Skip to content

L
linux
Switch branch/tag
  1. 30 Jul, 2015 18 commits
  3. 29 Jul, 2015 7 commits
    • Nikolay Aleksandrov's avatar
      bridge: mdb: fix delmdb state in the notification · 7ae90a4f
      Nikolay Aleksandrov authored 
      Since mdb states were introduced when deleting an entry the state was
left as it was set in the delete request from the user which leads to
the following output when doing a monitor (for example):
$ bridge mdb add dev br0 port eth3 grp 239.0.0.1 permanent
(monitor) dev br0 port eth3 grp 239.0.0.1 permanent
$ bridge mdb del dev br0 port eth3 grp 239.0.0.1 permanent
(monitor) dev br0 port eth3 grp 239.0.0.1 temp
^^^
Note the "temp" state in the delete notification which is wrong since
the entry was permanent, the state in a delete is always reported as
"temp" regardless of the real state of the entry.

After this patch:
$ bridge mdb add dev br0 port eth3 grp 239.0.0.1 permanent
(monitor) dev br0 port eth3 grp 239.0.0.1 permanent
$ bridge mdb del dev br0 port eth3 grp 239.0.0.1 permanent
(monitor) dev br0 port eth3 grp 239.0.0.1 permanent

There's one important note to make here that the state is actually not
matched when doing a delete, so one can delete a permanent entry by
stating "temp" in the end of the command, I've chosen this fix in order
not to break user-space tools which rely on this (incorrect) behaviour.

So to give an example after this patch and using the wrong state:
$ bridge mdb add dev br0 port eth3 grp 239.0.0.1 permanent
(monitor) dev br0 port eth3 grp 239.0.0.1 permanent
$ bridge mdb del dev br0 port eth3 grp 239.0.0.1 temp
(monitor) dev br0 port eth3 grp 239.0.0.1 permanent

Note the state of the entry that got deleted is correct in the
notification.
Signed-off-by: default avatarNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: ccb1c31a ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      7ae90a4f
    • Satish Ashok's avatar
      bridge: mcast: give fast leave precedence over multicast router and querier · 544586f7
      Satish Ashok authored 
      When fast leave is configured on a bridge port and an IGMP leave is
received for a group, the group is not deleted immediately if there is
a router detected or if multicast querier is configured.
Ideally the group should be deleted immediately when fast leave is
configured.
Signed-off-by: default avatarSatish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      544586f7
    • Toshiaki Makita's avatar
      bridge: Fix network header pointer for vlan tagged packets · df356d5e
      Toshiaki Makita authored 
      There are several devices that can receive vlan tagged packets with
CHECKSUM_PARTIAL like tap, possibly veth and xennet.
When (multiple) vlan tagged packets with CHECKSUM_PARTIAL are forwarded
by bridge to a device with the IP_CSUM feature, they end up with checksum
error because before entering bridge, the network header is set to
ETH_HLEN (not including vlan header length) in __netif_receive_skb_core(),
get_rps_cpu(), or drivers' rx functions, and nobody fixes the pointer later.

Since the network header is exepected to be ETH_HLEN in flow-dissection
and hash-calculation in RPS in rx path, and since the header pointer fix
is needed only in tx path, set the appropriate network header on forwarding
packets.
Signed-off-by: default avatarToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      df356d5e
    • Alexander Drozdov's avatar
      packet: tpacket_snd(): fix signed/unsigned comparison · dbd46ab4
      Alexander Drozdov authored 
      tpacket_fill_skb() can return a negative value (-errno) which
is stored in tp_len variable. In that case the following
condition will be (but shouldn't be) true:

tp_len > dev->mtu + dev->hard_header_len

as dev->mtu and dev->hard_header_len are both unsigned.

That may lead to just returning an incorrect EMSGSIZE errno
to the user.

Fixes: 52f1454f ("packet: allow to transmit +4 byte in TX_RING slot for VLAN case")
Signed-off-by: default avatarAlexander Drozdov <al.drozdov@gmail.com>
Acked-by: default avatarDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      dbd46ab4
    • Eric Dumazet's avatar
      arp: filter NOARP neighbours for SIOCGARP · 11c91ef9
      Eric Dumazet authored 
      When arp is off on a device, and ioctl(SIOCGARP) is queried,
a buggy answer is given with MAC address of the device, instead
of the mac address of the destination/gateway.

We filter out NUD_NOARP neighbours for /proc/net/arp,
we must do the same for SIOCGARP ioctl.

Tested:

lpaa23:~# ./arp 10.246.7.190
MAC=00:01:e8:22:cb:1d      // correct answer

lpaa23:~# ip link set dev eth0 arp off
lpaa23:~# cat /proc/net/arp   # check arp table is now 'empty'
IP address       HW type     Flags       HW address    Mask     Device
lpaa23:~# ./arp 10.246.7.190
MAC=00:1a:11:c3:0d:7f   // buggy answer before patch (this is eth0 mac)

After patch :

lpaa23:~# ip link set dev eth0 arp off
lpaa23:~# ./arp 10.246.7.190
ioctl(SIOCGARP) failed: No such device or address
Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
Reported-by: default avatarVytautas Valancius <valas@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      11c91ef9
    • David Ward's avatar
      net/ipv4: suppress NETDEV_UP notification on address lifetime update · 865b8042
      David Ward authored 
      This notification causes the FIB to be updated, which is not needed
because the address already exists, and more importantly it may undo
intentional changes that were made to the FIB after the address was
originally added. (As a point of comparison, when an address becomes
deprecated because its preferred lifetime expired, a notification on
this chain is not generated.)

The motivation for this commit is fixing an incompatibility between
DHCP clients which set and update the address lifetime according to
the lease, and a commercial VPN client which replaces kernel routes
in a way that outbound traffic is sent only through the tunnel (and
disconnects if any further route changes are detected via netlink).
Signed-off-by: default avatarDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      865b8042
    • Nikolay Aleksandrov's avatar
      bridge: stp: when using userspace stp stop kernel hello and hold timers · 76b91c32
      Nikolay Aleksandrov authored 
      These should be handled only by the respective STP which is in control.
They become problematic for devices with limited resources with many
ports because the hold_timer is per port and fires each second and the
hello timer fires each 2 seconds even though it's global. While in
user-space STP mode these timers are completely unnecessary so it's better
to keep them off.
Also ensure that when the bridge is up these timers are started only when
running with kernel STP.
Signed-off-by: default avatarSatish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: default avatarNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      76b91c32
  5. 27 Jul, 2015 15 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7