Add support for setting txpower from upper layer and configuring per-rate
txpower limit table.
Co-developed-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use per-phy structure for maximum txpower value initializing, since each
phy may have a different chainmask, which can impact the calculation of
power gain.
Co-developed-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For UBPR and FILS frames, the BSS_CHANGED_BEACON flag will also be set,
which causes those frames to use the beacon rate in TX descriptors.
Adjust the statement to fix this issue.

Fixes: 98686cd2 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use the new fixed rate command format to let the fixed field function
work normally.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Make mt7996_mcu_set_fixed_field() non-static in order to handle
IEEE80211_RC_SMPS_CHANGED in mt7996_mac_sta_rc_work().
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Always set the fixed_bw bitfield for fixed rate frames to keep it being
sent with specific bandwidth. Without this change, the bw of fixed rate
frames will still be decided by hardware.
Reported-by: Chank Chen <chank.chen@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Refactor and update dma prefetch parts and also split band 1 traffic to
PCIe 1 to enhance throughput.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Align the format of struct bss_rate_tlv to the firmware.

Fixes: 98686cd2 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For connac3 chipsets, setting of spe_idx is moved from TX descriptor to
the fixed rate table. This patch implements the setting to support
duplicate TX mode for beacon.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This patch adds support for thermal sensor device, including the
following features:
- Support to read current chip temperature.
- Support to set/get the trigger/restore temperature for thermal service.
- Support to read current chip tx cycle.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Implement thermal protection commands and support Linux cooling device
control for mt7996 chipsets.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add EHT statistics of beamforming feedback and BW320 in debugfs tx_stats
command.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add support to correctly configure the rx chainmask of variants that
have additional auxiliary RX path. e.g., 4T5R.
The auxiliary RX path is transparent to driver, but driver needs to
correctly configure it in the set channel fw command.
Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

wifi: mt76: mt7915: fallback to non-wed mode if platform_get_resource fails in mt7915_mmio_wed_init()

mt76 assumes mt7915_mmio_wed_init can fail just after wed driver has
been attached running mtk_wed_device_attach().
Fall back to non-wed mode if platform_get_resource fails in
mt7915_mmio_wed_init routines.

Fixes: eebb7097 ("wifi: mt76: mt7915: enable wed for mt7986-wmac chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce the capability to clear WED rro session configured in the hw
according to the event reported by the MCU firmware
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce the capability to reset mt7996 chipset if requested by wed
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move WED reset code shared between mt7915 and mt7996 in common module.
This is a preliminary patch to introduce WED reset support for mt7996.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the WLAN nic and transmitted on the
LAN one
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED rx support for mt7996
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the LAN nic and transmitted on the
WLAN one
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue

This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76_mmio_wed_offload_enable and mt76_mmio_wed_offload_disable routines
will be reused by mt7996 driver for wed support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76_mmio_wed_init_rx_buf and mt76_mmio_wed_release_rx_buf routines
in common code.
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

No need cast (void *) to (struct mt7615_phy *).
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Permit to load precal from NVMEM cell for mt7915. The NVMEM cell must be
named "precal" to be correctly loaded.

NVMEM cell must already account the correct offset and be placed after
the EEPROM as the function expect the data right from the start.
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Generilize mt76_get_of_eeprom_from_nvmem to use alternative cell name by
passing the cell name as an arg and expose it.

Rename it to mt76_get_of_data_from_nvmem to better reflect the now more
generic usage.

This is to permit driver to load additional cell, like precal cell.
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since mt76_get_of_eeprom is not used by mt7915 anymore, unexport it and
make it static again.

Also drop offset arg as it's only supported for MTD and was always set
to 0, hardcode the MTD functio instead.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Limit support for precal loading for mt7915 only to MTD. Passing data
from DT doesn't support offset and NVMEM require a different cell name
and doesn't support offset hence only MTD way is actually supported.

Rename mt76_get_of_eeprom_from_mtd to mt76_get_of_data_from_mtd as it is
now used for a more generic purpose and export it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix typo in mt76_get_of_eeprom_from_nvmem where eeprom was misspelled as
epprom.

Fixes: 5bef3a40 ("wifi: mt76: add support for providing eeprom in nvmem cells")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Commit 495184ac ("mt76: mt7915: add support for applying
pre-calibration data") was fundamentally broken and never worked.

The idea (before NVMEM support) was to expand the MTD function and pass
an additional offset. For normal EEPROM load the offset would always be
0. For the purpose of precal loading, an offset was passed that was
internally the size of EEPROM, since precal data is right after the
EEPROM.

Problem is that the offset value passed is never handled and is actually
overwrite by

	offset = be32_to_cpup(list);
	ret = mtd_read(mtd, offset, len, &retlen, eep);

resulting in the passed offset value always ingnored. (and even passing
garbage data as precal as the start of the EEPROM is getting read)

Fix this by adding to the current offset value, the offset from DT to
correctly read the piece of data at the requested location.

Cc: stable@vger.kernel.org
Fixes: 495184ac ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix the uninitialized variable warning in mt7996_mac_tx_free.

Fixes: 2461599f ("wifi: mt76: mt7996: get tx_retries and tx_failed from txfree")
Signed-off-by: Yi-Chia Hsieh <yi-chia.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The mtcl table, configured by platform vendor, provides regulatory
information for 5.9/6 GHz channels. mt792x should work on
corresponding channels supported by mtcl. This patch would parse
the settings in mtcl table and apply the result into chip side.
Signed-off-by: Rong Yan <rong.yan@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add ability to explicitly forbid LED registration using DT led\status = "disabled".
Tested-by: Alexey D. Filimonov <alexey@filimonic.net>
Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Don't enable firmware debug mode to prevent SER flow stuck due to fail
to reset payload buffer, and clear HALT_C2H_INT to avoid handling
unexpected interrupt at beginning.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-6-pkshih@realtek.com

To diagnose the reason why firmware or hardware get abnormal, add to dump
MAC registers related to counters and interrupt masks. With these values,
people can classify problems and check if registers values are unexpected,
and then correct them. However, it could possible false alarm because
firmware triggers this SER event by wrong conditions that we should
correct it at firmware or register settings.

In field, SER might happen under special conditions, and very hard to
happen again, so dump lots of registers to provide rich information to
catch the problem.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-5-pkshih@realtek.com

To activate SER (system error recovery) in firmware, we have to configure
IMR to trigger interrupts, and then SER can check registers to know if it
need to reset hardware or notify driver to re-configure whole settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-4-pkshih@realtek.com