- 22 Feb, 2021 8 commits
-
-
Jani Nikula authored
Unconditionally add fixed mode to probed modes even if EDID is present and has modes. Prepare for cases where the fixed mode is not present in EDID (such as eDP MSO). Cc: Nischal Varide <nischal.varide@intel.com> Reviewed-by:
Uma Shankar <uma.shankar@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/6979f123f3e4ed948333f1b181202bbced3c3e85.1613054234.git.jani.nikula@intel.com
-
Jani Nikula authored
Be more strict about filtering modes for eDP. Cc: Nischal Varide <nischal.varide@intel.com> Reviewed-by:
-
Jani Nikula authored
Add DPCD register definitions for eDP 1.4 Multi-SST Operation. Cc: Nischal Varide <nischal.varide@intel.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
-
José Roberto de Souza authored
This will set the right value of source_support when the port encoder/port supports PSR but sink don't. This change will also be needed in future for panel replay as psr struct needs to be initialized even if disconnected or current sink don't support PSR. Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Reviewed-by:
Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-4-jose.souza@intel.com
-
José Roberto de Souza authored
If source_support is set the platform supports PSR so no need to check it again at every CAN_PSR(). Also removing the intel_dp_is_edp() calls, if sink_support is set the sink connected is for sure a eDP panel. Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
-
José Roberto de Souza authored
There is no support for two pipes one transcoder for PSR and if we had that the current code should not use cpu_transcoder. Also I can't see a scenario where crtc_state->enable_psr2_sel_fetch is set and PSR is not enabled and if by a bug it happens PSR HW will just ignore any value in set in PSR2_MAN_TRK_CTL. So dropping all the rest and keeping the same behavior that we have with intel_psr2_program_plane_sel_fetch(). Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
-
José Roberto de Souza authored
for_each_intel_encoder.*_"can_psr" sounds strange, in my opinion "with_psr" is better. Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
-
José Roberto de Souza authored
Right now CI is blacklisting module reload, so we need to be able to enable PSR2 selective fetch in run time to test this feature before enable it by default. Changes in IGT will also be needed. v2: - Fixed handling of I915_PSR_DEBUG_ENABLE_SEL_FETCH in intel_psr_debug_set() Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
-
- 20 Feb, 2021 1 commit
-
-
Lee Shawn C authored
According to Bspec #20124, max link rate table for DP was updated at BDB version 230. Max link rate can support upto UHBR. After migrate to BDB v230, the definition for LBR, HBR2 and HBR3 were changed. For backward compatibility. If BDB version was from 216 to 229. Driver have to follow original rule to configure DP max link rate value from VBT. v2: split the mapping table to two for old and new BDB definition. v3: return link rate instead of assigning it. v4: remove the useless variable. Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Cooper Chiou <cooper.chiou@intel.com> Cc: William Tseng <william.tseng@intel.com> Signed-off-by:
Lee Shawn C <shawn.c.lee@intel.com> [vsyrjala: Try to retain the comment that VBT version 216 added some of this] Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210218052333.16109-1-shawn.c.lee@intel.com
-
- 18 Feb, 2021 2 commits
-
-
Ville Syrjälä authored
When we sanitize planes let's wait for the scanout to stop before we let the subsequent code tear down the ggtt mappings and whatnot. Cures an underrun on my ivb when I boot with VT-d enabled and the BIOS fb gets thrown out due to stolen being considered unusable with VT-d active. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk>
-
Ville Syrjälä authored
We tend to use output_format!=RGB as a shorthand for YCbCr, but this fails if we have a disabled crtc where output_format==INVALID. We're now getting some fail from intel_color_check() when we have: hw.enable==false hw.ctm!=NULL output_format==INVALID Let's avoid that by throwing INTEL_OUTPUT_FORMAT_INVALID to the dumpster, and thus everything defaults to RGB when the crtc is disabled. This does beg the deeper question of how much of the state should we in fact be validating when hw/uapi.enable==false. And should we even be doing the uapi->hw copy when uapi.enable==false? So far I've not been able to come up with satisfactory answers for myself, so I'm putting it off for the moment. Cc: Lee Shawn C <shawn.c.lee@intel.com> Fixes: 0aa5c383 ("drm/i915: support two CSC module on gen11 and later") Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2964Signed-off-by:
-
- 17 Feb, 2021 2 commits
-
-
José Roberto de Souza authored
There is nothing else to be executed after this if block. Signed-off-by:
-
Nathan Chancellor authored
-Wunintialized was disabled in commit c5627461 ("drm/i915: Disable -Wuninitialized") because there were two warnings that were false positives. The first was due to DECLARE_WAIT_QUEUE_HEAD_ONSTACK, which was fixed in LLVM 9.0.0. The second was in busywait_stop, which was fixed in LLVM 10.0.0 (issue 415). The kernel's minimum version for LLVM is 10.0.1 so this warning can be safely enabled, where it has already caught a couple bugs. Link: https://github.com/ClangBuiltLinux/linux/issues/220 Link: https://github.com/ClangBuiltLinux/linux/issues/415 Link: https://github.com/ClangBuiltLinux/linux/issues/499 Link: https://github.com/llvm/llvm-project/commit/2e040398f8d691cc378c1abb098824ff49f3f28f Link: https://github.com/llvm/llvm-project/commit/c667cdc850c2aa821ffeedbc08c24bc985c59edd Fixes: c5627461 ("drm/i915: Disable -Wuninitialized") References: 2ea4a7ba ("drm/i915/gt: Avoid uninitialized use of rpcurupei in frequency_show") References: 2034c212 ("drm/i915/display: Ensure that ret is always initialized in icl_combo_phy_verify_state") Reported-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Nathan Chancellor <nathan@kernel.org> Reviewed-by:
-
- 16 Feb, 2021 15 commits
-
-
Ville Syrjälä authored
Convert the remaining 'dev_priv's to 'i915's in the DDI clock routing functions. Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com>
-
Ville Syrjälä authored
Move icl_sanitize_encoder_pll_mapping() out from the middle of the .{enable,disable}_clock() functions. Reviewed-by: -
Ville Syrjälä authored
Instead of every new platform having yet another masive copy of the whole PLL sanitation code, let's just reuse the .disable_clock() hook for this purpose. We do need to plug this into the ICL+ DSI code for that, but fortunately it already has a suitable function we can use. We do lose the debug message though on account of not bothering to check if the clock is actually enabled or not before turning it off. We could introduce yet another vfunc to query the current state, but not sure it's worth the hassle? Reviewed-by:
-
Ville Syrjälä authored
Since .{enable,disable}_clock() are already vfuncs it's a bit silly to have if-ladders inside them. Just provide specialized version for adl-s and rkl so we don't need any of that. v2: s/dev_priv/i915/ (Lucas) Fix typos in platform names (Lucas) Reviewed-by: -
Ville Syrjälä authored
All the DPCLKA_CFGCR handling follows a common pattern. Let's extract that to a small helper that just takes a few parameters each caller can customize. Reviewed-by:
-
Ville Syrjälä authored
The other DDI .enable_clock() functions are trying to protect us against pll==NULL. A bit tempted to throw out all the WARNs as just unnecessary noise, but I guess they might have some use when poking around the shared_dpll code (not sure it wouldn't oops elsewhere though). So let's unify it all and sprinkle in the missing WARNs for icl/dg1. Reviewed-by:
-
Ville Syrjälä authored
The current code attempts to protect the RMWs into global clock routing registers with a mutex, but forgets to do so in a few places. Let's remedy that. Note that at the moment we serialize all modesets onto single wq, so this shouldn't actually matter. But maybe one day we wish to attempt parallel modesets again... Reviewed-by:
-
Ville Syrjälä authored
The DDI clock routing programming is riddled with shared registers, forcing us to do a lot of RMW. Switch over to intel_de_rmw() to make that a bit less obnoxious. Reviewed-by:
-
Ville Syrjälä authored
For ICL+ we have several styles of clock routing for DDIs: 1) TC DDI + TC PHY -> needs DDI_CLK_SEL==MG/TBT part form intel_ddi_clk_{select,disable}() and ICL_DPCLKA_CFGCR0_TC_CLK_OFF part form icl_{map,unmap}_plls_to_ports() 2) ICL/TGL combo DDI + combo PHY -> just need the stuff from icl_{map,unmap}_plls_to_ports() 3) JSL/EHL TC DDI + combo PHY -> needs DDI_CLK_SEL==MG part from intel_ddi_clk_{select,disable}() and the full combo style clock selection from icl_{map,unmap}_plls_to_ports() 4) ADLS/RKL -> these use both TC and combo DDIs with combo PHYs, however they always use the full combo style clock selection as per icl_{map,unmap}_plls_to_ports() and do not use DDI_CLK_SEL at all, thus get treated the same as 2) We extract all that from the current mess in the following way: 1) icl_ddi_tc_{enable,disable}_clock() 2) icl_ddi_combo_{enable,disable}_clock() 3) jsl_ddi_tc_{enable,disable}_clock() 4) for now we reuse icl_ddi_combo_{enable,disable}_clock() here v2: s/dev_priv/i915/ (Lucas) Reviewed-by: -
Ville Syrjälä authored
Replace dg1_{map,unmap}_plls_to_ports() with the appropriate encoder vfuncs. And let's relocate the disable function next to the enable function while at it. Reviewed-by: -
Ville Syrjälä authored
Extract the DDI clock routing for CNL into the new vfuncs. v2: s/dev_priv/i915/ (Lucas) Reviewed-by:
-
Ville Syrjälä authored
Extract the DDI clock routing clode for skl/derivatives into the new encoder vfuncs. v2: s/dev_priv/i915/ (Lucas) Reviewed-by:
-
Ville Syrjälä authored
Yank out the HSW/BDW code from intel_ddi_clk_{select,disable}() and put it into the new encoder .{enable,disable}_clock() vfuncs. v2: s/dev_priv/i915/ (Lucas) v3: Deal with FDI Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2 Signed-off-by: -
Ville Syrjälä authored
The current code dealing with the clock routing for DDI encoders is a maintenance nightmare. Let's start cleaning it up by allowing the encoder to provide vfuncs for enablign/disabling the clock. We leave them initially unimplemented, falling back to the old if-else approach. v2: Convert the FDI enable sequence Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2 Signed-off-by:
-
Ville Syrjälä authored
We want to put all DDI clock routing code into one place. Unify the FDI enable sequence to use the standard function instead of hand rolling its own. The disable sequence already uses the normal thing. Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
-
- 13 Feb, 2021 6 commits
-
-
Lucas De Marchi authored
intel_init_audio_hooks() sets up hooks in the display struct and only makes sense when we have display. Move it inside intel_init_display_hooks() so it isn't called when we don't have display. Signed-off-by:
-
Lucas De Marchi authored
Now that all display-related functions are grouped in i915_driver_register(), move them to display/ so we reduce the amount of display calls from the rest of the driver. Signed-off-by:
-
Lucas De Marchi authored
intel_gt_driver_register() may be called earlier than intel_opregion_register() and acpi_video_register(), so move it up. intel_display_debugfs_register() may be called later, together with the other display-related initializations. There is a slight change in behavior that sysfs files will show up before the display-related debugfs files, but that shouldn't be a problem - userspace shouldn't be relying in debugfs. This allows us to group all the display-related calls under a single check for "HAS_DISPLAY()" that can be later moved to a better place. Signed-off-by:
-
Lucas De Marchi authored
If drm_dev_register() fails there is no reason to continue registering the driver and initializing. Signed-off-by:
-
Matt Roper authored
In rare circumstances bugs in PCI programming, broken BIOS, or failing hardware can cause the CPU to lose access to the MMIO BAR on dgfx platforms. This is a pretty catastrophic failure since all register reads come back with values of 0xFFFFFFFF. Let's check for this special case while doing our usual checks for unclaimed registers; the FPGA_DBG register we use for those checks on modern platforms has some unused bits that will always read back as 0 when things are behaving properly; we can use them as canaries to detect when MMIO itself has suddenly broken and try to print a more informative error message in the logs. v2: Let the detection function still return 'true' if we've lost our MMIO access. We'll still get an extra false positive message about an unclaimed register access, but we'll still honor the 'mmio_debug' limit and not spam the log. (Lucas) Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210212211925.3418280-2-matthew.d.roper@intel.comReviewed-by:
-
Matt Roper authored
Although the bspec's description doesn't make it very clear, the hardware architects have confirmed that the FPGA_DBG register that we use to check for unclaimed MMIO accesses is display-specific and will only properly flag unclaimed MMIO transactions for registers in the display range. If a platform doesn't have display, FPGA_DBG itself will not be available and should not be checked. Let's move the feature flag into intel_device_info.display to more accurately reflect this. Given that we now know FPGA_DBG is display-specific, it could be argued that we should only check it on out intel_de_*() functions. However let's not make that change right now; keeping the checks in all of the existing locations still helps us catch cases where regular intel_uncore_*() functions use bad MMIO offset math / base addresses and accidentally wind up landing within an unused area within the display MMIO range. It will also help catch cases where userspace-initiated MMIO (e.g., IGT's intel_reg tool) attempt to read bad offsets within the display range. v2: Add missing hunk with the update to the HAS_FPGA_DBG_UNCLAIMED macro. (CI) Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
-
- 12 Feb, 2021 5 commits
-
-
Lyude Paul authored
Apparently the new gen9_bc platforms that Intel has introduced don't provide us with a STRAP config register to read from for initializing DDI B, C, and D detection. So, workaround this by hard-coding our strap config in intel_setup_outputs(). Changes since v4: * Split this into it's own commit Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> [originally from Tejas's work] Signed-off-by:
Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com> Signed-off-by:
Lyude Paul <lyude@redhat.com> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-5-lyude@redhat.com
-
Lyude Paul authored
Next, let's start introducing the HPD pin mappings for Intel's new gen9_bc platform in order to make hotplugging display connectors work. Since gen9_bc is just a TGP PCH along with a CML CPU, except with the same HPD mappings as ICL, we simply add a skl_hpd_pin function that is shared between gen9 and gen9_bc which handles both the traditional gen9 HPD pin mappings and the Icelake HPD pin mappings that gen9_bc uses. Changes since v4: * Split this into its own commit * Introduce skl_hpd_pin() like vsyrjala suggested and use that instead of sticking our HPD pin mappings in TGP code Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> [originally from Tejas's work] Signed-off-by:
-
Umesh Nerlige Ramappa authored
After fixing the OA_TAIL_PTR corruption, there are no more reports with reason field of zero. Drop the check for report reason. Signed-off-by:
Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> Signed-off-by:
-
Anshuman Gupta authored
DP-MST connector encoder initializes at modeset Adding a connector->encoder NULL check in order to avoid any NULL pointer dereference. intel_hdcp_enable() already handle this but debugfs can also invoke the intel_{hdcp,hdcp2_capable}. Handling it gracefully. v2: - Use necessary lock and NULL check in i915_hdcp_sink_capability_show. [Imre] Reviewed-by:Imre Deak <imre.deak@intel.com> Signed-off-by:
Anshuman Gupta <anshuman.gupta@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210211140502.22786-1-anshuman.gupta@intel.com
-
Lucas De Marchi authored
We are not checking for specific SKUs and feedback from HW team is that it may not work since it was supposed to be fixed by the same time straps stopped to be used. So, just update comment. v2: Instead of removing the check, just update the comment since feedback from HW team was that it actually may not work Signed-off-by:
-
- 11 Feb, 2021 1 commit
-
-
Lyude Paul authored
With the introduction of gen9_bc, where Intel combines Cometlake CPUs with a Tigerpoint PCH, we'll need to introduce new DDC pin mappings for this platform in order to make all of the display connectors work. So, let's do that. Changes since v4: * Split this into it's own patch - vsyrjala Changes since v5: * Rename gen9bc_port_to_ddc_pin() to gen9bc_tgp_port_to_ddc_pin() Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> [originally from Tejas's work] Signed-off-by:
-
