- 07 Mar, 2017 6 commits
-
-
Gerd Hoffmann authored
Just use kmem_cache instead of rolling our own, limited implementation. Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1488377348-5006-1-git-send-email-kraxel@redhat.com
-
Gerd Hoffmann authored
Call qxl_add_monitors_config_modes() unconditionally. Do all sanity checks in that function. Fix sanity checks. monitors_config is the current monitor configuration, whereas client_monitors_config is the configuration requested by the spice client. So when filling the mode list, based on the spice client request, we need to look at client_monitors_config->count not monitors_config->count. Signed-off-by:
Gabriel Krisman Bertazi <krisman@collabora.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-5-git-send-email-kraxel@redhat.com
-
Gerd Hoffmann authored
Try to read the client monitors config at driver load time, even without explicit notification. So in case that info was filled before the driver loaded and we've missed the notifications because of that the settings will still be used. With that place we now have to take care to properly handle a empty client monitors config, so we don't trip over an uninitialized client monitors config. Signed-off-by:
-
Gerd Hoffmann authored
When reading the monitor config fails, don't retry forever. If it fails ten times in a row just give up to avoid the driver hangs. Also add a small delay after each attempt, so the host has a chance to complete a partial update. Signed-off-by:
-
Gerd Hoffmann authored
very old qxl hardware revisions (predating qxl ksm support by a few years) supported a fixed list of video modes only. The list is still provided by the virtual hardware, for backward compatibility reasons. The qxl kms driver never ever looks at it, except for dumping it to the kernel log at load time in case debug logging is enabled. Drop that pointless code. Signed-off-by:
-
Gabriel Krisman Bertazi authored
If fbdev emulation is disabled, the QXL shutdown path will try to clean a framebuffer that wasn't initialized, hitting the Oops below. The problem is that even when FBDEV_EMULATION is disabled we allocate the qfbdev strutucture, but we don't initialize it. The fix is to stop allocating the memory, since it won't be used. This allows the existing verification in the cleanup hook to do it's job preventing the oops. Now that we don't allocate the unused fbdev structure, we need to be careful when dereferencing it in the PM suspend hook. [ 24.284684] BUG: unable to handle kernel NULL pointer dereference at 00000000000002e0 [ 24.285627] IP: mutex_lock+0x18/0x30 [ 24.286049] PGD 78cdf067 [ 24.286050] PUD 7940f067 [ 24.286344] PMD 0 [ 24.286649] [ 24.287072] Oops: 0002 [#1] SMP [ 24.287422] Modules linked in: qxl [ 24.287806] CPU: 0 PID: 2328 Comm: bash Not tainted 4.10.0-rc5+ #97 [ 24.288515] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-20161025_171302-gandalf 04/01/2014 [ 24.289681] task: ffff88007c4c0000 task.stack: ffffc90001b58000 [ 24.290354] RIP: 0010:mutex_lock+0x18/0x30 [ 24.290812] RSP: 0018:ffffc90001b5bcb0 EFLAGS: 00010246 [ 24.291401] RAX: 0000000000000000 RBX: 00000000000002e0 RCX: 0000000000000000 [ 24.292209] RDX: ffff88007c4c0000 RSI: 0000000000000001 RDI: 00000000000002e0 [ 24.292987] RBP: ffffc90001b5bcb8 R08: fffffffffffffffe R09: 0000000000000001 [ 24.293797] R10: ffff880078d80b80 R11: 0000000000011400 R12: 0000000000000000 [ 24.294601] R13: 00000000000002e0 R14: ffffffffa0009c28 R15: 0000000000000060 [ 24.295439] FS: 00007f30e3acbb40(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000 [ 24.296364] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 24.296997] CR2: 00000000000002e0 CR3: 0000000078c7b000 CR4: 00000000000006f0 [ 24.297813] Call Trace: [ 24.298097] drm_framebuffer_cleanup+0x1f/0x70 [ 24.298612] qxl_fbdev_fini+0x68/0x90 [qxl] [ 24.299074] qxl_modeset_fini+0xd/0x30 [qxl] [ 24.299562] qxl_pci_remove+0x22/0x50 [qxl] [ 24.300025] pci_device_remove+0x34/0xb0 [ 24.300507] device_release_driver_internal+0x150/0x200 [ 24.301082] device_release_driver+0xd/0x10 [ 24.301587] unbind_store+0x108/0x150 [ 24.301993] drv_attr_store+0x20/0x30 [ 24.302402] sysfs_kf_write+0x32/0x40 [ 24.302827] kernfs_fop_write+0x108/0x190 [ 24.303269] __vfs_write+0x23/0x120 [ 24.303678] ? security_file_permission+0x36/0xb0 [ 24.304193] ? rw_verify_area+0x49/0xb0 [ 24.304636] vfs_write+0xb0/0x190 [ 24.305004] SyS_write+0x41/0xa0 [ 24.305362] entry_SYSCALL_64_fastpath+0x1a/0xa9 [ 24.305887] RIP: 0033:0x7f30e31d9620 [ 24.306285] RSP: 002b:00007ffc54b47e68 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 24.307128] RAX: ffffffffffffffda RBX: 00007f30e3497600 RCX: 00007f30e31d9620 [ 24.307928] RDX: 000000000000000d RSI: 0000000000da2008 RDI: 0000000000000001 [ 24.308727] RBP: 000000000070bc60 R08: 00007f30e3498760 R09: 00007f30e3acbb40 [ 24.309504] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000001 [ 24.310295] R13: 0000000000000000 R14: 0000000000000000 R15: 00007ffc54b47f34 [ 24.311095] Code: 0e 01 e9 7b fe ff ff 66 90 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 53 48 89 fb e8 83 e8 ff ff 65 48 8b 14 25 40 c4 00 00 31 c0 <3e> 48 0f b1 13 48 85 c0 74 08 48 89 df e8 66 fd ff ff 5b 5d c3 [ 24.313182] RIP: mutex_lock+0x18/0x30 RSP: ffffc90001b5bcb0 [ 24.313811] CR2: 00000000000002e0 [ 24.314208] ---[ end trace 29669c1593cae14b ]--- Signed-off-by:
-
- 06 Mar, 2017 11 commits
-
-
Sean Paul authored
Fixes the following link error when CONFIG_DRM_ANALOGIX_DP is not defined: ERROR: "analogix_dp_start_crc" [drivers/gpu/drm/rockchip/rockchipdrm.ko] undefined! ERROR: "analogix_dp_stop_crc" [drivers/gpu/drm/rockchip/rockchipdrm.ko] undefined! Fixes: 3190e58d ("drm/rockchip: Implement CRC debugfs API") Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com> Cc: Mark Yao <mark.yao@rock-chips.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: dri-devel@lists.freedesktop.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Cc: Emil Velikov <emil.l.velikov@gmail.com> Reviewed-by:
Emil Velikov <emil.l.velikov@gmail.com> Signed-off-by:
Sean Paul <seanpaul@chromium.org>
-
Sean Paul authored
This patch fixes the following compilation error when CONFIG_DEBUG_FS is not defined. ../drivers/gpu/drm/drm_dp_helper.c: In function ‘drm_dp_aux_crc_work’: ../drivers/gpu/drm/drm_dp_helper.c:1029:13: error: ‘struct drm_crtc’ has no member named ‘crc’ ../drivers/gpu/drm/drm_dp_helper.c:1031:12: error: ‘struct drm_crtc’ has no member named ‘crc’ make[4]: *** [drivers/gpu/drm/drm_dp_helper.o] Error 1 make[4]: *** Waiting for unfinished jobs.... Fixes: 79c1da7c ("drm/dp: add helpers for capture of frame CRCs") Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
-
Tomeu Vizoso authored
Implement the .set_crc_source() callback and call the DP helpers accordingly to start and stop CRC capture. This is only done if this CRTC is currently using the eDP connector. v3: Remove superfluous check on rockchip_crtc_state->output_type v6: Remove superfluous variable Signed-off-by:
Tomeu Vizoso <tomeu.vizoso@collabora.com> Acked-by:
Mark Yao <mark.yao@rock-chips.com> Signed-off-by:
-
Tomeu Vizoso authored
Add two simple functions that just take the drm_dp_aux from our struct and calls the corresponding DP helpers with it. v6: Pass to the DP helper the drm_crtc of the current connector (Sean Paul) Signed-off-by:
-
Tomeu Vizoso authored
Adds helpers for starting and stopping capture of frame CRCs through the DPCD. When capture is on, a worker waits for vblanks and retrieves the frame CRC to put it in the queue on the CRTC that is using the eDP connector, so it's passed to userspace. v2: Reuse drm_crtc_wait_one_vblank Update locking, as drm_crtc_add_crc_entry now takes the lock v3: Don't call wake_up_interruptible directly, that's now done in drm_crtc_add_crc_entry. v4: Style fixes (Sean Paul) Reworked retry of CRC reads (Sean Paul) Flush worker after stopping CRC generationa (Sean Paul) v5: Move back to make the retry explicitly once v6: Set and use the drm_crtc backpointer (Sean Paul) Signed-off-by: -
Tomeu Vizoso authored
This backpointer allows DP helpers to access the crtc it's currently being used for. v6: Have the backpointer be to drm_crtc (Sean Paul) Signed-off-by:
-
Maarten Lankhorst authored
There are new iterator macros that annotate whether the new or old state should be used. This is better than using a state that depends on whether it's called before or after swap. For clarity, also rename the variables from $obj_state to (old,new)_$obj_state as well. Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1487256430-7625-6-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by:
-
Maarten Lankhorst authored
This is a straightforward conversion that converts all the users of get_existing_state in atomic core to use get_old_state or get_new_state Changes since v1: - Fix using the wrong state in drm_atomic_helper_update_legacy_modeset_state. Changes since v2: - Use the correct state in disable_outputs() Changes since v3: - Rebase for link status training. Signed-off-by:
-
Maarten Lankhorst authored
After atomic commit, these macros should be used in place of get_existing_state. Also after commit get_xx_state should no longer be used because it may not have the required locks. The calls to drm_atomic_get_existing_$obj_state should no longer be used, and converted over to these new calls. Changes since v1: - Expand commit message. - Deprecate get_existing_*_state functions in the documentation. Signed-off-by:
-
Maarten Lankhorst authored
This function becomes a lot simpler when having passed both the old and new state to it. Looking at all callers, it seems that old_plane_state is never NULL so the check can be dropped. Signed-off-by:
-
Maarten Lankhorst authored
There are new iterator macros that annotate whether the new or old state should be used. This is better than using a state that depends on whether it's called before or after swap. For clarity, also rename the variables from $obj_state to (old,new)_$obj_state as well. Changes since v1: - Use old/new_*_state for variable names as much as possible. (pinchartl) - Expand commit message. Changes since v2: - Rebase on top of link training patches. - free -> cleanup (pinchartl) Signed-off-by:
-
- 05 Mar, 2017 5 commits
-
-
Laurent Pinchart authored
The THC63LVDM83D is a transparent LVDS encoder. Unlike dumb LVDS encoders it can be controlled through a few pins (power down, LVDS swing, clock edge selection) and requires power supplies. However, on several boards where the device is used neither the control pins nor the power supply are controllable. To avoid developing a separate device-specific driver add a "thine,thc63lvdm83d" compatible entry to the lvds-encoder driver. This will allow supporting many THC63LVDM83D-based boards easily, while allowing future development of an thc63lvdm83d driver when needed without breaking backward compatibility. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by:
Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-5-laurent.pinchart+renesas@ideasonboard.com
-
Laurent Pinchart authored
The ADV7123 is a transparent VGA DAC. Unlike dumb VGA DACs it can be controlled through a power save pin, and requires a power supply. However, on most boards where the device is used neither the power save signal nor the power supply are controllable. To avoid developing a separate device-specific driver add an "adi,adv7123" compatible entry to the dumb-vga-dac driver. This will allow supporting most ADV7123-based boards easily, while allowing future development of an adv7123 driver when needed without breaking backward compatibility. Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Laurent Pinchart authored
The LVDS encoder driver is a DRM bridge driver that supports the parallel to LVDS encoders that don't require any configuration. The driver thus doesn't interact with the device, but creates an LVDS connector for the panel and exposes its size and timing based on information retrieved from DT. Signed-off-by:
Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
-
Laurent Pinchart authored
The DT bindings support parallel to LVDS encoders that don't require any configuration, similarly to the dumb VGA DAC DT bindings. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Peter Senna Tschudin authored
The video processing pipeline on the second output on the GE B850v3: Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output Each bridge has a dedicated flash containing firmware for supporting the custom design. The result is that in this design neither the STDP4028 nor the STDP2690 behave as the stock bridges would. The compatible strings include the suffix "-ge-b850v3-fw" to make it clear that the driver is for the bridges with the firmware which is specific for the GE B850v3. The driver is powerless to control the video processing pipeline, as the two bridges behaves as a single one. The driver is only needed for telling the host about EDID / HPD, and for giving the host powers to ack interrupts. This driver adds one i2c_device for each bridge, but only one drm_bridge. This design allows the creation of a functional connector that is capable of reading EDID from the STDP2690 while handling interrupts on the STDP4028. Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Martyn Welch <martyn.welch@collabora.co.uk> Cc: Martin Donnelly <martin.donnelly@ge.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Rob Herring <robh@kernel.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: David Airlie <airlied@linux.ie> Cc: Thierry Reding <treding@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Archit Taneja <architt@codeaurora.org> Cc: Enric Balletbo <enric.balletbo@collabora.com> Signed-off-by:
Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by:
-
- 03 Mar, 2017 2 commits
-
-
Peter Senna Tschudin authored
Add MAINTAINERS entry for the second video output of the GE B850v3: STDP4028-ge-b850v3-fw bridges (LVDS-DP) STDP2690-ge-b850v3-fw bridges (DP-DP++) Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Martyn Welch <martyn.welch@collabora.co.uk> Cc: Martin Donnelly <martin.donnelly@ge.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Rob Herring <robh@kernel.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> CC: David Airlie <airlied@linux.ie> CC: Thierry Reding <treding@nvidia.com> CC: Thierry Reding <thierry.reding@gmail.com> CC: Archit Taneja <architt@codeaurora.org> Signed-off-by: -
Peter Senna Tschudin authored
Devicetree binding documentation for the second video output of the GE B850v3: STDP4028-ge-b850v3-fw bridges (LVDS-DP) STDP2690-ge-b850v3-fw bridges (DP-DP++) Added entry for MegaChips at: Documentation/devicetree/bindings/vendor-prefixes.txt Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Martyn Welch <martyn.welch@collabora.co.uk> Cc: Martin Donnelly <martin.donnelly@ge.com> Cc: Javier Martinez Canillas <javier@dowhile0.org> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Rob Herring <robh@kernel.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Acked-by:
-
- 02 Mar, 2017 4 commits
-
-
Eric Anholt authored
If a CMA allocation failed, the partially constructed BO would be unreferenced through the normal path, and we might choose to put it in the BO cache. If we then reused it before it expired from the cache, the kernel would OOPS. Signed-off-by:
Eric Anholt <eric@anholt.net> Fixes: c826a6e1 ("drm/vc4: Add a BO cache.") Reviewed-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170301185602.6873-2-eric@anholt.net
-
Eric Anholt authored
The from_cache flag was actually "the BO is invisible to userspace", so we can repurpose it to just zero out a cached BO and return it to userspace. Improves wall time for a loop of 5 glsl-algebraic-add-add-1 by -1.44989% +/- 0.862891% (n=28, 1 outlier removed from each that appeared to be other system noise) Note that there's an intel-gpu-tools test to check for the proper zeroing behavior here, which we continue to pass. Signed-off-by:
-
Daniel Vetter authored
This reverts commit 233ce881. I assumed it's ok, but really should have double-checked - CI caught tons of fail :( Cc: Jani Nikula <jani.nikula@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Acked-by:
Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170301171749.13053-1-daniel.vetter@ffwll.ch
-
Maxime Ripard authored
Implement legacy framebuffer ioctl FBIO_WAITFORVSYNC in the generic framebuffer emulation driver. Legacy framebuffer users like non kms/drm based OpenGL(ES)/EGL implementations may require the ioctl to synchronize drawing or buffer flip for double buffering. It is tested on the i.MX6. Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
- 01 Mar, 2017 12 commits
-
-
Gabriel Krisman Bertazi authored
Commit be7f735cd5ea ("drm: Rely on mode_config data for fb_helper initialization") dropped the num_crtc argument. Update the documentation to reflect that and prevent the kernel-doc warnings below: ./drivers/gpu/drm/drm_fb_cma_helper.c:557: warning: Excess function parameter 'num_crtc' description in 'drm_fbdev_cma_init' ./drivers/gpu/drm/drm_fb_cma_helper.c:558: warning: Excess function parameter 'num_crtc' description in 'drm_fbdev_cma_init' Fixes: be7f735cd5ea ("drm: Rely on mode_config data for fb_helper initialization") Signed-off-by: -
Chris Zhong authored
Reference the power domain incase dw-mipi power down when in use. Signed-off-by:
Chris Zhong <zyw@rock-chips.com> Reviewed-by:
-
Chris Zhong authored
Set the lanes bps to 1 / 0.9 times of pclk, the margin is not enough for some panel, it will cause the screen display is not normal, so increases the badnwidth to 1 / 0.8. Signed-off-by:
-
Chris Zhong authored
Signed-off-by:
-
Chris Zhong authored
The MIPI DSI do not need check the validity of resolution, the max resolution should depend VOP. Hence, remove rk3288_mipi_dsi_mode_valid here. Signed-off-by:
-
Chris Zhong authored
correct the coding style, according the checkpatch scripts Signed-off-by:
-
Chris Zhong authored
The vopb/vopl switch register of RK3399 mipi is different from RK3288, the default setting for mipi dsi mode is different too, so add a of_device_id structure to distinguish them, and make sure set the correct mode before mipi phy init. Signed-off-by:
-
Chris Zhong authored
The dw-mipi-dsi of rk3399 is almost the same as rk3288, the rk3399 has additional phy config clock. Signed-off-by:
-
John Keeping authored
In order to fully reset the state of the MIPI controller we must assert this reset. This is slightly more complicated than it could be in order to maintain compatibility with device trees that do not specify the reset property. Signed-off-by:
John Keeping <john@metanate.com> Reviewed-by:
-
John Keeping authored
Signed-off-by:
-
John Keeping authored
This ensures that the output resolution is known before fbcon loads. mipi_dsi_host_register() is moved above dw_mipi_dsi_register() to simplify error cleanup since the order of these operations does not matter. Signed-off-by:
-
John Keeping authored
When connected to the MIPI DSI output, we need to use N{H,V}SYNC for the internal connection but these flags are meaningless for DSI panels. Switch the test so that we do not set the P{H,V}SYNC bits unless the mode requires it. Signed-off-by:
-
