- 27 Jul, 2010 15 commits
-
-
Stephen M. Cameron authored
Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
and delete duplicated comment Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Julia Lawall authored
The end of the function is reachable both when host is and is not NULL. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r exists@ expression E,E1; identifier f; statement S1,S2,S3; @@ if ((E == NULL && ...) || ...) { ... when != if (...) S1 else S2 when != E = E1 * E->f ... when any return ...; } else S3 // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Ryan Kuester authored
I may have an explanation for the LSI 1068 HBA hangs provoked by ATA pass-through commands, in particular by smartctl. First, my version of the symptoms. On an LSI SAS1068E B3 HBA running 01.29.00.00 firmware, with SATA disks, and with smartd running, I'm seeing occasional task, bus, and host resets, some of which lead to hard faults of the HBA requiring a reboot. Abusively looping the smartctl command, # while true; do smartctl -a /dev/sdb > /dev/null; done dramatically increases the frequency of these failures to nearly one per minute. A high IO load through the HBA while looping smartctl seems to improve the chance of a full scsi host reset or a non-recoverable hang. I reduced what smartctl was doing down to a simple test case which causes the hang with a single IO when pointed at the sd interface. See the code at the bottom of this e-mail. It uses an SG_IO ioctl to issue a single pass-through ATA identify device command. If the buffer userspace gives for the read data has certain alignments, the task is issued to the HBA but the HBA fails to respond. If run against the sg interface, neither the test code nor smartctl causes a hang. sd and sg handle the SG_IO ioctl slightly differently. Unless you specifically set a flag to do direct IO, sg passes a buffer of its own, which is page-aligned, to the block layer and later copies the result into the userspace buffer regardless of its alignment. sd, on the other hand, always does direct IO unless the userspace buffer fails an alignment test at block/blk-map.c line 57, in which case a page-aligned buffer is created and used for the transfer. The alignment test currently checks for word-alignment, the default setup by scsi_lib.c; therefore, userspace buffers of almost any alignment are given directly to the HBA as DMA targets. The LSI 1068 hardware doesn't seem to like at least a couple of the alignments which cross a page boundary (see the test code below). Curiously, many page-boundary-crossing alignments do work just fine. So, either the hardware has an bug handling certain alignments or the hardware has a stricter alignment requirement than the driver is advertising. If stricter alignment is required, then in no case should misaligned buffers from userspace be allowed through without being bounced or at least causing an error to be returned. It seems the mptsas driver could use blk_queue_dma_alignment() to advertise a stricter alignment requirement. If it does, sd does the right thing and bounces misaligned buffers (see block/blk-map.c line 57). The following patch to 2.6.34-rc5 makes my symptoms go away. I'm sure this is the wrong place for this code, but it gets my idea across. Acked-by:"Desai, Kashyap" <Kashyap.Desai@lsi.com> Signed-off-by:
-
Eric Moore authored
Adding DIF Type 2 protection support, as well as turning on 32 byte cdb's, and setting the cdb length for > 16 byte in the SCSI_IO->control parameter. Signed-off-by:
Martin Petersen <martin.petersen@oracle.com> Signed-off-by:
Eric Moore <eric.moore@lsi.com> Signed-off-by:
-
Anton Blanchard authored
A driver needs to be ready to take an interrupt as soon as it registers an interrupt handler. I noticed the following oops when testing kdump: ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010) ibmvscsi 30000002: SRP_VERSION: 16.a ibmvscsi 30000002: SRP_VERSION: 16.a Unable to handle kernel paging request for data at address 0x00000000 ... pc: c000000004085e34: .tasklet_action+0xf4/0x1dc ... c000000004086fe4 .__do_softirq+0x16c/0x2c0 c00000000403138c .call_do_softirq+0x14/0x24 c00000000400ee14 .do_softirq+0xa0/0x104 c00000000408690c .irq_exit+0x70/0xd0 c00000000400f190 .do_IRQ+0x214/0x2a8 c000000004004804 hardware_interrupt_entry+0x1c/0x98 --- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54 c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0 c0000000040e7f00 .__setup_irq+0x2ec/0x3f0 c0000000040e8198 .request_threaded_irq+0x194/0x22c c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0 c00000000446c764 .ibmvscsi_probe+0x688/0x710 c00000000402903c .vio_bus_probe+0x37c/0x3e4 c000000004403f10 .driver_probe_device+0xec/0x1b8 c000000004404088 .__driver_attach+0xac/0xf4 c000000004403184 .bus_for_each_dev+0x98/0x104 c000000004403c98 .driver_attach+0x40/0x60 c0000000044026f0 .bus_add_driver+0x154/0x324 c0000000044045d0 .driver_register+0xe8/0x1ac c00000000402b2a8 .vio_register_driver+0x54/0x74 c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0 c000000004009834 .do_one_initcall+0x98/0x1d8 c0000000049005b4 .kernel_init+0x27c/0x33c c000000004031550 .kernel_thread+0x54/0x70 srp_task needs to be setup before request_irq. The patch below fixes the oops. Signed-off-by:
Anton Blanchard <anton@samba.org> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
- 21 Jul, 2010 4 commits
-
-
Christof Schmitt authored
Commit 64deb6ef changed the way status read buffers are handled but forgot to adjust the mempool to the new size. Add the call to resize the mempool after the exchange config data. Also use the define instead of the hard coded number in the fsf callback for consistency. Reviewed-by:
Swen Schillig <swen@vnet.ibm.com> Signed-off-by:
Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by:
-
Christof Schmitt authored
Trying to read the FC host statistics on an offline adapter results in a 5 seconds wait. Reading the statistics tries to issue an exchange port data request which first waits up to 5 seconds for an entry in the request queue. Change the strategy for getting a free SBAL to exit when the queue is stopped. Reading the statistics will then fail without the wait. Reviewed-by:
-
Swen Schillig authored
A false check was performed whether an unchained ct_els is possible or not. Signed-off-by:
-
Wayne Boyer authored
It was possible to overflow the buffer used to print out the formatted version of the resource path. The fix is to limit the number of bytes that get formatted. This patch also updates the ipr_show_resource_path function to display the resource address for devices that are attached to adapters that don't support resource paths. Signed-off-by:
Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by:
-
- 12 Jun, 2010 1 commit
-
-
Linus Torvalds authored
-
- 11 Jun, 2010 20 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: wimax/i2400m: fix missing endian correction read in fw loader net8139: fix a race at the end of NAPI pktgen: Fix accuracy of inter-packet delay. pkt_sched: gen_estimator: add a new lock net: deliver skbs on inactive slaves to exact matches ipv6: fix ICMP6_MIB_OUTERRORS r8169: fix mdio_read and update mdio_write according to hw specs gianfar: Revive the driver for eTSEC devices (disable timestamping) caif: fix a couple range checks phylib: Add support for the LXT973 phy. net: Print num_rx_queues imbalance warning only when there are allocated queues
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6Linus Torvalds authored
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: PM / x86: Save/restore MISC_ENABLE register
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstableLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: Btrfs: The file argument for fsync() is never null Btrfs: handle ERR_PTR from posix_acl_from_xattr() Btrfs: avoid BUG when dropping root and reference in same transaction Btrfs: prohibit a operation of changing acl's mask when noacl mount option used Btrfs: should add a permission check for setfacl Btrfs: btrfs_lookup_dir_item() can return ERR_PTR Btrfs: btrfs_read_fs_root_no_name() returns ERR_PTRs Btrfs: unwind after btrfs_start_transaction() errors Btrfs: btrfs_iget() returns ERR_PTR Btrfs: handle kzalloc() failure in open_ctree() Btrfs: handle error returns from btrfs_lookup_dir_item() Btrfs: Fix BUG_ON for fs converted from extN Btrfs: Fix null dereference in relocation.c Btrfs: fix remap_file_pages error Btrfs: uninitialized data is check_path_shared() Btrfs: fix fallocate regression Btrfs: fix loop device on top of btrfs
-
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: clear bridge resource range if BIOS assigned bad one PCI: hotplug/cpqphp, fix NULL dereference Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/" PCI: change resource collision messages from KERN_ERR to KERN_INFO
-
Yinghai Lu authored
Yannick found that video does not work with 2.6.34. The cause of this bug was that the BIOS had assigned the wrong range to the PCI bridge above the video device. Before 2.6.34 the kernel would have shrunk the size of the bridge window, but since d65245c3 PCI: don't shrink bridge resources the kernel will avoid shrinking BIOS ranges. So zero out the old range if we fail to claim it at boot time; this will cause us to allocate a new range at startup, restoring the 2.6.34 behavior. Fixes regression https://bugzilla.kernel.org/show_bug.cgi?id=16009. Reported-by:
Yannick <yannick.roehlly@free.fr> Acked-by:
Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by:
Yinghai Lu <yinghai@kernel.org> Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org>
-
Jiri Slaby authored
There are devices out there which are PCI Hot-plug controllers with compaq PCI IDs, but are not bridges, hence have pdev->subordinate NULL. But cpqphp expects the pointer to be non-NULL. Add a check to the probe function to avoid oopses like: BUG: unable to handle kernel NULL pointer dereference at 00000050 IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp] *pdpt = 0000000033779001 *pde = 0000000000000000 ... The device here was: 00:0b.0 PCI Hot-plug controller [0804]: Compaq Computer Corporation PCI Hotplug Controller [0e11:a0f7] (rev 11) Subsystem: Compaq Computer Corporation Device [0e11:a2f8] Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Greg KH <greg@kroah.com> Signed-off-by:
-
Jesse Barnes authored
This reverts commit 75568f80. Since they're just a convenience anyway, remove these symlinks since they're causing duplicate filename errors in the wild. Acked-by:
Alex Chiang <achiang@canonical.com> Signed-off-by:
-
Bjorn Helgaas authored
We can often deal with PCI resource issues by moving devices around. In that case, there's no point in alarming the user with messages like these. There are many bug reports where the message itself is the only problem, e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/413419 . Signed-off-by:
-
Dan Carpenter authored
The "file" argument for fsync is never null so we can remove this check. What drew my attention here is that 7ea80859: "drop unused dentry argument to ->fsync" introduced an unconditional dereference at the start of the function and that generated a smatch warning. Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
Chris Mason <chris.mason@oracle.com>
-
Dan Carpenter authored
posix_acl_from_xattr() returns both ERR_PTRs and null, but it's OK to pass null values to set_cached_acl() Signed-off-by:
-
Sage Weil authored
If btrfs_ioctl_snap_destroy() deletes a snapshot but finishes with end_transaction(), the cleaner kthread may come in and drop the root in the same transaction. If that's the case, the root's refs still == 1 in the tree when btrfs_del_root() deletes the item, because commit_fs_roots() hasn't updated it yet (that happens during the commit). This wasn't a problem before only because btrfs_ioctl_snap_destroy() would commit the transaction before dropping the dentry reference, so the dead root wouldn't get queued up until after the fs root item was updated in the btree. Since it is not an error to drop the root reference and the root in the same transaction, just drop the BUG_ON() in btrfs_del_root(). Signed-off-by:
Sage Weil <sage@newdream.net> Signed-off-by:
-
Shi Weihua authored
when used Posix File System Test Suite(pjd-fstest) to test btrfs, some cases about setfacl failed when noacl mount option used. I simplified used commands in pjd-fstest, and the following steps can reproduce it. ------------------------ # cd btrfs-part/ # mkdir aaa # setfacl -m m::rw aaa <- successed, but not expected by pjd-fstest. ------------------------ I checked ext3, a warning message occured, like as: setfacl: aaa/: Operation not supported Certainly, it's expected by pjd-fstest. So, i compared acl.c of btrfs and ext3. Based on that, a patch created. Fortunately, it works. Signed-off-by:
Shi Weihua <shiwh@cn.fujitsu.com> Signed-off-by:
-
Shi Weihua authored
On btrfs, do the following ------------------ # su user1 # cd btrfs-part/ # touch aaa # getfacl aaa # file: aaa # owner: user1 # group: user1 user::rw- group::rw- other::r-- # su user2 # cd btrfs-part/ # setfacl -m u::rwx aaa # getfacl aaa # file: aaa # owner: user1 # group: user1 user::rwx <- successed to setfacl group::rw- other::r-- ------------------ but we should prohibit it that user2 changing user1's acl. In fact, on ext3 and other fs, a message occurs: setfacl: aaa: Operation not permitted This patch fixed it. Signed-off-by:
-
Dan Carpenter authored
btrfs_lookup_dir_item() can return either ERR_PTRs or null. Signed-off-by:
-
Dan Carpenter authored
btrfs_read_fs_root_no_name() returns ERR_PTRs on error so I added a check for that. It's not clear to me if it can also return NULL pointers or not so I left the original NULL pointer check as is. Signed-off-by:
-
Dan Carpenter authored
This was added by a22285a6: "Btrfs: Integrate metadata reservation with start_transaction". If we goto out here then we skip all the unwinding and there are locks still held etc. Signed-off-by:
-
Dan Carpenter authored
btrfs_iget() returns an ERR_PTR() on failure and not null. Signed-off-by:
-
Dan Carpenter authored
Unwind and return -ENOMEM if the allocation fails here. Signed-off-by:
-
Dan Carpenter authored
If btrfs_lookup_dir_item() fails, we should can just let the mount fail with an error. Signed-off-by:
-
Yan, Zheng authored
Tree blocks can live in data block groups in FS converted from extN. So it's easy to trigger the BUG_ON. Signed-off-by:
Yan Zheng <zheng.yan@oracle.com> Signed-off-by:
-
