This path, which shouldn't be *that* complicated, is now so littered
with per-chipset tweaks that it's hard to trace the order of what
happens.  HAS_PCH_SPLIT() is the most radical change across chipsets,
so it seems like a natural split to simplify the code.

This first commit just copies the existing code without changing
anything.

v2: updated to track removal of call to intel_enable_plane from i9xx_crtc_mode_set
Signed-off-by: Eric Anholt <eric@anholt.net>
Hella-acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

We need to ensure that we feed valid memory into the display plane
attached to the pipe when switching the pipe on. Otherwise, the display
engine may read through an invalid PTE and so throw an PGTBL_ER
exception.

As we need to perform load detection before even the first object is
allocated for the fbdev, there is no pre-existing object large enough
for us to borrow to use as the framebuffer. So we need to create one
and cleanup afterwards. At other times, the current fbcon may be large
enough for us to borrow it for duration of load detection.

Found by assert_fb_bound_for_plane().
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

As we now never attempt to steal a crtc for load detection, we either
set a mode on a new pipe, or change the dpms mode on an existing pipe.
Never both, so we can simplify the code slightly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

As we only allow the use of a disabled CRTC, we don't need to handle the
case where we are reusing an already enabled pipe.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

... and the no longer relevant comment. The code ceased stealing a pipe
for load detection a long time ago.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Check the return value from drm_crtc_set_mode(), report the failure
via a debug message and propagate the error back to the caller. This
prevents us from blissfully continuing to do the load detection on a
disabled pipe. Fortunately actual failure for modesetting is very rare,
and reported failures even rarer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

Required so that we don't obliterate the queue if initialising the
rings after the global IRQ handler is installed.

[Jesse, you recently looked at refactoring the IRQ installation
routines, does moving the initialisation of ring buffer data structures away
from that routine make sense in your grand scheme?]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>

If we're using vga switcheroo, the device may be turned off
and poking it can return random state. This provokes an OOPS fixed
separately by 8ff887c847 (drm/i915/dp: Be paranoid in case we disable a
DP before it is attached). Trying to use and respond to events on a
device that has been turned off by the user is in principle a silly thing
to do.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>

Despite the fixes in 548f245b (drm/i915: fix per-pipe reads after
"cleanup"), we missed one neighbouring read that was mistakenly replaced
with the reg value in 9db4a9c7 (drm/i915: cleanup per-pipe reg usage).
This was preventing us from correctly determining the mode the BIOS left
the panel in for machines that neither have an OpRegion nor access to
the VBT, (e.g. the EeePC 700).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

When enabling the plane, it is helpful to have already pointed that
plane to valid memory or else we may incur the wrath of a PGTBL_ER.
This code preserved the behaviour from the bad old days for unknown
reasons...

Found by assert_fb_bound_for_plane().

References: https://bugs.freedesktop.org/show_bug.cgi?id=36246Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

Given that the hardware may be left in a random condition by the BIOS,
it is conceivable that we then attempt to clear the DP_PIPEB_SELECT bit
without us ever enabling/attaching the DP encoder to a pipe. Thus
causing a NULL deference when we attempt to wait for a vblank on that
crtc.
Reported-and-tested-by: Bryan Christ <bryan.christ@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36314Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36456Reported-and-tested-by: Bo Wang <bo.b.wang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>

Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: fix gart setup on fusion parts (v2)
  drm: Send pending vblank events before disabling vblank.
  drm/radeon: fix regression on atom cards with hardcoded EDID record.
  drm/radeon/kms: add some new pci ids

Out of the entire GART/VM subsystem, the hw designers changed
the location of 3 regs.

v2: airlied: add parameter for userspace to work from.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is the least-bad behaviour.  It means that we signal the
vblank event before it actually happens, but since we're disabling
vblanks there's no guarantee that it will *ever* happen otherwise.

This prevents GL applications which use WaitMSC from hanging
indefinitely.
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Since fafcf94e introduced an edid size, it seems to have broken this path.

This manifest as oops on T500 Lenovo laptops with dual graphics primarily.

Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=33812

cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

In particular, s_freeing_list needs to be initialized early, since it is
used on some of the error paths when mounts fail.  The mapping inode,
for example, would be initialized and then free'd on an error path
before s_freeing_list was initialized, but the inode drop operation
needs the s_freeing_list to be set up.

Normally you'd never see this, because not only is logfs fairly rare,
but a successful mount will never have any issues.
Reported-by: werner <w.landgraf@ru.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'stable/bug-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen: mask_rw_pte mark RO all pagetable pages up to pgt_buf_top
  xen/mmu: Add workaround "x86-64, mm: Put early page table high"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: sdhci: Check mrq != NULL in sdhci_tasklet_finish
  mmc: sdhci: Check mrq->cmd in sdhci_tasklet_finish
  mmc: tmio: fix .set_ios(MMC_POWER_UP) handling
  mmc: fix a race between card-detect rescan and clock-gate work instances
  mmc: omap: Fix possible NULL pointer deref
  mmc: core: mmc_add_card(): fix missing break in switch statement
  mmc: sdhci-pci: Fix error case in sdhci_pci_probe_slot()

Merge branches 'x86-fixes-for-linus' and 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, reboot: Fix relocations in reboot_32.S
  x86, NUMA: Fix empty memblk detection in numa_cleanup_meminfo()
  x86, AMD: Fix APIC timer erratum 400 affecting K8 Rev.A-E processors

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix typo CONFIG_GENIRC_IRQ_SHOW_LEVEL

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wm831x-ts - move BTN_TOUCH reporting to data transfer
  Input: wm831x-ts - allow IRQ flags to be specified
  Input: wm831x-ts - fix races with IRQ management

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
  sysctl: net: call unregister_net_sysctl_table where needed
  Revert: veth: remove unneeded ifname code from veth_newlink()
  smsc95xx: fix reset check
  tg3: Fix failure to enable WoL by default when possible
  networking: inappropriate ioctl operation should return ENOTTY
  amd8111e: trivial typo spelling: Negotitate -> Negotiate
  ipv4: don't spam dmesg with "Using LC-trie" messages
  af_unix: Only allow recv on connected seqpacket sockets.
  mii: add support of pause frames in mii_get_an
  net: ftmac100: fix scheduling while atomic during PHY link status change
  usbnet: Transfer of maintainership
  usbnet: add support for some Huawei modems with cdc-ether ports
  bnx2: cancel timer on device removal
  iwl4965: fix "Received BA when not expected"
  iwlagn: fix "Received BA when not expected"
  dsa/mv88e6131: fix unknown multicast/broadcast forwarding on mv88e6085
  usbnet: Resubmit interrupt URB if device is open
  iwl4965: fix "TX Power requested while scanning"
  iwlegacy: led stay solid on when no traffic
  b43: trivial: update module info about ucode16_mimo firmware
  ...

ctl_table_headers registered with register_net_sysctl_table should
have been unregistered with the equivalent unregister_net_sysctl_table
Signed-off-by: Lucian Adrian Grijincu <lucian.grijincu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

84c49d8c ("veth: remove unneeded
ifname code from veth_newlink()") caused regression on veth
creation. This patch reverts the original one.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reset loop check should check the MII_BMCR register value for
BMCR_RESET rather than for MII_BMCR (the register address, which also
happens to be zero).
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3 is supposed to enable WoL by default on adapters which support
that, but it fails to do so unless the adapter's
/sys/devices/.../power/wakeup file contains 'enabled' during the
initialization of the adapter.  Fix that by making tg3 use
device_set_wakeup_enable() to enable wakeup automatically whenever
WoL should be enabled by default.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

ioctl() calls against a socket with an inappropriate ioctl operation
are incorrectly returning EINVAL rather than ENOTTY:

  [ENOTTY]
      Inappropriate I/O control operation.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=33992Signed-off-by: Lifeng Sun <lifongsun@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The use of base for %ebx in this file is arbitrary, *except* that we
also use it to compute the real-mode segment.  Therefore, make it so
that r_base really is the true address to which %ebx points.

This resolves kernel bugzilla 33302.
Reported-and-tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/n/tip-08os5wi3yq1no0y4i5m4z7he@git.kernel.org

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mask_rw_pte is currently checking if a pfn is a pagetable page if it
falls in the range pgt_buf_start - pgt_buf_end but that is incorrect
because pgt_buf_end is a moving target: pgt_buf_top is the real
boundary.
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

As a consequence of the commit:

commit 4b239f45
Author: Yinghai Lu <yinghai@kernel.org>
Date:   Fri Dec 17 16:58:28 2010 -0800

    x86-64, mm: Put early page table high

it causes the Linux kernel to crash under Xen:

mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) mm.c:2466:d0 Bad type (saw 7400000000000001 != exp 1000000000000000) for mfn b1d89 (pfn bacf7)
(XEN) mm.c:3027:d0 Error while pinning mfn b1d89
(XEN) traps.c:481:d0 Unhandled invalid opcode fault/trap [#6] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
...

The reason is that at some point init_memory_mapping is going to reach
the pagetable pages area and map those pages too (mapping them as normal
memory that falls in the range of addresses passed to init_memory_mapping
as argument). Some of those pages are already pagetable pages (they are
in the range pgt_buf_start-pgt_buf_end) therefore they are going to be
mapped RO and everything is fine.
Some of these pages are not pagetable pages yet (they fall in the range
pgt_buf_end-pgt_buf_top; for example the page at pgt_buf_end) so they
are going to be mapped RW.  When these pages become pagetable pages and
are hooked into the pagetable, xen will find that the guest has already
a RW mapping of them somewhere and fail the operation.
The reason Xen requires pagetables to be RO is that the hypervisor needs
to verify that the pagetables are valid before using them. The validation
operations are called "pinning" (more details in arch/x86/xen/mmu.c).

In order to fix the issue we mark all the pages in the entire range
pgt_buf_start-pgt_buf_top as RO, however when the pagetable allocation
is completed only the range pgt_buf_start-pgt_buf_end is reserved by
init_memory_mapping. Hence the kernel is going to crash as soon as one
of the pages in the range pgt_buf_end-pgt_buf_top is reused (b/c those
ranges are RO).

For this reason, this function is introduced which is called _after_
the init_memory_mapping has completed (in a perfect world we would
call this function from init_memory_mapping, but lets ignore that).

Because we are called _after_ init_memory_mapping the pgt_buf_[start,
end,top] have all changed to new values (b/c another init_memory_mapping
is called). Hence, the first time we enter this function, we save
away the pgt_buf_start value and update the pgt_buf_[end,top].

When we detect that the "old" pgt_buf_start through pgt_buf_end
PFNs have been reserved (so memblock_x86_reserve_range has been called),
we immediately set out to RW the "old" pgt_buf_end through pgt_buf_top.

And then we update those "old" pgt_buf_[end|top] with the new ones
so that we can redo this on the next pagetable.
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Reviewed-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
[v1: Updated with Jeremy's comments]
[v2: Added the crash output]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

* 'for-linus' of git://git.infradead.org/ubifs-2.6:
  UBIFS: seek journal heads to the latest bud in replay
  UBIFS: do not free write-buffers when in R/O mode

* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: (47 commits)
  CLKDEV: Fix clkdev return value for NULL clk case
  ARM: 6891/1: prevent heap corruption in OABI semtimedop
  ARM: kprobes: Tidy-up kprobes-decode.c
  ARM: kprobes: Add emulation of hint instructions like NOP and WFI
  ARM: kprobes: Add emulation of SBFX, UBFX, BFI and BFC instructions
  ARM: kprobes: Add emulation of MOVW and MOVT instructions
  ARM: kprobes: Reject probing of undefined data processing instructions
  ARM: kprobes: Remove redundant code in space_1111
  ARM: kprobes: Fix emulation of PLD instructions
  ARM: kprobes: Reject probing of SETEND instructions
  ARM: kprobes: Consolidate stub decoding functions
  ARM: kprobes: Reject probing of all coprocessor instructions
  ARM: kprobes: Fix emulation of USAD8 instructions
  ARM: kprobes: Fix emulation of SMUAD, SMUSD and SMMUL instructions
  ARM: kprobes: Fix emulation of SXTB16, SXTB, SXTH, UXTB16, UXTB and UXTH instructions
  ARM: kprobes: Reject probing of undefined media instructions
  ARM: kprobes: Add emulation of RBIT instruction
  ARM: kprobes: Reject probing of LDRB instructions which load PC
  ARM: kprobes: Fix emulation of LDRD and STRD instructions
  ARM: kprobes: Reject probing of LDR/STR instructions which update PC unpredictably
  ...

commit ab7798ff ("genirq: Expand generic
show_interrupts()") added the Kconfig option GENERIC_IRQ_SHOW_LEVEL to
accomodate PowerPC, but this doesn't actually enable the functionality due
to a typo in the #ifdef check.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Linux/PPC Development <linuxppc-dev@lists.ozlabs.org>
Link: http://lkml.kernel.org/r/%3Calpine.DEB.2.00.1104302251370.19068%40ayla.of.borg%3ESigned-off-by: Thomas Gleixner <tglx@linutronix.de>