- 13 Sep, 2022 31 commits
-
-
Krzysztof Kozlowski authored
The TCSR mutex bindings allow device to be described only with address space (so it uses MMIO, not syscon regmap). This seems reasonable as TCSR mutex is actually a dedicated IO address space and it also fixes DT schema checks: qcom/ipq6018-cp01-c1.dtb: hwlock: 'reg' is a required property qcom/ipq6018-cp01-c1.dtb: hwlock: 'syscon' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220909092035.223915-12-krzysztof.kozlowski@linaro.org
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
There are 174 GPIOs in SC7280. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
The pin configuration is selected with "pins", not "pin" property. Fixes: 1209e924 ("arm64: dts: qcom: sm8350-sagami: Enable and populate I2C/SPI nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Judy Hsiao authored
Fix the DMIC no sound issue of villager-r1 by using "PP1800_L2C" as the DMIC power source to match the hardware schematic. This patch: 1. set vdd-micb-supply to PP1800_L2C as the MIC Bias voltage regulator. 2. In audio-routing, set VA DMIC01~VA DMIC03 to use the vdd-micb-supply setting. Co-developed-by:Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Signed-off-by:
Judy Hsiao <judyhsiao@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add dt nodes for sound card support on rev5+ (aka CRD 3.0/3.1) boards, which is using WCD9385 headset playback, capture, I2S speaker playback and DMICs via VA macro. Signed-off-by:
Venkata Prasad Potturu <quic_potturu@quicinc.com> Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add dt nodes for sound card support on revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards, which is using WCD9385 headset playback, capture, I2S speaker playback and DMICs via VA macro. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable lpass cpu node and add pin control and dai-links for audio on sc7280 based platforms of rev5+ (aka CRD 3.0/3.1) boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable lpass cpu node and add pin control and dai-links for audio on sc7280 based platforms of revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add lpass cpu node for audio on sc7280 based platforms. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add max98360a codec node for audio use case on all herobrine boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add max98360a codec node for audio use case on revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Add amp_en node for max98360a codec pin control. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add wcd9385 codec node for audio use case on CRD rev5+ (aka CRD 3.0/3.1) boards. Add tlmm gpio property for switching CTIA/OMTP Headset. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Add wcd9385 codec node for audio use case on sc7280 based platforms of revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Add tlmm gpio property for switching CTIA/OMTP Headset. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable rx, tx and va macro codecs and soundwire nodes for CRD rev5+ (aka CRD 3.0/3.1) boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Enable rx, tx and va macro codecs and soundwire nodes on revision 3, 4 (aka CRD 1.0 and 2.0) and IDP boards. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
SC7280 has VA, TX and RX macros with SoundWire Controllers to attach with external codecs using soundwire masters. Add these nodes for sc7280 based platforms audio use case. Signed-off-by:
-
Taniya Das authored
Support external mclk to interface external MI2S clocks for SC7280. Fixes: 4185b27b ("dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7280") Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Taniya Das <quic_tdas@quicinc.com> Reviewed-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Taniya Das authored
Add support for LPASS audio clock gating for RX/TX/SWA core bus clocks for SC7280. Update reg property min/max items in YAML schema. Fixes: 4185b27b ("dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7280") Acked-by:
-
Taniya Das authored
When this property is set, the remoteproc is used to boot the LPASS and therefore lpass_q6ss_ahbm_clk and lpass_q6ss_ahbs_clk clocks would be used to bring LPASS out of reset and the rest of the lpass clocks would be controlled directly by the remoteproc. This is a cleanup done to handle overlap of regmap of lpasscc and lpass_aon blocks. Signed-off-by:
Satya Priya <quic_c_skakit@quicinc.com> Reviewed-by:
-
Jimmy Chen authored
This adds LTE skus for villager device tree files. Signed-off-by:
Jimmy Chen <jinghung.chen3@hotmail.com> Reviewed-by:
Sibi Sankar <quic_sibis@quicinc.com> Signed-off-by:
-
Jimmy Chen authored
This adds sc7280-herobrine-villager-r1.dts for villager device tree files. Herobrine-r1 is exactly the same as -r0 except that it uses a different audio solution (it uses the same one as the CRD). Signed-off-by:
-
Jimmy Chen authored
This adds a LTE skus for Chromebook Villager to the yaml. Signed-off-by:
-
- 08 Sep, 2022 2 commits
-
-
Bhupesh Sharma authored
The 'snps,ptp-ref-clk-rate' and 'snps,ptp-req-clk-rate' properties are not supported by the stmmac driver currently, so remove them from the sa8155p-adp ethernet node as well. Cc: Bjorn Andersson <andersson@kernel.org> Cc: Rob Herring <robh@kernel.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: David Miller <davem@davemloft.net> Signed-off-by:
Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by:
-
Krzysztof Kozlowski authored
Correct CPU BWMON unit address to match the "reg" property. Reported-by:
-
- 06 Sep, 2022 7 commits
-
-
Jakob Hauser authored
Add magnetometer Yamaha YAS537 to the DeviceTree of samsung-serranove. The YAS537 variant was recently added to the Yamaha YAS magnetometers driver [1]. In the DeviceTree of samsung-serranove for the Android kernel, there is unfortunately no information on interrupts or pinctrl [2]. In the Android kernel driver for magnetometer Yamaha YAS537, there is a device-specific matrix to correct an ellipsoid shape of the measure values into a sphere shape [3]. This could be converted and applied to a mount-matrix. However, the current state of the mainline Yamaha YAS537 driver needs post-process calibration in userspace anyway, as it lacks a formula to center the measure values around zero. The correction of the ellipsoid into a sphere can be done in the post-process calibration as well. A mount-matrix is needed nonetheless. When putting samsung-serranove flat on a table in portrait orientation heading north, the Yamaha YAS537 magnetometer axes natively point X+ to north, Y+ to east and Z+ into the ground, which corresponds to a common way to define the Earth's magnetic field coordinate system [4]. According to the IIO definition, it should be Y+ to north, X+ to east and Z+ upwards [5], which corresponds to a common device coordinate system and eases sensor fusing. [1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/drivers/iio/magnetometer/yamaha-yas530.c?id=65f79b501030678393eae0ae03d60a8151fbef55 [2] https://github.com/msm8916-mainline/android_kernel_qcom_msm8916/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-eur-r03.dtsi#L318-L321 [3] https://github.com/msm8916-mainline/android_kernel_qcom_msm8916/blob/GT-I9195I/drivers/iio/magnetometer/yas_mag_drv-yas537.c#L105-L106 [4] https://en.wikipedia.org/wiki/Earth%27s_magnetic_field#Characteristics [5] https://github.com/torvalds/linux/blob/v5.19/Documentation/devicetree/bindings/iio/mount-matrix.txt#L93-L126 Cc: Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
Jakob Hauser <jahau@rocketmail.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Bhupesh Sharma authored
Commit eeca7d46 ("arm64: dts: qcom: pm8350c: Drop PWM reg declaration") dropped PWM reg declaration for pm8350c pwm(s), but there is a leftover 'reg' entry inside the lpg/pwm node in sc8280xp dts file. Remove the same. While at it, also remove the unused unit address in the node label. Also, since dt-bindings expect LPG/PWM node name to be "pwm", use correct node name as well, to fix the following error reported by 'make dtbs_check': 'lpg' does not match any of the regexes Fixes: eeca7d46 ("arm64: dts: qcom: pm8350c: Drop PWM reg declaration") Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Bjorn Andersson <andersson@kernel.org> Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by:
-
Luca Weiss authored
The PM7250B is primarily used for charger and fuel gauge on Fairphone 4 but also has some thermal zones that we can configure already. Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Reviewed-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by:
-
Luca Weiss authored
PM7250B is a PMIC primarily used for charging and fuel gauge but also has some of the standard functionality like temp-alarm, adc, etc. Add the .dtsi with some of the functionality added. Signed-off-by:
-
Johan Hovold authored
Some recent changes that added new syscon nodes used misspelled node names. Fixes: 86d7c946 arm64: dts: qcom: sm8150: split TCSR halt regs out of mutex Fixes: 0da60338 arm64: dts: qcom: sdm630: split TCSR halt regs out of mutex Fixes: 8a8531e6 arm64: dts: qcom: sdm845: split TCSR halt regs out of mutex Fixes: d9a2214d arm64: dts: qcom: sc7280: split TCSR halt regs out of mutex Fixes: ce1ac53c arm64: dts: qcom: sc7180: split TCSR halt regs out of mutex Fixes: fc10cfa3 arm64: dts: qcom: msm8998: split TCSR halt regs out of mutex Fixes: 100ce220 arm64: dts: qcom: msm8996: split TCSR halt regs out of mutex Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Signed-off-by:
-
Johan Hovold authored
The primary and secondary USB controllers can be used to wake the system from suspend so mark them accordingly. Signed-off-by:
-
Sheng-Liang Pan authored
Add a basic device tree for the herobrine evoker board. Signed-off-by:
Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com> Reviewed-by:
-
