Intel AHCI controllers that also hide NVMe devices in their bar
can't use MSI interrupts, so disable them.
Reported-by: John Loy <john.robert.loy@gmail.com>
Tested-by: John Loy <john.robert.loy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: d684a90d ("ahci: per-port msix support")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Tejun Heo <tj@kernel.org>

Add DT bindings for the onboard SATA controller present on the MediaTek
SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

This adds support the AHCI-compliant Serial ATA controller present
on MediaTek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

The Octeon CF driver basically  open-codes of_property_read_{bool|u32}()
using  of_{find|get}_property() calls in its  probe() method.  Using the
modern DT APIs saves 2 LoCs and 16 bytes of object code (MIPS gcc 3.4.3).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Several legacy devices such as Geode-based Cisco ASA appliances
and DB800 development board do possess CS5536 IDE controller
with different PCI id than existing one. Using pata_generic is
not always feasible as at least DB800 requires MSR quirk from
pata_cs5536 to be used with vendor firmware.
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
CC: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>

The IDE pins are managed by the pin controller, if we want to
use these, we need to ask the pin controller to explicitly enable
them as by default, these pins are used for other business and
most users just rely on the SATA bridge.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

I added a proper pin control driver for the Gemini SoC, so retire
this custom code and rely on the pin controller to set up the pads.

The "IOMUX" which is routing signals between the ATA and SATA
bridge inside of the chip is not about pin control and remains in
place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

The newly introduced ahci_platform_shutdown() method is called during
system shutdown to disable host controller DMA and interrupts in order
to avoid potentially corrupting or otherwise interfering with a new
kernel being started with kexec.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: linux-ide@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

Drop static on a local variable, when the variable is initialized before
any possible use.  Thus, the static has no benefit.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>

@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
 T x@p;
 ... when != x
     when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>

Pull MD fixes from Shaohua Li:

 - raid5-ppl fix by Artur. This one is introduced in this release cycle.

 - raid5 reshape fix by Xiao. This is an old bug and will be added to
   stable.

 - bitmap fix by Guoqing.

* tag 'md/4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  raid5-ppl: use BIOSET_NEED_BVECS when creating bioset
  Raid5 should update rdev->sectors after reshape
  md/bitmap: don't read page from device with Bitmap_sync

Pull rdma fixes from Doug Ledford:
 "First set of -rc fixes for 4.13 cycle:

   - misc iSER fixes

   - namespace fixups

   - fix the fact that IPoIB didn't use the proper API for noio mem allocs

   - rxe driver fixes

   - hns_roce fixes

   - misc core fixes

   - misc IPoIB fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (27 commits)
  IB/core: Allow QP state transition from reset to error
  IB/hns: Fix for checkpatch.pl comment style warnings
  IB/hns: Fix the bug with modifying the MAC address without removing the driver
  IB/hns: Fix the bug with rdma operation
  IB/hns: Fix the bug with wild pointer when destroy rc qp
  IB/hns: Fix the bug of polling cq failed for loopback Qps
  IB/rxe: Set dma_mask and coherent_dma_mask
  IB/rxe: Fix kernel panic from skb destructor
  IB/ipoib: Let lower driver handle get_stats64 call
  IB/core: Add ordered workqueue for RoCE GID management
  IB/mlx5: Clean mr_cache debugfs in case of failure
  IB/core: Remove NOIO QP create flag
  {net, IB}/mlx4: Remove gfp flags argument
  IB/{rdmavt, qib, hfi1}: Remove gfp flags argument
  IB/IPoIB: Convert IPoIB to memalloc_noio_* calls
  IB/IPoIB: Forward MTU change to driver below
  IB: Convert msleep below 20ms to usleep_range
  IB/uverbs: Make use of ib_modify_qp variant to avoid resolving DMAC
  IB/core: Introduce modify QP operation with udata
  IB/core: Don't resolve IP address to the loopback device
  ...

Pull nfsd fix from Bruce Fields:
 "One fix for a problem introduced in the most recent merge window and
  found by Dave Jones and KASAN"

* tag 'nfsd-4.13-1' of git://linux-nfs.org/~bfields/linux:
  nfsd: Fix a memory scribble in the callback channel

Playing with IP-O-IB interface can trigger a warning message:
"ib0: Failed to modify QP to ERROR state" to be logged.
This happens when the QP is in IB_QPS_RESET state and the stack
is trying to transition it to IB_QPS_ERR state in ipoib_ib_dev_stop().

According to the IB spec, Table 91 - "QP State Transition Properties"
it looks like the transition from reset to error is valid:

Transition: Any State to Error
Required Attributes: None
Optional Attributes: None allowed
Actions: Queue processing is stopped. Work Requests pending or in
process are completed in error, when possible.

This patch allows the transition and quiets the message.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch correct the comment style warnings caught by
checkpatch.pl script.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When modified the MAC address used hns_roce_mac function, we release and create
reserved qp again, It is not necessary to use spin_lock_bh and spin_unlock_bh in
handle_en_event, Otherwise, it will occur a error. This patch mainly fixes it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When opcode of work request is RDMA read and write, it
should use rdma_wr to get remote_addr and rkey. This
patch fixes it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When destroyed rc qp, the hr_qp will be used after freed. This patch
will fix it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

In hip06 SoC, RoCE driver creates 8 reserved loopback QPs to
ensure zero wqe when free mr. However, if the enabled phy
port number is less than 6, it will fail in polling cqe with
8 reserved loopback QPs.

In order to solve this problem, the number of loopback Qps
will be adjusted based on the number of enabled phy port.
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The RXE coupled with dummy device causes to the kernel panic attached
below.  The panic happens when ib_register_device tries to set dma_mask
by accessing a NULLed parent device.

The RXE does not actually use DMA, so we can set the dma_mask
to architecture value.

[16240.199689] RIP: 0010:ib_register_device+0x468/0x5a0 [ib_core]
[16240.205289] RSP: 0018:ffffc9000220fc10 EFLAGS: 00010246
[16240.209909] RAX: 0000000000000024 RBX: ffff880220d1a2a8 RCX: 0000000000000000
[16240.212244] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000009
[16240.214385] RBP: ffffc9000220fcb0 R08: 0000000000000000 R09: 000000000000023f
[16240.254465] R10: 0000000000000007 R11: 0000000000000000 R12: 0000000000000000
[16240.259467] R13: 0000000000000000 R14: 0000000000000000 R15: ffff880220d1a2a8
[16240.263314] FS:  00007fd8ecca0740(0000) GS:ffff8802364c0000(0000) knlGS:0000000000000000
[16240.267292] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[16240.273503] CR2: 0000000000000218 CR3: 00000002253ba000 CR4: 00000000000006e0
[16240.277066] Call Trace:
[16240.281836]  ? __kmalloc+0x26f/0x280
[16240.286596]  rxe_register_device+0x297/0x300 [rdma_rxe]
[16240.291377]  rxe_add+0x535/0x5b0 [rdma_rxe]
[16240.297586]  rxe_net_add+0x3e/0xc0 [rdma_rxe]
[16240.302375]  rxe_param_set_add+0x65/0x144 [rdma_rxe]
[16240.307769]  param_attr_store+0x68/0xd0
[16240.311640]  module_attr_store+0x1d/0x30
[16240.316421]  sysfs_kf_write+0x3a/0x50
[16240.317802]  kernfs_fop_write+0xff/0x180
[16240.322989]  __vfs_write+0x37/0x140
[16240.328164]  ? handle_mm_fault+0xce/0x240
[16240.333340]  vfs_write+0xb2/0x1b0
[16240.335013]  SyS_write+0x55/0xc0
[16240.340632]  entry_SYSCALL_64_fastpath+0x1a/0xa9

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>

In the time between rxe_send has finished and skb destructor
called, the QP's ref count might be 0, leading to a possible
QP destruction. This will lead to a kernel panic when the destructor
dereferences the QP.

The operation of incrementing QP ref count at rxe_send and decrementing
from skb destructor will prevent this crash.

BUG: unable to handle kernel NULL pointer dereference at 000000000000072c
IP: [<ffffffffa05df765>] rxe_skb_tx_dtor+0x15/0x50 [rdma_rxe]
PGD 0 [16240.211178]
Oops: 0002 [#1] SMP
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G           OE   4.9.0-mlnx #1
Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
task: ffff88042d6b1480 task.stack: ffffc90001904000
RIP: 0010:[<ffffffffa05df765>]  [<ffffffffa05df765>] rxe_skb_tx_dtor+0x15/0x50 [rdma_rxe]
RSP: 0018:ffff88043fcc3df0  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880429684700 RCX: ffff88042d248200
RDX: 00000000ffffffff RSI: 00000000fffffe01 RDI: ffff880429684700
RBP: ffff88043fcc3e00 R08: ffff88043fcda240 R09: 00000000ff2d1de6
R10: 0000000000000000 R11: 00000000f49cf6fe R12: ffff880429684700
R13: ffffffff81893f96 R14: ffffffff817d66f0 R15: ffff880427f74200
FS:  0000000000000000(0000) GS:ffff88043fcc0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000072c CR3: 000000041d3df000 CR4: 00000000000006e0
Stack:
 ffffffff817b29cf ffff880429684700 ffff88043fcc3e18 ffffffff817b42c2
 ffff880429684700 ffff88043fcc3e40 ffffffff817b4332 ffff880429684700
 ffff880427f74238 ffff880427f74228 ffff88043fcc3e58 ffffffff81893f96
Call Trace:
 <IRQ> [16240.336345]  [<ffffffff817b29cf>] ? skb_release_head_state+0x4f/0xb0
 [<ffffffff817b42c2>] skb_release_all+0x12/0x30
 [<ffffffff817b4332>] kfree_skb+0x32/0x90
 [<ffffffff81893f96>] ndisc_error_report+0x36/0x40
 [<ffffffff817d4de1>] neigh_invalidate+0x81/0xf0
 [<ffffffff817d68f7>] neigh_timer_handler+0x207/0x2b0
 [<ffffffff81109295>] call_timer_fn+0x35/0x120
 [<ffffffff81109db7>] run_timer_softirq+0x1d7/0x460
 [<ffffffff8106155e>] ? kvm_sched_clock_read+0x1e/0x30
 [<ffffffff810366b9>] ? sched_clock+0x9/0x10
 [<ffffffff810cfed2>] ? sched_clock_cpu+0x72/0xa0
 [<ffffffff818dd537>] __do_softirq+0xd7/0x289
 [<ffffffff810a6c95>] irq_exit+0xb5/0xc0
 [<ffffffff818dd372>] smp_apic_timer_interrupt+0x42/0x50
 [<ffffffff818dc682>] apic_timer_interrupt+0x82/0x90
 <EOI> [16240.395776]  [<ffffffff818da156>] ? native_safe_halt+0x6/0x10
 [<ffffffff818d9e6e>] default_idle+0x1e/0xd0
 [<ffffffff8103797f>] arch_cpu_idle+0xf/0x20
 [<ffffffff818da2c5>] default_idle_call+0x35/0x40
 [<ffffffff810e3eb5>] cpu_startup_entry+0x185/0x210
 [<ffffffff81050433>] start_secondary+0x103/0x130
RIP  [<ffffffffa05df765>] rxe_skb_tx_dtor+0x15/0x50 [rdma_rxe]

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The driver checks if the lower level driver supports get_stats, and if
so calls it to get the updated statistics, otherwise takes from the
current netdevice stats object.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Currently the RoCE GID management uses the ib_wq to do add and delete new GIDs
according to the netdev events.

The ib_wq isn't an ordered workqueue and thus two work elements can be executed
concurrently which will result in unexpected behavior and inconsistency of the
GIDs cache content.

Example:
ifconfig eth1 11.11.11.11/16 up

This command will invoke the following netdev events in the following order:
1. NETDEV_UP
2. NETDEV_DOWN
3. NETDEV_UP

If (2) and (3) will be executed concurrently or in reverse order, instead of
having a new GID with 11.11.11.11 IP, we will end up without any new GIDs.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The failure in creation of debugfs entries for mr_cache left entries,
which were already created.

It caused to mismatch and misguiding for the end users. The solution
is to clean mr_cache debugfs root, so no leftovers will be in the
system. In addition, let's document why the error is not needed to be
forwarded to user in case of failure.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

There are no users for IB_QP_CREATE_USE_GFP_NOIO flag,
so let's remove it.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.

The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.

The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Commit 21caf2fc ("mm: teach mm by current context info to not do I/O
during memory allocation") added the memalloc_noio_(save|restore) functions
to enable people to modify the MM behavior by disabling I/O during memory
allocation. This was further extended in Fixes: 934f3072 ("mm: clear
__GFP_FS when PF_MEMALLOC_NOIO is set"). memalloc_noio_* functions prevent
allocation paths recursing back into the filesystem without explicitly
changing the flags for every allocation site.

However the IPoIB hasn't been keeping up with the changes and missed
completely these memalloc_noio_* calls. This led to update of
allocation site with special QP creation flag, see commit 09b93088
("IB: Add a QP creation flag to use GFP_NOIO allocations"), while this
flag is supported by small number of drivers in IB stack.

Let's change it by updating to memalloc_noio_* calls and allow
for every driver underneath enjoy NOIO allocations.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch checks if there is a driver below that
needs to be updated on the new MTU and calls it
accordingly.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The msleep(1) may do not sleep 1 ms as expected
and will sleep longer. The simple conversion from
msleep to usleep_range between 1ms and 2ms can solve an
issue.

The full and comprehensive explanation can be found at [1] and [2].

[1] https://lkml.org/lkml/2007/8/3/250
[2] Documentation/timers/timers-howto.txt
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch makes use of IB core's ib_modify_qp_with_udata function that
also resolves the DMAC and handles udata.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch adds new function ib_modify_qp_with_udata so that
uverbs layer can avoid handling L2 mac address at verbs layer
and depend on the core layer to resolve the mac address consistently
for all required QPs.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull sparc fixes from David Miller:

 - Fix DMA regression in 4.13 merge window, only certain chips can do
   64-bit DMA. From Dave Dushar.

 - Correct cpu cross-call algorithm to correctly detect stalled or stuck
   remote cpus, from Jane Chu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Measure receiver forward progress to avoid send mondo timeout
  SPARC64: Fix sun4v DMA panic

Pull irq fix from Thomas Gleixner:
 "Fix the fallout from reworking the locking and resource management in
  request/free_irq()"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Keep chip buslock across irq_request/release_resources()

Pull SMP fix from Thomas Gleixner:
 "Replace the bogus BUG_ON in the cpu hotplug code"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/hotplug: Replace BUG_ON and react useful

Merge tag 'regmap-fix-w1-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap

Pull regmap fix from Mark Brown:
 "Fix build due to w1 header refactoring

  The regmap support for w1 was added shortly before a reorganization of
  the w1 headers. While this was noticed before the merge window and
  efforts made to get it resolved in what was sent that managed to fall
  through the cracks, this cleans up and updates things so we look for
  the header in the new location.

  It didn't cause build failures as the driver that's going to be the
  first user got held up with other review issues"

* tag 'regmap-fix-w1-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: regmap-w1: Fix build troubles

Pull SCSI fixes from James Bottomley:
 "This is actually just a small set of mainly bug fixes for the original
  merge window code plus a few trivial updates and qedi boot from SAN
  support feature patch"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: libfc: pass an error pointer to fc_disc_error()
  scsi: hisi_sas: make several const arrays static
  scsi: qla2xxx: Off by one in qlt_ctio_to_cmd()
  scsi: sg: fix SG_DXFER_FROM_DEV transfers
  scsi: virtio_scsi: always read VPD pages for multiqueue too
  scsi: qedf: fix spelling mistake: "offlading" -> "offloading"
  scsi: qedi: fix another spelling mistake: "alloction" -> "allocation"
  scsi: isci: fix typo in function names
  scsi: cxlflash: return -EFAULT if copy_from_user() fails
  scsi: qedi: Add support for Boot from SAN over iSCSI offload

Several variables had their types changed from unsigned long to u32,
but the printk()-style format to print them wasn't updated, leading to:

    arch/blackfin/kernel/flat.c: In function 'bfin_get_addr_from_rp':
    arch/blackfin/kernel/flat.c:35:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'u32' [-Wformat]
    arch/blackfin/kernel/flat.c: In function 'bfin_put_addr_at_rp':
    arch/blackfin/kernel/flat.c:80:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'u32' [-Wformat]

Fixes: 468138d7 ("binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The offset of the entry in struct rpc_version has to match the version
number.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 1c5876dd ("sunrpc: move p_count out of struct rpc_procinfo")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>