Replace "fallthru" with a proper "fall through" annotation.

This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace "fallthru" with a proper "fall through" annotation.

This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When splitting a GSO segment that consists of encapsulated packets, the
skb->mac_len of the segments can end up being set wrong, causing packet
drops in particular when using act_mirred and ifb interfaces in
combination with a qdisc that splits GSO packets.

This happens because at the time skb_segment() is called, network_header
will point to the inner header, throwing off the calculation in
skb_reset_mac_len(). The network_header is subsequently adjust by the
outer IP gso_segment handlers, but they don't set the mac_len.

Fix this by adding skb_reset_mac_len() calls to both the IPv4 and IPv6
gso_segment handlers, after they modify the network_header.

Many thanks to Eric Dumazet for his help in identifying the cause of
the bug.
Acked-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the Device Tree is not providing the per-port interrupts, do not fail
during b53_srab_irq_enable() but instead bail out gracefully. The SRAB driver
is used on the BCM5301X (Northstar) platforms which do not yet have the SRAB
interrupts wired up.

Fixes: 16994374 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jason Wang says:

====================
vhost_net TX batching

This series tries to batch submitting packets to underlayer socket
through msg_control during sendmsg(). This is done by:

1) Doing userspace copy inside vhost_net
2) Build XDP buff
3) Batch at most 64 (VHOST_NET_BATCH) XDP buffs and submit them once
   through msg_control during sendmsg().
4) Underlayer sockets can use XDP buffs directly when XDP is enalbed,
   or build skb based on XDP buff.

For the packet that can not be built easily with XDP or for the case
that batch submission is hard (e.g sndbuf is limited). We will go for
the previous slow path, passing iov iterator to underlayer socket
through sendmsg() once per packet.

This can help to improve cache utilization and avoid lots of indirect
calls with sendmsg(). It can also co-operate with the batching support
of the underlayer sockets (e.g the case of XDP redirection through
maps).

Testpmd(txonly) in guest shows obvious improvements:

Test                /+pps%
XDP_DROP on TAP     /+44.8%
XDP_REDIRECT on TAP /+29%
macvtap (skb)       /+26%

Netperf TCP_STREAM TX from guest shows obvious improvements on small
packet:

    size/session/+thu%/+normalize%
       64/     1/   +2%/    0%
       64/     2/   +3%/   +1%
       64/     4/   +7%/   +5%
       64/     8/   +8%/   +6%
      256/     1/   +3%/    0%
      256/     2/  +10%/   +7%
      256/     4/  +26%/  +22%
      256/     8/  +27%/  +23%
      512/     1/   +3%/   +2%
      512/     2/  +19%/  +14%
      512/     4/  +43%/  +40%
      512/     8/  +45%/  +41%
     1024/     1/   +4%/    0%
     1024/     2/  +27%/  +21%
     1024/     4/  +38%/  +73%
     1024/     8/  +15%/  +24%
     2048/     1/  +10%/   +7%
     2048/     2/  +16%/  +12%
     2048/     4/    0%/   +2%
     2048/     8/    0%/   +2%
     4096/     1/  +36%/  +60%
     4096/     2/  -11%/  -26%
     4096/     4/    0%/  +14%
     4096/     8/    0%/   +4%
    16384/     1/   -1%/   +5%
    16384/     2/    0%/   +2%
    16384/     4/    0%/   -3%
    16384/     8/    0%/   +4%
    65535/     1/    0%/  +10%
    65535/     2/    0%/   +8%
    65535/     4/    0%/   +1%
    65535/     8/    0%/   +3%

Please review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements XDP batching for vhost_net. The idea is first to
try to do userspace copy and build XDP buff directly in vhost. Instead
of submitting the packet immediately, vhost_net will batch them in an
array and submit every 64 (VHOST_NET_BATCH) packets to the under layer
sockets through msg_control of sendmsg().

When XDP is enabled on the TUN/TAP, TUN/TAP can process XDP inside a
loop without caring GUP thus it can do batch map flushing. When XDP is
not enabled or not supported, the underlayer socket need to build skb
and pass it to network core. The batched packet submission allows us
to do batching like netif_receive_skb_list() in the future.

This saves lots of indirect calls for better cache utilization. For
the case that we can't so batching e.g when sndbuf is limited or
packet size is too large, we will go for usual one packet per
sendmsg() way.

Doing testpmd on various setups gives us:

Test                /+pps%
XDP_DROP on TAP     /+44.8%
XDP_REDIRECT on TAP /+29%
macvtap (skb)       /+26%

Netperf tests shows obvious improvements for small packet transmission:

size/session/+thu%/+normalize%
   64/     1/   +2%/    0%
   64/     2/   +3%/   +1%
   64/     4/   +7%/   +5%
   64/     8/   +8%/   +6%
  256/     1/   +3%/    0%
  256/     2/  +10%/   +7%
  256/     4/  +26%/  +22%
  256/     8/  +27%/  +23%
  512/     1/   +3%/   +2%
  512/     2/  +19%/  +14%
  512/     4/  +43%/  +40%
  512/     8/  +45%/  +41%
 1024/     1/   +4%/    0%
 1024/     2/  +27%/  +21%
 1024/     4/  +38%/  +73%
 1024/     8/  +15%/  +24%
 2048/     1/  +10%/   +7%
 2048/     2/  +16%/  +12%
 2048/     4/    0%/   +2%
 2048/     8/    0%/   +2%
 4096/     1/  +36%/  +60%
 4096/     2/  -11%/  -26%
 4096/     4/    0%/  +14%
 4096/     8/    0%/   +4%
16384/     1/   -1%/   +5%
16384/     2/    0%/   +2%
16384/     4/    0%/   -3%
16384/     8/    0%/   +4%
65535/     1/    0%/  +10%
65535/     2/    0%/   +8%
65535/     4/    0%/   +1%
65535/     8/    0%/   +3%
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implement TUN_MSG_PTR msg_control type. This type allows
the caller to pass an array of XDP buffs to tuntap through ptr field
of the tun_msg_control. Tap will build skb through those XDP buffers.

This will avoid lots of indirect calls thus improves the icache
utilization and allows to do XDP batched flushing when doing XDP
redirection.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implement TUN_MSG_PTR msg_control type. This type allows
the caller to pass an array of XDP buffs to tuntap through ptr field
of the tun_msg_control. If an XDP program is attached, tuntap can run
XDP program directly. If not, tuntap will build skb and do a fast
receiving since part of the work has been done by vhost_net.

This will avoid lots of indirect calls thus improves the icache
utilization and allows to do XDP batched flushing when doing XDP
redirection.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces to a new tun/tap specific msg_control:

#define TUN_MSG_UBUF 1
#define TUN_MSG_PTR  2
struct tun_msg_ctl {
       int type;
       void *ptr;
};

This allows us to pass different kinds of msg_control through
sendmsg(). The first supported type is ubuf (TUN_MSG_UBUF) which will
be used by the existed vhost_net zerocopy code. The second is XDP
buff, which allows vhost_net to pass XDP buff to TUN. This could be
used to implement accepting an array of XDP buffs from vhost_net in
the following patches.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will allow adding batch flushing on top.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch split out XDP logic into a single function. This make it to
be reused by XDP batching path in the following patch.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we're sure not to go native XDP, there's no need for several things
like bh and rcu stuffs. So this patch introduces a helper to build skb
and hold page refcnt. When we found we will go through skb path, build
skb directly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need to duplicate page get logic in each action. So this
patch tries to get page and calculate the offset before processing XDP
actions (except for XDP_DROP), and undo them when meet errors (we
don't care the performance on errors). This will be used for factoring
out XDP logic.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch move the bh enabling a little bit earlier, this will be
used for factoring out the core XDP logic of tuntap.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces a new sock flag - SOCK_XDP. This will be used
for notifying the upper layer that XDP program is attached on the
lower socket, and requires for extra headroom.

TUN will be the first user.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc_sap_close() is called by llc_sap_put() which
could be called in BH context in llc_rcv(). We can't
block in BH.

There is no reason to block it here, kfree_rcu() should
be sufficient.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The socket option will be enabled by default to ensure current behaviour
is not changed. This is the same for the IPv4 version.

A socket bound to in6addr_any and a specific port will receive all traffic
on that port. Analogue to IP_MULTICAST_ALL, disable this behaviour, if
one or more multicast groups were joined (using said socket) and only
pass on multicast traffic from groups, which were explicitly joined via
this socket.

Without this option disabled a socket (system even) joined to multiple
multicast groups is very hard to get right. Filtering by destination
address has to take place in user space to avoid receiving multicast
traffic from other multicast groups, which might have traffic on the same
port.

The extension of the IP_MULTICAST_ALL socketoption to just apply to ipv6,
too, is not done to avoid changing the behaviour of current applications.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-By: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hauke Mehrtens says:

====================
Add support for Lantiq / Intel vrx200 network

This adds basic support for the GSWIP (Gigabit Switch) found in the
VRX200 SoC.
There are different versions of this IP core used in different SoCs, but
this driver was currently only tested on the VRX200 SoC line, for other
SoCs this driver probably need some adoptions to work.

I also plan to add Layer 2 offloading to the DSA driver and later also
layer 3 offloading which is supported by the PPE HW block.

All these patches should go through the net-next tree.

This depends on the patch "MIPS: lantiq: dma: add dev pointer" which
should go into 4.19.

Changes since:
v2:
 * Send patch "MIPS: lantiq: dma: add dev pointer" separately
 * all: removed return in register write functions
 * switch: uses phylink
 * switch: uses hardware MDIO auto polling
 * switch: use usleep_range() in MDIO busy check
 * switch: configure MDIO bus to 2.5 MHz
 * switch: disable xMII link when it is not used
 * Ethernet: use NAPI for TX cleanups
 * Ethernet: enable clock in open callback
 * Ethernet: improve skb allocation
 * Ethernet: use net_dev->stats

v1:
 * Add "MIPS: lantiq: dma: add dev pointer"
 * checkpatch fixes a all patches
 * Added binding documentation
 * use readx_poll_timeout function and ETIMEOUT error code
 * integrate GPHY firmware loading into DSA driver
 * renamed to NET_DSA_LANTIQ_GSWIP
 * removed some needed casts
 * added of_device_id.data information about the detected switch
 * fixed John's email address
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.

The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.

The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the binding for the GSWIP (Gigabit switch) core found in the
xrx200 / VR9 Lantiq / Intel SoC.

This part takes care of the switch, MDIO bus, and loading the FW into
the embedded GPHYs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This drives the PMAC between the GSWIP Switch and the CPU in the VRX200
SoC. This is currently only the very basic version of the Ethernet
driver.

When the DMA channel is activated we receive some packets which were
send to the SoC while it was still in U-Boot, these packets have the
wrong header. Resetting the IP cores did not work so we read out the
extra packets at the beginning and discard them.

This also adapts the clock code in sysctrl.c to use the default name of
the device node so that the driver gets the correct clock. sysctrl.c
should be replaced with a proper common clock driver later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the binding for the PMAC core between the CPU and the GSWIP
switch found on the xrx200 / VR9 Lantiq / Intel SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This handles the tag added by the PMAC on the VRX200 SoC line.

The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.

This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a DMA channel is opened the IRQ should not get activated
automatically, this allows it to pull data out manually without the help
of interrupts. This is needed for a workaround in the vrx200 Ethernet
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document is stale, let's remove it.

Remove TCP congestion document.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar with commit 72f6d71e ("vxlan: add ttl inherit support"),
currently ttl == 0 means "use whatever default value" on geneve instead
of inherit inner ttl. To respect compatibility with old behavior, let's
add a new IFLA_GENEVE_TTL_INHERIT for geneve ttl inherit support.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm nouveau fixes from Dave Airlie:
 "I'm sending this separately as it's a bit larger than I generally like
  for one driver, but it does contain a bunch of make my nvidia laptop
  not die (runpm) and a bunch to make my docking station and monitor
  display stuff (mst) fixes.

  Lyude has spent a lot of time on these, and we are putting the fixes
  into distro kernels as well asap, as it helps a bunch of standard
  Lenovo laptops, so I'm fairly happy things are better than they were
  before these patches, but I decided to split them out just for
  clarification"

* tag 'drm-fixes-2018-09-12' of git://anongit.freedesktop.org/drm/drm:
  drm/nouveau/disp/gm200-: enforce identity-mapped SOR assignment for LVDS/eDP panels
  drm/nouveau/disp: fix DP disable race
  drm/nouveau/disp: move eDP panel power handling
  drm/nouveau/disp: remove unused struct member
  drm/nouveau/TBDdevinit: don't fail when PMU/PRE_OS is missing from VBIOS
  drm/nouveau/mmu: don't attempt to dereference vmm without valid instance pointer
  drm/nouveau: fix oops in client init failure path
  drm/nouveau: Fix nouveau_connector_ddc_detect()
  drm/nouveau/drm/nouveau: Don't forget to cancel hpd_work on suspend/unload
  drm/nouveau/drm/nouveau: Prevent handling ACPI HPD events too early
  drm/nouveau: Reset MST branching unit before enabling
  drm/nouveau: Only write DP_MSTM_CTRL when needed
  drm/nouveau: Remove useless poll_enable() call in drm_load()
  drm/nouveau: Remove useless poll_disable() call in switcheroo_set_state()
  drm/nouveau: Remove useless poll_enable() call in switcheroo_set_state()
  drm/nouveau: Fix deadlocks in nouveau_connector_detect()
  drm/nouveau/drm/nouveau: Use pm_runtime_get_noresume() in connector_detect()
  drm/nouveau/drm/nouveau: Fix deadlock with fb_helper with async RPM requests
  drm/nouveau: Remove duplicate poll_enable() in pmops_runtime_suspend()
  drm/nouveau/drm/nouveau: Fix bogus drm_kms_helper_poll_enable() placement

The MV88E6xxx can have external PHYs attached to certain ports and those
PHYs could even be on different MDIO bus than the one within the switch.
This patch makes sure that ports with such PHYs are configured correctly
according to the information provided by the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

DIV_ROUND_UP has implemented the code-opened function. Therefore, just
replace the implementation with DIV_ROUND_UP.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_pull_bc_msg':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:907:6: warning:
 variable 'fw_mbx' set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_issue_bc_post':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:939:16: warning:
 variable 'hdr_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix up several Kconfig dependencies in netfilter, from Martin Willi
    and Florian Westphal.

 2) Memory leak in be2net driver, from Petr Oros.

 3) Memory leak in E-Switch handling of mlx5 driver, from Raed Salem.

 4) mlx5_attach_interface needs to check for errors, from Huy Nguyen.

 5) tipc_release() needs to orphan the sock, from Cong Wang.

 6) Need to program TxConfig register after TX/RX is enabled in r8169
    driver, not beforehand, from Maciej S. Szmigiero.

 7) Handle 64K PAGE_SIZE properly in ena driver, from Netanel Belgazal.

 8) Fix crash regression in ip_do_fragment(), from Taehee Yoo.

 9) syzbot can create conditions where kernel log is flooded with
    synflood warnings due to creation of many listening sockets, fix
    that. From Willem de Bruijn.

10) Fix RCU issues in rds socket layer, from Cong Wang.

11) Fix vlan matching in nfp driver, from Pieter Jansen van Vuuren.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
  nfp: flower: reject tunnel encap with ipv6 outer headers for offloading
  nfp: flower: fix vlan match by checking both vlan id and vlan pcp
  tipc: check return value of __tipc_dump_start()
  s390/qeth: don't dump past end of unknown HW header
  s390/qeth: use vzalloc for QUERY OAT buffer
  s390/qeth: switch on SG by default for IQD devices
  s390/qeth: indicate error when netdev allocation fails
  rds: fix two RCU related problems
  r8169: Clear RTL_FLAG_TASK_*_PENDING when clearing RTL_FLAG_TASK_ENABLED
  erspan: fix error handling for erspan tunnel
  erspan: return PACKET_REJECT when the appropriate tunnel is not found
  tcp: rate limit synflood warnings further
  MIPS: lantiq: dma: add dev pointer
  netfilter: xt_hashlimit: use s->file instead of s->private
  netfilter: nfnetlink_queue: Solve the NFQUEUE/conntrack clash for NF_REPEAT
  netfilter: cttimeout: ctnl_timeout_find_get() returns incorrect pointer to type
  netfilter: conntrack: timeout interface depend on CONFIG_NF_CONNTRACK_TIMEOUT
  netfilter: conntrack: reset tcp maxwin on re-register
  qmi_wwan: Support dynamic config on Quectel EP06
  ethernet: renesas: convert to SPDX identifiers
  ...

Add support for entries which are "sticky", i.e. will not change their port
if they show up from a different one. A new ndm flag is introduced for that
purpose - NTF_STICKY. We allow to set it only to non-local entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Preparing for phylib linkmodes

phylib currently makes us of a u32 bitmap for advertising, supported,
and link partner capabilities. For a long time, this has been
sufficient, for devices up to 1Gbps. With more MAC/PHY combinations
now supporting speeds greater than 1Gbps, we have run out of
bits. There is the need to replace this u32 with an
__ETHTOOL_DECLARE_LINK_MODE_MASK, which makes use of linux's generic
bitmaps.

This patchset does some of the work preparing for this change. A few
cleanups are applied to PHY drivers. Some MAC drivers directly access
members of phydev which are going to change type. These patches adds
some helpers and swaps MAC drivers to use them, mostly dealing with
Pause configuration.

v3:
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Add missing at in commit message
Change Subject of patch 5
Fix return in from phy_set_asym_pause
Fix kerneldoc in phy_set_pause

v2:
Fixup bad indentation in tg3.c
Rename phy_support_pause() to phy_support_sym_pause()
Also trigger autoneg if the advertising settings have changed.
Rename phy_set_pause() to phy_set_sym_pause()
Use the bcm63xx_enet.c logic, not fec_main.c for validating pause
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>