There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.

The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99

There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591

It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Carpenter says:

The patch 640f763f: "net: dsa: sja1105: Add support for Spanning
Tree Protocol" from May 5, 2019, leads to the following static
checker warning:

        drivers/net/dsa/sja1105/sja1105_main.c:1073 sja1105_stp_state_get()
        warn: signedness bug returning '(-22)'

The caller doesn't check for negative errors anyway.

Fixes: 640f763f: ("net: dsa: sja1105: Add support for Spanning Tree Protocol")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The while-loop exit condition check is not correct; the
loop should continue if the returns from the function calls are
negative or the CRC status returns are invalid.  Currently it
is ignoring the returns from the function calls.  Fix this by
removing the status return checks and only break from the loop
at the very end when we know that all the success condtions have
been met.

Kudos to Dan Carpenter for describing the correct fix and
Vladimir Oltean for noting the change to the check on the number
of retries.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8aa9ebcc ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/sja1105/sja1105_spi.c:486:21: warning: symbol 'sja1105et_regs' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_spi.c:511:21: warning: symbol 'sja1105pqrs_regs' was not declared. Should it be static?

Fixes: 8aa9ebcc ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

calling connect(AF_UNSPEC) on an already connected TCP socket is an
established way to disconnect() such socket. After commit 68741a8a
("selinux: Fix ltp test connect-syscall failure") it no longer works
and, in the above scenario connect() fails with EAFNOSUPPORT.

Fix the above falling back to the generic/old code when the address family
is not AF_INET{4,6}, but leave the SCTP code path untouched, as it has
specific constraints.

Fixes: 68741a8a ("selinux: Fix ltp test connect-syscall failure")
Reported-by: Tom Deseyn <tdeseyn@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pointer l2_hdr is being assigned to itself, this is redundant
and can be removed.

Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are several spelling mistakes in dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4806e975 ("netfilter: replace NF_NAT_NEEDED with
IS_ENABLED(CONFIG_NF_NAT)") removed CONFIG_NF_NAT_NEEDED, but a new user
popped up afterwards.

Fixes: fec9c271 ("openvswitch: load and reference the NAT helper.")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_iif should be used for the raw socket lookup. inet_iif considers
rt_iif which handles the case of local traffic.

As it stands, ping to a local address with the '-I <dev>' option fails
ever since ping was changed to use SO_BINDTODEVICE instead of
cmsg + IP_PKTINFO.

IPv6 works fine.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit 153380ec ("fib_rules: Added NLM_F_EXCL support to
fib_nl_newrule") we now able to check if a rule already exists. But this
only works with iproute2. For other tools like libnl, NetworkManager,
it still could add duplicate rules with only NLM_F_CREATE flag, like

[localhost ~ ]# ip rule
0:      from all lookup local
32766:  from all lookup main
32767:  from all lookup default
100000: from 192.168.7.5 lookup 5
100000: from 192.168.7.5 lookup 5

As it doesn't make sense to create two duplicate rules, let's just return
0 if the rule exists.

Fixes: 153380ec ("fib_rules: Added NLM_F_EXCL support to fib_nl_newrule")
Reported-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking updates from David Miller:
 "Highlights:

   1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.

   2) Add fib_sync_mem to control the amount of dirty memory we allow to
      queue up between synchronize RCU calls, from David Ahern.

   3) Make flow classifier more lockless, from Vlad Buslov.

   4) Add PHY downshift support to aquantia driver, from Heiner
      Kallweit.

   5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
      contention on SLAB spinlocks in heavy RPC workloads.

   6) Partial GSO offload support in XFRM, from Boris Pismenny.

   7) Add fast link down support to ethtool, from Heiner Kallweit.

   8) Use siphash for IP ID generator, from Eric Dumazet.

   9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
      entries, from David Ahern.

  10) Move skb->xmit_more into a per-cpu variable, from Florian
      Westphal.

  11) Improve eBPF verifier speed and increase maximum program size,
      from Alexei Starovoitov.

  12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
      spinlocks. From Neil Brown.

  13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.

  14) Improve link partner cap detection in generic PHY code, from
      Heiner Kallweit.

  15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
      Maguire.

  16) Remove SKB list implementation assumptions in SCTP, your's truly.

  17) Various cleanups, optimizations, and simplifications in r8169
      driver. From Heiner Kallweit.

  18) Add memory accounting on TX and RX path of SCTP, from Xin Long.

  19) Switch PHY drivers over to use dynamic featue detection, from
      Heiner Kallweit.

  20) Support flow steering without masking in dpaa2-eth, from Ioana
      Ciocoi.

  21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
      Pirko.

  22) Increase the strict parsing of current and future netlink
      attributes, also export such policies to userspace. From Johannes
      Berg.

  23) Allow DSA tag drivers to be modular, from Andrew Lunn.

  24) Remove legacy DSA probing support, also from Andrew Lunn.

  25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
      Haabendal.

  26) Add a generic tracepoint for TX queue timeouts to ease debugging,
      from Cong Wang.

  27) More indirect call optimizations, from Paolo Abeni"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
  cxgb4: Fix error path in cxgb4_init_module
  net: phy: improve pause mode reporting in phy_print_status
  dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
  net: macb: Change interrupt and napi enable order in open
  net: ll_temac: Improve error message on error IRQ
  net/sched: remove block pointer from common offload structure
  net: ethernet: support of_get_mac_address new ERR_PTR error
  net: usb: smsc: fix warning reported by kbuild test robot
  staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
  net: dsa: support of_get_mac_address new ERR_PTR error
  net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
  vrf: sit mtu should not be updated when vrf netdev is the link
  net: dsa: Fix error cleanup path in dsa_init_module
  l2tp: Fix possible NULL pointer dereference
  taprio: add null check on sched_nest to avoid potential null pointer dereference
  net: mvpp2: cls: fix less than zero check on a u32 variable
  net_sched: sch_fq: handle non connected flows
  net_sched: sch_fq: do not assume EDT packets are ordered
  net: hns3: use devm_kcalloc when allocating desc_cb
  net: hns3: some cleanup for struct hns3_enet_ring
  ...

Pull Devicetree updates from Rob Herring:

 - Fix possible memory leak in reserved-memory failure case

 - Support for DMA parent bus which are not a parent node

 - Clang -Wunsequenced fix

 - Remove some unnecessary prints on memory alloc failures

 - Various printk msg and comment fixes

 - Update DT schema tools repository location

 - Convert simple-framebuffer binding to DT schema

 - Bindings for isl68137 and ir38064 trivial devices

 - New documentation on binding do's and don't's for binding writers to
   ignore

* tag 'devicetree-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (22 commits)
  of: unittest: Remove error printing on OOM
  of: irq: Remove WARN_ON() for kzalloc() failure
  dt-bindings: pinctrl: fix bias-pull,up typo
  dt-bindings: Update schema project location to devicetree.org github group
  of: fix clang -Wunsequenced for be32_to_cpu()
  of/device.c: fix the wrong comments
  dt-bindings: Add isl68137 as a trivial device
  dt-bindings: Add ir38064 as a trivial device
  of: del redundant type conversion
  dt-bindings: mfd: axp20x: Add fallback for axp805
  of: Improve of_phandle_iterator_next() error message
  dt-bindings: connector: Spelling mistake
  dt-bindings: Add schemas for simple-framebuffer
  of: address: Add support for the parent DMA bus
  of: address: Retrieve a parent through a callback in __of_translate_address
  dt-bindings: bus: Add binding for the Allwinner MBUS controller
  dt-bindings: interconnect: Add a dma interconnect name
  of: use correct function prototype for of_overlay_fdt_apply()
  of: reserved_mem: fix reserve memory leak
  of: property: Document that of_graph_get_endpoint_by_regs needs of_node_put
  ...

Pull randomness updates from Ted Ts'o:

 - initialize the random driver earler

 - fix CRNG initialization when we trust the CPU's RNG on NUMA systems

 - other miscellaneous cleanups and fixes.

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: add a spinlock_t to struct batched_entropy
  random: document get_random_int() family
  random: fix CRNG initialization when random.trust_cpu=1
  random: move rand_initialize() earlier
  random: only read from /dev/random after its pool has received 128 bits
  drivers/char/random.c: make primary_crng static
  drivers/char/random.c: remove unused stuct poolinfo::poolbits
  drivers/char/random.c: constify poolinfo_table

Pull fscrypt updates from Ted Ts'o:
 "Clean up fscrypt's dcache revalidation support, and other
  miscellaneous cleanups"

* tag 'fscrypt_for_linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
  fscrypt: cache decrypted symlink target in ->i_link
  vfs: use READ_ONCE() to access ->i_link
  fscrypt: fix race where ->lookup() marks plaintext dentry as ciphertext
  fscrypt: only set dentry_operations on ciphertext dentries
  fs, fscrypt: clear DCACHE_ENCRYPTED_NAME when unaliasing directory
  fscrypt: fix race allowing rename() and link() of ciphertext dentries
  fscrypt: clean up and improve dentry revalidation
  fscrypt: use READ_ONCE() to access ->i_crypt_info
  fscrypt: remove WARN_ON_ONCE() when decryption fails
  fscrypt: drop inode argument from fscrypt_get_ctx()

Pull ext4 updates from Ted Ts'o:
 "Add as a feature case-insensitive directories (the casefold feature)
  using Unicode 12.1.

  Also, the usual largish number of cleanups and bug fixes"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (25 commits)
  ext4: export /sys/fs/ext4/feature/casefold if Unicode support is present
  ext4: fix ext4_show_options for file systems w/o journal
  unicode: refactor the rule for regenerating utf8data.h
  docs: ext4.rst: document case-insensitive directories
  ext4: Support case-insensitive file name lookups
  ext4: include charset encoding information in the superblock
  MAINTAINERS: add Unicode subsystem entry
  unicode: update unicode database unicode version 12.1.0
  unicode: introduce test module for normalized utf8 implementation
  unicode: implement higher level API for string handling
  unicode: reduce the size of utf8data[]
  unicode: introduce code for UTF-8 normalization
  unicode: introduce UTF-8 character database
  ext4: actually request zeroing of inode table after grow
  ext4: cond_resched in work-heavy group loops
  ext4: fix use-after-free race with debug_want_extra_isize
  ext4: avoid drop reference to iloc.bh twice
  ext4: ignore e_value_offs for xattrs with value-in-ea-inode
  ext4: protect journal inode's blocks using block_validity
  ext4: use BUG() instead of BUG_ON(1)
  ...

Pull AFS updates from David Howells:
 "A set of fix and development patches for AFS for 5.2.

  Summary:

   - Fix the AFS file locking so that sqlite can run on an AFS mount and
     also so that firefox and gnome can use a homedir that's mounted
     through AFS.

     This required emulation of fine-grained locking when the server
     will only support whole-file locks and no upgrade/downgrade. Four
     modes are provided, settable by mount parameter:

       "flock=local"   - No reference to the server

       "flock=openafs" - Fine-grained locks are local-only, whole-file
                         locks require sufficient server locks

       "flock=strict"  - All locks require sufficient server locks

       "flock=write"   - Always get an exclusive server lock

     If the volume is a read-only or backup volume, then flock=local for
     that volume.

   - Log extra information for a couple of cases where the client mucks
     up somehow: AFS vnode with undefined type and dir check failure -
     in both cases we seem to end up with unfilled data, but the issues
     happen infrequently and are difficult to reproduce at will.

   - Implement silly rename for unlink() and rename().

   - Set i_blocks so that du can get some information about usage.

   - Fix xattr handlers to return the right amount of data and to not
     overflow buffers.

   - Implement getting/setting raw AFS and YFS ACLs as xattrs"

* tag 'afs-next-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Implement YFS ACL setting
  afs: Get YFS ACLs and information through xattrs
  afs: implement acl setting
  afs: Get an AFS3 ACL as an xattr
  afs: Fix getting the afs.fid xattr
  afs: Fix the afs.cell and afs.volume xattr handlers
  afs: Calculate i_blocks based on file size
  afs: Log more information for "kAFS: AFS vnode with undefined type\n"
  afs: Provide mount-time configurable byte-range file locking emulation
  afs: Add more tracepoints
  afs: Implement sillyrename for unlink and rename
  afs: Add directory reload tracepoint
  afs: Handle lock rpc ops failing on a file that got deleted
  afs: Improve dir check failure reports
  afs: Add file locking tracepoints
  afs: Further fix file locking
  afs: Fix AFS file locking to allow fine grained locks
  afs: Calculate lock extend timer from set/extend reply reception
  afs: Split wait from afs_make_call()

Pull misc vfs updates from Al Viro:
 "Assorted stuff, with no common topic whatsoever..."

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  libfs: document simple_get_link()
  Documentation/filesystems/Locking: fix ->get_link() prototype
  Documentation/filesystems/vfs.txt: document how ->i_link works
  Documentation/filesystems/vfs.txt: remove bogus "Last updated" date
  fs: use timespec64 in relatime_need_update
  fs/block_dev.c: remove unused include

Pull vfs 'struct file' related updates from Al Viro:
 "A bit more of 'this fget() would be better off as fdget()'
  whack-a-mole + a couple of ->f_count-related cleanups"

* 'work.file' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  media: switch to fdget()
  drm_syncobj: switch to fdget()
  amdgpu: switch to fdget()
  don't open-code file_count()
  fs: drop unused fput_atomic definition

Pull mount ABI updates from Al Viro:
 "The syscalls themselves, finally.

  That's not all there is to that stuff, but switching individual
  filesystems to new methods is fortunately independent from everything
  else, so e.g. NFS series can go through NFS tree, etc.

  As those conversions get done, we'll be finally able to get rid of a
  bunch of duplication in fs/super.c introduced in the beginning of the
  entire thing. I expect that to be finished in the next window..."

* 'work.mount-syscalls' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: Add a sample program for the new mount API
  vfs: syscall: Add fspick() to select a superblock for reconfiguration
  vfs: syscall: Add fsmount() to create a mount for a superblock
  vfs: syscall: Add fsconfig() for configuring and managing a context
  vfs: Implement logging through fs_context
  vfs: syscall: Add fsopen() to prepare for superblock creation
  Make anon_inodes unconditional
  teach move_mount(2) to work with OPEN_TREE_CLONE
  vfs: syscall: Add move_mount(2) to move mounts around
  vfs: syscall: Add open_tree(2) to reference or clone a mount

Pull misc dcache updates from Al Viro:
 "Most of this pile is putting name length into struct name_snapshot and
  making use of it.

  The beginning of this series ("ovl_lookup_real_one(): don't bother
  with strlen()") ought to have been split in two (separate switch of
  name_snapshot to struct qstr from overlayfs reaping the trivial
  benefits of that), but I wanted to avoid a rebase - by the time I'd
  spotted that it was (a) in -next and (b) close to 5.1-final ;-/"

* 'work.dcache' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  audit_compare_dname_path(): switch to const struct qstr *
  audit_update_watch(): switch to const struct qstr *
  inotify_handle_event(): don't bother with strlen()
  fsnotify: switch send_to_group() and ->handle_event to const struct qstr *
  fsnotify(): switch to passing const struct qstr * for file_name
  switch fsnotify_move() to passing const struct qstr * for old_name
  ovl_lookup_real_one(): don't bother with strlen()
  sysv: bury the broken "quietly truncate the long filenames" logics
  nsfs: unobfuscate
  unexport d_alloc_pseudo()

Pull parisc updates from Helge Deller:
 "Many great new features, fixes and optimizations, including:

   - Convert page table updates to use per-pagetable spinlocks which
     overall improves performance on SMP machines a lot, by Mikulas
     Patocka

   - Kernel debugger (KGDB) support, by Sven Schnelle

   - KPROBES support, by Sven Schnelle

   - Lots of TLB lock/flush improvements, by Dave Anglin

   - Drop DISCONTIGMEM and switch to SPARSEMEM

   - Added JUMP_LABEL, branch runtime-patching support

   - Lots of other small speedups and cleanups, e.g. for QEMU, stack
     randomization, avoidance of name clashes, documentation updates,
     etc ..."

* 'parisc-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (28 commits)
  parisc: Add static branch and JUMP_LABEL feature
  parisc: Use PA_ASM_LEVEL in boot code
  parisc: Rename LEVEL to PA_ASM_LEVEL to avoid name clash with DRBD code
  parisc: Update huge TLB page support to use per-pagetable spinlock
  parisc: Use per-pagetable spinlock
  parisc: Allow live-patching of __meminit functions
  parisc: Add memory barrier to asm pdc and sync instructions
  parisc: Add memory clobber to TLB purges
  parisc: Use ldcw instruction for SMP spinlock release barrier
  parisc: Remove lock code to serialize TLB operations in pacache.S
  parisc: Switch from DISCONTIGMEM to SPARSEMEM
  parisc: enable wide mode early
  parisc: update feature lists
  parisc: Show n/a if product number not available
  parisc: remove unused flags parameter in __patch_text()
  doc: update kprobes supported architecture list
  parisc: Implement kretprobes
  parisc: remove kprobes.h from generic-y
  parisc: Implement kprobes
  parisc: add functions required by KPROBE_EVENTS
  ...

Pull audit updates from Paul Moore:
 "We've got a reasonably broad set of audit patches for the v5.2 merge
  window, the highlights are below:

   - The biggest change, and the source of all the arch/* changes, is
     the patchset from Dmitry to help enable some of the work he is
     doing around PTRACE_GET_SYSCALL_INFO.

     To be honest, including this in the audit tree is a bit of a
     stretch, but it does help move audit a little further along towards
     proper syscall auditing for all arches, and everyone else seemed to
     agree that audit was a "good" spot for this to land (or maybe they
     just didn't want to merge it? dunno.).

   - We can now audit time/NTP adjustments.

   - We continue the work to connect associated audit records into a
     single event"

* tag 'audit-pr-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: (21 commits)
  audit: fix a memory leak bug
  ntp: Audit NTP parameters adjustment
  timekeeping: Audit clock adjustments
  audit: purge unnecessary list_empty calls
  audit: link integrity evm_write_xattrs record to syscall event
  syscall_get_arch: add "struct task_struct *" argument
  unicore32: define syscall_get_arch()
  Move EM_UNICORE to uapi/linux/elf-em.h
  nios2: define syscall_get_arch()
  nds32: define syscall_get_arch()
  Move EM_NDS32 to uapi/linux/elf-em.h
  m68k: define syscall_get_arch()
  hexagon: define syscall_get_arch()
  Move EM_HEXAGON to uapi/linux/elf-em.h
  h8300: define syscall_get_arch()
  c6x: define syscall_get_arch()
  arc: define syscall_get_arch()
  Move EM_ARCOMPACT and EM_ARCV2 to uapi/linux/elf-em.h
  audit: Make audit_log_cap and audit_copy_inode static
  audit: connect LOGIN record to its syscall record
  ...

Pull selinux updates from Paul Moore:
 "We've got a few SELinux patches for the v5.2 merge window, the
  highlights are below:

   - Add LSM hooks, and the SELinux implementation, for proper labeling
     of kernfs. While we are only including the SELinux implementation
     here, the rest of the LSM folks have given the hooks a thumbs-up.

   - Update the SELinux mdp (Make Dummy Policy) script to actually work
     on a modern system.

   - Disallow userspace to change the LSM credentials via
     /proc/self/attr when the task's credentials are already overridden.

     The change was made in procfs because all the LSM folks agreed this
     was the Right Thing To Do and duplicating it across each LSM was
     going to be annoying"

* tag 'selinux-pr-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  proc: prevent changes to overridden credentials
  selinux: Check address length before reading address family
  kernfs: fix xattr name handling in LSM helpers
  MAINTAINERS: update SELinux file patterns
  selinux: avoid uninitialized variable warning
  selinux: remove useless assignments
  LSM: lsm_hooks.h - fix missing colon in docstring
  selinux: Make selinux_kernfs_init_security static
  kernfs: initialize security of newly created nodes
  selinux: implement the kernfs_init_security hook
  LSM: add new hook for kernfs node initialization
  kernfs: use simple_xattrs for security attributes
  selinux: try security xattr after genfs for kernfs filesystems
  kernfs: do not alloc iattrs in kernfs_xattr_get
  kernfs: clean up struct kernfs_iattrs
  scripts/selinux: fix build
  selinux: use kernel linux/socket.h for genheaders and mdp
  scripts/selinux: modernize mdp

Pull swiotlb updates from Konrad Rzeszutek Wilk:
 "Cleanups in the swiotlb code and extra debugfs knobs to help with the
  field diagnostics"

* 'stable/for-linus-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb-xen: ensure we have a single callsite for xen_dma_map_page
  swiotlb-xen: simplify the DMA sync method implementations
  swiotlb-xen: use ->map_page to implement ->map_sg
  swiotlb-xen: make instances match their method names
  swiotlb: save io_tlb_used to local variable before leaving critical section
  swiotlb: dump used and total slots when swiotlb buffer is full

Pull libata updates from Jens Axboe:
 "Just two minor fixes queued up for 5.2, adding support for two
  different platforms to ahci"

* tag 'for-5.2/libata-20190507' of git://git.kernel.dk/linux-block:
  ahci: qoriq: add ls1028a platforms support
  ahci: qoriq: add lx2160 platforms support

Pull io_uring updates from Jens Axboe:
 "Set of changes/improvements for io_uring. This contains:

   - Fix of a shadowed variable (Colin)

   - Add support for draining commands (me)

   - Add support for sync_file_range() (me)

   - Add eventfd support (me)

   - cpu_online() fix (Shenghui)

   - Removal of a redundant ->error assignment (Stefan)"

* tag 'for-5.2/io_uring-20190507' of git://git.kernel.dk/linux-block:
  io_uring: use cpu_online() to check p->sq_thread_cpu instead of cpu_possible()
  io_uring: fix shadowed variable ret return code being not checked
  req->error only used for iopoll
  io_uring: add support for eventfd notifications
  io_uring: add support for IORING_OP_SYNC_FILE_RANGE
  fs: add sync_file_range() helper
  io_uring: add support for marking commands as draining

Pull block updates from Jens Axboe:
 "Nothing major in this series, just fixes and improvements all over the
  map. This contains:

   - Series of fixes for sed-opal (David, Jonas)

   - Fixes and performance tweaks for BFQ (via Paolo)

   - Set of fixes for bcache (via Coly)

   - Set of fixes for md (via Song)

   - Enabling multi-page for passthrough requests (Ming)

   - Queue release fix series (Ming)

   - Device notification improvements (Martin)

   - Propagate underlying device rotational status in loop (Holger)

   - Removal of mtip32xx trim support, which has been disabled for years
     (Christoph)

   - Improvement and cleanup of nvme command handling (Christoph)

   - Add block SPDX tags (Christoph)

   - Cleanup/hardening of bio/bvec iteration (Christoph)

   - A few NVMe pull requests (Christoph)

   - Removal of CONFIG_LBDAF (Christoph)

   - Various little fixes here and there"

* tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block: (164 commits)
  block: fix mismerge in bvec_advance
  block: don't drain in-progress dispatch in blk_cleanup_queue()
  blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release
  blk-mq: always free hctx after request queue is freed
  blk-mq: split blk_mq_alloc_and_init_hctx into two parts
  blk-mq: free hw queue's resource in hctx's release handler
  blk-mq: move cancel of requeue_work into blk_mq_release
  blk-mq: grab .q_usage_counter when queuing request from plug code path
  block: fix function name in comment
  nvmet: protect discovery change log event list iteration
  nvme: mark nvme_core_init and nvme_core_exit static
  nvme: move command size checks to the core
  nvme-fabrics: check more command sizes
  nvme-pci: check more command sizes
  nvme-pci: remove an unneeded variable initialization
  nvme-pci: unquiesce admin queue on shutdown
  nvme-pci: shutdown on timeout during deletion
  nvme-pci: fix psdt field for single segment sgls
  nvme-multipath: don't print ANA group state by default
  nvme-multipath: split bios with the ns_head bio_set before submitting
  ...

Merge tag 'leds-for-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:
 "LED core fixes and improvements:

      - avoid races with workqueue
      - Kconfig: pedantic cleanup
      - small fixes for Flash class description

  leds-lt3593:

      - remove unneeded assignment in lt3593_led_probe
      - drop pdata handling code

  leds-blinkm:

      - clean up double assignment to data->i2c_addr

  leds-pca955x, leds-pca963x:

      - revert ACPI support, as it turned out that there is no evidence
          of officially registered ACPI IDs for these devices.
      - make use of device property API

  leds-as3645a:

      - switch to fwnode property API

  LED related addition to ACPI documentation:

      - document how to refer to LEDs from remote nodes

  LED related fix to ALSA line6/toneport driver:

      - avoid polluting led_* namespace

  And lm3532 driver relocation from MFD to LED subsystem, accompanied by
  various improvements and optimizations; it entails also a change in
  omap4-droid4-xt894.dts:

      - leds: lm3532: Introduce the lm3532 LED driver
      - mfd: ti-lmu: Remove LM3532 backlight driver references
      - ARM: dts: omap4-droid4: Update backlight dt properties
      - dt: lm3532: Add lm3532 dt doc and update ti_lmu doc"

* tag 'leds-for-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: avoid races with workqueue
  ALSA: line6: Avoid polluting led_* namespace
  leds: lm3532: Introduce the lm3532 LED driver
  mfd: ti-lmu: Remove LM3532 backlight driver references
  ARM: dts: omap4-droid4: Update backlight dt properties
  dt: lm3532: Add lm3532 dt doc and update ti_lmu doc
  leds: Small fixes for Flash class description
  leds: blinkm: clean up double assignment to data->i2c_addr
  leds: pca963x: Make use of device property API
  leds: pca955x: Make use of device property API
  leds: lt3593: Remove unneeded assignment in lt3593_led_probe
  leds: lt3593: drop pdata handling code
  leds: pca955x: Revert "Add ACPI support"
  leds: pca963x: Revert "Add ACPI support"
  drivers: leds: Kconfig: pedantic cleanups
  ACPI: Document how to refer to LEDs from remote nodes
  leds: as3645a: Switch to fwnode property API

Minor conflict with the DSA legacy code removal.
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc update part 2 from Greg KH:
 "Here is the "real" big set of char/misc driver patches for 5.2-rc1

  Loads of different driver subsystem stuff in here, all over the places:
   - thunderbolt driver updates
   - habanalabs driver updates
   - nvmem driver updates
   - extcon driver updates
   - intel_th driver updates
   - mei driver updates
   - coresight driver updates
   - soundwire driver cleanups and updates
   - fastrpc driver updates
   - other minor driver updates
   - chardev minor fixups

  Feels like this tree is getting to be a dumping ground of "small
  driver subsystems" these days. Which is fine with me, if it makes
  things easier for those subsystem maintainers.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
  intel_th: msu: Add current window tracking
  intel_th: msu: Add a sysfs attribute to trigger window switch
  intel_th: msu: Correct the block wrap detection
  intel_th: Add switch triggering support
  intel_th: gth: Factor out trace start/stop
  intel_th: msu: Factor out pipeline draining
  intel_th: msu: Switch over to scatterlist
  intel_th: msu: Replace open-coded list_{first,last,next}_entry variants
  intel_th: Only report useful IRQs to subdevices
  intel_th: msu: Start handling IRQs
  intel_th: pci: Use MSI interrupt signalling
  intel_th: Communicate IRQ via resource
  intel_th: Add "rtit" source device
  intel_th: Skip subdevices if their MMIO is missing
  intel_th: Rework resource passing between glue layers and core
  intel_th: SPDX-ify the documentation
  intel_th: msu: Fix single mode with IOMMU
  coresight: funnel: Support static funnel
  dt-bindings: arm: coresight: Unify funnel DT binding
  coresight: replicator: Add new device id for static replicator
  ...

Merge tag 'char-misc-5.2-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc update part 1 from Greg KH:
 "This contains only a small number of bugfixes that would have gone to
  you for 5.1-rc8 if that had happened, but instead I let them sit in
  linux-next for an extra week just "to be sure".

  The "big" patch here is for hyper-v, fixing a bug in their sysfs files
  that could cause big problems. The others are all small fixes,
  resolving reported issues that showed up in 5.1-rcs, plus some odd
  'static' cleanups for the phy drivers that really should have waited
  for -rc1. Most of these are tagged for the stable trees, so 5.1 will
  pick them up.

  All of these have been in linux-next for a while, with no reported
  issues"

* tag 'char-misc-5.2-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  misc: rtsx: Fixed rts5260 power saving parameter and sd glitch
  binder: take read mode of mmap_sem in binder_alloc_free_page()
  intel_th: pci: Add Comet Lake support
  stm class: Fix channel bitmap on 32-bit systems
  stm class: Fix channel free in stm output free path
  phy: sun4i-usb: Make sure to disable PHY0 passby for peripheral mode
  phy: fix platform_no_drv_owner.cocci warnings
  phy: mapphone-mdm6600: add gpiolib dependency
  phy: ti: usb2: fix OMAP_CONTROL_PHY dependency
  phy: allwinner: allow compile testing
  phy: qcom-ufs: Make ufs_qcom_phy_disable_iface_clk static
  phy: rockchip-typec: Make usb3_pll_cfg and dp_pll_cfg static
  phy: phy-twl4030-usb: Fix cable state handling
  Drivers: hv: vmbus: Remove the undesired put_cpu_ptr() in hv_synic_cleanup()
  Drivers: hv: vmbus: Fix race condition with new ring_buffer_info mutex
  Drivers: hv: vmbus: Set ring_info field to 0 and remove memset
  Drivers: hv: vmbus: Refactor chan->state if statement
  Drivers: hv: vmbus: Expose monitor data only when monitor pages are used

Pull staging / IIO driver updates from Greg KH:
 "Here is the big staging and iio driver update for 5.2-rc1.

  Lots of tiny fixes all over the staging and IIO driver trees here,
  along with some new IIO drivers.

  The "counter" subsystem was added in here as well, as it is needed by
  the IIO drivers and subsystem.

  Also we ended up deleting two drivers, making this pull request remove
  a few hundred thousand lines of code, always a nice thing to see. Both
  of the drivers removed have been replaced with "real" drivers in their
  various subsystem directories, and they will be coming to you from
  those locations during this merge window.

  There are some core vt/selection changes in here, that was due to some
  cleanups needed for the speakup fixes. Those have all been acked by
  the various subsystem maintainers (i.e. me), so those are ok.

  We also added a few new drivers, for some odd hardware, giving new
  developers plenty to work on with basic coding style cleanups to come
  in the near future.

  Other than that, nothing unusual here.

  All of these have been in linux-next for a while with no reported
  issues, other than an odd gcc warning for one of the new drivers that
  should be fixed up soon"

[ I fixed up the warning myself  - Linus ]

* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
  staging: kpc2000: kpc_spi: Fix build error for {read,write}q
  Staging: rtl8192e: Remove extra space before break statement
  Staging: rtl8192u: ieee80211: Fix if-else indentation warning
  Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
  staging: most: cdev: fix chrdev_region leak in mod_exit
  staging: wlan-ng: Fix improper SPDX comment style
  staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
  staging: vc04_services: bcm2835-camera: Compress two lines into one line
  staging: rtl8723bs: core: Use !x in place of NULL comparison.
  staging: rtl8723bs: core: Prefer using the BIT Macro.
  staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
  staging: kpc2000: fix up build problems with readq()
  staging: rtlwifi: move remaining phydm .h files
  staging: rtlwifi: strip down phydm .h files
  staging: rtlwifi: delete the staging driver
  staging: fieldbus: anybus-s: rename bus id field to avoid confusion
  staging: fieldbus: anybus-s: keep device bus id in bus endianness
  Staging: sm750fb: Change *array into *const array
  staging: rtl8192u: ieee80211: Fix spelling mistake
  staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
  ...

Pull driver core/kobject updates from Greg KH:
 "Here is the "big" set of driver core patches for 5.2-rc1

  There are a number of ACPI patches in here as well, as Rafael said
  they should go through this tree due to the driver core changes they
  required. They have all been acked by the ACPI developers.

  There are also a number of small subsystem-specific changes in here,
  due to some changes to the kobject core code. Those too have all been
  acked by the various subsystem maintainers.

  As for content, it's pretty boring outside of the ACPI changes:
   - spdx cleanups
   - kobject documentation updates
   - default attribute groups for kobjects
   - other minor kobject/driver core fixes

  All have been in linux-next for a while with no reported issues"

* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
  kobject: clean up the kobject add documentation a bit more
  kobject: Fix kernel-doc comment first line
  kobject: Remove docstring reference to kset
  firmware_loader: Fix a typo ("syfs" -> "sysfs")
  kobject: fix dereference before null check on kobj
  Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
  init/config: Do not select BUILD_BIN2C for IKCONFIG
  Provide in-kernel headers to make extending kernel easier
  kobject: Improve doc clarity kobject_init_and_add()
  kobject: Improve docs for kobject_add/del
  driver core: platform: Fix the usage of platform device name(pdev->name)
  livepatch: Replace klp_ktype_patch's default_attrs with groups
  cpufreq: schedutil: Replace default_attrs field with groups
  padata: Replace padata_attr_type default_attrs field with groups
  irqdesc: Replace irq_kobj_type's default_attrs field with groups
  net-sysfs: Replace ktype default_attrs field with groups
  block: Replace all ktype default_attrs with groups
  samples/kobject: Replace foo_ktype's default_attrs field with groups
  kobject: Add support for default attribute groups to kobj_type
  driver core: Postpone DMA tear-down until after devres release for probe failure
  ...

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Fix a few memoryleaks
   - Minor improvements to the card initialization sequence
   - Partially support sleepy GPIO controllers for pwrseq eMMC

  MMC host:
   - alcor: Work with multiple-entry sglists
   - alcor: Enable DMA for writes
   - meson-gx: Improve tuning support
   - meson-gx: Avoid clock glitch when switching to DDR modes
   - meson-gx: Disable unreliable HS400 mode
   - mmci: Minor updates for support of HW busy detection
   - mmci: Support data transfers for the stm32_sdmmc variant
   - mmci: Restructure code to better support different variants
   - mtk-sd: Add support for version found on MT7620 family SOCs
   - mtk-sd: Add support for the MT8516 version
   - mtk-sd: Add Chaotian Jing as the maintainer
   - sdhci: Reorganize request-code to convert from tasklet to workqueue
   - sdhci_am654: Stabilize support for lower speed modes
   - sdhci-esdhc-imx: Add HS400 support for iMX7ULP
   - sdhci-esdhc-imx: Add support for iMX7ULP version
   - sdhci-of-arasan: Allow to disable DCMDs via DT for CQE
   - sdhci-of-esdhc: Add support for the ls1028a version
   - sdhci-of-esdhc: Several fixups for errata
   - sdhci-pci: Fix BYT OCP setting
   - sdhci-pci: Add support for Intel CML
   - sdhci-tegra: Add support for system suspend/resume
   - sdhci-tegra: Add CQE support for Tegra186 WAR
   - sdhci-tegra: Add support for Tegra194
   - sdhci-tegra: Update HW tuning process

  MEMSTICK:
   - I volunteered to help as a maintainer for the memstick subsystem,
     which is reflected by an update to the MAINTAINERS file. Changes
     are funneled through my MMC git and we will use the linux-mmc
     mailing list.

  MEMSTICK host:
   - A few minor cleanups"

* tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (87 commits)
  mmc: sdhci-pci: Fix BYT OCP setting
  dt-bindings: mmc: add DT bindings for ls1028a eSDHC host controller
  mmc: alcor: Drop pointer to mmc_host from alcor_sdmmc_host
  mmc: mtk-sd: select REGULATOR
  mmc: mtk-sd: enable internal card-detect logic.
  mmc: mtk-sd: add support for config found in mt7620 family SOCs.
  mmc: mtk-sd: don't hard-code interrupt trigger type
  mmc: core: Fix tag set memory leak
  dt-bindings: mmc: Add support for MT8516 to mtk-sd
  mmc: mmci: Prevent polling for busy detection in IRQ context
  mmc: mmci: Cleanup mmci_cmd_irq() for busy detect
  mmc: usdhi6rol0: mark expected switch fall-throughs
  mmc: core: Verify SD bus width
  mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP
  mmc: sdhci-esdhc-imx: add pm_qos to interact with cpuidle
  dt-bindings: mmc: fsl-imx-esdhc: add imx7ulp compatible string
  mmc: meson-gx: add signal resampling tuning
  mmc: meson-gx: remove Rx phase tuning
  mmc: meson-gx: avoid clock glitch when switching to DDR modes
  mmc: meson-gx: disable HS400
  ...

Merge tag 'Wimplicit-fallthrough-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull Wimplicit-fallthrough updates from Gustavo A. R. Silva:
 "Mark switch cases where we are expecting to fall through.

  This is part of the ongoing efforts to enable -Wimplicit-fallthrough.

  Most of them have been baking in linux-next for a whole development
  cycle. And with Stephen Rothwell's help, we've had linux-next
  nag-emails going out for newly introduced code that triggers
  -Wimplicit-fallthrough to avoid gaining more of these cases while we
  work to remove the ones that are already present.

  We are getting close to completing this work. Currently, there are
  only 32 of 2311 of these cases left to be addressed in linux-next. I'm
  auditing every case; I take a look into the code and analyze it in
  order to determine if I'm dealing with an actual bug or a false
  positive, as explained here:

      https://lore.kernel.org/lkml/c2fad584-1705-a5f2-d63c-824e9b96cf50@embeddedor.com/

  While working on this, I've found and fixed the several missing
  break/return bugs, some of them introduced more than 5 years ago.

  Once this work is finished, we'll be able to universally enable
  "-Wimplicit-fallthrough" to avoid any of these kinds of bugs from
  entering the kernel again"

* tag 'Wimplicit-fallthrough-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (27 commits)
  memstick: mark expected switch fall-throughs
  drm/nouveau/nvkm: mark expected switch fall-throughs
  NFC: st21nfca: Fix fall-through warnings
  NFC: pn533: mark expected switch fall-throughs
  block: Mark expected switch fall-throughs
  ASN.1: mark expected switch fall-through
  lib/cmdline.c: mark expected switch fall-throughs
  lib: zstd: Mark expected switch fall-throughs
  scsi: sym53c8xx_2: sym_nvram: Mark expected switch fall-through
  scsi: sym53c8xx_2: sym_hipd: mark expected switch fall-throughs
  scsi: ppa: mark expected switch fall-through
  scsi: osst: mark expected switch fall-throughs
  scsi: lpfc: lpfc_scsi: Mark expected switch fall-throughs
  scsi: lpfc: lpfc_nvme: Mark expected switch fall-through
  scsi: lpfc: lpfc_nportdisc: Mark expected switch fall-through
  scsi: lpfc: lpfc_hbadisc: Mark expected switch fall-throughs
  scsi: lpfc: lpfc_els: Mark expected switch fall-throughs
  scsi: lpfc: lpfc_ct: Mark expected switch fall-throughs
  scsi: imm: mark expected switch fall-throughs
  scsi: csiostor: csio_wr: mark expected switch fall-through
  ...

Pull compiler-based variable initialization updates from Kees Cook:
 "This is effectively part of my gcc-plugins tree, but as this adds some
  Clang support, it felt weird to still call it "gcc-plugins". :)

  This consolidates Kconfig for the existing stack variable
  initialization (via structleak and stackleak gcc plugins) and adds
  Alexander Potapenko's support for Clang's new similar functionality.

  Summary:

   - Consolidate memory initialization Kconfigs (Kees)

   - Implement support for Clang's stack variable auto-init (Alexander)"

* tag 'meminit-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  security: Implement Clang's stack initialization
  security: Move stackleak config to Kconfig.hardening
  security: Create "kernel hardening" config area

BUG: unable to handle kernel paging request at ffffffffa016a270
PGD 3270067 P4D 3270067 PUD 3271063 PMD 230bbd067 PTE 0
Oops: 0000 [#1
CPU: 0 PID: 6134 Comm: modprobe Not tainted 5.1.0+ #33
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:atomic_notifier_chain_register+0x24/0x60
Code: 1f 80 00 00 00 00 55 48 89 e5 41 54 49 89 f4 53 48 89 fb e8 ae b4 38 01 48 8b 53 38 48 8d 4b 38 48 85 d2 74 20 45 8b 44 24 10 <44> 3b 42 10 7e 08 eb 13 44 39 42 10 7c 0d 48 8d 4a 08 48 8b 52 08
RSP: 0018:ffffc90000e2bc60 EFLAGS: 00010086
RAX: 0000000000000292 RBX: ffffffff83467240 RCX: ffffffff83467278
RDX: ffffffffa016a260 RSI: ffffffff83752140 RDI: ffffffff83467240
RBP: ffffc90000e2bc70 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 00000000014fa61f R12: ffffffffa01c8260
R13: ffff888231091e00 R14: 0000000000000000 R15: ffffc90000e2be78
FS:  00007fbd8d7cd540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa016a270 CR3: 000000022c7e3000 CR4: 00000000000006f0
Call Trace:
 register_inet6addr_notifier+0x13/0x20
 cxgb4_init_module+0x6c/0x1000 [cxgb4
 ? 0xffffffffa01d7000
 do_one_initcall+0x6c/0x3cc
 ? do_init_module+0x22/0x1f1
 ? rcu_read_lock_sched_held+0x97/0xb0
 ? kmem_cache_alloc_trace+0x325/0x3b0
 do_init_module+0x5b/0x1f1
 load_module+0x1db1/0x2690
 ? m_show+0x1d0/0x1d0
 __do_sys_finit_module+0xc5/0xd0
 __x64_sys_finit_module+0x15/0x20
 do_syscall_64+0x6b/0x1d0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

If pci_register_driver fails, register inet6addr_notifier is
pointless. This patch fix the error path in cxgb4_init_module.

Fixes: b5a02f50 ("cxgb4 : Update ipv6 address handling api")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far we report symmetric pause only, and we don't consider the local
pause capabilities. Let's properly consider local and remote
capabilities, and report also asymmetric pause.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy_mode "2000base-x" is actually supposed to be "1000base-x", even
though the commit title of the original patch says otherwise.

Fixes: 55601a88 ("net: phy: Add 2000base-x, 2500base-x and rxaui modes")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull pidfd updates from Christian Brauner:
 "This patchset makes it possible to retrieve pidfds at process creation
  time by introducing the new flag CLONE_PIDFD to the clone() system
  call. Linus originally suggested to implement this as a new flag to
  clone() instead of making it a separate system call.

  After a thorough review from Oleg CLONE_PIDFD returns pidfds in the
  parent_tidptr argument. This means we can give back the associated pid
  and the pidfd at the same time. Access to process metadata information
  thus becomes rather trivial.

  As has been agreed, CLONE_PIDFD creates file descriptors based on
  anonymous inodes similar to the new mount api. They are made
  unconditional by this patchset as they are now needed by core kernel
  code (vfs, pidfd) even more than they already were before (timerfd,
  signalfd, io_uring, epoll etc.). The core patchset is rather small.
  The bulky looking changelist is caused by David's very simple changes
  to Kconfig to make anon inodes unconditional.

  A pidfd comes with additional information in fdinfo if the kernel
  supports procfs. The fdinfo file contains the pid of the process in
  the callers pid namespace in the same format as the procfs status
  file, i.e. "Pid:\t%d".

  To remove worries about missing metadata access this patchset comes
  with a sample/test program that illustrates how a combination of
  CLONE_PIDFD and pidfd_send_signal() can be used to gain race-free
  access to process metadata through /proc/<pid>.

  Further work based on this patchset has been done by Joel. His work
  makes pidfds pollable. It finished too late for this merge window. I
  would prefer to have it sitting in linux-next for a while and send it
  for inclusion during the 5.3 merge window"

* tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  samples: show race-free pidfd metadata access
  signal: support CLONE_PIDFD with pidfd_send_signal
  clone: add CLONE_PIDFD
  Make anon_inodes unconditional