG_AEABI
enabled. This means the the union in struct can_frame takes 4 bytes
instead of the expected 1.

Rong Chen illustrates the problem with pahole in the ARM OABI case:

| struct can_frame {
|          canid_t                    can_id;               /* 0     4 */
|          union {
|                  __u8               len;                  /* 4     1 */
|                  __u8               can_dlc;              /* 4     1 */
|          };                                               /* 4     4 */
|          __u8                       __pad;                /* 8     1 */
|          __u8                       __res0;               /* 9     1 */
|          __u8                       len8_dlc;             /* 10    1 */
|
|          /* XXX 5 bytes hole, try to pack */
|
|          __u8                       data[8]
| __attribute__((__aligned__(8))); /*    16     8 */
|
|          /* size: 24, cachelines: 1, members: 6 */
|          /* sum members: 19, holes: 1, sum holes: 5 */
|          /* forced alignments: 1, forced holes: 1, sum forced holes: 5 */
|          /* last cacheline: 24 bytes */
| } __attribute__((__aligned__(8)));

Marking the anonymous union as __attribute__((packed)) fixes the
BUILD_BUG_ON problem on these compilers.

Fixes: ea780056 ("can: add optional DLC element to Classical CAN frame structure")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Rong Chen <rong.a.chen@intel.com>
Link: https://lore.kernel.org/linux-can/2c82ec23-3551-61b5-1bd8-178c3407ee83@hartkopp.net/
Link: https://lore.kernel.org/r/20210325125850.1620-3-socketcan@hartkopp.netSigned-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit f5223e9e ("can: extend sockaddr_can to include j1939
members") the sockaddr_can has been extended in size and a new
CAN_REQUIRED_SIZE macro has been introduced to calculate the protocol
specific needed size.

The ABI for the msg_name and msg_namelen has not been adapted to the
new CAN_REQUIRED_SIZE macro for the other CAN protocols which leads to
a problem when an existing binary reads the (increased) struct
sockaddr_can in msg_name.

Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol")
Reported-by: Richard Weinberger <richard@nod.at>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Link: https://lore.kernel.org/linux-can/1135648123.112255.1616613706554.JavaMail.zimbra@nod.at/T/#t
Link: https://lore.kernel.org/r/20210325125850.1620-2-socketcan@hartkopp.netSigned-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit f5223e9e ("can: extend sockaddr_can to include j1939
members") the sockaddr_can has been extended in size and a new
CAN_REQUIRED_SIZE macro has been introduced to calculate the protocol
specific needed size.

The ABI for the msg_name and msg_namelen has not been adapted to the
new CAN_REQUIRED_SIZE macro for the other CAN protocols which leads to
a problem when an existing binary reads the (increased) struct
sockaddr_can in msg_name.

Fixes: f5223e9e ("can: extend sockaddr_can to include j1939 members")
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Link: https://lore.kernel.org/linux-can/1135648123.112255.1616613706554.JavaMail.zimbra@nod.at/T/#t
Link: https://lore.kernel.org/r/20210325125850.1620-1-socketcan@hartkopp.netSigned-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In pvc_xmit, if __skb_pad(skb, pad, false) failed, it will free
the skb in the first time and goto drop. But the same skb is freed
by kfree_skb(skb) in the second time in drop.

Maintaining the original function unchanged, my patch adds a new
label out to avoid the double free if __skb_pad() failed.

Fixes: f5083d0c ("drivers/net/wan/hdlc_fr: Improvements to the code of pvc_xmit")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-03-25

This series contains updates to virtchnl header file and i40e driver.

Norbert removes added padding from virtchnl RSS structures as this
causes issues when iterating over the arrays.

Mateusz adds Asym_Pause as supported to allow these settings to be set
as the hardware supports it.

Eryk fixes an issue where encountering a VF reset alongside releasing
VFs could cause a call trace.

Arkadiusz moves TC setup before resource setup as previously it was
possible to enter with a null q_vector causing a kernel oops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes following syzbot report:

UBSAN: shift-out-of-bounds in ./include/net/red.h:237:23
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 1 PID: 8418 Comm: syz-executor170 Not tainted 5.12.0-rc4-next-20210324-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:79 [inline]
 dump_stack+0x141/0x1d7 lib/dump_stack.c:120
 ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
 __ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:327
 red_set_parms include/net/red.h:237 [inline]
 choke_change.cold+0x3c/0xc8 net/sched/sch_choke.c:414
 qdisc_create+0x475/0x12f0 net/sched/sch_api.c:1247
 tc_modify_qdisc+0x4c8/0x1a50 net/sched/sch_api.c:1663
 rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5553
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x43f039
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffdfa725168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000400488 RCX: 000000000043f039
RDX: 0000000000000000 RSI: 0000000020000040 RDI: 0000000000000004
RBP: 0000000000403020 R08: 0000000000400488 R09: 0000000000400488
R10: 0000000000400488 R11: 0000000000000246 R12: 00000000004030b0
R13: 0000000000000000 R14: 00000000004ac018 R15: 0000000000400488

Fixes: 8afa10cb ("net_sched: red: Avoid illegal values")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: do not modify the shared tunnel info when PMTU triggers an ICMP reply

The series fixes an issue were a shared ip_tunnel_info is modified when
PMTU triggers an ICMP reply in vxlan and geneve, making following
packets in that flow to have a wrong destination address if the flow
isn't updated. A detailled information is given in each of the two
commits.

This was tested manually with OVS and I ran the PTMU selftests with
kmemleak enabled (all OK, none was skipped).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the interface is part of a bridge or an Open vSwitch port and a
packet exceed a PMTU estimate, an ICMP reply is sent to the sender. When
using the external mode (collect metadata) the source and destination
addresses are reversed, so that Open vSwitch can match the packet
against an existing (reverse) flow.

But inverting the source and destination addresses in the shared
ip_tunnel_info will make following packets of the flow to use a wrong
destination address (packets will be tunnelled to itself), if the flow
isn't updated. Which happens with Open vSwitch, until the flow times
out.

Fixes this by uncloning the skb's ip_tunnel_info before inverting its
source and destination addresses, so that the modification will only be
made for the PTMU packet, not the following ones.

Fixes: c1a800e8 ("geneve: Support for PMTU discovery on directly bridged links")
Tested-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the interface is part of a bridge or an Open vSwitch port and a
packet exceed a PMTU estimate, an ICMP reply is sent to the sender. When
using the external mode (collect metadata) the source and destination
addresses are reversed, so that Open vSwitch can match the packet
against an existing (reverse) flow.

But inverting the source and destination addresses in the shared
ip_tunnel_info will make following packets of the flow to use a wrong
destination address (packets will be tunnelled to itself), if the flow
isn't updated. Which happens with Open vSwitch, until the flow times
out.

Fixes this by uncloning the skb's ip_tunnel_info before inverting its
source and destination addresses, so that the modification will only be
made for the PTMU packet, not the following ones.

Fixes: fc68c995 ("vxlan: Support for PMTU discovery on directly bridged links")
Tested-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xiaoming Ni says:

====================
nfc: fix Resource leakage and endless loop

fix Resource leakage and endless loop in net/nfc/llcp_sock.c,
 reported by "kiyin(尹亮)".

Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
====================
math: Export mul_u64_u64_div_u64

Fixes: f51d7bf1 ("ptp_qoriq: fix overflow in ptp_qoriq_adjfine() u64 calcalation")
Signed-off-by: David S. Miller <davem@davemloft.net>

When sock_wait_state() returns -EINPROGRESS, "sk->sk_state" is
 LLCP_CONNECTING. In this case, llcp_sock_connect() is repeatedly invoked,
 nfc_llcp_sock_link() will add sk to local->connecting_sockets twice.
 sk->sk_node->next will point to itself, that will make an endless loop
 and hang-up the system.
To fix it, check whether sk->sk_state is LLCP_CONNECTING in
 llcp_sock_connect() to avoid repeated invoking.

Fixes: b4011239 ("NFC: llcp: Fix non blocking sockets connections")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.11
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In llcp_sock_connect(), use kmemdup to allocate memory for
 "llcp_sock->service_name". The memory is not released in the sock_unlink
label of the subsequent failure branch.
As a result, memory leakage occurs.

fix CVE-2020-25672

Fixes: d646960f ("NFC: Initial LLCP support")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.3
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfc_llcp_local_get() is invoked in llcp_sock_connect(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().

fix CVE-2020-25671
Fixes: c7aa1225 ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.6
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfc_llcp_local_get() is invoked in llcp_sock_bind(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().

fix CVE-2020-25670
Fixes: c7aa1225 ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.6
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on the IOMMU configuration, the current cache control settings can
result in possible coherency issues. The hardware team has recommended
new settings for the PCI device path to eliminate the issue.

Fixes: 6f595959 ("amd-xgbe: Adjust register settings to improve performance")
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.

This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct the Micrel phy documentation for the ksz9021 and ksz9031 phys
for how the phy skews are set.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In setups with fixed-link settings there is no mdio node in DTS.
axienet_probe() already handles that gracefully but lp->mii_bus is
then NULL.

Fix code that tries to blindly grab the MDIO lock by introducing two helper
functions that make the locking conditional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA is aware of switches with global VLAN filtering since the blamed
commit, but it makes a bad decision when multiple bridges are spanning
the same switch:

ip link add br0 type bridge vlan_filtering 1
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br0
ip link set swp4 master br1
ip link set swp5 master br1
ip link set swp5 nomaster
ip link set swp4 nomaster
[138665.939930] sja1105 spi0.1: port 3: dsa_core: VLAN filtering is a global setting
[138665.947514] DSA: failed to notify DSA_NOTIFIER_BRIDGE_LEAVE

When all ports leave br1, DSA blindly attempts to disable VLAN filtering
on the switch, ignoring the fact that br0 still exists and is VLAN-aware
too. It fails while doing that.

This patch checks whether any port exists at all and is under a
VLAN-aware bridge.

Fixes: d371b7c9 ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setup TC before the i40e_setup_pf_switch() call.
Memory must be initialized for all the queues
before using its resources.

Previously it could be possible that a call:
xdp_rxq_info_reg(&rx_ring->xdp_rxq, rx_ring->netdev,
rx_ring->queue_index, rx_ring->q_vector->napi.napi_id);
was made with q_vector being null.

Oops could show up with the following sequence:
- no driver loaded
- FW LLDP agent is on (flag disable-fw-lldp:off)
- link is up
- DCB configured with number of Traffic Classes that will not divide
  completely the default number of queues (usually cpu cores)
- driver load
- set private flag: disable-fw-lldp:on

Fixes: 4b208eaa ("i40e: Add init and default config of software based DCB")
Fixes: b02e5a0e ("xsk: Propagate napi_id to XDP socket Rx path")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix the reason of kernel oops when i40e driver removed VFs.
Added new __I40E_VFS_RELEASING state to signalize releasing
process by PF, that it makes possible to exit of reset VF procedure.
Without this patch, it is possible to suspend the VFs reset by
releasing VFs resources procedure. Retrying the reset after the
timeout works on the freed VF memory causing a kernel oops.

Fixes: d43d60e5 ("i40e: ensure reset occurs when disabling VF")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Merge misc fixes from Andrew Morton:
 "14 patches.

  Subsystems affected by this patch series: mm (hugetlb, kasan, gup,
  selftests, z3fold, kfence, memblock, and highmem), squashfs, ia64,
  gcov, and mailmap"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mailmap: update Andrey Konovalov's email address
  mm/highmem: fix CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP
  mm: memblock: fix section mismatch warning again
  kfence: make compatible with kmemleak
  gcov: fix clang-11+ support
  ia64: fix format strings for err_inject
  ia64: mca: allocate early mca with GFP_ATOMIC
  squashfs: fix xattr id and id lookup sanity checks
  squashfs: fix inode lookup sanity checks
  z3fold: prevent reclaim/free race for headless pages
  selftests/vm: fix out-of-tree build
  mm/mmu_notifiers: ensure range_end() is paired with range_start()
  kasan: fix per-page tags for non-page_alloc pages
  hugetlb_cgroup: fix imbalanced css_get and css_put pair for shared mappings

Pull rdma fixes from Jason Gunthorpe:
 "Not much going on, just some small bug fixes:

   - Typo causing a regression in mlx5 devx

   - Regression in the recent hns rework causing the HW to get out of
     sync

   - Long-standing cxgb4 adaptor crash when destroying cm ids"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/cxgb4: Fix adapter LE hash errors while destroying ipv6 listening server
  RDMA/hns: Fix bug during CMDQ initialization
  RDMA/mlx5: Fix typo in destroy_mkey inbox

Pull mfs fix from Lee Jones:
 "Unconstify editable placeholder structures"

* tag 'mfd-fixes-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: intel_quark_i2c_gpio: Revert "Constify static struct resources"

Pull arm64 fixes from Will Deacon:
 "Minor fixes all over, ranging from typos to tests to errata
  workarounds:

   - Fix possible memory hotplug failure with KASLR

   - Fix FFR value in SVE kselftest

   - Fix backtraces reported in /proc/$pid/stack

   - Disable broken CnP implementation on NVIDIA Carmel

   - Typo fixes and ACPI documentation clarification

   - Fix some W=1 warnings"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kernel: disable CNP on Carmel
  arm64/process.c: fix Wmissing-prototypes build warnings
  kselftest/arm64: sve: Do not use non-canonical FFR register value
  arm64: mm: correct the inside linear map range during hotplug check
  arm64: kdump: update ppos when reading elfcorehdr
  arm64: cpuinfo: Fix a typo
  Documentation: arm64/acpi : clarify arm64 support of IBFT
  arm64: stacktrace: don't trace arch_stack_walk()
  arm64: csum: cast to the proper type

Redirect my older email addresses in the git logs.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add Asym_Pause to supported link modes (it is supported by HW).
Lack of Asym_Pause in supported modes can cause several problems,
i.e. it won't be possible to turn the autonegotiation on
with asymmetric pause settings (i.e. Tx on, Rx off).

Fixes: 4e91bcd5 ("i40e: Finish implementation of ethtool get settings")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Remove padding from RSS structures. Previous layout
could lead to unwanted compiler optimizations
in loops when iterating over key and lut arrays.

Fixes: 65ece6de ("virtchnl: Add missing explicit padding to structures")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Use my personal email, the @google.com one will stop functioning soon.

Link: https://lkml.kernel.org/r/ead0e9c32a2f70e0bde6f63b3b9470e0ef13d2ee.1616107969.git.andreyknvl@google.comSigned-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kernel test robot found that __kmap_local_sched_out() was not
correctly skipping the guard pages when DEBUG_KMAP_LOCAL_FORCE_MAP was
set.[1] This was due to DEBUG_HIGHMEM check being used.

Change the configuration check to be correct.

[1] https://lore.kernel.org/lkml/20210304083825.GB17830@xsang-OptiPlex-9020/

Link: https://lkml.kernel.org/r/20210318230657.1497881-1-ira.weiny@intel.com
Fixes: 0e91a0c6 ("mm/highmem: Provide CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Oliver Sang <oliver.sang@intel.com>
Cc: Chaitanya Kulkarni <Chaitanya.Kulkarni@wdc.com>
Cc: David Sterba <dsterba@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 34dc2efb ("memblock: fix section mismatch warning") marked
memblock_bottom_up() and memblock_set_bottom_up() as __init, but they
could be referenced from non-init functions like
memblock_find_in_range_node() on architectures that enable
CONFIG_ARCH_KEEP_MEMBLOCK.

For such builds kernel test robot reports:

   WARNING: modpost: vmlinux.o(.text+0x74fea4): Section mismatch in reference from the function memblock_find_in_range_node() to the function .init.text:memblock_bottom_up()
   The function memblock_find_in_range_node() references the function __init memblock_bottom_up().
   This is often because memblock_find_in_range_node lacks a __init  annotation or the annotation of memblock_bottom_up is wrong.

Replace __init annotations with __init_memblock annotations so that the
appropriate section will be selected depending on
CONFIG_ARCH_KEEP_MEMBLOCK.

Link: https://lore.kernel.org/lkml/202103160133.UzhgY0wt-lkp@intel.com
Link: https://lkml.kernel.org/r/20210316171347.14084-1-rppt@kernel.org
Fixes: 34dc2efb ("memblock: fix section mismatch warning")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Because memblock allocations are registered with kmemleak, the KFENCE
pool was seen by kmemleak as one large object.  Later allocations
through kfence_alloc() that were registered with kmemleak via
slab_post_alloc_hook() would then overlap and trigger a warning.
Therefore, once the pool is initialized, we can remove (free) it from
kmemleak again, since it should be treated as allocator-internal and be
seen as "free memory".

The second problem is that kmemleak is passed the rounded size, and not
the originally requested size, which is also the size of KFENCE objects.
To avoid kmemleak scanning past the end of an object and trigger a
KFENCE out-of-bounds error, fix the size if it is a KFENCE object.

For simplicity, to avoid a call to kfence_ksize() in
slab_post_alloc_hook() (and avoid new IS_ENABLED(CONFIG_DEBUG_KMEMLEAK)
guard), just call kfence_ksize() in mm/kmemleak.c:create_object().

Link: https://lkml.kernel.org/r/20210317084740.3099921-1-elver@google.comSigned-off-by: Marco Elver <elver@google.com>
Reported-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Luis Henriques <lhenriques@suse.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

LLVM changed the expected function signatures for llvm_gcda_start_file()
and llvm_gcda_emit_function() in the clang-11 release.  Users of
clang-11 or newer may have noticed their kernels failing to boot due to
a panic when enabling CONFIG_GCOV_KERNEL=y +CONFIG_GCOV_PROFILE_ALL=y.
Fix up the function signatures so calling these functions doesn't panic
the kernel.

Link: https://reviews.llvm.org/rGcdd683b516d147925212724b09ec6fb792a40041
Link: https://reviews.llvm.org/rG13a633b438b6500ecad9e4f936ebadf3411d0f44
Link: https://lkml.kernel.org/r/20210312224132.3413602-2-ndesaulniers@google.comSigned-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Prasad Sodagudi <psodagud@quicinc.com>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Fangrui Song <maskray@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Cc: <stable@vger.kernel.org>	[5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix warning with %lx / u64 mismatch:

  arch/ia64/kernel/err_inject.c: In function 'show_resources':
  arch/ia64/kernel/err_inject.c:62:22: warning:
    format '%lx' expects argument of type 'long unsigned int',
    but argument 3 has type 'u64' {aka 'long long unsigned int'}
     62 |  return sprintf(buf, "%lx", name[cpu]);   \
        |                      ^~~~~~~

Link: https://lkml.kernel.org/r/20210313104312.1548232-1-slyfox@gentoo.orgSigned-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The sleep warning happens at early boot right at secondary CPU
activation bootup:

    smp: Bringing up secondary CPUs ...
    BUG: sleeping function called from invalid context at mm/page_alloc.c:4942
    in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1
    CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.12.0-rc2-00007-g79e228d0b611-dirty #99
    ..
    Call Trace:
      show_stack+0x90/0xc0
      dump_stack+0x150/0x1c0
      ___might_sleep+0x1c0/0x2a0
      __might_sleep+0xa0/0x160
      __alloc_pages_nodemask+0x1a0/0x600
      alloc_page_interleave+0x30/0x1c0
      alloc_pages_current+0x2c0/0x340
      __get_free_pages+0x30/0xa0
      ia64_mca_cpu_init+0x2d0/0x3a0
      cpu_init+0x8b0/0x1440
      start_secondary+0x60/0x700
      start_ap+0x750/0x780
    Fixed BSP b0 value from CPU 1

As I understand interrupts are not enabled yet and system has a lot of
memory.  There is little chance to sleep and switch to GFP_ATOMIC should
be a no-op.

Link: https://lkml.kernel.org/r/20210315085045.204414-1-slyfox@gentoo.orgSigned-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The checks for maximum metadata block size is missing
SQUASHFS_BLOCK_OFFSET (the two byte length count).

Link: https://lkml.kernel.org/r/2069685113.2081245.1614583677427@webmail.123-reg.co.uk
Fixes: f37aa4c7 ("squashfs: add more sanity checks in id lookup")
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Cc: Sean Nyekjaer <sean@geanix.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>