It is werid that qlge driver supports NETIF_F_TSO6 but
not NETIF_F_IPV6_CSUM. This also causes some kernel warning [1]
when VLAN device setups on a qlge interface.

I think the qlge hardware doesn't support NETIF_F_IPV6_CSUM,
so we have to just remove the NETIF_F_TSO6 flag.

After this patch, the TCP/IPv6 traffic becomes normal again,
no kernel warnings any more.

NOTE: I only tested it on 2.6.32 kernel, even if the upstream
kernel could fix this automatically (it is hard to track NETIF*
flags), removing it is also safe.

1. https://bugzilla.redhat.com/show_bug.cgi?id=891839

Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit c3ae62af (tcp: should drop incoming frames without ACK flag
set) added a regression on the handling of RST messages.

RST should be allowed to come even without ACK bit set. We validate
the RST by checking the exact sequence, as requested by RFC 793 and
5961 3.2, in tcp_validate_incoming()
Reported-by: Eric Wong <normalperson@yhbt.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Eric Wong <normalperson@yhbt.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver is used on Microblaze and will be used
on Arm Zynq.
Microblaze doesn't define NO_IRQ and no IRQ is 0.
Arm still uses NO_IRQ as -1 and there is no option
to connect IRQ to irq 0.

That's why <= 0 is only one option how to find out
undefined IRQ.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Axi ethernet can't be used on PPC because it is
little endian IP and PPC is big endian.
This system can't be designed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of the previous driver unload flow, whenever bnx2x is
loaded after the UNDI driver it closes all Rx traffic.
However, this leads to management traffic also being stopped until
the network interface associated with one of its functions gets loaded.

To remedy this, management traffic is re-opened once the 'cleaning'
after the previous driver ends.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When allocating Tx queues, if for some reason
(e.g., lack of memory) allocation fails, driver will incorrectly
calculate the pointers of the various queues.

This patch repositions all pointers in such a case to point at
sequential structures in memory, allowing the bnx2x macros to
be used correctly when accessing them.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 70ac618c ("ptp: fixup Kconfig for two PHC drivers.") removed all
dependencies for the blackfin hardware time-stamping Kconfig entry. Hardware
time-stamping is only available on BF518 though. Since the Kconfig entry is
'default y', just updateing your kernel source and running `make defconfig` will
result in the the following build errors:

	drivers/net/ethernet/adi/bfin_mac.c:694: error: implicit declaration of function ‘bfin_read_EMAC_PTP_CTL’
	drivers/net/ethernet/adi/bfin_mac.c:702: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FV3’
	drivers/net/ethernet/adi/bfin_mac.c:712: error: implicit declaration of function ‘bfin_write_EMAC_PTP_CTL’
	drivers/net/ethernet/adi/bfin_mac.c:717: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FOFF’
	...

This patch adds back the dependency on BF518, and since it does not make sense
to expose this config option when the blackfin MAC driver is not enabled also
restore the dependency on BFIN_MAC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the moment, we check owner when we enable queue in tun.
This seems redundant and will break some valid uses
where fd is passed around: I think TUNSETOWNER is there
to prevent others from attaching to a persistent device not
owned by them. Here the fd is already attached,
enabling/disabling queue is more like read/write.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I move the return down a line after the debugging printk.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multiqueue tun devices support detaching a tun_file from its tun_struct
and re-attaching at a later point in time.  This allows users to disable
a specific queue temporarily.

ioctl(TUNSETIFF) allows the user to specify the network interface to
attach by name.  This means the user can attempt to attach to interface
"B" after detaching from interface "A".

The driver is not designed to support this so check we are re-attaching
to the right tun_struct.  Failure to do so may lead to oops.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace ip6_route_lookup() with addrconf_get_prefix_route() when
looking up for a prefix route. This ensures that the connected prefix
is looked up in the main table, and avoids the selection of other
matching routes located in different tables as well as blackhole
or prohibited entries.

In addition, this fixes an Opps introduced by commit 64c6d08e (ipv6:
del unreachable route when an addr is deleted on lo), that would occur
when a blackhole or prohibited entry is selected by ip6_route_lookup().
Such entries have a NULL rt6i_table argument, which is accessed by
__ip6_del_rt() when trying to lock rt6i_table->tb6_lock.

The function addrconf_is_prefix_route() is not used anymore and is
removed.

[v2] Minor indentation cleanup and log updates.
Signed-off-by: Romain Kuntz <r.kuntz@ipflavors.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tests on the flags in addrconf_get_prefix_route() does no make
much sense: the 'noflags' parameter contains the set of flags that
must not match with the route flags, so the test must be done
against 'noflags', and not against 'flags'.
Signed-off-by: Romain Kuntz <r.kuntz@ipflavors.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under unusual circumstances, TCP collapse can split a big GRO TCP packet
while its being used in a splice(socket->pipe) operation.

skb_splice_bits() releases the socket lock before calling
splice_to_pipe().

[ 1081.353685] WARNING: at net/ipv4/tcp.c:1330 tcp_cleanup_rbuf+0x4d/0xfc()
[ 1081.371956] Hardware name: System x3690 X5 -[7148Z68]-
[ 1081.391820] cleanup rbuf bug: copied AD3BCF1 seq AD370AF rcvnxt AD3CF13

To fix this problem, we must eat skbs in tcp_recv_skb().

Remove the inline keyword from tcp_recv_skb() definition since
it has three call sites.
Reported-by: Christian Becker <c.becker@traviangames.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 02275a2e (tcp: don't abort splice() after small transfers)
added a regression.

[   83.843570] INFO: rcu_sched self-detected stall on CPU
[   83.844575] INFO: rcu_sched detected stalls on CPUs/tasks: { 6} (detected by 0, t=21002 jiffies, g=4457, c=4456, q=13132)
[   83.844582] Task dump for CPU 6:
[   83.844584] netperf         R  running task        0  8966   8952 0x0000000c
[   83.844587]  0000000000000000 0000000000000006 0000000000006c6c 0000000000000000
[   83.844589]  000000000000006c 0000000000000096 ffffffff819ce2bc ffffffffffffff10
[   83.844592]  ffffffff81088679 0000000000000010 0000000000000246 ffff880c4b9ddcd8
[   83.844594] Call Trace:
[   83.844596]  [<ffffffff81088679>] ? vprintk_emit+0x1c9/0x4c0
[   83.844601]  [<ffffffff815ad449>] ? schedule+0x29/0x70
[   83.844606]  [<ffffffff81537bd2>] ? tcp_splice_data_recv+0x42/0x50
[   83.844610]  [<ffffffff8153beaa>] ? tcp_read_sock+0xda/0x260
[   83.844613]  [<ffffffff81537b90>] ? tcp_prequeue_process+0xb0/0xb0
[   83.844615]  [<ffffffff8153c0f0>] ? tcp_splice_read+0xc0/0x250
[   83.844618]  [<ffffffff814dc0c2>] ? sock_splice_read+0x22/0x30
[   83.844622]  [<ffffffff811b820b>] ? do_splice_to+0x7b/0xa0
[   83.844627]  [<ffffffff811ba4bc>] ? sys_splice+0x59c/0x5d0
[   83.844630]  [<ffffffff8119745b>] ? putname+0x2b/0x40
[   83.844633]  [<ffffffff8118bcb4>] ? do_sys_open+0x174/0x1e0
[   83.844636]  [<ffffffff815b6202>] ? system_call_fastpath+0x16/0x1b

if recv_actor() returns 0, we should stop immediately,
because looping wont give a chance to drain the pipe.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

A regression is introduced by the following commit:

	commit 4d52cfbe
	Author: Eric Dumazet <eric.dumazet@gmail.com>
	Date:   Tue Jun 2 00:42:16 2009 -0700

	    net: ipv4/ip_sockglue.c cleanups

	    Pure cleanups

but it is not a pure cleanup...

	-               if (val != -1 && (val < 1 || val>255))
	+               if (val != -1 && (val < 0 || val > 255))

Since there is no reason provided to allow ttl=0, change it back.
Reported-by: nitin padalia <padalia.nitin@gmail.com>
Cc: nitin padalia <padalia.nitin@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull sound fixes from Takashi Iwai:
 "Nothing too exciting here, just a few regression and trivial fixes,
  and new quirks for HD-audio and USB-audio.

   - HD-audio mute LED mode enum fix
   - Fix kernel panic of Digidesign Mbox2 usb-audio quirk (which was new
     in 3.8-rc1)
   - Creative BT-D1 usb-audio quirk
   - mute LED fixup for HP Pavillion 17 laptop"

* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - add mute LED for HP Pavilion 17 (Realtek codec)
  ALSA: au88x0: fix incorrect left shift
  sound: oss/pas2: Fix possible access out of array
  ALSA: usb-audio: Fix kernel panic of Digidesign Mbox2 quirk
  ALSA: usb-audio: Add support for Creative BT-D1 via usb sound quirks
  ALSA: hda - Switch "On" and "Off" for "Mute-LED Mode" kcontrol

Pull networking fixes from David Miller:

 1) New sysctl ndisc_notify needs some documentation, from Hanns
    Frederic Sowa.

 2) Netfilter REJECT target doesn't set transport header of SKB
    correctly, from Mukund Jampala.

 3) Forcedeth driver needs to check for DMA mapping failures, from Larry
    Finger.

 4) brcmsmac driver can't use usleep_range while holding locks, use
    udelay instead.  From Niels Ole Salscheider.

 5) Fix unregister of netlink bridge multicast database handlers, from
    Vlad Yasevich and Rami Rosen.

 6) Fix checksum calculations in netfilter's ipv6 network prefix
    translation module.

 7) Fix high order page allocation failures in netfilter xt_recent, from
    Eric Dumazet.

 8) mac802154 needs to use netif_rx_ni() instead of netif_rx() because
    mac802154_process_data() can execute in process rather than
    interrupt context.  From Alexander Aring.

 9) Fix splice handling of MSG_SENDPAGE_NOTLAST, otherwise we elide one
    tcp_push() too many.  From Eric Dumazet and Willy Tarreau.

10) Fix skb->truesize tracking in XEN netfront driver, from Ian
    Campbell.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
  xen/netfront: improve truesize tracking
  ipv4: fix NULL checking in devinet_ioctl()
  tcp: fix MSG_SENDPAGE_NOTLAST logic
  net/ipv4/ipconfig: really display the BOOTP/DHCP server's address.
  ip-sysctl: fix spelling errors
  mac802154: fix NOHZ local_softirq_pending 08 warning
  ipv6: document ndisc_notify in networking/ip-sysctl.txt
  ath9k: Fix Kconfig for ATH9K_HTC
  netfilter: xt_recent: avoid high order page allocations
  netfilter: fix missing dependencies for the NOTRACK target
  netfilter: ip6t_NPT: fix IPv6 NTP checksum calculation
  bridge: add empty br_mdb_init() and br_mdb_uninit() definitions.
  vxlan: allow live mac address change
  bridge: Correctly unregister MDB rtnetlink handlers
  brcmfmac: fix parsing rsn ie for ap mode.
  brcmsmac: add copyright information for Canonical
  rtlwifi: rtl8723ae: Fix warning for unchecked pci_map_single() call
  rtlwifi: rtl8192se: Fix warning for unchecked pci_map_single() call
  rtlwifi: rtl8192de: Fix warning for unchecked pci_map_single() call
  rtlwifi: rtl8192ce: Fix warning for unchecked pci_map_single() call
  ...

Using RX_COPY_THRESHOLD is incorrect if the SKB is actually smaller
than that. We have already accounted for this in
NETFRONT_SKB_CB(skb)->pull_to so use that instead.

Fixes WARN_ON from skb_try_coalesce.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: annie li <annie.li@oracle.com>
Cc: xen-devel@lists.xen.org
Cc: netdev@vger.kernel.org
Cc: stable@kernel.org # 3.7.x only
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following batch contains Netfilter fixes for 3.8-rc2, they are:

* Fix IPv6 stateless network/port translation (NPT) checksum
  calculation, from Ulrich Weber.

* Fix for xt_recent to avoid memory allocation failures if large
  hashtables are used, from Eric Dumazet.

* Fix missing dependencies in Kconfig for the deprecated NOTRACK,
  from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ACPI and power management fixes from Rafael Wysocki:

 - Removal of some ACPICA code that the kernel will never use from Lv
   Zheng.

 - APEI fix from Adrian Huang.

 - Removal of unnecessary ACPI memory hotplug driver code from Liu
   Jinsong.

 - Minor ACPI power management fixes.

 - ACPI debug code fix from Joe Perches.

 - ACPI fix to make system bus device nodes get the right names.

 - PNP resources handling fixes from Witold Szczeponik.

 - cpuidle fix for a recent regression stalling boot on systems with
   great numbers of CPUs from Daniel Lezcano.

 - cpuidle fixes from Sivaram Nair.

 - intel_idle debug message fix from Youquan Song.

 - cpufreq build regression fix from Larry Finger.

 - cpufreq fix for an obscure initialization race related to statistics
   from Konstantin Khlebnikov.

 - cpufreq change disabling the Longhaul driver by default from Rafał
   Bilski.

 - PM core fix preventing device suspend errors from happening during
   system suspend due to obscure race conditions.

 - PM QoS local variable name cleanup.

* tag 'pm+acpi-for-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: Move disabling/enabling runtime PM to late suspend/early resume
  PM / QoS: Rename local variable in dev_pm_qos_add_ancestor_request()
  ACPI / scan: Do not use dummy HID for system bus ACPI nodes
  cpufreq / governor: Fix problem with cpufreq_ondemand or cpufreq_conservative
  cpufreq / Longhaul: Disable driver by default
  cpufreq / stats: fix race between stats allocation and first usage
  cpuidle: fix lock contention in the idle path
  intel_idle: pr_debug information need separated
  cpuidle / coupled: fix ready counter decrement
  cpuidle: Fix finding state with min power_usage
  PNP: Handle IORESOURCE_BITS in resource allocation
  PNP: Simplify setting of resources
  ACPI / power: Remove useless message from device registering routine
  ACPI / glue: Update DBG macro to include KERN_DEBUG
  ACPI / PM: Do not apply ACPI_SUCCESS() to acpi_bus_get_device() result
  ACPI / memhotplug: remove redundant logic of acpi memory hotadd
  ACPI / APEI: Fix the returned value in erst_dbg_read
  ACPICA: Remove useless mini-C library.

Pull CIFS fixes from Steve French:
 "Misc small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Don't let read only caching for mandatory byte-range locked files
  CIFS: Fix write after setting a read lock for read oplock files
  Revert "CIFS: Fix write after setting a read lock for read oplock files"
  cifs: adjust sequence number downward after signing NT_CANCEL request
  cifs: move check for NULL socket into smb_send_rqst

Recent versions of udev cause synchronous firmware loading from the
probe routine to fail because the request to user space would time
out. The original fix for b43 (commit 6b6fa586) moved the firmware
load from the probe routine to a work queue, but it still used synchronous
firmware loading. This method is OK when b43 is built as a module;
however, it fails when the driver is compiled into the kernel.

This version changes the code to load the initial firmware file
using request_firmware_nowait(). A completion event is used to
hold the work queue until that file is available. This driver
reads several firmware files - the remainder can be read synchronously.
On some test systems, the async read fails; however, a following synch
read works, thus the async failure falls through to the sync try.

Reported-and-Tested by: Felix Janda <felix.janda@posteo.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>  (V3.4+)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

  The fields must be null-terminated, or simple_strtoul will cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Do not dereference p->station_id after kfree(cmd) because p
points into the cmd data structure.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Julian Wollrath <jwollrath@web.de>
Acked-by: Larry Finger <Larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pull namei.h missing include fix from Al Viro.

The new use of ESTALE in namei.h can cause compile failures on ARM with
certain configurations due to lack of errno.h.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  namei.h: include errno.h

Commit 0d0863b0 ("sctp: Change defaults on cookie hmac selection")
added a "choice" to the sctp Kconfig file.  It introduced a bug which
led to an infinite loop when while running "make oldconfig".

The problem is that the wrong symbol was defined as the default value
for the choice.  Using the correct value gets rid of the infinite loop.

Note:  if CONFIG_SCTP_COOKIE_HMAC_SHA1=y was present in the input
config file, both that and CONFIG_SCTP_COOKIE_HMAC_MD5=y be present
in the generated config file.
Signed-off-by: Alex Elder <elder@inktank.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ext4 regression fixes from Ted Ts'o:
 "Bug fixes, including two regressions introduced in v3.8.  The most
  serious of these regressions is a buffer cache leak."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: remove duplicate call to ext4_bread() in ext4_init_new_dir()
  ext4: release buffer in failed path in dx_probe()
  ext4: fix configuration dependencies for ext4 ACLs and security labels

Pull NFS client bugfixes from Trond Myklebust:

 - Fix a permissions problem when opening NFSv4 files that only have the
   exec bit set.

 - Fix a couple of typos in pNFS (inverted logic), and the mount parsing
   (missing pointer dereference).

 - Work around a series of deadlock issues due to workqueues using
   struct work_struct pointer address comparisons in the re-entrancy
   tests.  Ensure that we don't free struct work_struct prematurely if
   our work function involves waiting for completion of other work items
   (e.g. by calling rpc_shutdown_client).

 - Revert the part of commit 168e4b39 that is causing unnecessary
   warnings to be issued in the nfsd callback code.

* tag 'nfs-for-3.8-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs: avoid dereferencing null pointer in initiate_bulk_draining
  SUNRPC: Partial revert of commit 168e4b39
  NFS: Ensure that we free the rpc_task after read and write cleanups are done
  SUNRPC: Ensure that we free the rpc_task after cleanups are done
  nfs: fix null checking in nfs_get_option_str()
  pnfs: Increase the refcount when LAYOUTGET fails the first time
  NFS: Fix access to suid/sgid executables

The mute LED is in this case connected to the Mic1 VREF.

The machine also exposes the following string in BIOS:
"HP_Mute_LED_0_A", so if more machines are coming, it probably
makes sense to try to do something more generic, like for the
IDT codec.

Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1096789Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull MIPS fixes from Ralf Baechle:
 "Various fixes across the tree.  The modpost error due to
  virt_addr_valid() not being usable from modules required a number of
  preparatory cleanups so a clean fix was possible."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: 64-bit: Fix build if !CONFIG_MODULES
  MIPS: Wire up finit_module syscall.
  MIPS: Fix modpost error in modules attepting to use virt_addr_valid().
  MIPS: page.h: Remove now unnecessary #ifndef __ASSEMBLY__ wrapper.
  MIPS: Switch remaining assembler PAGE_SIZE users to <asm/asm-offsets.h>.
  MIPS: Include PAGE_S{IZE,HIFT} in <asm/offset.h>.
  MIPS: Don't include <asm/page.h> unnecessarily.
  MIPS: Fix comment.
  Revert "MIPS: Optimise TLB handlers for MIPS32/64 R2 cores."
  MIPS: perf: Fix build failure in XLP perf support.
  MIPS: Alchemy: Make 32kHz and r4k timer coexist peacefully

Merge emailed fixes from Andrew Morton:
 "Bunch of fixes:

   - delayed IPC updates.  I held back on this because of some possible
     outstanding bug reports, but they appear to have been addressed in
     later versions

   - A bunch of MAINTAINERS updates

   - Yet Another RTC driver.  I'd held this back while a couple of
     little issues were being worked out.

  I'm expecting an intrusive-but-simple patchset from Joe Perches which
  splits up printk.c into kernel/printk/*.  That will be a pig to
  maintain for two months so if it passes testing I'd like to get it
  upstream after a week or so."

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
  printk: fix incorrect length from print_time() when seconds > 99999
  drivers/rtc/rtc-vt8500.c: fix handling of data passed in struct rtc_time
  drivers/rtc/rtc-vt8500.c: correct handling of CR_24H bitfield
  rtc: add RTC driver for TPS6586x
  MAINTAINERS: fix drivers/staging/sm7xx/
  MAINTAINERS: remove include/linux/of_pwm.h
  MAINTAINERS: remove arch/*/lib/perf_event*.c
  MAINTAINERS: remove drivers/mmc/host/imxmmc.*
  MAINTAINERS: fix Documentation/mei/
  MAINTAINERS: remove arch/x86/platform/mrst/pmu.*
  MAINTAINERS: remove firmware/isci/
  MAINTAINERS: fix drivers/ieee802154/
  MAINTAINERS: fix .../plat-mxc/include/mach/imxfb.h
  MAINTAINERS: remove drivers/video/epson1355fb.c
  MAINTAINERS: fix drivers/media/usb/dvb-usb/cxusb*
  MAINTAINERS: adjust for UAPI
  MAINTAINERS: fix drivers/media/platform/atmel-isi.c
  MAINTAINERS: fix arch/arm/mach-at91/include/mach/at_hdmac.h
  MAINTAINERS: fix drivers/rtc/rtc-vt8500.c
  MAINTAINERS: remove arch/arm/plat-s5p/
  ...

Pull microblaze update from Michal Simek:
 "This fixes noMMU kernel and I have also added defconfig updates which
  fix issue with one external dependency and enable all xilinx device
  drivers for 0-day testing system.

  Additionally wire up finit_module system call, and do highmem fixup
  and pci warnings reported by the 0-day testing system"

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Update microblaze defconfigs
  microblaze: Fix pci compilation and sparse warnings
  microblaze: Add finit_module syscall
  microblaze: Kill __kmap_atomic()
  microblaze: Change section flags for noMMU
  microblaze: Microblaze wants sys_fork for noMMU too

Pull integrity subsystem regression fix from James Morris:
 "Commit fdf90729 "ima: support new kernel module syscall" by error
  modified init_module() to return INTEGRITY_UNKNOWN (which is 4) to
  user space if the kernel was built with CONFIG_IMA_APPRAISE=y.

  As a result, user space can no longer load kernel modules using
  init_module().  This commit fixes this regression."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  ima: fallback to MODULE_SIG_ENFORCE for existing kernel module syscall

vortex_wt_setdsout performs bit-negation on the bit position (wt&0x1f)
rather than on the resulting bitmask.  This code is never actually
invoked (vortex_wt_setdsout is always called with en=1), so this does
not currently cause any problem, and this patch is simply cleanup.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The NULL pointer check `!ifa' should come before its first use.

[ Bug origin : commit fd23c3b3
  (ipv4: Add hash table of interface addresses) in linux-2.6.39 ]
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 35f9c09f (tcp: tcp_sendpages() should call tcp_push() once)
added an internal flag : MSG_SENDPAGE_NOTLAST meant to be set on all
frags but the last one for a splice() call.

The condition used to set the flag in pipe_to_sendpage() relied on
splice() user passing the exact number of bytes present in the pipe,
or a smaller one.

But some programs pass an arbitrary high value, and the test fails.

The effect of this bug is a lack of tcp_push() at the end of a
splice(pipe -> socket) call, and possibly very slow or erratic TCP
sessions.

We should both test sd->total_len and fact that another fragment
is in the pipe (pipe->nrbufs > 1)

Many thanks to Willy for providing very clear bug report, bisection
and test programs.
Reported-by: Willy Tarreau <w@1wt.eu>
Bisected-by: Willy Tarreau <w@1wt.eu>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a buffer cache leak when creating a directory, introduced
in commit a774f9c2.
Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Tao Ma <boyu.mt@taobao.com>

If checksum fails, we should also release the buffer
read from previous iteration.
Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>-
Cc: stable@vger.kernel.org
--
 fs/ext4/namei.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)