- 14 Apr, 2016 11 commits
-
-
Chris Wilson authored
Now that the reset_counter is stored on the request, we can rearrange the code to handle reading the counter versus waiting during the atomic modesetting for readibility (by deleting the hairiest of codes). Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-8-git-send-email-chris@chris-wilson.co.uk
-
Chris Wilson authored
As the request is only valid during the same global reset epoch, we can record the current reset_counter when constructing the request and reuse it when waiting upon that request in future. This removes a very hairy atomic check serialised by the struct_mutex at the time of waiting and allows us to transfer those waits to a central dispatcher for all waiters and all requests. PS: With per-engine resets, we obviously cannot assume a global reset epoch for the requests - a per-engine epoch makes the most sense. The challenge then is how to handle checking in the waiter for when to break the wait, as the fine-grained reset may also want to requeue the request (i.e. the assumption that just because the epoch changes the request is completed may be broken - or we just avoid breaking that assumption with the fine-grained resets). Signed-off-by:
-
Chris Wilson authored
In the reset_counter, we use two bits to track a GPU hang and reset. The low bit is a "reset-in-progress" flag that we set to signal when we need to break waiters in order for the recovery task to grab the mutex. As soon as the recovery task has the mutex, we can clear that flag (which we do by incrementing the reset_counter thereby incrementing the gobal reset epoch). By clearing that flag when the recovery task holds the struct_mutex, we can forgo a second flag that simply tells GEM to ignore the "reset-in-progress" flag. The second flag we store in the reset_counter is whether the reset failed and we consider the GPU terminally wedged. Whilst this flag is set, all access to the GPU (at least through GEM rather than direct mmio access) is verboten. PS: Fun is in store, as in the future we want to move from a global reset epoch to a per-engine reset engine with request recovery. Signed-off-by:
-
Chris Wilson authored
If we, when we store the reset_counter for the operation, we ensure that it is not in a wedged or in the middle of a reset, we can then assert that if any reset occurs the reset_counter must change. Later we can just compare the operation's reset epoch against the current counter to see if we need to abort the operation (to handle the hang). Signed-off-by:
-
Chris Wilson authored
This is principally a little bit of syntatic sugar to hide the atomic_read()s throughout the code to retrieve the current reset_counter. It also provides the other utility functions to check the reset state on the already read reset_counter, so that (in later patches) we can read it once and do multiple tests rather than risk the value changing between tests. v2: Be more strict on converting existing i915_reset_in_progress() over to the more verbose i915_reset_in_progress_or_wedged(). Signed-off-by:
-
Chris Wilson authored
Currently there is a #define to enable extra BUG_ON for debugging requests and associated activities. I want to expand its use to cover all of GEM internals (so that we can saturate the code with asserts). We can add a Kconfig option to make it easier to enable - with the usual caveats of not enabling unless explicitly requested. Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-3-git-send-email-chris@chris-wilson.co.uk
-
Chris Wilson authored
Separate out the layers of includes (linux, drm, intel, i915) so that it is a little easier to order our definitions between our multiple reentrant headers. A couple of headers needed fixes to make them more standalone (forgotten includes, forward declarations etc). Signed-off-by:
-
Chris Wilson authored
Our driver compiles clean (nowadays thanks to 0day) but for me, at least, it would be beneficial if the compiler threw an error rather than a warning when it found a piece of suspect code. (I use this to compile-check patch series and want to break on the first compiler error in order to fix the patch.) v2: Kick off a new "Debugging" submenu for i915.ko At this point, we applied it to the kernel and promptly kicked it out again as it broke buildbots (due to a compiler warning on 32bits): commit 908d759b Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Tue May 26 07:46:21 2015 +0200 Revert "drm/i915: Force clean compilation with -Werror" v3: Avoid enabling -Werror for allyesconfig/allmodconfig builds, using COMPILE_TEST as a suitable proxy suggested by Andrew Morton. (Damien) Only make the option available for EXPERT to reinforce that the option should not be casually enabled. Signed-off-by:
-
Mika Kuoppala authored
With gen9+ the edram capabilities are defined so that we can calculate the edram (ellc) size accordingly. Note that there are undefined combinations for some subset of edram capability bits. Return the closest size for undefined indexes. Even if we get it wrong with beginning of future gen enabling, the size information is currently only used for boot message and in debugfs entry. v2: Use function instead of hard to read macro (Daniel) v3: s/INTEL_INFO/INTEL_GEN (Matthew) Signed-off-by:
Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by:
Matthew Auld <matthew.auld@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460557604-7126-2-git-send-email-mika.kuoppala@intel.com
-
Mika Kuoppala authored
Store the edram capabilities instead of only the size of edram. This is preparatory patch to allow edram size calculation based on edram capability bits for gen9+. With gen9 the edram is behind llc and is a separate entity. With hsw/bdw it was more of a victim cache for LLC so the name 'eLLC' might be warranted. Regardless, rename all mentions of eLLC to EDRAM to clear the confusion. v2: return bytes for edram size (Chris) s/eLLC/eDRAM in output if we are gen > 8 v3: rebase, INTEL_GEN (Chris) Signed-off-by: -
Mika Kuoppala authored
For gen9 onwards, eDRAM is a true memory side cache. So there is no need to program idi hash mask as it is for eLLC only. v2: INTEL_GEN (Chris), s/has/hash (Matthew) Signed-off-by:
-
- 13 Apr, 2016 7 commits
-
-
Jani Nikula authored
The whole file is ignored on CONFIG_ACPI=n. Reviewed-by:
Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460127589-8357-1-git-send-email-jani.nikula@intel.com
-
Michał Winiarski authored
We started to use PIPE_CONTROL to write render ring seqno in order to combat seqno write vs interrupt generation problems. This was introduced by commit 7c17d377 ("drm/i915: Use ordered seqno write interrupt generation on gen8+ execlists"). On gen8+ size of PIPE_CONTROL with Post Sync Operation should be 6 dwords. When we're using older 5-dword variant it's possible to observe inconsistent values written by PIPE_CONTROL with Post Sync Operation from user batches, resulting in rendering corruptions. v2: Fix BAT failures v3: Comments on alignment and thrashing high dword of seqno (Chris) v4: Updated commit msg (Mika) Testcase: igt/gem_pipe_control_store_loop/*-qword-write Issue: VIZ-7393 Cc: stable@vger.kernel.org Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Reviewed-by:
Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Signed-off-by:
-
Mika Kuoppala authored
Experiments with heaven 4.0 benchmark and skylake gt3e (rev 0xa) suggest that WaForceContextSaveRestoreNonCoherent is needed for all revs. Extending this to all revs cures a gpu hang with rev 0xa when running heaven4.0 gpu benchmark. We have been here before, with problems enabling gt4e and extending up to revision F0 instead of false claims of bspec of E0 only. See commit <e238659d> ("drm/i915/skl: Default to noncoherent access up to F0"). In retrospect we should have covered this with this big blanket back then already, as E0 vs F0 discrepancy was suspicious enough. Previously the WaForceEnableNonCoherent has been tied to context non-coherence, atleast in relevant hsds. So keep this tie and extended this alongside. Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Cc: Ben Widawsky <benjamin.widawsky@intel.com> Cc: Timo Aaltonen <tjaalton@ubuntu.com> Cc: stable@vger.kernel.org Reported-by:
Mike Lothian <mike@fireburn.co.uk> References: https://bugs.freedesktop.org/show_bug.cgi?id=93491Signed-off-by:
Ben Widawsky <benjamin.widawsky@intel.com> Tested-by:
Timo Aaltonen <tjaalton@ubuntu.com> Link: http://patchwork.freedesktop.org/patch/msgid/1459860977-27751-2-git-send-email-mika.kuoppala@intel.com
-
Mika Kuoppala authored
For all gt3 and gt4 skylake variants, extend the usage of WaRsDisableCoarsePowerGating for all revisions. Without this gt3 and gt4 skylakes up to atleast rev 0xa can gpu hang or system hang. Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Cc: Ben Widawsky <benjamin.widawsky@intel.com> Cc: Timo Aaltonen <tjaalton@ubuntu.com> Cc: <stable@vger.kernel.org> Reported-by:
Mikael Djurfeldt <mikael@djurfeldt.com> References: https://bugs.freedesktop.org/show_bug.cgi?id=94161Signed-off-by:
-
Jani Nikula authored
Sudden realization: $ grep -ho "INTEL_INFO([^)]*)->[a-zA-Z0-9_]*" *.[ch] | sed 's/.*->//' |\ sort | uniq -c | sort -rn | head -5 446 gen 24 num_pipes 10 ring_mask 9 color 4 subslice_per_slice Acked-by: -
Tvrtko Ursulin authored
We can use the new pin/lazy unpin API for simplicity and more performance in the execlist submission paths. v2: * Fix error handling and convert more users. * Compact some names for readability. v3: * intel_lr_context_free was not unpinning. * Special case for GPU reset which otherwise unbalances the HWS object pages pin count by running the engine initialization only (not destructors). v4: * Rebased on top of hws setup/init split. Signed-off-by:Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1460472042-1998-1-git-send-email-tvrtko.ursulin@linux.intel.com [tursulin: renames: s/hwd/hws/, s/obj_addr/vaddr/] Reviewed-by:
-
Tvrtko Ursulin authored
Split the hardware status page into setup and initialisation, where setup means setting up the driver state to support the engine, and initialization means programming the hardware with the before set up state. This way the design matches the design of the engine setup/init code which is split in the same fashion and it enables the stages to be used in a balanced fashion (engine setup - hws setup, engine init - hws init). This will enable the upcoming improvements to slot in without any kludges on the GPU reset path. Signed-off-by:
-
- 12 Apr, 2016 22 commits
-
-
Ville Syrjälä authored
Check whether the DPLL is even enabled before readoing out the dividers and trying to derive port_clock on CHV. We already did this on VLV. Also remove the comment "MIPI" comment from the VLV code since we call this function whenever the pipe is enabled. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-9-git-send-email-ville.syrjala@linux.intel.comReviewed-by:
-
Ville Syrjälä authored
pgm_ratios in stored as a register value in pipe config, so let's dump this one as hex as well. Signed-off-by:
-
Ville Syrjälä authored
Use the proper refclock frequency (100MHz) when reading out the current DSI clock on CHV. Signed-off-by:
-
Ville Syrjälä authored
On VLV at least, the BIOS may leave the DSI PLL enabled in some wonky state where it just refuses to lock. Simply disabling the PLL before reconfiguring it is not enough to fix it, but power gating the PLL prior to reconfiguring does work. This happens on BYT FFRD8 when booting with HDMI connected so the DSI display will not be lit up by the BIOS. Also we can remove the code for BXT that disables the PLL before enabling it again. v2: s/vlv/intel/ since BXT made thing generic v3: Remove the BXT disable PLL before enable trick Signed-off-by:
-
Ville Syrjälä authored
All the values in the DSI PLL LFSR seed table fit into 9bits, so change the type to u16 from u32 to save a bit of space. drivers/gpu/drm/i915/i915.ko: -.rodata 90824 +.rodata 90760 Signed-off-by:
-
Ville Syrjälä authored
Enable the unclaimd register detection stuff on vlv/chv since we've now fixed the known problems during suspend. This reverts commit c81eeea6. Signed-off-by:
Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
DPINVGTT lives inside the disp2d power well so we can't frob it unless we know the power well is active. Let's this stuff into vlv_display_irq_reset() which is only called at the right times so that we don't get unclaimed register access errors. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164Signed-off-by:
-
Ville Syrjälä authored
The registers frobbed by vlv_init_display_clock_gating() libve inside the disp2d power well, so frobbing them while the power well is down results in unclaimed register access warning (and of course the values won't stick). Let's do this setup after we know the power well is enabled. It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state when the power well goes down, but fortunately the values we've been writing are actually the reset defaults. MI_ARB_VLV actually retains its value even if the power well was turned off, we just can't access it while the power well is down. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164Signed-off-by:
-
Ville Syrjälä authored
We expect vlv_display_irq_reset() to have been called prior to vlv_display_irq_postinstall() so let's WARN if that isn't the case. Signed-off-by:
-
Ville Syrjälä authored
Replace the hand rolled IMR/IER setup in vlv_display_irq_postinstall() with GEN5_IRQ_INIT(). Also rename the iir_mask to enable_mask to avoid consusion since we no longer deal with IIR here. Signed-off-by:
-
Ville Syrjälä authored
For a bit of extra paranoia make sure the display irqs are all cleared before we enabled them when turning on the power well. This should really be the case already since the power well was off which resets everything. Signed-off-by:
-
Ville Syrjälä authored
Reshuffle the code a bit to move the vlv/chv display irq functions away from the main irq hooks, next to the other sub (de,gt,etc.) hooks. v2: Rebased due to changes in vlv_display_irq_reset() Signed-off-by:
-
Ville Syrjälä authored
During runtime PM we'll be reinitializing interrupt support from the ground up. However since the display power well will be off at that time, well end up with a ton of unclaimed register accesses from the display irq setup. Since we turned off the power well already before runtime suspend, we've flagged display irqs as disabled during runtime PM transitions. So we can just check that flag to see if we should do skip display irqs during irq setup. During driver load display irqs will be flagged as enabled since we've turned on the power well already, however the power well code will have skipped the display irq setup since irq support as a whole wasn't yet enabled when the power well was enabled. So we'll want to do the display irq setup in that case. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164Signed-off-by:
-
Ville Syrjälä authored
The vlv/chv display irq setup was a bit of mess after I ran out of steam when working on it last. Fix it up so that we just have a _reset() and _postinstall() hooks for the display irqs, and use those consistently. v2: Clear out pipestat_irq_mask[] and PIPE_FIFO_UNDERRUN_STATUS in vlv_display_irq_reset() (Imre) Signed-off-by: -
Ville Syrjälä authored
No clue what this is supposed to achieve. I think it's been there since the very beginning, so presumably some kind of kludge for very early silicon. Let's just throw it out. Signed-off-by:
-
Ville Syrjälä authored
The underruns we were seeing when enabling eDP port A on ILK seem to have been caused by prematurely clearing the LP1+ watermark values when disabling LP1+ watermarks. Now that the watermarks are handled properly, we can rip out the underrun suppression around the port A enable. We still need to worry about the underruns on FDI when enabling the eDP PLL. But as Bspec tells us, we can avoid that by a vblank wait on the pipe driving FDI just prior to enabling the eDP PLL. Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
-
Ville Syrjälä authored
Once again ILK is unhappy if we clear out the LP1+ watermark levels outright, and instead we must disable the levels we don't want while still leaving the actual programmed watermark levels intact. Fixes underruns on the already enabled pipe when programming watermarks while enabling the second pipe. Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Matt Roper <matthew.d.roper@intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93787Signed-off-by:
-
Ville Syrjälä authored
Take a bigger hammer to the underrun suppression on ILK. Instead of trying to suppress them at specific points in the modeset sequence just silence them across the entire sequence. This gets rid of some underruns at least on my ILK. Note that this changes SNB and IVB to follow the same approach just to keep the code less convoluted. The difference is that on those platforms we won't suppress CPU underruns for port A since it doesn't seem to be necessary. My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is as effective on other PCH port types. Perhaps we still need some of Daniel's extra vblank waits [2]? I've still been able to trigger an underrun on the other pipe, but fixing that perhaps needs the LP1+ disable trick I implemented here [1] which never got merged. A few details which hamper stress testing on my ILK are that sometimes the PCH transcoder gets messed up and refuses to shut down, and sometimes even the panel power sequencer apparently gets stuck on the always on position. [1] https://lists.freedesktop.org/archives/intel-gfx/2014-March/041317.html [2] https://lists.freedesktop.org/archives/intel-gfx/2016-January/086397.html v2: Add a note that we also get underruns when enabling PCH ports Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Tvrtko Ursulin authored
Rather than blindly waking up all forcewake domains on command submission, we can teach each engine what is (or are) the correct one to take. On platforms with multiple forcewake domains like VLV, CHV, SKL and BXT, this has the potential of lowering the GPU and CPU power use and submission latency. To implement it we add a function named intel_uncore_forcewake_for_reg whose purpose is to query which forcewake domains need to be taken to read or write a specific register with raw mmio accessors. These enables the execlists engine setup to query which forcewake domains are relevant per engine on the currently running platform. v2: * Kerneldoc. * Split from intel_uncore.c macro extraction, WARN_ON, no warns on old platforms. (Chris Wilson) v3: * Single domain per engine, mention all registers, bi-directional function and a new name, fix handling of gen6 and gen7 writes. (Chris Wilson) Signed-off-by: -
Tvrtko Ursulin authored
Chris Wilson points out that we can remove them from the array since they are always written to with raw accessors. Signed-off-by:
-
Tvrtko Ursulin authored
Knowledge of which register per platform belonds in which forcewake domain was embedded in the MMIO accessors themselves. Extract it into standalone macros so they can be used from new code in the following patches. This causes GCC to compile some of the MMIO accessors slightly differently and grows the code a tiny amount. But none of the growth is on the fast-path so it does not matter hugely. Affected sizes before: 00000000000026f0 00000000000001a5 t gen6_read16 0000000000002390 00000000000001a5 t gen6_read32 00000000000028a0 00000000000001a5 t gen6_read64 00000000000061d0 000000000000019e t gen8_write16 0000000000006510 000000000000019d t gen8_write32 0000000000006370 000000000000019d t gen8_write64 00000000000021f0 000000000000019d t gen8_write8 Affected sizes after: 0000000000002840 00000000000001aa t gen6_read16 00000000000024e0 00000000000001a9 t gen6_read32 00000000000029f0 00000000000001a9 t gen6_read64 0000000000004f20 00000000000001b5 t gen8_write16 0000000000004ba0 00000000000001b4 t gen8_write32 00000000000050e0 00000000000001b4 t gen8_write64 0000000000004d60 00000000000001b4 t gen8_write8 Other MMIO accessors are not affected in size. Signed-off-by:
-
Tvrtko Ursulin authored
On platforms with multiple forcewake domains it seems more efficient to request all desired ones and then to wait for acks to avoid needlessly serializing on each domain. v2: Rebase. Signed-off-by:
-
