[ Upstream commit fba2efda ]

When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.

So this patch fixes it, only return while setting PFC failed.

Fixes: 44e59e37 ("net: hns3: do not return GE PFC setting err when initializing")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 62909da8 ]

>From the DS2408 datasheet [1]:
"Resume Command function checks the status of the RC flag and, if it is set,
 directly transfers control to the control functions, similar to a Skip ROM
 command. The only way to set the RC flag is through successfully executing
 the Match ROM, Search ROM, Conditional Search ROM, or Overdrive-Match ROM
 command"

The function currently works perfectly fine in a multidrop bus, but when we
have only a single slave connected, then only a Skip ROM is used and Match
ROM is not called at all. This is leading to problems e.g. with single one
DS2408 connected, as the Resume Command is not working properly and the
device is responding with failing results after the Resume Command.

This commit is fixing this by using a Skip ROM instead in those cases.
The bandwidth / performance advantage is exactly the same.

Refs:
[1] https://datasheets.maximintegrated.com/en/ds/DS2408.pdfSigned-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Reviewed-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 06095f34 ]

Now CPSW ALE will set/clean Host port bit in Unregistered Multicast Flood
Mask (UNREG_MCAST_FLOOD_MASK) for every VLAN without checking if this port
belongs to VLAN or not when ALLMULTI mode flag is set for nedev. This is
working in non dual_mac mode, but in dual_mac - it causes
enabling/disabling ALLMULTI flag for both ports.

Hence fix it by adding additional parameter to cpsw_ale_set_allmulti() to
specify ALE port number for which ALLMULTI has to be enabled and check if
port belongs to VLAN before modifying UNREG_MCAST_FLOOD_MASK.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9b019acb ]

The NOHZ idle balancer runs on the lowest idle CPU. This can
interfere with isolated CPUs, so confine it to HK_FLAG_MISC
housekeeping CPUs.

HK_FLAG_SCHED is not used for this because it is not set anywhere
at the moment. This could be folded into HK_FLAG_SCHED once that
option is fixed.

The problem was observed with increased jitter on an application
running on CPU0, caused by NOHZ idle load balancing being run on
CPU1 (an SMT sibling).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190412042613.28930-1-npiggin@gmail.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4d95c517 ]

snd_hda_codec_device_new() is used by both legacy HDA and ASoC
driver. However, we will call snd_hdac_device_unregister() in
snd_hdac_ext_bus_device_remove() for ASoC device. This patch uses
the type flag in hdac_device struct to determine is it a ASoC device
or legacy HDA device and call snd_hdac_device_unregister() in
snd_hda_codec_dev_free() only if it is a legacy HDA device.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 729829d7 ]

To register data for the next kernel (command line, oldmem_base, etc.) the
current kernel needs to find the ELF segment that contains head.S. This is
currently done by checking ifor 'phdr->p_paddr == 0'. This works fine for
the current kernel build but in theory the first few pages could be
skipped. Make the detection more robust by checking if the entry point lies
within the segment.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f848bfd8 ]

Sometimes during connection recovery when there is a failure to resolve
ARP, and offload connection was not issued, driver tries to flush pending
offload connection work which was not queued up.

kernel: WARNING: CPU: 19 PID: 10110 at kernel/workqueue.c:3030 __flush_work.isra.34+0x19c/0x1b0
kernel: CPU: 19 PID: 10110 Comm: iscsid Tainted: G W 5.1.0-rc4 #11
kernel: Hardware name: Dell Inc. PowerEdge R730/0599V5, BIOS 2.9.1 12/04/2018
kernel: RIP: 0010:__flush_work.isra.34+0x19c/0x1b0
kernel: Code: 8b fb 66 0f 1f 44 00 00 31 c0 eb ab 48 89 ef c6 07 00 0f 1f 40 00 fb 66 0f 1f 44 00 00 31 c0 eb 96 e8 08 16 fe ff 0f 0b eb 8d <0f> 0b 31 c0 eb 87 0f 1f 40 00 66 2e 0f 1
f 84 00 00 00 00 00 0f 1f
kernel: RSP: 0018:ffffa6b4054dba68 EFLAGS: 00010246
kernel: RAX: 0000000000000000 RBX: ffff91df21c36fc0 RCX: 0000000000000000
kernel: RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff91df21c36fc0
kernel: RBP: ffff91df21c36ef0 R08: 0000000000000000 R09: 0000000000000000
kernel: R10: 0000000000000038 R11: ffffa6b4054dbd60 R12: ffffffffc05e72c0
kernel: R13: ffff91db10280820 R14: 0000000000000048 R15: 0000000000000000
kernel: FS:  00007f5d83cc1740(0000) GS:ffff91df2f840000(0000) knlGS:0000000000000000
kernel: CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: 0000000001cc5000 CR3: 0000000465450002 CR4: 00000000001606e0
kernel: Call Trace:
kernel: ? try_to_del_timer_sync+0x4d/0x80
kernel: qedi_ep_disconnect+0x3b/0x410 [qedi]
kernel: ? 0xffffffffc083c000
kernel: ? klist_iter_exit+0x14/0x20
kernel: ? class_find_device+0x93/0xf0
kernel: iscsi_if_ep_disconnect.isra.18+0x58/0x70 [scsi_transport_iscsi]
kernel: iscsi_if_recv_msg+0x10e2/0x1510 [scsi_transport_iscsi]
kernel: ? copyout+0x22/0x30
kernel: ? _copy_to_iter+0xa0/0x430
kernel: ? _cond_resched+0x15/0x30
kernel: ? __kmalloc_node_track_caller+0x1f9/0x270
kernel: iscsi_if_rx+0xa5/0x1e0 [scsi_transport_iscsi]
kernel: netlink_unicast+0x17f/0x230
kernel: netlink_sendmsg+0x2d2/0x3d0
kernel: sock_sendmsg+0x36/0x50
kernel: ___sys_sendmsg+0x280/0x2a0
kernel: ? timerqueue_add+0x54/0x80
kernel: ? enqueue_hrtimer+0x38/0x90
kernel: ? hrtimer_start_range_ns+0x19f/0x2c0
kernel: __sys_sendmsg+0x58/0xa0
kernel: do_syscall_64+0x5b/0x180
kernel: entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cf612c59 ]

Manage the -EPROBE_DEFER error case for the wake IRQ.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f22b1ba1 ]

The device's remove() attempts to shut down the delayed_work scheduled
on the kernel-global workqueue by calling flush_scheduled_work().

Unfortunately, flush_scheduled_work() does not prevent the delayed_work
from re-scheduling itself. The delayed_work might run after the device
has been removed, and touch the already de-allocated info structure.
This is a potential use-after-free.

Fix by calling cancel_delayed_work_sync() during remove(): this ensures
that the delayed work is properly cancelled, is no longer running, and
is not able to re-schedule itself.

This issue was detected with the help of Coccinelle.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 30f24eab ]

If for some reason the device gives us an RX interrupt before we're
ready for it, perhaps during device power-on with misconfigured IRQ
causes mapping or so, we can crash trying to access the queues.

Prevent that by checking that we actually have RXQs and that they
were properly allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7ac1e464 ]

When we failed to find a root key in btrfs_update_root(), we just panic.

That's definitely not cool, fix it by outputting an unique error
message, aborting current transaction and return -EUCLEAN. This should
not normally happen as the root has been used by the callers in some
way.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ff612ba7 ]

We've been seeing the following sporadically throughout our fleet

panic: kernel BUG at fs/btrfs/relocation.c:4584!
netversion: 5.0-0
Backtrace:
 #0 [ffffc90003adb880] machine_kexec at ffffffff81041da8
 #1 [ffffc90003adb8c8] __crash_kexec at ffffffff8110396c
 #2 [ffffc90003adb988] crash_kexec at ffffffff811048ad
 #3 [ffffc90003adb9a0] oops_end at ffffffff8101c19a
 #4 [ffffc90003adb9c0] do_trap at ffffffff81019114
 #5 [ffffc90003adba00] do_error_trap at ffffffff810195d0
 #6 [ffffc90003adbab0] invalid_op at ffffffff81a00a9b
    [exception RIP: btrfs_reloc_cow_block+692]
    RIP: ffffffff8143b614  RSP: ffffc90003adbb68  RFLAGS: 00010246
    RAX: fffffffffffffff7  RBX: ffff8806b9c32000  RCX: ffff8806aad00690
    RDX: ffff880850b295e0  RSI: ffff8806b9c32000  RDI: ffff88084f205bd0
    RBP: ffff880849415000   R8: ffffc90003adbbe0   R9: ffff88085ac90000
    R10: ffff8805f7369140  R11: 0000000000000000  R12: ffff880850b295e0
    R13: ffff88084f205bd0  R14: 0000000000000000  R15: 0000000000000000
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 #7 [ffffc90003adbbb0] __btrfs_cow_block at ffffffff813bf1cd
 #8 [ffffc90003adbc28] btrfs_cow_block at ffffffff813bf4b3
 #9 [ffffc90003adbc78] btrfs_search_slot at ffffffff813c2e6c

The way relocation moves data extents is by creating a reloc inode and
preallocating extents in this inode and then copying the data into these
preallocated extents.  Once we've done this for all of our extents,
we'll write out these dirty pages, which marks the extent written, and
goes into btrfs_reloc_cow_block().  From here we get our current
reloc_control, which _should_ match the reloc_control for the current
block group we're relocating.

However if we get an ENOSPC in this path at some point we'll bail out,
never initiating writeback on this inode.  Not a huge deal, unless we
happen to be doing relocation on a different block group, and this block
group is now rc->stage == UPDATE_DATA_PTRS.  This trips the BUG_ON() in
btrfs_reloc_cow_block(), because we expect to be done modifying the data
inode.  We are in fact done modifying the metadata for the data inode
we're currently using, but not the one from the failed block group, and
thus we BUG_ON().

(This happens when writeback finishes for extents from the previous
group, when we are at btrfs_finish_ordered_io() which updates the data
reloc tree (inode item, drops/adds extent items, etc).)

Fix this by writing out the reloc data inode always, and then breaking
out of the loop after that point to keep from tripping this BUG_ON()
later.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
[ add note from Filipe ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 39ad3173 ]

When doing fallocate, we first add the range to the reserve_list and
then reserve the quota.  If quota reservation fails, we'll release all
reserved parts of reserve_list.

However, cur_offset is not updated to indicate that this range is
already been inserted into the list.  Therefore, the same range is freed
twice.  Once at list_for_each_entry loop, and once at the end of the
function.  This will result in WARN_ON on bytes_may_use when we free the
remaining space.

At the end, under the 'out' label we have a call to:

   btrfs_free_reserved_data_space(inode, data_reserved, alloc_start, alloc_end - cur_offset);

The start offset, third argument, should be cur_offset.

Everything from alloc_start to cur_offset was freed by the
list_for_each_entry_safe_loop.

Fixes: 18513091 ("btrfs: update btrfs_space_info's bytes_may_use timely")
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Robbie Ko <robbieko@synology.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f2c65fb3 ]

When modules and BPF filters are loaded, there is a time window in
which some memory is both writable and executable. An attacker that has
already found another vulnerability (e.g., a dangling pointer) might be
able to exploit this behavior to overwrite kernel code. Prevent having
writable executable PTEs in this stage.

In addition, avoiding having W+X mappings can also slightly simplify the
patching of modules code on initialization (e.g., by alternatives and
static-key), as would be done in the next patch. This was actually the
main motivation for this patch.

To avoid having W+X mappings, set them initially as RW (NX) and after
they are set as RO set them as X as well. Setting them as executable is
done as a separate step to avoid one core in which the old PTE is cached
(hence writable), and another which sees the updated PTE (executable),
which would break the W^X protection.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: https://lkml.kernel.org/r/20190426001143.4983-12-namit@vmware.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 300ec741 ]

Since fc_remote_port_delete() must be called with interrupts enabled, do
not disable interrupts when calling that function. Remove the lockin calls
from around the put_sess() call. This is safe because the function that is
called when the final reference is dropped, qlt_unreg_sess(), grabs the
proper locks. This patch avoids that lockdep reports the following:

WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
kworker/2:1/62 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
0000000009e679b3 (&(&k->k_lock)->rlock){+.+.}, at: klist_next+0x43/0x1d0

and this task is already holding:
00000000a033b71c (&(&ha->tgt.sess_lock)->rlock){-...}, at: qla24xx_delete_sess_fn+0x55/0xf0 [qla2xxx_scst]
which would create a new lock dependency:
 (&(&ha->tgt.sess_lock)->rlock){-...} -> (&(&k->k_lock)->rlock){+.+.}

but this new dependency connects a HARDIRQ-irq-safe lock:
 (&(&ha->tgt.sess_lock)->rlock){-...}

... which became HARDIRQ-irq-safe at:
  lock_acquire+0xe3/0x200
  _raw_spin_lock_irqsave+0x3d/0x60
  qla24xx_report_id_acquisition+0xa69/0xe30 [qla2xxx_scst]
  qla24xx_process_response_queue+0x69e/0x1270 [qla2xxx_scst]
  qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx_scst]
  __handle_irq_event_percpu+0x79/0x3c0
  handle_irq_event_percpu+0x70/0xf0
  handle_irq_event+0x5a/0x8b
  handle_edge_irq+0x12c/0x310
  handle_irq+0x192/0x20a
  do_IRQ+0x73/0x160
  ret_from_intr+0x0/0x1d
  default_idle+0x23/0x1f0
  arch_cpu_idle+0x15/0x20
  default_idle_call+0x35/0x40
  do_idle+0x2bb/0x2e0
  cpu_startup_entry+0x1d/0x20
  start_secondary+0x2a8/0x320
  secondary_startup_64+0xa4/0xb0

to a HARDIRQ-irq-unsafe lock:
 (&(&k->k_lock)->rlock){+.+.}

... which became HARDIRQ-irq-unsafe at:
...
  lock_acquire+0xe3/0x200
  _raw_spin_lock+0x32/0x50
  klist_add_tail+0x33/0xb0
  device_add+0x7e1/0xb50
  device_create_groups_vargs+0x11c/0x150
  device_create_with_groups+0x89/0xb0
  vtconsole_class_init+0xb2/0x124
  do_one_initcall+0xc5/0x3ce
  kernel_init_freeable+0x295/0x32e
  kernel_init+0x11/0x11b
  ret_from_fork+0x3a/0x50

other info that might help us debug this:

 Possible interrupt unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&(&k->k_lock)->rlock);
                               local_irq_disable();
                               lock(&(&ha->tgt.sess_lock)->rlock);
                               lock(&(&k->k_lock)->rlock);
  <Interrupt>
    lock(&(&ha->tgt.sess_lock)->rlock);

 *** DEADLOCK ***

3 locks held by kworker/2:1/62:
 #0: 00000000a4319c16 ((wq_completion)"qla2xxx_wq"){+.+.}, at: process_one_work+0x437/0xa80
 #1: 00000000ffa34c42 ((work_completion)(&sess->del_work)){+.+.}, at: process_one_work+0x437/0xa80
 #2: 00000000a033b71c (&(&ha->tgt.sess_lock)->rlock){-...}, at: qla24xx_delete_sess_fn+0x55/0xf0 [qla2xxx_scst]

the dependencies between HARDIRQ-irq-safe lock and the holding lock:
-> (&(&ha->tgt.sess_lock)->rlock){-...} ops: 8 {
   IN-HARDIRQ-W at:
                    lock_acquire+0xe3/0x200
                    _raw_spin_lock_irqsave+0x3d/0x60
                    qla24xx_report_id_acquisition+0xa69/0xe30 [qla2xxx_scst]
                    qla24xx_process_response_queue+0x69e/0x1270 [qla2xxx_scst]
                    qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx_scst]
                    __handle_irq_event_percpu+0x79/0x3c0
                    handle_irq_event_percpu+0x70/0xf0
                    handle_irq_event+0x5a/0x8b
                    handle_edge_irq+0x12c/0x310
                    handle_irq+0x192/0x20a
                    do_IRQ+0x73/0x160
                    ret_from_intr+0x0/0x1d
                    default_idle+0x23/0x1f0
                    arch_cpu_idle+0x15/0x20
                    default_idle_call+0x35/0x40
                    do_idle+0x2bb/0x2e0
                    cpu_startup_entry+0x1d/0x20
                    start_secondary+0x2a8/0x320
                    secondary_startup_64+0xa4/0xb0
   INITIAL USE at:
                   lock_acquire+0xe3/0x200
                   _raw_spin_lock_irqsave+0x3d/0x60
                   qla24xx_report_id_acquisition+0xa69/0xe30 [qla2xxx_scst]
                   qla24xx_process_response_queue+0x69e/0x1270 [qla2xxx_scst]
                   qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx_scst]
                   __handle_irq_event_percpu+0x79/0x3c0
                   handle_irq_event_percpu+0x70/0xf0
                   handle_irq_event+0x5a/0x8b
                   handle_edge_irq+0x12c/0x310
                   handle_irq+0x192/0x20a
                   do_IRQ+0x73/0x160
                   ret_from_intr+0x0/0x1d
                   default_idle+0x23/0x1f0
                   arch_cpu_idle+0x15/0x20
                   default_idle_call+0x35/0x40
                   do_idle+0x2bb/0x2e0
                   cpu_startup_entry+0x1d/0x20
                   start_secondary+0x2a8/0x320
                   secondary_startup_64+0xa4/0xb0
 }
 ... key      at: [<ffffffffa0c0d080>] __key.85462+0x0/0xfffffffffff7df80 [qla2xxx_scst]
 ... acquired at:
   lock_acquire+0xe3/0x200
   _raw_spin_lock_irqsave+0x3d/0x60
   klist_next+0x43/0x1d0
   device_for_each_child+0x96/0x110
   scsi_target_block+0x3c/0x40 [scsi_mod]
   fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc]
   qla2x00_mark_device_lost+0xa0b/0xa30 [qla2xxx_scst]
   qlt_unreg_sess+0x1c6/0x380 [qla2xxx_scst]
   qla24xx_delete_sess_fn+0xe6/0xf0 [qla2xxx_scst]
   process_one_work+0x511/0xa80
   worker_thread+0x67/0x5b0
   kthread+0x1d2/0x1f0
   ret_from_fork+0x3a/0x50

the dependencies between the lock to be acquired
 and HARDIRQ-irq-unsafe lock:
-> (&(&k->k_lock)->rlock){+.+.} ops: 13831 {
   HARDIRQ-ON-W at:
                    lock_acquire+0xe3/0x200
                    _raw_spin_lock+0x32/0x50
                    klist_add_tail+0x33/0xb0
                    device_add+0x7e1/0xb50
                    device_create_groups_vargs+0x11c/0x150
                    device_create_with_groups+0x89/0xb0
                    vtconsole_class_init+0xb2/0x124
                    do_one_initcall+0xc5/0x3ce
                    kernel_init_freeable+0x295/0x32e
                    kernel_init+0x11/0x11b
                    ret_from_fork+0x3a/0x50
   SOFTIRQ-ON-W at:
                    lock_acquire+0xe3/0x200
                    _raw_spin_lock+0x32/0x50
                    klist_add_tail+0x33/0xb0
                    device_add+0x7e1/0xb50
                    device_create_groups_vargs+0x11c/0x150
                    device_create_with_groups+0x89/0xb0
                    vtconsole_class_init+0xb2/0x124
                    do_one_initcall+0xc5/0x3ce
                    kernel_init_freeable+0x295/0x32e
                    kernel_init+0x11/0x11b
                    ret_from_fork+0x3a/0x50
   INITIAL USE at:
                   lock_acquire+0xe3/0x200
                   _raw_spin_lock+0x32/0x50
                   klist_add_tail+0x33/0xb0
                   device_add+0x7e1/0xb50
                   device_create_groups_vargs+0x11c/0x150
                   device_create_with_groups+0x89/0xb0
                   vtconsole_class_init+0xb2/0x124
                   do_one_initcall+0xc5/0x3ce
                   kernel_init_freeable+0x295/0x32e
                   kernel_init+0x11/0x11b
                   ret_from_fork+0x3a/0x50
 }
 ... key      at: [<ffffffff83ed8780>] __key.15491+0x0/0x40
 ... acquired at:
   lock_acquire+0xe3/0x200
   _raw_spin_lock_irqsave+0x3d/0x60
   klist_next+0x43/0x1d0
   device_for_each_child+0x96/0x110
   scsi_target_block+0x3c/0x40 [scsi_mod]
   fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc]
   qla2x00_mark_device_lost+0xa0b/0xa30 [qla2xxx_scst]
   qlt_unreg_sess+0x1c6/0x380 [qla2xxx_scst]
   qla24xx_delete_sess_fn+0xe6/0xf0 [qla2xxx_scst]
   process_one_work+0x511/0xa80
   worker_thread+0x67/0x5b0
   kthread+0x1d2/0x1f0
   ret_from_fork+0x3a/0x50

stack backtrace:
CPU: 2 PID: 62 Comm: kworker/2:1 Tainted: G           O      5.0.7-dbg+ #8
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: qla2xxx_wq qla24xx_delete_sess_fn [qla2xxx_scst]
Call Trace:
 dump_stack+0x86/0xca
 check_usage.cold.52+0x473/0x563
 __lock_acquire+0x11c0/0x23e0
 lock_acquire+0xe3/0x200
 _raw_spin_lock_irqsave+0x3d/0x60
 klist_next+0x43/0x1d0
 device_for_each_child+0x96/0x110
 scsi_target_block+0x3c/0x40 [scsi_mod]
 fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc]
 qla2x00_mark_device_lost+0xa0b/0xa30 [qla2xxx_scst]
 qlt_unreg_sess+0x1c6/0x380 [qla2xxx_scst]
 qla24xx_delete_sess_fn+0xe6/0xf0 [qla2xxx_scst]
 process_one_work+0x511/0xa80
 worker_thread+0x67/0x5b0
 kthread+0x1d2/0x1f0
 ret_from_fork+0x3a/0x50

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d4023db7 ]

This patch avoids that lockdep reports the following warning:

=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
5.1.0-rc1-dbg+ #11 Tainted: G        W
-----------------------------------------------------
rmdir/1478 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
00000000e7ac4607 (&(&k->k_lock)->rlock){+.+.}, at: klist_next+0x43/0x1d0

and this task is already holding:
00000000cf0baf5e (&(&ha->tgt.sess_lock)->rlock){-...}, at: tcm_qla2xxx_close_session+0x57/0xb0 [tcm_qla2xxx]
which would create a new lock dependency:
 (&(&ha->tgt.sess_lock)->rlock){-...} -> (&(&k->k_lock)->rlock){+.+.}

but this new dependency connects a HARDIRQ-irq-safe lock:
 (&(&ha->tgt.sess_lock)->rlock){-...}

... which became HARDIRQ-irq-safe at:
  lock_acquire+0xe3/0x200
  _raw_spin_lock_irqsave+0x3d/0x60
  qla2x00_fcport_event_handler+0x1f3d/0x22b0 [qla2xxx]
  qla2x00_async_login_sp_done+0x1dc/0x1f0 [qla2xxx]
  qla24xx_process_response_queue+0xa37/0x10e0 [qla2xxx]
  qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx]
  __handle_irq_event_percpu+0x79/0x3c0
  handle_irq_event_percpu+0x70/0xf0
  handle_irq_event+0x5a/0x8b
  handle_edge_irq+0x12c/0x310
  handle_irq+0x192/0x20a
  do_IRQ+0x73/0x160
  ret_from_intr+0x0/0x1d
  default_idle+0x23/0x1f0
  arch_cpu_idle+0x15/0x20
  default_idle_call+0x35/0x40
  do_idle+0x2bb/0x2e0
  cpu_startup_entry+0x1d/0x20
  start_secondary+0x24d/0x2d0
  secondary_startup_64+0xa4/0xb0

to a HARDIRQ-irq-unsafe lock:
 (&(&k->k_lock)->rlock){+.+.}

... which became HARDIRQ-irq-unsafe at:
...
  lock_acquire+0xe3/0x200
  _raw_spin_lock+0x32/0x50
  klist_add_tail+0x33/0xb0
  device_add+0x7f4/0xb60
  device_create_groups_vargs+0x11c/0x150
  device_create_with_groups+0x89/0xb0
  vtconsole_class_init+0xb2/0x124
  do_one_initcall+0xc5/0x3ce
  kernel_init_freeable+0x295/0x32e
  kernel_init+0x11/0x11b
  ret_from_fork+0x3a/0x50

other info that might help us debug this:

 Possible interrupt unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&(&k->k_lock)->rlock);
                               local_irq_disable();
                               lock(&(&ha->tgt.sess_lock)->rlock);
                               lock(&(&k->k_lock)->rlock);
  <Interrupt>
    lock(&(&ha->tgt.sess_lock)->rlock);

 *** DEADLOCK ***

4 locks held by rmdir/1478:
 #0: 000000002c7f1ba4 (sb_writers#10){.+.+}, at: mnt_want_write+0x32/0x70
 #1: 00000000c85eb147 (&default_group_class[depth - 1]#2/1){+.+.}, at: do_rmdir+0x217/0x2d0
 #2: 000000002b164d6f (&sb->s_type->i_mutex_key#13){++++}, at: vfs_rmdir+0x7e/0x1d0
 #3: 00000000cf0baf5e (&(&ha->tgt.sess_lock)->rlock){-...}, at: tcm_qla2xxx_close_session+0x57/0xb0 [tcm_qla2xxx]

the dependencies between HARDIRQ-irq-safe lock and the holding lock:
-> (&(&ha->tgt.sess_lock)->rlock){-...} ops: 127 {
   IN-HARDIRQ-W at:
                    lock_acquire+0xe3/0x200
                    _raw_spin_lock_irqsave+0x3d/0x60
                    qla2x00_fcport_event_handler+0x1f3d/0x22b0 [qla2xxx]
                    qla2x00_async_login_sp_done+0x1dc/0x1f0 [qla2xxx]
                    qla24xx_process_response_queue+0xa37/0x10e0 [qla2xxx]
                    qla24xx_msix_rsp_q+0x79/0xf0 [qla2xxx]
                    __handle_irq_event_percpu+0x79/0x3c0
                    handle_irq_event_percpu+0x70/0xf0
                    handle_irq_event+0x5a/0x8b
                    handle_edge_irq+0x12c/0x310
                    handle_irq+0x192/0x20a
                    do_IRQ+0x73/0x160
                    ret_from_intr+0x0/0x1d
                    default_idle+0x23/0x1f0
                    arch_cpu_idle+0x15/0x20
                    default_idle_call+0x35/0x40
                    do_idle+0x2bb/0x2e0
                    cpu_startup_entry+0x1d/0x20
                    start_secondary+0x24d/0x2d0
                    secondary_startup_64+0xa4/0xb0
   INITIAL USE at:
                   lock_acquire+0xe3/0x200
                   _raw_spin_lock_irqsave+0x3d/0x60
                   qla2x00_loop_resync+0xb3d/0x2690 [qla2xxx]
                   qla2x00_do_dpc+0xcee/0xf30 [qla2xxx]
                   kthread+0x1d2/0x1f0
                   ret_from_fork+0x3a/0x50
 }
 ... key      at: [<ffffffffa125f700>] __key.62804+0x0/0xfffffffffff7e900 [qla2xxx]
 ... acquired at:
   __lock_acquire+0x11ed/0x1b60
   lock_acquire+0xe3/0x200
   _raw_spin_lock_irqsave+0x3d/0x60
   klist_next+0x43/0x1d0
   device_for_each_child+0x96/0x110
   scsi_target_block+0x3c/0x40 [scsi_mod]
   fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc]
   qla2x00_mark_device_lost+0x4d3/0x500 [qla2xxx]
   qlt_unreg_sess+0x104/0x2c0 [qla2xxx]
   tcm_qla2xxx_close_session+0xa2/0xb0 [tcm_qla2xxx]
   target_shutdown_sessions+0x17b/0x190 [target_core_mod]
   core_tpg_del_initiator_node_acl+0xf3/0x1f0 [target_core_mod]
   target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
   config_item_release+0x9f/0x120 [configfs]
   config_item_put+0x29/0x2b [configfs]
   configfs_rmdir+0x3d2/0x520 [configfs]
   vfs_rmdir+0xb3/0x1d0
   do_rmdir+0x25c/0x2d0
   __x64_sys_rmdir+0x24/0x30
   do_syscall_64+0x77/0x220
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

the dependencies between the lock to be acquired
 and HARDIRQ-irq-unsafe lock:
-> (&(&k->k_lock)->rlock){+.+.} ops: 14568 {
   HARDIRQ-ON-W at:
                    lock_acquire+0xe3/0x200
                    _raw_spin_lock+0x32/0x50
                    klist_add_tail+0x33/0xb0
                    device_add+0x7f4/0xb60
                    device_create_groups_vargs+0x11c/0x150
                    device_create_with_groups+0x89/0xb0
                    vtconsole_class_init+0xb2/0x124
                    do_one_initcall+0xc5/0x3ce
                    kernel_init_freeable+0x295/0x32e
                    kernel_init+0x11/0x11b
                    ret_from_fork+0x3a/0x50
   SOFTIRQ-ON-W at:
                    lock_acquire+0xe3/0x200
                    _raw_spin_lock+0x32/0x50
                    klist_add_tail+0x33/0xb0
                    device_add+0x7f4/0xb60
                    device_create_groups_vargs+0x11c/0x150
                    device_create_with_groups+0x89/0xb0
                    vtconsole_class_init+0xb2/0x124
                    do_one_initcall+0xc5/0x3ce
                    kernel_init_freeable+0x295/0x32e
                    kernel_init+0x11/0x11b
                    ret_from_fork+0x3a/0x50
   INITIAL USE at:
                   lock_acquire+0xe3/0x200
                   _raw_spin_lock+0x32/0x50
                   klist_add_tail+0x33/0xb0
                   device_add+0x7f4/0xb60
                   device_create_groups_vargs+0x11c/0x150
                   device_create_with_groups+0x89/0xb0
                   vtconsole_class_init+0xb2/0x124
                   do_one_initcall+0xc5/0x3ce
                   kernel_init_freeable+0x295/0x32e
                   kernel_init+0x11/0x11b
                   ret_from_fork+0x3a/0x50
 }
 ... key      at: [<ffffffff83f3d900>] __key.15805+0x0/0x40
 ... acquired at:
   __lock_acquire+0x11ed/0x1b60
   lock_acquire+0xe3/0x200
   _raw_spin_lock_irqsave+0x3d/0x60
   klist_next+0x43/0x1d0
   device_for_each_child+0x96/0x110
   scsi_target_block+0x3c/0x40 [scsi_mod]
   fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc]
   qla2x00_mark_device_lost+0x4d3/0x500 [qla2xxx]
   qlt_unreg_sess+0x104/0x2c0 [qla2xxx]
   tcm_qla2xxx_close_session+0xa2/0xb0 [tcm_qla2xxx]
   target_shutdown_sessions+0x17b/0x190 [target_core_mod]
   core_tpg_del_initiator_node_acl+0xf3/0x1f0 [target_core_mod]
   target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
   config_item_release+0x9f/0x120 [configfs]
   config_item_put+0x29/0x2b [configfs]
   configfs_rmdir+0x3d2/0x520 [configfs]
   vfs_rmdir+0xb3/0x1d0
   do_rmdir+0x25c/0x2d0
   __x64_sys_rmdir+0x24/0x30
   do_syscall_64+0x77/0x220
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

stack backtrace:
CPU: 7 PID: 1478 Comm: rmdir Tainted: G        W         5.1.0-rc1-dbg+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
 dump_stack+0x86/0xca
 check_usage.cold.59+0x473/0x563
 check_prev_add.constprop.43+0x1f1/0x1170
 __lock_acquire+0x11ed/0x1b60
 lock_acquire+0xe3/0x200
 _raw_spin_lock_irqsave+0x3d/0x60
 klist_next+0x43/0x1d0
 device_for_each_child+0x96/0x110
 scsi_target_block+0x3c/0x40 [scsi_mod]
 fc_remote_port_delete+0xe7/0x1c0 [scsi_transport_fc]
 qla2x00_mark_device_lost+0x4d3/0x500 [qla2xxx]
 qlt_unreg_sess+0x104/0x2c0 [qla2xxx]
 tcm_qla2xxx_close_session+0xa2/0xb0 [tcm_qla2xxx]
 target_shutdown_sessions+0x17b/0x190 [target_core_mod]
 core_tpg_del_initiator_node_acl+0xf3/0x1f0 [target_core_mod]
 target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
 config_item_release+0x9f/0x120 [configfs]
 config_item_put+0x29/0x2b [configfs]
 configfs_rmdir+0x3d2/0x520 [configfs]
 vfs_rmdir+0xb3/0x1d0
 do_rmdir+0x25c/0x2d0
 __x64_sys_rmdir+0x24/0x30
 do_syscall_64+0x77/0x220
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e209783d ]

Implementations of the .write_pending() callback functions must guarantee
that an appropriate LIO core callback function will be called immediately or
at a later time.  Make sure that this guarantee is met for aborted SCSI
commands.

[mkp: typo]

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 694833ee ("scsi: tcm_qla2xxx: Do not allow aborted cmd to advance.") # v4.13.
Fixes: a07100e0 ("qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM") # v4.5.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 24afabdb ]

Make sure that the allocated interrupts are freed if allocating memory for
the msix_entries array fails.

Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4ebe36c9 ]

Currently the error return path from kobject_init_and_add() is not
followed by a call to kobject_put() - which means we are leaking the
kobject.

Fix it by adding a call to kobject_put() in the error path of
kobject_init_and_add().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7ae3f6e1 ]

Using a jiffies timer creates a dependency on the tick_do_timer_cpu
incrementing jiffies. If that CPU has locked up and jiffies is not
incrementing, the watchdog heartbeat timer for all CPUs stops and
creates false positives and confusing warnings on local CPUs, and
also causes the SMP detector to stop, so the root cause is never
detected.

Fix this by using hrtimer based timers for the watchdog heartbeat,
like the generic kernel hardlockup detector.

Cc: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reported-by: Ravikumar Bangoria <ravi.bangoria@in.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reported-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3c0dab44 ]

Since alloc_module() will not set the pages as executable soon, set
ftrace trampoline pages as executable after they are allocated.

For the time being, do not change ftrace to use the text_poke()
interface. As a result, ftrace still breaks W^X.
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-10-namit@vmware.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 89a37842 ]

Remove mt76_queue dependency from tx_queue_skb function pointer and
rely on mt76_tx_qid instead. This is a preliminary patch to introduce
mt76_sw_queue support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 74dd022f ]

When building with -Wunused-but-set-variable, the compiler shouts about
a number of pte_unmap() users, since this expands to an empty macro on
arm64:

  | mm/gup.c: In function 'gup_pte_range':
  | mm/gup.c:1727:16: warning: variable 'ptem' set but not used
  | [-Wunused-but-set-variable]
  | mm/gup.c: At top level:
  | mm/memory.c: In function 'copy_pte_range':
  | mm/memory.c:821:24: warning: variable 'orig_dst_pte' set but not used
  | [-Wunused-but-set-variable]
  | mm/memory.c:821:9: warning: variable 'orig_src_pte' set but not used
  | [-Wunused-but-set-variable]
  | mm/swap_state.c: In function 'swap_ra_info':
  | mm/swap_state.c:641:15: warning: variable 'orig_pte' set but not used
  | [-Wunused-but-set-variable]
  | mm/madvise.c: In function 'madvise_free_pte_range':
  | mm/madvise.c:318:9: warning: variable 'orig_pte' set but not used
  | [-Wunused-but-set-variable]

Rewrite pte_unmap() as a static inline function, which silences the
warnings.
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1f5b62f0 ]

The VDSO code uses the kernel helper that was originally designed
to abstract the access between 32 and 64bit systems. It worked so
far because this function is declared as 'inline'.

As we're about to revamp that part of the code, the VDSO would
break. Let's fix it by doing what should have been done from
the start, a proper system register access.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b5b5a27b ]

During probe, return the provided errors value instead of -ENODEV.
This allows the driver to be deferred probed if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f10b83de ]

If the BAR is zero size, it indicates it was never successfully mapped.
Ensure that the BAR is valid during initialization before attempting to
use it.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 23583f77 ]

When the DSDT tables expose devices with subdevices and a set of
hierarchical _DSD properties, the data returned by
acpi_get_next_subnode() is incorrect, with the results suggesting a bad
pointer assignment. The parser works fine with device_nodes or
data_nodes, but not with a combination of the two.

The problem is traced to an invalid pointer used when jumping from
handling device_nodes to data nodes. The existing code looks for data
nodes below the last subdevice found instead of the common root. Fix
by forcing the acpi_device pointer to be derived from the same fwnode
for the two types of subnodes.

This same problem of handling device and data nodes was already fixed
in a similar way by 'commit bf4703fd ("ACPI / property: fix data
node parsing in acpi_get_next_subnode()")' but broken later by 'commit
34055190 ("ACPI / property: Add fwnode_get_next_child_node()")', so
this should probably go to linux-stable all the way to 4.12
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e025da3d ]

If "ret_len" is negative then it could lead to a NULL dereference.

The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer.  Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd().  We memcpy() to and
from the buffer so it would result in a NULL dereference.

The fix is to change the types so that "ret_len" can't be negative.  (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).

Fixes: 1bacb048 ("brcmfmac: replace cfg80211 testmode with vendor command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6f4e0219 ]

When the state of rep was introduced, it was also designed to prevent
duplicate unloading of the same rep. Considering the following two
flows when an eswitch manager is at switchdev mode with n VF reps loaded.

+--------------------------------------+--------------------------------+
| cpu-0                                | cpu-1                          |
| --------                             | --------                       |
| mlx5_ib_remove                       | mlx5_eswitch_disable_sriov     |
|  mlx5_ib_unregister_vport_reps       |  esw_offloads_cleanup          |
|   mlx5_eswitch_unregister_vport_reps |   esw_offloads_unload_all_reps |
|    __unload_reps_all_vport           |    __unload_reps_all_vport     |
+--------------------------------------+--------------------------------+

These two flows will try to unload the same rep. Per original design,
once one flow unloads the rep, the state moves to REGISTERED. The 2nd
flow will no longer needs to do the unload and bails out. However, as
read and write of the state is not atomic, when 1st flow is doing the
unload, the state is still LOADED, 2nd flow is able to do the same
unload action. Kernel crash will happen.

To solve this, driver should do atomic test-and-set for the state. So
that only one flow can change the rep state from LOADED to REGISTERED,
and proceed to do the actual unloading.

Since the state is changing to atomic type, all other read/write should
be atomic action as well.

Fixes: f121e0ea (net/mlx5: E-Switch, Add state to eswitch vport representors)
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 29f21337 ]

Calculate the divisor for the SCR (Serial Clock Rate), avoiding
that the SSP transmission rate can be greater than the device rate.

When the division between the SSP clock and the device rate generates
a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the
device SPI max frequency.

For example, with:

 - ssp_clk  = 50 MHz
 - dev freq = 15 MHz

without this patch the SSP clock will be greater than 15 MHz:

 - 25 MHz for PXA25x_SSP and CE4100_SSP
 - 16,56 MHz for the others

Instead, with this patch, we have in both case an SSP clock of 12.5MHz,
so the max rate of the SPI device clock is respected.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ea751227 ]

During randconfig builds, I occasionally run into an invalid configuration
of the freescale FIQ sound support:

WARNING: unmet direct dependencies detected for SND_SOC_IMX_PCM_FIQ
  Depends on [m]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && SND_IMX_SOC [=m]
  Selected by [y]:
  - SND_SOC_FSL_SPDIF [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && SND_IMX_SOC [=m]!=n && (MXC_TZIC [=n] || MXC_AVIC [=y])

sound/soc/fsl/imx-ssi.o: In function `imx_ssi_remove':
imx-ssi.c:(.text+0x28): undefined reference to `imx_pcm_fiq_exit'
sound/soc/fsl/imx-ssi.o: In function `imx_ssi_probe':
imx-ssi.c:(.text+0xa64): undefined reference to `imx_pcm_fiq_init'

The Kconfig warning is a result of the symbol being defined inside of
the "if SND_IMX_SOC" block, and is otherwise harmless. The link error
is more tricky and happens with SND_SOC_IMX_SSI=y, which may or may not
imply FIQ support. However, if SND_SOC_FSL_SSI is set to =m at the same
time, that selects SND_SOC_IMX_PCM_FIQ as a loadable module dependency,
which then causes a link failure from imx-ssi.

The solution here is to make SND_SOC_IMX_PCM_FIQ built-in whenever
one of its potential users is built-in.

Fixes: ff40260f ("ASoC: fsl: refine DMA/FIQ dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e5c27498 ]

atmel_qspi objects are kept in spi_controller objects, so, first get
pointer to spi_controller object and then get atmel_qspi object from
spi_controller object.

Fixes: 2d30ac5e ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 860b7d22 ]

The data structure (i.e struct imc_mem_info) to hold the memory address
information for nest imc units is allocated based on the number of nodes
in the system.

nest_imc_event_init() traverse this struct array to calculate the memory
base address for the event-cpu. If we fail to find a match for the event
cpu's chip-id in imc_mem_info struct array, then the do-while loop will
iterate until we crash.

Fix this by changing the loop exit condition based on the number of
non zero vbase elements in the array, since the allocation is done for
nr_chips + 1.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 885dcd70 ("powerpc/perf: Add nest IMC PMU support")
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5d085ec0 ]

This is detected by Coverity scan: CID: 1440481
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a913e5e8 ]

Nest hardware counter memory resides in a per-chip reserve-memory.
During nest_imc_event_init(), chip-id of the event-cpu is considered to
calculate the base memory addresss for that cpu. Return, proper error
condition if the chip_id calculated is invalid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 885dcd70 ("powerpc/perf: Add nest IMC PMU support")
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 30180e84 ]

If the hdmi codec startup fails, it should clear the current_substream
pointer to free the device. This is properly done for the audio_startup()
callback but for snd_pcm_hw_constraint_eld().

Make sure the pointer cleared if an error is reported.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 73103c7f ]

The following kernel panic happens due to the io_data buffer gets deallocated
before the async io is completed. Add a check for the case where io_data buffer
should be deallocated by ffs_user_copy_worker.

[   41.663334] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[   41.672099] #PF error: [normal kernel read fault]
[   41.677356] PGD 20c974067 P4D 20c974067 PUD 20c973067 PMD 0
[   41.683687] Oops: 0000 [#1] PREEMPT SMP
[   41.687976] CPU: 1 PID: 7 Comm: kworker/u8:0 Tainted: G     U            5.0.0-quilt-2e5dc0ac-00790-gd8c79f2-dirty #2
[   41.705309] Workqueue: adb ffs_user_copy_worker
[   41.705316] RIP: 0010:__vunmap+0x2a/0xc0
[   41.705318] Code: 0f 1f 44 00 00 48 85 ff 0f 84 87 00 00 00 55 f7 c7 ff 0f 00 00 48 89 e5 41 55 41 89 f5 41 54 53 48 89 fb 75 71 e8 56 d7 ff ff <4c> 8b 60 48 4d 85 e4 74 76 48 89 df e8 25 ff ff ff 45 85 ed 74 46
[   41.705320] RSP: 0018:ffffbc3a40053df0 EFLAGS: 00010286
[   41.705322] RAX: 0000000000000000 RBX: ffffbc3a406f1000 RCX: 0000000000000000
[   41.705323] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 00000000ffffffff
[   41.705324] RBP: ffffbc3a40053e08 R08: 000000000001fb79 R09: 0000000000000037
[   41.705325] R10: ffffbc3a40053b68 R11: ffffbc3a40053cad R12: fffffffffffffff2
[   41.705326] R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffffffffff
[   41.705328] FS:  0000000000000000(0000) GS:ffff9e2977a80000(0000) knlGS:0000000000000000
[   41.705329] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.705330] CR2: 0000000000000048 CR3: 000000020c994000 CR4: 00000000003406e0
[   41.705331] Call Trace:
[   41.705338]  vfree+0x50/0xb0
[   41.705341]  ffs_user_copy_worker+0xe9/0x1c0
[   41.705344]  process_one_work+0x19f/0x3e0
[   41.705348]  worker_thread+0x3f/0x3b0
[   41.829766]  kthread+0x12b/0x150
[   41.833371]  ? process_one_work+0x3e0/0x3e0
[   41.838045]  ? kthread_create_worker_on_cpu+0x70/0x70
[   41.843695]  ret_from_fork+0x3a/0x50
[   41.847689] Modules linked in: hci_uart bluetooth ecdh_generic rfkill_gpio dwc3_pci dwc3 snd_usb_audio mei_me tpm_crb snd_usbmidi_lib xhci_pci xhci_hcd mei tpm snd_hwdep cfg80211 snd_soc_skl snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_hda_ext_core snd_hda_core videobuf2_dma_sg crlmodule
[   41.876880] CR2: 0000000000000048
[   41.880584] ---[ end trace 2bc4addff0f2e673 ]---
[   41.891346] RIP: 0010:__vunmap+0x2a/0xc0
[   41.895734] Code: 0f 1f 44 00 00 48 85 ff 0f 84 87 00 00 00 55 f7 c7 ff 0f 00 00 48 89 e5 41 55 41 89 f5 41 54 53 48 89 fb 75 71 e8 56 d7 ff ff <4c> 8b 60 48 4d 85 e4 74 76 48 89 df e8 25 ff ff ff 45 85 ed 74 46
[   41.916740] RSP: 0018:ffffbc3a40053df0 EFLAGS: 00010286
[   41.922583] RAX: 0000000000000000 RBX: ffffbc3a406f1000 RCX: 0000000000000000
[   41.930563] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 00000000ffffffff
[   41.938540] RBP: ffffbc3a40053e08 R08: 000000000001fb79 R09: 0000000000000037
[   41.946520] R10: ffffbc3a40053b68 R11: ffffbc3a40053cad R12: fffffffffffffff2
[   41.954502] R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffffffffff
[   41.962482] FS:  0000000000000000(0000) GS:ffff9e2977a80000(0000) knlGS:0000000000000000
[   41.971536] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.977960] CR2: 0000000000000048 CR3: 000000020c994000 CR4: 00000000003406e0
[   41.985930] Kernel panic - not syncing: Fatal exception
[   41.991817] Kernel Offset: 0x16000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[   42.009525] Rebooting in 10 seconds..
[   52.014376] ACPI MEMORY or I/O RESET_REG.

Fixes: 772a7a72 ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Fei Yang <fei.yang@intel.com>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 41a91c60 ]

dwc3_gadget_suspend() is called under dwc->lock spinlock. In such context
calling synchronize_irq() is not allowed. Move the problematic call out
of the protected block to fix the following kernel BUG during system
suspend:

BUG: sleeping function called from invalid context at kernel/irq/manage.c:112
in_atomic(): 1, irqs_disabled(): 128, pid: 1601, name: rtcwake
6 locks held by rtcwake/1601:
 #0: f70ac2a2 (sb_writers#7){.+.+}, at: vfs_write+0x130/0x16c
 #1: b5fe1270 (&of->mutex){+.+.}, at: kernfs_fop_write+0xc0/0x1e4
 #2: 7e597705 (kn->count#60){.+.+}, at: kernfs_fop_write+0xc8/0x1e4
 #3: 8b3527d0 (system_transition_mutex){+.+.}, at: pm_suspend+0xc4/0xc04
 #4: fc7f1c42 (&dev->mutex){....}, at: __device_suspend+0xd8/0x74c
 #5: 4b36507e (&(&dwc->lock)->rlock){....}, at: dwc3_gadget_suspend+0x24/0x3c
irq event stamp: 11252
hardirqs last  enabled at (11251): [<c09c54a4>] _raw_spin_unlock_irqrestore+0x6c/0x74
hardirqs last disabled at (11252): [<c09c4d44>] _raw_spin_lock_irqsave+0x1c/0x5c
softirqs last  enabled at (9744): [<c0102564>] __do_softirq+0x3a4/0x66c
softirqs last disabled at (9737): [<c0128528>] irq_exit+0x140/0x168
Preemption disabled at:
[<00000000>]   (null)
CPU: 7 PID: 1601 Comm: rtcwake Not tainted
5.0.0-rc3-next-20190122-00039-ga3f4ee4f8a52 #5252
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c01110f0>] (unwind_backtrace) from [<c010d120>] (show_stack+0x10/0x14)
[<c010d120>] (show_stack) from [<c09a4d04>] (dump_stack+0x90/0xc8)
[<c09a4d04>] (dump_stack) from [<c014c700>] (___might_sleep+0x22c/0x2c8)
[<c014c700>] (___might_sleep) from [<c0189d68>] (synchronize_irq+0x28/0x84)
[<c0189d68>] (synchronize_irq) from [<c05cbbf8>] (dwc3_gadget_suspend+0x34/0x3c)
[<c05cbbf8>] (dwc3_gadget_suspend) from [<c05bd020>] (dwc3_suspend_common+0x154/0x410)
[<c05bd020>] (dwc3_suspend_common) from [<c05bd34c>] (dwc3_suspend+0x14/0x2c)
[<c05bd34c>] (dwc3_suspend) from [<c051c730>] (platform_pm_suspend+0x2c/0x54)
[<c051c730>] (platform_pm_suspend) from [<c05285d4>] (dpm_run_callback+0xa4/0x3dc)
[<c05285d4>] (dpm_run_callback) from [<c0528a40>] (__device_suspend+0x134/0x74c)
[<c0528a40>] (__device_suspend) from [<c052c508>] (dpm_suspend+0x174/0x588)
[<c052c508>] (dpm_suspend) from [<c0182134>] (suspend_devices_and_enter+0xc0/0xe74)
[<c0182134>] (suspend_devices_and_enter) from [<c0183658>] (pm_suspend+0x770/0xc04)
[<c0183658>] (pm_suspend) from [<c0180ddc>] (state_store+0x6c/0xcc)
[<c0180ddc>] (state_store) from [<c09a9a70>] (kobj_attr_store+0x14/0x20)
[<c09a9a70>] (kobj_attr_store) from [<c02d6800>] (sysfs_kf_write+0x4c/0x50)
[<c02d6800>] (sysfs_kf_write) from [<c02d594c>] (kernfs_fop_write+0xfc/0x1e4)
[<c02d594c>] (kernfs_fop_write) from [<c02593d8>] (__vfs_write+0x2c/0x160)
[<c02593d8>] (__vfs_write) from [<c0259694>] (vfs_write+0xa4/0x16c)
[<c0259694>] (vfs_write) from [<c0259870>] (ksys_write+0x40/0x8c)
[<c0259870>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed55ffa8 to 0xed55fff0)
...

Fixes: 01c10880 ("usb: dwc3: gadget: synchronize_irq dwc irq in suspend")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 54f37f56 ]

Some function drivers queueing more than 128 ISOC requests at a time.
To avoid "descriptor chain full" cases, increasing descriptors count
from MAX_DMA_DESC_NUM_GENERIC to MAX_DMA_DESC_NUM_HS_ISOC for ISOC's
only.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 16ec5dfe ]

On kbl_rt5663_max98927, commit 38a5882e
    ("ASoC: Intel: kbl_rt5663_max98927: Map BTN_0 to KEY_PLAYPAUSE")
    This key pair mapping to play/pause when playing Youtube

The Android 3.5mm Headset jack specification mentions that BTN_0 should
be mapped to KEY_MEDIA, but this is less logical than KEY_PLAYPAUSE,
which has much broader userspace support.

For example, the Chrome OS userspace now supports KEY_PLAYPAUSE to toggle
play/pause of videos and audio, but does not handle KEY_MEDIA.

Furthermore, Android itself now supports KEY_PLAYPAUSE equivalently, as the
new USB headset spec requires KEY_PLAYPAUSE for BTN_0.
https://source.android.com/devices/accessories/headset/usb-headset-spec

The same fix is required on Chrome kbl_da7219_max98357a.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>