We simply can use the standard net_device stats.

We do not need to clear fields that are already 0.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4 uses a private struct net_device_stats in a vain attempt
to avoid races.

This is buggy because multiple cpus could call mlx4_en_get_stats()
at the same time, so ret_stats can not guarantee stable results.

To fix this, we need to switch to ndo_get_stats64() as this
method provides per-thread storage.

This allows to reduce mlx4_en_priv bloat.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_clear_stats() clears about everything but few TX ring
fields are missing :
- queue_stopped, wake_queue, tso_packets, xmit_more
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) mlx4_en_xmit() can increment priv->stats.tx_dropped, but this variable
is overwritten in mlx4_en_DUMP_ETH_STATS().

2) This increment was not SMP safe, as a port might have many TX queues.

Add a per TX ring tx_dropped to fix these issues.

This is u32 as mlx4_en_DUMP_ETH_STATS() will add a 32bit field.

So lets avoid bugs with SNMP agents having to cope with partial
overwraps. (One of these agents being bond_fold_stats())
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have this situation: that EP hash table, contains only the EPs
that are listening, while the transports one, has the opposite.
We have to traverse both to dump all.

But when we traverse the transports one we will also get EPs that are
in the EP hash if they are listening. In this case, the EP is dumped
twice.

We will fix it by checking if the endpoint that is in the endpoint
hash table contains any ep->asoc in there, as it means we will also
find it via transport hash, and thus we can/should skip it, depending
on the filters used, like 'ss -l'.

Still, we should NOT skip it if the user is listing only listening
endpoints, because then we are not traversing the transport hash.
so we have to check idiag_states there also.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a typo in the driver, replace comma with a semicolon at the end
of statement. While using comma is a legal C here and probably does
not even generate compiler warning, it was unlikely the intention.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memcpy() currently copies mdio_bus_data into new_bus->irq, which
makes no sense, since the mdio_bus_data structure contains more than
just irqs. The code was likely supposed to copy mdio_bus_data->irqs
into the new_bus->irq instead, so fix this.

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch follows Eric Dumazet's commit 7b701764 for Atheros
atl1c driver to fix one exactly same bug in alx driver, that the
network link will be lost in 1-5 minutes after the device is up.

My laptop Lenovo Y580 with Atheros AR8161 ethernet device hit the
same problem with kernel 4.4, and it will be cured by Jarod Wilson's
commit c406700c for alx driver which get merged in 4.5. But there
are still some alx devices can't function well even with Jarod's
patch, while this patch could make them work fine. More details on
	https://bugzilla.kernel.org/show_bug.cgi?id=70761

The debug shows the issue is very likely to be related with the RX
DMA address, specifically 0x...f80, if RX buffer get 0x...f80 several
times, their will be RX overflow error and device will stop working.

For kernel 4.5.0 with Jarod's patch which works fine with my
AR8161/Lennov Y580, if I made some change to the
	__netdev_alloc_skb
		--> __alloc_page_frag()
to make the allocated buffer can get an address with 0x...f80,
then the same error happens. If I make it to 0x...f40 or 0x....fc0,
everything will be still fine. So I tend to believe that the
0x..f80 address cause the silicon to behave abnormally.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Cc: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

The team_device_event() notifier calls team_compute_features() to fix
vlan_features under team->lock to protect team->port_list. The problem is
that subsequent __team_compute_features() calls netdev_change_features()
to propagate vlan_features to upper vlan devices while team->lock is still
taken. This can lead to deadlock when NETIF_F_LRO is modified on lower
devices or team device itself.

Example:
The team0 as active backup with eth0 and eth1 NICs. Both eth0 & eth1 are
LRO capable and LRO is enabled. Thus LRO is also enabled on team0.

The command 'ethtool -K team0 lro off' now hangs due to this deadlock:

dev_ethtool()
-> ethtool_set_features()
 -> __netdev_update_features(team)
  -> netdev_sync_lower_features()
   -> netdev_update_features(lower_1)
    -> __netdev_update_features(lower_1)
    -> netdev_features_change(lower_1)
     -> call_netdevice_notifiers(...)
      -> team_device_event(lower_1)
       -> team_compute_features(team) [TAKES team->lock]
        -> netdev_change_features(team)
         -> __netdev_update_features(team)
          -> netdev_sync_lower_features()
           -> netdev_update_features(lower_2)
            -> __netdev_update_features(lower_2)
            -> netdev_features_change(lower_2)
             -> call_netdevice_notifiers(...)
              -> team_device_event(lower_2)
               -> team_compute_features(team) [DEADLOCK]

The bug is present in team from the beginning but it appeared after the commit
fd867d51 (net/core: generic support for disabling netdev features down stack)
that adds synchronization of features with lower devices.

Fixes: fd867d51 (net/core: generic support for disabling netdev features down stack)
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Documentation: dsa: misc fixes

Here are some miscelaneous documentation fixes for DSA, I targeted "net"
because these are not functional code changes, but still documentation fixes
per-se.

Changes in v2:

- reword what the port_vlan_filtering is about based on feedback from Vivien and Ido
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Described what the port_vlan_filtering function is supposed to
accomplish.

Fixes: fb2dabad ("net: dsa: support VLAN filtering switchdev attr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We no longer have a priv_size structure member since 5feebd0a ("net:
dsa: Remove allocation of driver private memory")
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function has been removed in 4baee937 ("net: dsa: remove DSA
link polling") in favor of using the PHYLIB polling mechanism.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.

Fixes: 183233be "sfc: Allocate and link PIO buffers; map them with write-combining"
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gregory CLEMENT says:

====================
Fix spinlock usage in HWBM

these two patches fix spinlock related issues introduced in v4.6. They
have been reported by Russell King and Jean-Jacques Hiblot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When hwbm_pool_add exited in error the spinlock was not released. This
patch fixes this issue.

Fixes: 8cb2d8bf ("net: add a hardware buffer management helper API")
Reported-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The spinlock used by the hwbm functions must be initialized by the
network driver. This commit fixes this lack and the following erros when
lockdep is enabled:

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
[<c010ff80>] (unwind_backtrace) from [<c010bd08>] (show_stack+0x10/0x14)
[<c010bd08>] (show_stack) from [<c032913c>] (dump_stack+0xb4/0xe0)
[<c032913c>] (dump_stack) from [<c01670e4>] (__lock_acquire+0x1f58/0x2060)
[<c01670e4>] (__lock_acquire) from [<c0167dec>] (lock_acquire+0xa4/0xd0)
[<c0167dec>] (lock_acquire) from [<c06f6650>] (_raw_spin_lock_irqsave+0x54/0x68)
[<c06f6650>] (_raw_spin_lock_irqsave) from [<c058e830>] (hwbm_pool_add+0x1c/0xdc)
[<c058e830>] (hwbm_pool_add) from [<c043f4e8>] (mvneta_bm_pool_use+0x338/0x490)
[<c043f4e8>] (mvneta_bm_pool_use) from [<c0443198>] (mvneta_probe+0x654/0x1284)
[<c0443198>] (mvneta_probe) from [<c03b894c>] (platform_drv_probe+0x4c/0xb0)
[<c03b894c>] (platform_drv_probe) from [<c03b7158>] (driver_probe_device+0x214/0x2c0)
[<c03b7158>] (driver_probe_device) from [<c03b72c4>] (__driver_attach+0xc0/0xc4)
[<c03b72c4>] (__driver_attach) from [<c03b5440>] (bus_for_each_dev+0x68/0x9c)
[<c03b5440>] (bus_for_each_dev) from [<c03b65b8>] (bus_add_driver+0x1a0/0x218)
[<c03b65b8>] (bus_add_driver) from [<c03b79cc>] (driver_register+0x78/0xf8)
[<c03b79cc>] (driver_register) from [<c01018f4>] (do_one_initcall+0x90/0x1dc)
[<c01018f4>] (do_one_initcall) from [<c0900de4>] (kernel_init_freeable+0x15c/0x1fc)
[<c0900de4>] (kernel_init_freeable) from [<c06eed90>] (kernel_init+0x8/0x114)
[<c06eed90>] (kernel_init) from [<c0107910>] (ret_from_fork+0x14/0x24)

Fixes: baa11ebc ("net: mvneta: Use the new hwbm framework")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before calling the nla_parse_nested function, make sure the pointer to the
attribute is not null. This patch fixes several potential null pointer
dereference vulnerabilities in the tipc netlink functions.
Signed-off-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the coding error in determining the enable flag for
the application/protocol. The enable flag should be set for all protocols
but the eth.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enhances ethtool link mode bitmap to include
25G/50G/100G speed along with interface modes
Signed-off-by: Vidya Sagar Ravipati <vidya@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Policer was not dumping or updating timestamps
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I found a serious performance bug in packet schedulers using hrtimers.

sch_htb and sch_fq are definitely impacted by this problem.

We constantly rearm high resolution timers if some packets are throttled
in one (or more) class, and other packets are flying through qdisc on
another (non throttled) class.

hrtimer_start() does not have the mod_timer() trick of doing nothing if
expires value does not change :

	if (timer_pending(timer) &&
            timer->expires == expires)
                return 1;

This issue is particularly visible when multiple cpus can queue/dequeue
packets on the same qdisc, as hrtimer code has to lock a remote base.

I used following fix :

1) Change htb to use qdisc_watchdog_schedule_ns() instead of open-coding
it.

2) Cache watchdog prior expiration. hrtimer might provide this, but I
prefer to not rely on some hrtimer internal.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One timer, whose handler keeps reading on MMIO register for EEH
core to detect error in time, is started when the PCI device driver
is loaded. MMIO register can't be accessed during PE reset in EEH
recovery. Otherwise, the unexpected recursive error is triggered.
The timer isn't closed that time if the interface isn't brought
up. So the unexpected recursive error is seen during EEH recovery
when the interface is down.

This avoids the unexpected recursive EEH error by closing the timer
in qlge_io_error_detected() before EEH PE reset unconditionally. The
timer is started unconditionally after EEH PE reset in qlge_io_resume().
Also, the timer should be closed unconditionally when the device is
removed from the system permanently in qlge_io_error_detected().
Reported-by: Shriya R. Kulkarni <shriyakul@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In gre6 xmit path, we are sending a GRE packet, so set fl6 proto
to IPPROTO_GRE properly.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.

If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms
Signed-off-by: David S. Miller <davem@davemloft.net>

"priority" needs to be signed for the error handling to work.

Fixes: 39651abd ('qed: add support for dcbx.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow-up to commit e27f4a94 ("bpf: Use mount_nodev not mount_ns
to mount the bpf filesystem"), which removes the FS_USERNS_MOUNT flag.

The original idea was to have a per mountns instance instead of a
single global fs instance, but that didn't work out and we had to
switch to mount_nodev() model. The intent of that middle ground was
that we avoid users who don't play nice to create endless instances
of bpf fs which are difficult to control and discover from an admin
point of view, but at the same time it would have allowed us to be
more flexible with regard to namespaces.

Therefore, since we now did the switch to mount_nodev() as a fix
where individual instances are created, we also need to remove userns
mount flag along with it to avoid running into mentioned situation.
I don't expect any breakage at this early point in time with removing
the flag and we can revisit this later should the requirement for
this come up with future users. This and commit e27f4a94 have
been split to facilitate tracking should any of them run into the
unlikely case of causing a regression.

Fixes: b2197755 ("bpf: add support for persistent maps/progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit fa50d974 ("ipv4: Namespaceify ip_default_ttl sysctl knob")
moves the default TTL assignment, and as side-effect IPv4 TTL now
has a default value only if sysctl support is enabled (CONFIG_SYSCTL=y).

The sysctl_ip_default_ttl is fundamental for IP to work properly,
as it provides the TTL to be used as default. The defautl TTL may be
used in ip_selected_ttl, through the following flow:

  ip_select_ttl
    ip4_dst_hoplimit
      net->ipv4.sysctl_ip_default_ttl

This commit fixes the issue by assigning net->ipv4.sysctl_ip_default_ttl
in net_init_net, called during ipv4's initialization.

Without this commit, a kernel built without sysctl support will send
all IP packets with zero TTL (unless a TTL is explicitly set, e.g.
with setsockopt).

Given a similar issue might appear on the other knobs that were
namespaceify, this commit also moves them.

Fixes: fa50d974 ("ipv4: Namespaceify ip_default_ttl sysctl knob")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use memdup_user to duplicate a memory region from user-space to
kernel-space, instead of open coding using kmalloc & copy_from_user.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the statement
  assert(priv || priv->ae_handle);
the right side of || is only evaluated if priv is null.

v2:
	As suggested by David Leight and David Miller the assert
	statements are removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sk_err and sk_err_soft fields are positive errno values and
userspace applications rely on this when using getsockopt(SO_ERROR).

ATM code places an -errno into sk_err_soft in sigd_send() and returns it
from svc_addparty()/svc_dropparty().

Although I am not familiar with ATM code I came to this conclusion
because:

1. sigd_send() msg->type cases as_okay and as_error both have:

   sk->sk_err = -msg->reply;

   while the as_addparty and as_dropparty cases have:

   sk->sk_err_soft = msg->reply;

   This is the source of the inconsistency.

2. svc_addparty() returns an -errno and assumes sk_err_soft is also an
   -errno:

       if (flags & O_NONBLOCK) {
           error = -EINPROGRESS;
           goto out;
       }
       ...
       error = xchg(&sk->sk_err_soft, 0);
   out:
       release_sock(sk);
       return error;

   This shows that sk_err_soft is indeed being treated as an -errno.

This patch ensures that sk_err_soft is always a positive errno.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If !count is true, count < 4 is also true.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull motr tracing updates from Steven Rostedt:
 "Three more changes.

   - I forgot that I had another selftest to stress test the ftrace
     instance creation.  It was actually suppose to go into the 4.6
     merge window, but I never committed it.  I almost forgot about it
     again, but noticed it was missing from your tree.

   - Soumya PN sent me a clean up patch to not disable interrupts when
     taking the tasklist_lock for read, as it's unnecessary because that
     lock is never taken for write in irq context.

   - Newer gcc's can cause the jump in the function_graph code to the
     global ftrace_stub label to be a short jump instead of a long one.
     As that jump is dynamically converted to jump to the trace code to
     do function graph tracing, and that conversion expects a long jump
     it can corrupt the ftrace_stub itself (it's directly after that
     call).  One way to prevent gcc from using a short jump is to
     declare the ftrace_stub as a weak function, which we do here to
     keep gcc from optimizing too much"

* tag 'trace-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace/x86: Set ftrace_stub to weak to prevent gcc from using short jumps to it
  ftrace: Don't disable irqs when taking the tasklist_lock read_lock
  ftracetest: Add instance created, delete, read and enable event test

Pull m68knommu update from Greg Ungerer:
 "Only a single change to update my email address in the MAINTAINERS
  file"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: change m68knommu maintainer email address

Pull sparc updates from David Miller:
 "Some 32-bit kgdb cleanups from Sam Ravnborg, and a hugepage TLB flush
  overhead fix on 64-bit from Nitin Gupta"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Reduce TLB flushes during hugepte changes
  aeroflex/greth: fix warning about unused variable
  openprom: fix warning
  sparc32: drop superfluous cast in calls to __nocache_pa()
  sparc32: fix build with STRICT_MM_TYPECHECKS
  sparc32: use proper prototype for trapbase
  sparc32: drop local prototype in kgdb_32
  sparc32: drop hardcoding trap_level in kgdb_trap

I'm looking at trying to possibly merge the 32-bit and 64-bit versions
of the x86 uaccess.h implementation, but first this needs to be cleaned
up.

For example, the 32-bit version of "__copy_from_user_inatomic()" is
mostly the special cases for the constant size, and it's actually almost
never relevant.  Most users aren't actually using a constant size
anyway, and the few cases that do small constant copies are better off
just using __get_user() instead.

So get rid of the unnecessary complexity.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm looking at trying to possibly merge the 32-bit and 64-bit versions
of the x86 uaccess.h implementation, but first this needs to be cleaned
up.

For example, the 32-bit version of "__copy_to_user_inatomic()" is mostly
the special cases for the constant size, and it's actually never
relevant.  Every user except for one aren't actually using a constant
size anyway, and the one user that uses it is better off just using
__put_user() instead.

So get rid of the unnecessary complexity.

[ The same cleanup should likely happen to __copy_from_user_inatomic()
  as well, but that one has a lot more users that I need to take a look
  at first ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull f2fs updates from Jaegeuk Kim:
 "In this round, as Ted pointed out, fscrypto allows one more key prefix
  given by filesystem to resolve backward compatibility issues.  Other
  than that, we've fixed several error handling cases by introducing
  a fault injection facility.  We've also achieved performance
  improvement in some workloads as well as a bunch of bug fixes.

  Summary:

  Enhancements:
   - fs-specific prefix for fscrypto
   - fault injection facility
   - expose validity bitmaps for user to be aware of fragmentation
   - fallocate/rm/preallocation speed up
   - use percpu counters

  Bug fixes:
   - some inline_dentry/inline_data bugs
   - error handling for atomic/volatile/orphan inodes
   - recover broken superblock"

* tag 'for-f2fs-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (73 commits)
  f2fs: fix to update dirty page count correctly
  f2fs: flush pending bios right away when error occurs
  f2fs: avoid ENOSPC fault in the recovery process
  f2fs: make exit_f2fs_fs more clear
  f2fs: use percpu_counter for total_valid_inode_count
  f2fs: use percpu_counter for alloc_valid_block_count
  f2fs: use percpu_counter for # of dirty pages in inode
  f2fs: use percpu_counter for page counters
  f2fs: use bio count instead of F2FS_WRITEBACK page count
  f2fs: manipulate dirty file inodes when DATA_FLUSH is set
  f2fs: add fault injection to sysfs
  f2fs: no need inc dirty pages under inode lock
  f2fs: fix incorrect error path handling in f2fs_move_rehashed_dirents
  f2fs: fix i_current_depth during inline dentry conversion
  f2fs: correct return value type of f2fs_fill_super
  f2fs: fix deadlock when flush inline data
  f2fs: avoid f2fs_bug_on during recovery
  f2fs: show # of orphan inodes
  f2fs: support in batch fzero in dnode page
  f2fs: support in batch multi blocks preallocation
  ...

Pull btrfs updates from Chris Mason:
 "This has our merge window series of cleanups and fixes.  These target
  a wide range of issues, but do include some important fixes for
  qgroups, O_DIRECT, and fsync handling.  Jeff Mahoney moved around a
  few definitions to make them easier for userland to consume.

  Also whiteout support is included now that issues with overlayfs have
  been cleared up.

  I have one more fix pending for page faults during btrfs_copy_from_user,
  but I wanted to get this bulk out the door first"

* 'for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (90 commits)
  btrfs: fix memory leak during RAID 5/6 device replacement
  Btrfs: add semaphore to synchronize direct IO writes with fsync
  Btrfs: fix race between block group relocation and nocow writes
  Btrfs: fix race between fsync and direct IO writes for prealloc extents
  Btrfs: fix number of transaction units for renames with whiteout
  Btrfs: pin logs earlier when doing a rename exchange operation
  Btrfs: unpin logs if rename exchange operation fails
  Btrfs: fix inode leak on failure to setup whiteout inode in rename
  btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT
  Btrfs: pin log earlier when renaming
  Btrfs: unpin log if rename operation fails
  Btrfs: don't do unnecessary delalloc flushes when relocating
  Btrfs: don't wait for unrelated IO to finish before relocation
  Btrfs: fix empty symlink after creating symlink and fsync parent dir
  Btrfs: fix for incorrect directory entries after fsync log replay
  btrfs: build fixup for qgroup_account_snapshot
  btrfs: qgroup: Fix qgroup accounting when creating snapshot
  Btrfs: fix fspath error deallocation
  btrfs: make find_workspace warn if there are no workspaces
  btrfs: make find_workspace always succeed
  ...