What most users care about is "my dev is not working properly".
All low level information should be discovered when activating
the debug traces.

Keep error messages just for the following cases:
- when the SR/FSR report program or erase fails, or attempts of
  modifying a protected sector,
- when the JEDEC ID is not recognized,
- when the resume() call fails,
- when the spi_nor_check() fails.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.

Fixes: f384b352 ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.

Fixes: 59451e12 ("mtd: spi-nor: change return value of read/write")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Print identifying information about struct device.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Constify the data to write to the Status Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

In case the write of the first byte failed, retlen was incorrectly
incremented to *retlen += actual; on the exit path. retlen should be
incremented when actual data was written to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Drop the error messages from the callers, since the callees
already print an error message in case of failure.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Let the callers pass the pointer to the DMA-able buffer where
the value of the Configuration Register will be written. This way we
avoid the casts between int and u8, which can be confusing.

Callers stop compare the return value of spi_nor_read_cr() with negative,
spi_nor_read_cr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Let the callers pass the pointer to the DMA-able buffer where
the value of the Flag Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.

Caller stops compare the return value of spi_nor_read_fsr() with negative,
spi_nor_read_fsr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Let the callers pass the pointer to the DMA-able buffer where
the value of the Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.

Callers stop compare the return value of spi_nor_read_sr() with negative,
spi_nor_read_sr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Do not overwrite the error numbers received the Register Operations
methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

ret is already of type int.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

spi_mem_exec_op()
nor->controller_ops->write_reg()
nor->controller_ops->read_reg()
spi_nor_wait_till_ready()
Return 0 on success, -errno otherwise.

Stop compare with negative and compare with zero in all the register
operations methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Group all register methods up in the file, to avoid forward
declarations.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Two new lines, one after another, drop one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

All the core functions should begin with "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

n_tx was never used, drop it. Replace 'const u8 *txbuf' with 'u8 opcode',
to comply with the SPI NOR int (*read_reg)() method. The 'const'
qualifier has no meaning for parameters passed by value, drop it.
Going furher, the opcode was passed to cqspi_calc_rdreg() and never used,
drop it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Move all SPI NOR controller driver specific ops in a dedicated
structure. 'struct spi_nor' becomes lighter.

Use size_t for lengths in 'int (*write_reg)()' and 'int (*read_reg)()'.
Rename wite/read_buf to buf, the name of the functions are
suggestive enough. Constify buf in int (*write_reg). Comply with these
changes in the SPI NOR controller drivers.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

The pointer to 'struct spi_nor' is kzalloc'ed above in the code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

Tested on HiWiFi C526A

Datasheet is available at:
http://www.xinyahong.com/upLoad/product/month_1411/201411201256018276.pdfSigned-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Now that SPI flash controllers without a software sequencer are
supported, it's trivial to add support for CNL and its PCI ID.

Values from https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/300-series-chipset-pch-datasheet-vol-2.pdfSigned-off-by: Jethro Beekman <jethro@fortanix.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Some flash controllers don't have a software sequencer. Avoid
configuring the register addresses for it, and double check
everywhere that its not accidentally trying to be used.

Every use of `sregs` is now guarded by a check of `sregs` or
`swseq_reg`. The check might be done in the calling function.
Signed-off-by: Jethro Beekman <jethro@fortanix.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Merge tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull more Kbuild fixes from Masahiro Yamada:

 - fix a bashism of setlocalversion

 - do not use the too new --sort option of tar

* tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kheaders: substituting --sort in archive creation
  scripts: setlocalversion: fix a bashism
  kbuild: update comment about KBUILD_ALLDIRS

Pull x86 fixes from Thomas Gleixner:
 "A small set of x86 fixes:

   - Prevent a NULL pointer dereference in the X2APIC code in case of a
     CPU hotplug failure.

   - Prevent boot failures on HP superdome machines by invalidating the
     level2 kernel pagetable entries outside of the kernel area as
     invalid so BIOS reserved space won't be touched unintentionally.

     Also ensure that memory holes are rounded up to the next PMD
     boundary correctly.

   - Enable X2APIC support on Hyper-V to prevent boot failures.

   - Set the paravirt name when running on Hyper-V for consistency

   - Move a function under the appropriate ifdef guard to prevent build
     warnings"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/acpi: Move get_cmdline_acpi_rsdp() under #ifdef guard
  x86/hyperv: Set pv_info.name to "Hyper-V"
  x86/apic/x2apic: Fix a NULL pointer deref when handling a dying cpu
  x86/hyperv: Make vapic support x2apic mode
  x86/boot/64: Round memory hole size up to next PMD page
  x86/boot/64: Make level2_kernel_pgt pages invalid outside kernel area

Pull irq fixes from Thomas Gleixner:
 "A small set of irq chip driver fixes and updates:

   - Update the SIFIVE PLIC interrupt driver to use the fasteoi handler
     to address the shortcomings of the existing flow handling which was
     prone to lose interrupts

   - Use the proper limit for GIC interrupt line numbers

   - Add retrigger support for the recently merged Anapurna Labs Fabric
     interrupt controller to make it complete

   - Enable the ATMEL AIC5 interrupt controller driver on the new
     SAM9X60 SoC"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/sifive-plic: Switch to fasteoi flow
  irqchip/gic-v3: Fix GIC_LINE_NR accessor
  irqchip/atmel-aic5: Add support for sam9x60 irqchip
  irqchip/al-fic: Add support for irq retrigger

Pull hrtimer fixlet from Thomas Gleixner:
 "A single commit annotating the lockcless access to timer->base with
  READ_ONCE() and adding the WRITE_ONCE() counterparts for completeness"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hrtimer: Annotate lockless access to timer->base

Pull stop-machine fix from Thomas Gleixner:
 "A single fix, amending stop machine with WRITE/READ_ONCE() to address
  the fallout of KCSAN"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  stop_machine: Avoid potential race behaviour

Pull networking fixes from David Miller:
 "I was battling a cold after some recent trips, so quite a bit piled up
  meanwhile, sorry about that.

  Highlights:

   1) Fix fd leak in various bpf selftests, from Brian Vazquez.

   2) Fix crash in xsk when device doesn't support some methods, from
      Magnus Karlsson.

   3) Fix various leaks and use-after-free in rxrpc, from David Howells.

   4) Fix several SKB leaks due to confusion of who owns an SKB and who
      should release it in the llc code. From Eric Biggers.

   5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.

   6) Jumbo packets don't work after resume on r8169, as the BIOS resets
      the chip into non-jumbo mode during suspend. From Heiner Kallweit.

   7) Corrupt L2 header during MPLS push, from Davide Caratti.

   8) Prevent possible infinite loop in tc_ctl_action, from Eric
      Dumazet.

   9) Get register bits right in bcmgenet driver, based upon chip
      version. From Florian Fainelli.

  10) Fix mutex problems in microchip DSA driver, from Marek Vasut.

  11) Cure race between route lookup and invalidation in ipv4, from Wei
      Wang.

  12) Fix performance regression due to false sharing in 'net'
      structure, from Eric Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
  net: reorder 'struct net' fields to avoid false sharing
  net: dsa: fix switch tree list
  net: ethernet: dwmac-sun8i: show message only when switching to promisc
  net: aquantia: add an error handling in aq_nic_set_multicast_list
  net: netem: correct the parent's backlog when corrupted packet was dropped
  net: netem: fix error path for corrupted GSO frames
  macb: propagate errors when getting optional clocks
  xen/netback: fix error path of xenvif_connect_data()
  net: hns3: fix mis-counting IRQ vector numbers issue
  net: usb: lan78xx: Connect PHY before registering MAC
  vsock/virtio: discard packets if credit is not respected
  vsock/virtio: send a credit update when buffer size is changed
  mlxsw: spectrum_trap: Push Ethernet header before reporting trap
  net: ensure correct skb->tstamp in various fragmenters
  net: bcmgenet: reset 40nm EPHY on energy detect
  net: bcmgenet: soft reset 40nm EPHYs before MAC init
  net: phy: bcm7xxx: define soft_reset for 40nm EPHY
  net: bcmgenet: don't set phydev->link from MAC
  net: Update address for MediaTek ethernet driver in MAINTAINERS
  ipv4: fix race condition between route lookup and invalidation
  ...

Intel test robot reported a ~7% regression on TCP_CRR tests
that they bisected to the cited commit.

Indeed, every time a new TCP socket is created or deleted,
the atomic counter net->count is touched (via get_net(net)
and put_net(net) calls)

So cpus might have to reload a contended cache line in
net_hash_mix(net) calls.

We need to reorder 'struct net' fields to move @hash_mix
in a read mostly cache line.

We move in the first cache line fields that can be
dirtied often.

We probably will have to address in a followup patch
the __randomize_layout that was added in linux-4.13,
since this might break our placement choices.

Fixes: 355b9855 ("netns: provide pure entropy for net_hash_mix()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.

Fixes: 83c0afae ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam.  Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: netem: fix further issues with packet corruption

This set is fixing two more issues with the netem packet corruption.

First patch (which was previously posted) avoids NULL pointer dereference
if the first frame gets freed due to allocation or checksum failure.
v2 improves the clarity of the code a little as requested by Cong.

Second patch ensures we don't return SUCCESS if the frame was in fact
dropped. Thanks to this commit message for patch 1 no longer needs the
"this will still break with a single-frame failure" disclaimer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.

Fixes: 6071bd1a ("netem: Segment GSO packets on enqueue")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To corrupt a GSO frame we first perform segmentation.  We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.

If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.

Commit 177b8007 ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.

Backlog corrections for parent qdiscs have to be adjusted.

Fixes: 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.

In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.

For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.

Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().

Remove the superfluous module_put().

Fixes: 279f438e ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).

This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.

This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>