1. 14 Feb, 2012 36 commits
    • Thomas Jarosch's avatar
      PCI: Add quirk for still enabled interrupts on Intel Sandy Bridge GPUs · f67fd55f
      Thomas Jarosch authored
      Some BIOS implementations leave the Intel GPU interrupts enabled,
      even though no one is handling them (f.e. i915 driver is never loaded).
      Additionally the interrupt destination is not set up properly
      and the interrupt ends up -somewhere-.
      
      These spurious interrupts are "sticky" and the kernel disables
      the (shared) interrupt line after 100.000+ generated interrupts.
      
      Fix it by disabling the still enabled interrupts.
      This resolves crashes often seen on monitor unplug.
      
      Tested on the following boards:
      - Intel DH61CR: Affected
      - Intel DH67BL: Affected
      - Intel S1200KP server board: Affected
      - Asus P8H61-M LE: Affected, but system does not crash.
        Probably the IRQ ends up somewhere unnoticed.
      
      According to reports on the net, the Intel DH61WW board is also affected.
      
      Many thanks to Jesse Barnes from Intel for helping
      with the register configuration and to Intel in general
      for providing public hardware documentation.
      Signed-off-by: default avatarThomas Jarosch <thomas.jarosch@intra2net.com>
      Tested-by: default avatarCharlie Suffin <charlie.suffin@stratus.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      f67fd55f
    • Arjan van de Ven's avatar
      PCI: Annotate PCI quirks in initcall_debug style · 3209874a
      Arjan van de Ven authored
      While diagnosing some boot time issues on a platform, all that I
      could see in the bootgraph/dmesg was that the system was spending
      a lot of time in applying one or more PCI quirks... which
      was virtually undebuggable.
      
      This patch adds printk's in "initcall_debug" style to the dmesg,
      which are added when the user asks for the initcall_debug
      (the nr one tool to use when debugging boot hangs or boot time issues)
      kernel command line option.
      
      v2: add #includes so quirks can build on non-x86
      Signed-off-by: default avatarArjan van de Ven <arjan@linux.intel.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      3209874a
    • Danny Kukawka's avatar
      PCI hotplug: cpcihp: fix debug module parameter to be bool · 309c6651
      Danny Kukawka authored
      Fix debug variable from module parameter to be really bool to
      fix 'warning: return from incompatible pointer type'.
      Acked-by: default avatarScott Murray <scott@spiteful.org>
      Signed-off-by: default avatarDanny Kukawka <danny.kukawka@bisect.de>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      309c6651
    • Kay, Allen M's avatar
      PCI: check for pci bar restore completion and retry · 26f41062
      Kay, Allen M authored
      On some OEM systems, pci_restore_state() is called while FLR has not yet
      completed.  As a result, PCI BAR register restore is not successful.  This fix
      reads back the restored value and compares it with saved value and re-tries 10
      times before giving up.
      Signed-off-by: default avatarJean Guyader <jean.guyader@eu.citrix.com>
      Signed-off-by: default avatarEric Chanudet <eric.chanudet@citrix.com>
      Signed-off-by: default avatarAllen Kay <allen.m.kay@intel.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      26f41062
    • Yinghai Lu's avatar
      PCI: pciehp: Disable/enable link during slot power off/on · 2debd928
      Yinghai Lu authored
      On a system with a repeater on the system board to support gen2 hotplug,
      we found that when an ExpressModule is removed from some slots,
      /var/log/messages will be full of "card present/not present" warnings.
      
      It turns out the root complex is continually trying to train the link to
      the repeater because the repeater has not been reset.
      
      This patch will disable the link at removal time to allow the repeater
      to be reset properly.  This also prevents a potential AER message at
      removal time.
      
      Also, when testing hotplug on a system under development, we found if we
      boot the system without an EM installed, and later hot-add an EM, it
      does not work with Linux, but another OS is ok.  The root cause is that
      BIOS left link disabled when slot was empty at boot time, and other OS
      is modifying the link disable bit in link ctrl during power on/off.
      
      So we should do the same thing to disable/enable link during power off/on.
      
      -v2: check link DLLA bit instead of 100ms waiting.
           Separate link disable/enable functions to another patch.
      Signed-off-by: default avatarYinghai Lu <yinghai.lu@oracle.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      2debd928
    • Yinghai Lu's avatar
      PCI: pciehp: Add Disable/enable link functions · 7f822999
      Yinghai Lu authored
      Will use it during power off/on of slots
      Signed-off-by: default avatarYinghai Lu <yinghai.lu@oracle.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      7f822999
    • Yinghai Lu's avatar
      PCI: pciehp: Add pcie_wait_link_not_active() · bffe4f72
      Yinghai Lu authored
      Will use it for link disable status checking.
      Signed-off-by: default avatarYinghai Lu <yinghai.lu@oracle.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      bffe4f72
    • Yinghai Lu's avatar
      PCI: pciehp: make check_link_active more helpful · 4e2ce405
      Yinghai Lu authored
      A few changes:
        - remove the 'inline' and let the complier decide
        - return a bool to indicate whether the link was active
        - add a debug message to indicate link state when it beocmes active
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      4e2ce405
    • Yinghai Lu's avatar
      PCI: pciehp: replace unconditional sleep with config space access check · 2f5d8e4f
      Yinghai Lu authored
      During reviewing
      |	PCI: pciehp: wait 1000 ms before Link Training check
      Linus said:
      >...
      > That's a *long* time, and it's irritating to the user. It makes the
      > user think "the machine is slow".
      >...
      > And quite frankly, an unconditional one-second delay here seems bad.
      >Two seconds was unacceptable, one second is just bad.
      
      Try to access the pci conf of a pci device that is supposed to show up
      in 1s.  If we can read back a valid vendor/device id, we can return
      early.
      
      Related discussion could be found:
      	https://lkml.org/lkml/2011/12/6/339
      
      -v2: seperate code to pci_bus_read_dev_vendor_id() from pci_scan_device()
          and reuse it from pciehp code. Suggested by Matthew Wilcox.
      -v3: According to Kenj, don't use array in stack, and don't wait too long
          for crs, also return fail status if not found.
          Also separate pci_bus_dev_read_vendor_id() change to another patch.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      2f5d8e4f
    • Yinghai Lu's avatar
      PCI: Separate pci_bus_read_dev_vendor_id from pci_scan_device · efdc87da
      Yinghai Lu authored
      We can reuse it for pciehp probing.
      
      -v2: according to Kenji, fix crs timeout checking, and export the function
           for later use when pciehp is compiled as a module.
      Suggested-by: default avatarMatthew Wilcox <matthew@wil.cx>
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      efdc87da
    • Yinghai Lu's avatar
      PCI: make sriov work with hotplug remove · ac205b7b
      Yinghai Lu authored
      When hot removing a pci express module that has a pcie switch and supports
      SRIOV, we got:
      
      [ 5918.610127] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 1
      [ 5918.615779] pciehp 0000:80:02.2:pcie04: Attention button interrupt received
      [ 5918.622730] pciehp 0000:80:02.2:pcie04: Button pressed on Slot(3)
      [ 5918.629002] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 1f9
      [ 5918.637416] pciehp 0000:80:02.2:pcie04: PCI slot #3 - powering off due to button press.
      [ 5918.647125] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 10
      [ 5918.653039] pciehp 0000:80:02.2:pcie04: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
      [ 5918.661229] pciehp 0000:80:02.2:pcie04: pciehp_set_attention_status: SLOTCTRL a8 write cmd c0
      [ 5924.667627] pciehp 0000:80:02.2:pcie04: Disabling domain:bus:device=0000:b0:00
      [ 5924.674909] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 2f9
      [ 5924.683262] pciehp 0000:80:02.2:pcie04: pciehp_unconfigure_device: domain:bus:dev = 0000:b0:00
      [ 5924.693976] libfcoe_device_notification: NETDEV_UNREGISTER eth6
      [ 5924.764979] libfcoe_device_notification: NETDEV_UNREGISTER eth14
      [ 5924.873539] libfcoe_device_notification: NETDEV_UNREGISTER eth15
      [ 5924.995209] libfcoe_device_notification: NETDEV_UNREGISTER eth16
      [ 5926.114407] sxge 0000:b2:00.0: PCI INT A disabled
      [ 5926.119342] BUG: unable to handle kernel NULL pointer dereference at (null)
      [ 5926.127189] IP: [<ffffffff81353a3b>] pci_stop_bus_device+0x33/0x83
      [ 5926.133377] PGD 0
      [ 5926.135402] Oops: 0000 [#1] SMP
      [ 5926.138659] CPU 2
      [ 5926.140499] Modules linked in:
      ...
      [ 5926.143754]
      [ 5926.275823] Call Trace:
      [ 5926.278267]  [<ffffffff81353a38>] pci_stop_bus_device+0x30/0x83
      [ 5926.284180]  [<ffffffff81353af4>] pci_remove_bus_device+0x1a/0xba
      [ 5926.290264]  [<ffffffff81366311>] pciehp_unconfigure_device+0x110/0x17b
      [ 5926.296866]  [<ffffffff81365dd9>] ? pciehp_disable_slot+0x188/0x188
      [ 5926.303123]  [<ffffffff81365d6f>] pciehp_disable_slot+0x11e/0x188
      [ 5926.309206]  [<ffffffff81365e68>] pciehp_power_thread+0x8f/0xe0
      ...
      
       +-[0000:80]-+-00.0-[81-8f]--
       |           +-01.0-[90-9f]--
       |           +-02.0-[a0-af]--
       |           +-02.2-[b0-bf]----00.0-[b1-b3]--+-02.0-[b2]--+-00.0 Device
       |           |                               |            +-00.1 Device
       |           |                               |            +-00.2 Device
       |           |                               |            \-00.3 Device
       |           |                               \-03.0-[b3]--+-00.0 Device
       |           |                                            +-00.1 Device
       |           |                                            +-00.2 Device
       |           |                                            \-00.3 Device
      
      root complex: 80:02.2
      pci express modules: have pcie switch and are listed as b0:00.0, b1:02.0 and b1:03.0.
      end devices  are b2:00.0 and b3.00.0.
      VFs are: b2:00.1,... b2:00.3, and b3:00.1,...,b3:00.3
      
      Root cause: when doing pci_stop_bus_device() with phys fn, it will stop
      virt fn and remove the fn, so
      	list_for_each_safe(l, n, &bus->devices)
      will have problem to refer freed n that is pointed to vf entry.
      
      Solution is just replacing list_for_each_safe() with
      list_for_each_prev_safe().  This will make sure we can get valid n pointer
      to PF instead of the freed VF pointer (because newly added devices are
      inserted to the bus->devices list tail).
      
      During reviewing the patch, Bjorn said:
      |   The PCI hot-remove path calls pci_stop_bus_devices() via
      |   pci_remove_bus_device().
      |
      |   pci_stop_bus_devices() traverses the bus->devices list (point A below),
      |   stopping each device in turn, which calls the driver remove() method.  When
      |   the device is an SR-IOV PF, the driver calls pci_disable_sriov(), which
      |   also uses pci_remove_bus_device() to remove the VF devices from the
      |   bus->devices list (point B).
      |
      |       pci_remove_bus_device
      |         pci_stop_bus_device
      |           pci_stop_bus_devices(subordinate)
      |             list_for_each(bus->devices)             <-- A
      |               pci_stop_bus_device(PF)
      |                 ...
      |                   driver->remove
      |                     pci_disable_sriov
      |                       ...
      |                         pci_remove_bus_device(VF)
      |                             <remove from bus_list>  <-- B
      |
      |   At B, we're changing the same list we're iterating through at A, so when
      |   the driver remove() method returns, the pci_stop_bus_devices() iterator has
      |   a pointer to a list entry that has already been freed.
      
      Discussion thread can be found : https://lkml.org/lkml/2011/10/15/141
      				 https://lkml.org/lkml/2012/1/23/360
      
      -v5: According to Linus to make remove more robust, Change to
           list_for_each_prev_safe instead. That is more reasonable, because
           those devices are added to tail of the list before.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      ac205b7b
    • Yinghai Lu's avatar
      PCI: remove add_to_failed_list() · 67cc7e26
      Yinghai Lu authored
      Only one user; just use add_to_list instead.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      67cc7e26
    • Yinghai Lu's avatar
      PCI: add debug print out for add_size · b592443d
      Yinghai Lu authored
      For use in debugging resource reallocation.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      b592443d
    • Yinghai Lu's avatar
      PCI: make free_list() into a function · bffc56d4
      Yinghai Lu authored
      After merging struct pci_dev_resource_x and pci_dev_resource,
      We can use a function instead of macro now.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      bffc56d4
    • Yinghai Lu's avatar
      PCI: Rename dev_res_x to add_res or fail_res · b9b0bba9
      Yinghai Lu authored
      Linus says don't use dev_res_x because it doesn't communicate anything
      about usage.  Rename them to add_res or fail_res etc according to
      context.
      Suggested-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      b9b0bba9
    • Yinghai Lu's avatar
      PCI: Merge pci_dev_resource_x and pci_dev_resource · 764242a0
      Yinghai Lu authored
      pci_dev_resource_x is a superset of pci_dev_resource and they're just
      temp structs used during resource reallocation.
      
      pci_dev_resource usage is quite limted.
      
      So just use pci_dev_resource_x, and rename it as new pci_dev_resource.
      
      -v2: According to Linus, Separate free_list change to another patch
      Suggested-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      764242a0
    • Yinghai Lu's avatar
      PCI: Replace resource_list with generic list · bdc4abec
      Yinghai Lu authored
      So we can use helper functions for generic list.  This makes the
      resource re-allocation code much more readable.
      
      -v2: Use list_add_tail instead of adding list_insert_before, Pointed out
           by Linus.
      Suggested-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      bdc4abec
    • Yinghai Lu's avatar
      PCI: Move struct resource_list to setup-bus.c · 2934a0de
      Yinghai Lu authored
      No user outside of setup-bus.c now.  Later patches will convert
      resource_list to a regular list.
      Suggested-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      2934a0de
    • Yinghai Lu's avatar
      PCI: Move pdev_sort_resources() to setup-bus.c · 78c3b329
      Yinghai Lu authored
      This allows us to move the definition of struct resource_list to
      setup_bus.c and later convert resource_list to a regular list.
      Suggested-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      78c3b329
    • Yinghai Lu's avatar
      PCI: make re-allocation try harder by reassigning ranges higher in the heirarchy · 19aa7ee4
      Yinghai Lu authored
      On a system with devices that support SRIOV connected to a pcie switch
      to pcie root port:
      
       +-[0000:80]-+-00.0-[81-8f]--
       |           +-01.0-[90-9f]--
       |           +-02.0-[a0-af]----00.0-[a1-a3]--+-02.0-[a2]--+-00.0 Oracle Corporation Device 207a
       |           |                               \-03.0-[a3]--+-00.0 Oracle Corporation Device 207a
       |           +-02.2-[b0-bf]----00.0-[b1-b3]--+-02.0-[b2]--+-00.0 Oracle Corporation Device 207a
       |           |                               \-03.0-[b3]--+-00.0 Oracle Corporation Device 207a
      
      When the BIOS does not assign resources for SRIOV BARs, kernel pci
      reallocation only goes up one bridge and then gives up, failing to to
      get resources for all sSRIOV BARs, even though the range is large enough
      in the peer root bus.
      
      Specifically, only the bridge at the a1:02.0 level has its resources
      cleared and reallocated.  The kernel does not go up to clear the bridge
      at the 80:02.0 level.
      
      To make it go to upper levels, during retry, we need to treat "good to have"
      resources as "must have".
      
      Only on the last try will we treat good to have resources as optional.
      At that time, parent bridge resources will already have been released so
      we'll have a chance to get everything assigned with must_have plus
      good_to_have for all child devices.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      19aa7ee4
    • Yinghai Lu's avatar
      PCI: Make pci_rescan_bus handle add_list · 9b03088f
      Yinghai Lu authored
      This allows us to allocate resources to hotplug bridges during
      remove/rescan.
      
      We need to move the function to setup-bus.c so it can use
      __pci_bus_size_bridges and __pci_bus_assign_resources directly to take
      the add_list resource tracking list.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      9b03088f
    • Yinghai Lu's avatar
      PCI: Make rescan bus increase bridge resource size if needed · 2f320521
      Yinghai Lu authored
      Current rescan will not touch bridge MMIO and IO.
      
      Try to reuse pci_assign_unassigned_bridge_resources(bridge) to update bridge
      resources, if child devices need more resources.
      
      Only do that for bridges whose children are all removed already; i.e. don't
      release resources that could already be in use by drivers on child devices.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      2f320521
    • Yinghai Lu's avatar
      PCI: Use add_list in pcie hotplug path. · 8424d759
      Yinghai Lu authored
      We need add size for hot plug path when pluging in hotplug chassis
      without cards.
      
      -v2: change descriptions. make it applicable after "pci: Check bridge
           resources after resource allocation."
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      8424d759
    • Yinghai Lu's avatar
      PCI: try to assign required+option size first · 3e6e0d80
      Yinghai Lu authored
      We found reassignment can not find a range for one resource, even if the
      total available range is large enough.
      
      bridge b1:02.0 will need 2M+3M
      bridge b1:03.0 will need 2M+3M
      
      so bridge b0:00.0 will get assigned: 4M : [f8000000-f83fffff]
         later is reassigned to 10M : [f8000000-f9ffffff]
      
      b1:02.0 is assigned to 2M : [f8000000-f81fffff]
      b1:03.0 is assigned to 2M : [f8200000-f83fffff]
      
      After that b1:03.0 get chance to be reassigned to [f8200000-f86fffff],
      but b1:02.0 will not have chance to expand, because b1:03.0 is using in
      middle one.
      
      [  187.911401] pci 0000:b1:02.0: bridge window [mem 0x00100000-0x002fffff] to [bus b2-b2] add_size 300000
      [  187.920764] pci 0000:b1:03.0: bridge window [mem 0x00100000-0x002fffff] to [bus b3-b3] add_size 300000
      [  187.930129] pci 0000:b1:02.0: [mem 0x00100000-0x002fffff] get_res_add_size  add_size 300000
      [  187.938500] pci 0000:b1:03.0: [mem 0x00100000-0x002fffff] get_res_add_size  add_size 300000
      [  187.946857] pci 0000:b0:00.0: bridge window [mem 0x00100000-0x004fffff] to [bus b1-b3] add_size 600000
      [  187.956206] pci 0000:b0:00.0: BAR 14: assigned [mem 0xf8000000-0xf83fffff]
      [  187.963102] pci 0000:b0:00.0: BAR 15: assigned [mem 0xf5000000-0xf51fffff pref]
      [  187.970434] pci 0000:b0:00.0: BAR 14: reassigned [mem 0xf8000000-0xf89fffff]
      [  187.977497] pci 0000:b1:02.0: BAR 14: assigned [mem 0xf8000000-0xf81fffff]
      [  187.984383] pci 0000:b1:02.0: BAR 15: assigned [mem 0xf5000000-0xf50fffff pref]
      [  187.991695] pci 0000:b1:03.0: BAR 14: assigned [mem 0xf8200000-0xf83fffff]
      [  187.998576] pci 0000:b1:03.0: BAR 15: assigned [mem 0xf5100000-0xf51fffff pref]
      [  188.005888] pci 0000:b1:03.0: BAR 14: reassigned [mem 0xf8200000-0xf86fffff]
      [  188.012939] pci 0000:b1:02.0: BAR 14: can't assign mem (size 0x200000)
      [  188.019471] pci 0000:b1:02.0: failed to add 300000 to res=[mem 0xf8000000-0xf81fffff]
      [  188.027326] pci 0000:b2:00.0: reg 184: [mem 0x00000000-0x00003fff 64bit]
      [  188.034071] pci 0000:b2:00.0: reg 18c: [mem 0x00000000-0x000fffff 64bit]
      [  188.040795] pci 0000:b2:00.0: BAR 2: assigned [mem 0xf8000000-0xf80fffff 64bit]
      [  188.048119] pci 0000:b2:00.0: BAR 2: set to [mem 0xf8000000-0xf80fffff 64bit] (PCI address [0xf8000000-0xf80fffff])
      [  188.058550] pci 0000:b2:00.0: BAR 6: assigned [mem 0xf5000000-0xf50fffff pref]
      [  188.065802] pci 0000:b2:00.0: BAR 0: assigned [mem 0xf8100000-0xf8103fff 64bit]
      [  188.073125] pci 0000:b2:00.0: BAR 0: set to [mem 0xf8100000-0xf8103fff 64bit] (PCI address [0xf8100000-0xf8103fff])
      [  188.083596] pci 0000:b2:00.0: reg 18c: [mem 0x00000000-0x000fffff 64bit]
      [  188.090310] pci 0000:b2:00.0: BAR 9: can't assign mem (size 0x300000)
      [  188.096773] pci 0000:b2:00.0: reg 184: [mem 0x00000000-0x00003fff 64bit]
      [  188.103479] pci 0000:b2:00.0: BAR 7: assigned [mem 0xf8104000-0xf810ffff 64bit]
      [  188.110801] pci 0000:b2:00.0: BAR 7: set to [mem 0xf8104000-0xf810ffff 64bit] (PCI address [0xf8104000-0xf810ffff])
      [  188.121256] pci 0000:b1:02.0: PCI bridge to [bus b2-b2]
      [  188.126512] pci 0000:b1:02.0:   bridge window [mem 0xf8000000-0xf81fffff]
      [  188.133328] pci 0000:b1:02.0:   bridge window [mem 0xf5000000-0xf50fffff pref]
      [  188.140608] pci 0000:b3:00.0: reg 184: [mem 0x00000000-0x00003fff 64bit]
      [  188.147341] pci 0000:b3:00.0: reg 18c: [mem 0x00000000-0x000fffff 64bit]
      [  188.154076] pci 0000:b3:00.0: BAR 2: assigned [mem 0xf8200000-0xf82fffff 64bit]
      [  188.161417] pci 0000:b3:00.0: BAR 2: set to [mem 0xf8200000-0xf82fffff 64bit] (PCI address [0xf8200000-0xf82fffff])
      [  188.171865] pci 0000:b3:00.0: BAR 6: assigned [mem 0xf5100000-0xf51fffff pref]
      [  188.179090] pci 0000:b3:00.0: BAR 0: assigned [mem 0xf8300000-0xf8303fff 64bit]
      [  188.186431] pci 0000:b3:00.0: BAR 0: set to [mem 0xf8300000-0xf8303fff 64bit] (PCI address [0xf8300000-0xf8303fff])
      [  188.196884] pci 0000:b3:00.0: reg 18c: [mem 0x00000000-0x000fffff 64bit]
      [  188.203591] pci 0000:b3:00.0: BAR 9: assigned [mem 0xf8400000-0xf86fffff 64bit]
      [  188.210909] pci 0000:b3:00.0: BAR 9: set to [mem 0xf8400000-0xf86fffff 64bit] (PCI address [0xf8400000-0xf86fffff])
      [  188.221379] pci 0000:b3:00.0: reg 184: [mem 0x00000000-0x00003fff 64bit]
      [  188.228089] pci 0000:b3:00.0: BAR 7: assigned [mem 0xf8304000-0xf830ffff 64bit]
      [  188.235407] pci 0000:b3:00.0: BAR 7: set to [mem 0xf8304000-0xf830ffff 64bit] (PCI address [0xf8304000-0xf830ffff])
      [  188.245843] pci 0000:b1:03.0: PCI bridge to [bus b3-b3]
      [  188.251107] pci 0000:b1:03.0:   bridge window [mem 0xf8200000-0xf86fffff]
      [  188.257922] pci 0000:b1:03.0:   bridge window [mem 0xf5100000-0xf51fffff pref]
      [  188.265180] pci 0000:b0:00.0: PCI bridge to [bus b1-b3]
      [  188.270443] pci 0000:b0:00.0:   bridge window [mem 0xf8000000-0xf89fffff]
      [  188.277250] pci 0000:b0:00.0:   bridge window [mem 0xf5000000-0xf51fffff pref]
      [  188.284512] pcieport 0000:80:02.2: PCI bridge to [bus b0-bf]
      [  188.290184] pcieport 0000:80:02.2:   bridge window [io  0xa000-0xbfff]
      [  188.296735] pcieport 0000:80:02.2:   bridge window [mem 0xf8000000-0xf8ffffff]
      [  188.303963] pcieport 0000:80:02.2:   bridge window [mem 0xf5000000-0xf5ffffff 64bit pref]
      
      Thus b2:00.0 BAR 9 does not get assigned...
      
      root cause:
      b1:02.0 can not be added more range, because b1:03.0 is just after it;
      no space between the required ranges.
      
      Solution:
      Try to assign required + optional all together at first, and if that
      fails, try again with just the required resources.
      
      -v2: seperate add_to_list change() to another patch according to Jesse.
           seperate get_res_add_size() moving to another patch according to Jesse.
           add !realloc_head->next check if the list is empty to bail early
           according to Jesse.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      3e6e0d80
    • Yinghai Lu's avatar
      PCI: Move get_res_add_size() function · 1c372353
      Yinghai Lu authored
      Need to call it from __assign_resources_sorted() later and we'd like to
      avoid a forward declaraion.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      1c372353
    • Yinghai Lu's avatar
      PCI: Make add_to_list() return status · ef62dfef
      Yinghai Lu authored
      Will be used for resource_list_x duplication when trying
      requested+optional at first.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      ef62dfef
    • Yinghai Lu's avatar
      PCI : Calculate right add_size · a4ac9fea
      Yinghai Lu authored
      During debug of one SRIOV enabled hotplug device, we found found that
      add_size is not passed properly.
      
      The device has devices under two level bridges:
      
       +-[0000:80]-+-00.0-[81-8f]--
       |           +-01.0-[90-9f]--
       |           +-02.0-[a0-af]----00.0-[a1-a3]--+-02.0-[a2]--+-00.0  Oracle Corporation Device
       |           |                               \-03.0-[a3]--+-00.0  Oracle Corporation Device
      
      Which means later the parent bridge will not try to add a big enough range:
      
      [  557.455077] pci 0000:a0:00.0: BAR 14: assigned [mem 0xf9000000-0xf93fffff]
      [  557.461974] pci 0000:a0:00.0: BAR 15: assigned [mem 0xf6000000-0xf61fffff pref]
      [  557.469340] pci 0000:a1:02.0: BAR 14: assigned [mem 0xf9000000-0xf91fffff]
      [  557.476231] pci 0000:a1:02.0: BAR 15: assigned [mem 0xf6000000-0xf60fffff pref]
      [  557.483582] pci 0000:a1:03.0: BAR 14: assigned [mem 0xf9200000-0xf93fffff]
      [  557.490468] pci 0000:a1:03.0: BAR 15: assigned [mem 0xf6100000-0xf61fffff pref]
      [  557.497833] pci 0000:a1:03.0: BAR 14: can't assign mem (size 0x200000)
      [  557.504378] pci 0000:a1:03.0: failed to add optional resources res=[mem 0xf9200000-0xf93fffff]
      [  557.513026] pci 0000:a1:02.0: BAR 14: can't assign mem (size 0x200000)
      [  557.519578] pci 0000:a1:02.0: failed to add optional resources res=[mem 0xf9000000-0xf91fffff]
      
      It turns out we did not calculate size1 properly.
      
      static resource_size_t calculate_memsize(resource_size_t size,
                      resource_size_t min_size,
                      resource_size_t size1,
                      resource_size_t old_size,
                      resource_size_t align)
      {
              if (size < min_size)
                      size = min_size;
              if (old_size == 1 )
                      old_size = 0;
              if (size < old_size)
                      size = old_size;
              size = ALIGN(size + size1, align);
              return size;
      }
      
      We should not pass add_size with min_size in calculate_memsize since
      that will make add_size not contribute final add_size.
      
      So just pass add_size with size1 to calculate_memsize().
      
      With this change, we should have chance to remove extra addon in
      pci_reassign_resource.
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      a4ac9fea
    • Masanari Iida's avatar
      PCI: Fix typo in setup-res.c · 0dea210b
      Masanari Iida authored
      Correct spelling "resouce" to "resource" in
      dricers/pci/setup-res.c
      Signed-off-by: default avatarMasanari Iida <standby24x7@gmail.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      0dea210b
    • Bjorn Helgaas's avatar
      x86/PCI: don't fall back to defaults if _CRS has no apertures · 316d86fe
      Bjorn Helgaas authored
      Host bridges that lead to things like the Uncore need not have any
      I/O port or MMIO apertures.  For example, in this case:
      
          ACPI: PCI Root Bridge [UNC1] (domain 0000 [bus ff])
          PCI: root bus ff: using default resources
          PCI host bridge to bus 0000:ff
          pci_bus 0000:ff: root bus resource [io  0x0000-0xffff]
          pci_bus 0000:ff: root bus resource [mem 0x00000000-0x3fffffffffff]
      
      we should not pretend those default resources are available on bus ff.
      
      CC: Yinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarBjorn Helgaas <bhelgaas@google.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      316d86fe
    • Konrad Rzeszutek Wilk's avatar
      xen/pciback: Support pci_reset_function, aka FLR or D3 support. · 11608318
      Konrad Rzeszutek Wilk authored
      We use the __pci_reset_function_locked to perform the action.
      Also on attaching ("bind") and detaching ("unbind") we save and
      restore the configuration states. When the device is disconnected
      from a guest we use the "pci_reset_function" to also reset the
      device before being passed to another guest.
      Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      11608318
    • Konrad Rzeszutek Wilk's avatar
      PCI: Introduce __pci_reset_function_locked to be used when holding device_lock. · 6fbf9e7a
      Konrad Rzeszutek Wilk authored
      The use case of this is when a driver wants to call FLR when a device
      is attached to it using the SysFS "bind" or "unbind" functionality.
      
      The call chain when a user does "bind" looks as so:
      
       echo "0000:01.07.0" > /sys/bus/pci/drivers/XXXX/bind
      
      and ends up calling:
        driver_bind:
          device_lock(dev);  <=== TAKES LOCK
          XXXX_probe:
               .. pci_enable_device()
               ...__pci_reset_function(), which calls
                       pci_dev_reset(dev, 0):
                              if (!0) {
                                      device_lock(dev) <==== DEADLOCK
      
      The __pci_reset_function_locked function allows the the drivers
      'probe' function to call the "pci_reset_function" while still holding
      the driver mutex lock.
      Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      6fbf9e7a
    • Julia Lawall's avatar
      PCI: drivers/pci/hotplug/ibmphp_ebda.c: add missing iounmap · 8f0cdddc
      Julia Lawall authored
      Add missing iounmap in error handling code, in a case where the function
      already preforms iounmap on some other execution path.
      
      A simplified version of the semantic match that finds this problem is as
      follows: (http://coccinelle.lip6.fr/)
      
      // <smpl>
      @@
      expression e;
      statement S,S1;
      int ret;
      @@
      e = \(ioremap\|ioremap_nocache\)(...)
      ... when != iounmap(e)
      if (<+...e...+>) S
      ... when any
          when != iounmap(e)
      *if (...)
         { ... when != iounmap(e)
           return ...; }
      ... when any
      iounmap(e);
      // </smpl>
      Signed-off-by: default avatarJulia Lawall <Julia.Lawall@lip6.fr>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      8f0cdddc
    • Amos Kong's avatar
      PCI: Can continually add funcs after adding func0 · f382a086
      Amos Kong authored
      Boot up a KVM guest, and hotplug multifunction
      devices(func1,func2,func0,func3) to guest.
      
      for i in 1 2 0 3;do
      qemu-img create /tmp/resize$i.qcow2 1G -f qcow2
      (qemu) drive_add 0x11.$i id=drv11$i,if=none,file=/tmp/resize$i.qcow2
      (qemu) device_add virtio-blk-pci,id=dev11$i,drive=drv11$i,addr=0x11.$i,multifunction=on
      done
      
      In linux kernel, when func0 of the slot is hot-added, the whole
      slot will be marked as 'enabled', then driver will ignore other new
      hotadded funcs.
      But in Win7 & WinXP, we can continaully add other funcs after adding
      func0, all funcs will be added in guest.
      
      drivers/pci/hotplug/acpiphp_glue.c:
      static int acpiphp_check_bridge(struct acpiphp_bridge *bridge)
      {
      ....
              for (slot = bridge->slots; slot; slot = slot->next) {
                      if (slot->flags & SLOT_ENABLED) {
                              acpiphp_disable_slot()
                      else
                              acpiphp_enable_slot()
      ....                              |
      }                                 v
                                  enable_device()
                                        |
                                        v
              //only don't enable slot if func0 is not added
      	list_for_each_entry(func, &slot->funcs, sibling) {
                     ...
              }
             slot->flags |= SLOT_ENABLED; //mark slot to 'enabled'
      
      This patch just make pci driver can continaully add funcs after adding
      func 0. Only mark slot to 'enabled' when all funcs are added.
      
      For pci multifunction hotplug, we can add functions one by one(func 0 is
      necessary), and all functions will be removed in one time.
      Signed-off-by: default avatarAmos Kong <akong@redhat.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      f382a086
    • Myron Stowe's avatar
      x86/PCI: Convert maintaining FW-assigned BIOS BAR values to use a list · 6535943f
      Myron Stowe authored
      This patch converts the underlying maintenance aspects of FW-assigned
      BIOS BAR values from a statically allocated array within struct pci_dev
      to a list of temporary, stand alone, entries.
      Signed-off-by: default avatarMyron Stowe <myron.stowe@redhat.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      6535943f
    • Myron Stowe's avatar
      x86/PCI: Infrastructure to maintain a list of FW-assigned BIOS BAR values · 925845bd
      Myron Stowe authored
      Commit 58c84eda introduced functionality to try and reinstate the
      original BIOS BAR addresses of a PCI device when normal resource
      assignment attempts fail.  To keep track of the BIOS BAR addresses,
      struct pci_dev was augmented with an array to hold the BAR addresses
      of the PCI device: 'resource_size_t fw_addr[DEVICE_COUNT_RESOURCE]'.
      
      The reinstatement of BAR addresses is an uncommon event leaving the
      'fw_addr' array unused under normal circumstances.  This functionality
      is also currently architecture specific with an implementation limited
      to x86.  As the use of struct pci_dev is so prevalent, having the
      'fw_addr' array residing within such seems somewhat wasteful.
      
      This patch introduces a stand alone data structure and interfacing
      routines for maintaining a list of FW-assigned BIOS BAR value entries.
      Signed-off-by: default avatarMyron Stowe <myron.stowe@redhat.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      925845bd
    • Myron Stowe's avatar
      PCI: Fix starting basis for resource requests · 351fc6d1
      Myron Stowe authored
      pci_revert_fw_address() is used to reinstate a PCI device's original
      FW-assigned BIOS BAR value(s) if normal resource assignment fails.
      
      When attempting to reinstate an address, the point within the resource
      tree from which to attempt the new resource request should be the parent
      resource corresponding to the device, not the base of the resource tree
      (ioport_resource or iomem_resource).  For PCI devices this would
      typically be the resource corresponding to the upstream PCI host bridge
      or P2P bridge aperture.
      
      This patch sets the point within the resource tree to attempt a new
      resource assignment request to the PCI device's parent resource and only
      if that fails does it fall back to the base ioport_resource or
      iomem_resource.
      Signed-off-by: default avatarMyron Stowe <myron.stowe@redhat.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      351fc6d1
  2. 10 Feb, 2012 3 commits
    • Yinghai Lu's avatar
      PCI: Fix pci cardbus removal · 3682a394
      Yinghai Lu authored
      During test busn_res allocation with cardbus, found pci card removal is not
      working anymore, and it turns out it is broken by:
      
      |commit 79cc9601
      |Date:   Tue Nov 22 21:06:53 2011 -0800
      |
      |    PCI: Only call pci_stop_bus_device() one time for child devices at remove
      
      The above changed the behavior of pci_remove_behind_bridge that
      yenta_cardbus depended on.  So restore the old behavoir of
      pci_remove_behind_bridge (which requires stopping and removing of all
      devices) by:
      
      1. rename pci_remove_behind_bridge to __pci_remove_behind_bridge, and let
         __pci_remove_bus_device() call it instead.
      2. add pci_stop_behind_bridge that will stop devices behind a bridge
      3. add back pci_remove_behind_bridge that will stop and remove devices
         under bridge.
      
      -v2: update commit description a little bit.
      Tested-by: default avatarDominik Brodowski <linux@dominikbrodowski.net>
      Signed-off-by: default avatarYinghai Lu <yinghai@kernel.org>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      3682a394
    • Vaidyanathan Srinivasan's avatar
      PCI: set pci sriov page size before reading SRIOV BAR · 8161fe91
      Vaidyanathan Srinivasan authored
      For an SRIOV device, PCI_SRIOV_SYS_PGSIZE should be set before
      the PCI_SRIOV_BAR are queried.  The sys pagesize defaults to 4k,
      so this change is required on powerpc box with 64k base page size.
          
      This is a regression caused due to moving SRIOV init to sriov_enable().
          
      | commit afd24ece
      | Author: Ram Pai <linuxram@us.ibm.com>
          
      | PCI: delay configuration of SRIOV capability
      | The SRIOV capability, namely page size and total_vfs of a device are
      | configured during enumeration phase of the device.  This can potentially
      | interfere with the PCI operations of the platform, if the IOV capability
      | of the device is not enabled.
      Signed-off-by: default avatarVaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
      Acked-by: default avatarRam Pai <linuxram@us.ibm.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      8161fe91
    • Yinghai Lu's avatar
      PCI: workaround hard-wired bus number V2 · 71f6bd4a
      Yinghai Lu authored
      Fixes PCI device detection on IBM xSeries IBM 3850 M2 / x3950 M2
      when using ACPI resources (_CRS).
      This is default, a manual workaround (without this patch)
      would be pci=nocrs boot param.
      
      V2: Add dev_warn if the workaround is hit. This should reveal
      how common such setups are (via google) and point to possible
      problems if things are still not working as expected.
      -> Suggested by Jan Beulich.
      
      Cc: stable@vger.kernel.org
      Tested-by: garyhade@us.ibm.com
      Signed-off-by: default avatarYinghai Lu <yinghai.lu@oracle.com>
      Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
      71f6bd4a
  3. 27 Jan, 2012 1 commit
    • Linus Torvalds's avatar
      Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux · acb42a3b
      Linus Torvalds authored
      * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
        gma500: Fix suspend/resume functions
        drm/exynos: fixed pm feature for fimd module.
        MAINTAINERS: added maintainer entry for Exynos DRM Driver.
        drm/exynos: fixed build dependency for DRM_EXYNOS_FIMD
        drm/exynos: fix build dependency for DRM_EXYNOS_HDMI
        drm/exynos: use release_mem_region instead of release_resource
        agp: fix scratch page cleanup
        drm/i915: fixup forcewake spinlock fallout in drpc debugfs function
        drm/i915: debugfs: show semaphore registers also on gen7
        drm/i915: allow userspace forcewake references also on gen7
        drm/i915: Re-enable gen7 RC6 and GPU turbo after resume.
        drm/i915: Correct debugfs printout for RC1e.
        Revert "drm/i915: Work around gen7 BLT ring synchronization issues."
        drm/i915: rip out the HWSTAM missed irq workaround
        drm/i915: paper over missed irq issues with force wake voodoo
        drm/i915: Hold gt_lock across forcewake register reads
        drm/i915: Hold gt_lock during reset
        drm/i915: Move reset forcewake processing to gen6_do_reset
        drm/i915: protect force_wake_(get|put) with the gt_lock
        drm/i915: convert force_wake_get to func pointer in the gpu reset code
        ...
      acb42a3b