- 25 Apr, 2017 1 commit
-
-
Boris Brezillon authored
This is a complete rewrite of the driver whose main purpose is to support the new DT representation where the NAND controller node is now really visible in the DT and appears under the EBI bus. With this new representation, we can add other devices under the EBI bus without risking pinmuxing conflicts (the NAND controller is under the EBI bus logic and as such, share some of its pins with other devices connected on this bus). Even though the goal of this rework was not necessarily to add new features, the new driver has been designed with this in mind. With a clearer separation between the different blocks and different IP revisions, adding new functionalities should be easier (we already have plans to support SMC timing configuration so that we no longer have to rely on the configuration done by the bootloader/bootstrap). Also note that we no longer have a custom ->cmdfunc() implementation, which means we can now benefit from new features added in the core implementation for free (support for new NAND operations for example). The last thing that we gain with this rework is support for multi-chips and multi-dies chips, thanks to the clean NAND controller <-> NAND devices representation. During this transition we also dropped support for AVR32 SoCs which should soon disappear from mainline (removal of the AVR32 arch is planned for 4.12). This new driver has been tested on several platforms (at91sam9261, at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not introduce regressions, and it's worth mentioning that old bindings are still supported (which partly explain the positive diffstat). Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com>
-
- 29 Mar, 2017 2 commits
-
-
Simon Baatz authored
The clock gate used by orion_nand is not available on all platforms. When getting this optional clock gate, the code masked all errors. Let's be more precise here and actually only allow ENOENT. EPROBE_DEFER is handled like any other error code since probe deferral is not supported by drivers using module_platform_driver_probe(). Signed-off-by:
Simon Baatz <gmbnomis@gmail.com> Signed-off-by:
-
Simon Baatz authored
The clk handling in orion_nand.c had two problems: - In the probe function, clk_put() was called for an enabled clock, which violates the API (see documentation for clk_put() in include/linux/clk.h) - In the error path of the probe function, clk_put() could be called twice for the same clock. In order to clean this up, use the managed function devm_clk_get() and store the pointer to the clk in the driver data. Fixes: baffab28 ('ARM: Orion: fix driver probe error handling with respect to clk') Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by:
-
- 28 Mar, 2017 4 commits
-
-
Masahiro Yamada authored
Because SUPPORT_15BITECC is defined, the following is dead code: #elif SUPPORT_8BITECC iowrite32(8, denali->flash_reg + ECC_CORRECTION); #endif Such ifdefs are useless and unacceptable coding style. These writes are not needed in the first place since ECC_CORRECTION is set up by the nand_init() function. Signed-off-by:Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Masahiro Yamada authored
The write accesses to LOGICAL_PAGE_{DATA,SPARE}_SIZE have no effect because the Denali User's Guide says these registers are read-only. The hardware automatically multiplies the main/spare size by the number of devices and update LOGICAL_PAGE_{DATA,SPARE}_SIZE. Signed-off-by: -
Masahiro Yamada authored
Currently, the driver expects DEVICE_CONNECTED is automatically set by the hardware, but this feature is disabled in some cases. In such cases, it is the software's responsibility to set up the DEVICES_CONNECTED register. Signed-off-by:
-
Masahiro Yamada authored
The available configuration of the IP bus width is x8 or x16, so the possible value for denali->devnum is 1 or 2. If the value is 1, there is nothing to do. Fixup parameters only when denali->devnum is 2. Signed-off-by:
-
- 27 Mar, 2017 3 commits
-
-
Masahiro Yamada authored
Collect multi NAND fixups into a helper function instead of scattering them in denali_init(). I am rewording the comment block to clearly explain what is called "multi device". Signed-off-by:
-
Masahiro Yamada authored
This will allow nand_dt_init() to parse DT properties in the NAND controller device node. Signed-off-by:
-
Masahiro Yamada authored
The denali_init() needs to setup a bunch of parameters of nand_chip. Replace denali->nand.(member) with chip->(member) for shorter code. Signed-off-by:
-
- 24 Mar, 2017 11 commits
-
-
Masahiro Yamada authored
Set Features (0xEF) command toggles the R/B# pin after 4 sub feature parameters are written. Currently, nand_command(_lp) calls chip->dev_ready immediately after the address cycle because NAND_CMD_SET_FEATURES falls into default: label. No wait is needed at this point. If you see nand_onfi_set_features(), R/B# is already cared by the chip->waitfunc call. Signed-off-by:
-
Masahiro Yamada authored
Read ID (0x90) command does not toggle the R/B# pin. Without this patch, NAND_CMD_READID falls into the default: label, then R/B# is checked by chip->dev_ready(). Signed-off-by:
-
Masahiro Yamada authored
The page number is generally stored in an integer type variable. The uint16_t does not have enough width. I see no reason to use uint32_t for other members, either. Just use int. Signed-off-by:
-
Masahiro Yamada authored
The Denali NAND controller IP has various customizable features. SoC vendors can choose desired functions when a delivery RTL is created. It means there are several variants for this IP. For example, the Intel version is equipped with 32bit DMA, whereas the IP for UniPhier SoC family with 64bit DMA. This driver was originally written for some Intel platforms with Intel specific things hard-coded. What is worse, the revision register of this IP does not work to distinguish such features. We need to do something to make the driver available for other SoCs. Let's introduce a caps member to the denali_nand_info structure to switch on/off various features. Also, add struct denali_dt_data to store the capability associated with compatible string. Boris suggested this approach in discussion [1] instead of a new DT property for every feature. [1] https://lkml.org/lkml/2016/3/29/142Signed-off-by:
-
Masahiro Yamada authored
The interrupts are enabled by INTR_EN register, then asserted interrupts can be observed via INTR_STATUS register. The bit fields are identical between INTR_EN and INTR_STATUS, so we can merge the bit field macros. Likewise for DATA_INTR. Signed-off-by:
-
Masahiro Yamada authored
The same comment "Mapped io reg base address" for flash_reg and flash_mem probably due to the mistake of copy-paste work. Of course, the latter is not the register base address. Reword the comments using the terminology in the Denali User's Guide. Signed-off-by:
-
Masahiro Yamada authored
These members are not used at all. Signed-off-by:
-
Masahiro Yamada authored
This macro is defined twice in denali.c (around line 98 and line 651), so remove the second one. Signed-off-by:
-
Masahiro Yamada authored
All of these macros are not used at all. CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR is not used for anything but defining SCRATCH_REG_ADDR. The config option should go away as well. I am removing some register macros. They are not used, and do not exist in recent IP versions. Signed-off-by:
-
Masahiro Yamada authored
The nand_default_block_markbad() and scan_block_fast() use high level APIs to get access to the BBM. On the other hand, nand_block_bad (the default implementation of ->block_bad) calls the lower level ->cmdfunc hook. This prevents drivers from using ->ecc.read_oob() even if optimized read operation is implemented. Besides, some NAND controllers may protect the BBM with ECC. Signed-off-by:
-
Masahiro Yamada authored
Currently, it is valid to specify both "nand-ecc-step-size" and "nand-ecc-strength", but not allowed to set only one of them. This requirement has a conflict with "nand-ecc-maximize"; this flag is used when you want the driver to choose the best ECC strength. If "nand-ecc-maximize" is set, "nand-ecc-strength" is very likely to be unset. It would be possible to make the if-conditional more complex by adding the check for the NAND_ECC_MAXIMIZE flag, but I chose to drop the check entirely. I thought of the situation where the hardware has a fixed ECC step size (so it can be hard-coded in the driver), whereas the ECC strength is configurable by software. In that case, we may want to only set "nand-ecc-strength" (or "nand-ecc-maximize") in DT. Signed-off-by:
-
- 23 Mar, 2017 12 commits
-
-
Thomas Petazzoni authored
Since commit 4404d7d8 ("mtd: nand: fsmc: remove stale non-DT probe path"), the fsmc NAND driver only supports Device Tree probing, and therefore has a "depends on OF" in its Kconfig option. Due to this the #ifdef CONFIG_OF ... #endif condition in the driver code is no longer necessary. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Thomas Petazzoni authored
These definitions are not used anywhere in the driver, so remove them. Signed-off-by:
-
Thomas Petazzoni authored
This commit switches the fsmc_nand driver from clk_get() to devm_clk_get(), which saves a few clk_put(). Signed-off-by:
-
Thomas Petazzoni authored
Since the driver now only supports DT probing, it doesn't make a lot of sense to have a private data structure called platform_data, fill it in with information coming from the DT, and then copying this into the driver-specific structure fsmc_nand_data. So instead, we remove fsmc_nand_platform_data entirely, and have fsmc_nand_probe_config_dt() fill in the fsmc_nand_data structure directly. This requires calling fsmc_nand_probe_config_dt() after fsmc_nand_data has been allocated instead of before. Also, as an added bonus, we now propagate properly the return value of fsmc_nand_probe_config_dt() instead of returning -ENODEV on failure. The error message is also removed, since it no longer made any sense. Signed-off-by:
-
Thomas Petazzoni authored
It is already done a few lines before. Signed-off-by:
-
Thomas Petazzoni authored
The ->partitions and ->nr_partitions fields of struct fsmc_nand_platform_data are never set anywhere, so they are always NULL/0. The corresponding fields in 'struct fsmc_nand_data' are set to the value of the same fields in fsmc_nand_platform_data, i.e NULL/0. Therefore, we remove those two fields, and pass NULL/0 directly to mtd_device_register(), like many other NAND drivers already do. At the same time, we remove the comment about the fact that we pass partition info, since we are no longer doing this. Signed-off-by:
-
Thomas Petazzoni authored
The read_dma_priv and write_dma_priv fields of fsmc_nand_platform_data are never set, so this commit removes them. Signed-off-by:
-
Thomas Petazzoni authored
host->select_chip used to point to the ->select_bank() function provided by the platform data, but the latter no longer exists. Therefore host->select_chip is always NULL. Due to this, the fsmc_select_chip() does nothing, except: chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); when chipnr is -1, which is exactly what the default implementation of ->select_chip() does in the NAND framework. So, this commit kills fsmc_select_chip() entirely. Signed-off-by:
-
Thomas Petazzoni authored
Since commit 4404d7d8 ("mtd: nand: fsmc: remove stale non-DT probe path"), only DT probing is used for the fsmc_nand driver. Due to this, the ->select_bank() field of fsmc_nand_platform_data is never used, so this commit gets rid of it. Signed-off-by:
-
Thomas Petazzoni authored
This commit simply moves the "struct fsmc_nand_data" definition to be towards the beginning of the file, with the other defines and type definitions, instead of in the middle of the driver code. This is much more consistent with what most Linux drivers do. Signed-off-by:
-
Thomas Petazzoni authored
In commit eea62819 ("mtd: Add device-tree support to fsmc_nand"), Device Tree support was added to the fmsc_nand driver. However, this code has a bug in how it handles the bank-width DT property to set the bus width. Indeed, in the function fsmc_nand_probe_config_dt() that parses the Device Tree, it sets pdata->width to either 8 or 16 depending on the value of the bank-width DT property. Then, the ->probe() function will test if pdata->width is equal to FSMC_NAND_BW16 (which is 2) to set NAND_BUSWIDTH_16 in nand->options. Therefore, with the DT probing, this condition will never match. This commit fixes that by removing the "width" field from fsmc_nand_platform_data and instead have the fsmc_nand_probe_config_dt() function directly set the appropriate nand->options value. It is worth mentioning that if this commit gets backported to older kernels, prior to the drop of non-DT probing, then non-DT probing will be broken because nand->options will no longer be set to NAND_BUSWIDTH_16. Fixes: eea62819 ("mtd: Add device-tree support to fsmc_nand") Signed-off-by:
-
Dan Carpenter authored
We should be return -ENOMEM instead of success. Fixes: 626994e0 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
- 16 Mar, 2017 6 commits
-
-
Christophe Leroy authored
On some hardware, the nCE signal is wired to the ChipSelect associated to bus address of the NAND, so it is automatically driven during the memory access and it is not managed by a GPIO. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by:
Marek Vasut <marek.vasut@gmail.com> Signed-off-by:
-
Alison Wang authored
As NAND support for Freescale/NXP IFC controller is available on LS1021A, the dependency for LS1021A is added. LS1021A is an earlier product and is not compatible with later LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A. Signed-off-by:
Alison Wang <alison.wang@nxp.com> Signed-off-by:
-
Alison Wang authored
As Freescale/NXP IFC controller is available on LS1021A, the dependency for LS1021A is added. LS1021A is an earlier product and is not compatible with later LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A. Signed-off-by:
-
Boris Brezillon authored
do_dma() uses an int to pass the DMA data direction information and pass the same value to dmaengine_prep_slave_sg(). Currently, DMA_{FROM,TO}_DEVICE match DMA_{DEV_TO_MEM,MEM_TO_DEV} definitions so it works fine, but assuming this will always be the case is not safe. Enforce enum dma_data_direction type in the function prototype and make the enum dma_data_direction -> enum dma_transfer_direction conversion explicit. Reported-by:Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
-
Colin Ian King authored
trivial fix to spelling mistake in NS_ERR error message Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
-
Philipp Zabel authored
As of commit bb475230 ("reset: make optional functions really optional"), the reset framework API calls use NULL pointers to describe optional, non-present reset controls. This allows to return errors from devm_reset_control_get_optional and to call reset_control_(de)assert unconditionally. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
- 08 Mar, 2017 1 commit
-
-
Boris Brezillon authored
All Hynix MLC NANDs produced with the 1x nm process support read-retry. This read retry implementation should also be re-usable for other Hynix NANDs, but the method to retrieve the read-retry parameters from the read-retry OTP area might change a bit (some NANDs are even using a fixed set of values instead of retrieving those information from the OTP area). Signed-off-by:
-
