Limit the acceptance of component name passed to cmd_flash_update() to
match one of the versions returned by info_get(), marked by version type.
This makes things clearer and enforces 1:1 mapping between exposed
version and accepted flash component.

Check VERSION_TYPE_COMPONENT version type during cmd_flash_update()
execution by calling info_get() with different "req" context.
That causes info_get() to lookup the component name instead of
filling-up the netlink message.

Remove "UPDATE_COMPONENT" flag which becomes used.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the only component user which is netdevsim. It uses component named
"fw.mgmt" in selftests. So add this version to info_get() output with
version type component.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Whenever the driver is called by his info_get() op, it may put multiple
version names and values to the netlink message. Extend by additional
helper devlink_info_version_running/stored_put_ext() that allows to
specify a version type that indicates when particular version name
represents a flash component.

This is going to be used in follow-up patch calling info_get() during
flash update command checking if version with this the version type
exists.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Assinging will drop all previous tests.

Fixes: b690842d ("selftests/net: test l2 tunnel TOS/TTL inheriting")
Signed-off-by: Adel Abouchaev <adel.abushaev@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220824184351.3759862-1-adel.abushaev@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

qdisc_reset() is clearing qdisc->q.qlen and qdisc->qstats.backlog
_after_ calling qdisc->ops->reset. There is no need to clear them
again in the specific reset function.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220824005231.345727-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

is_post_ct_flow() function will process only ct_state ESTABLISHED,
then offload_pre_check() function will check FLOW_DISSECTOR_KEY_CT flag.
When config tc filter match ct_state(0/0x3f), dissector->used_keys
with FLOW_DISSECTOR_KEY_CT bit, function offload_pre_check() will
return false, so not offload. This is a special case that can be handled
safely.

Therefore, modify to let initial packet which won't go through conntrack
can be offloaded, as long as the cared ct fields are all zero.
Signed-off-by: Wenjuan Geng <wenjuan.geng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220823090122.403631-1-simon.horman@corigine.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Introduce a simple helper function to replace a common pattern.
When accessing the GRO header, we fetch the pointer from frag0,
then test its validity and fetch it from the skb when necessary.

This leads to the pattern
skb_gro_header_fast -> skb_gro_header_hard -> skb_gro_header_slow
recurring many times throughout GRO code.

This patch replaces these patterns with a single inlined function
call, improving code readability.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220823071034.GA56142@debianSigned-off-by: Paolo Abeni <pabeni@redhat.com>

As all callbacks are converted now, fix the text reflecting that change.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220823070213.1008956-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Joanne Koong says:

====================
Add a second bind table hashed by port and address

Currently, there is one bind hashtable (bhash) that hashes by port only.
This patchset adds a second bind table (bhash2) that hashes by port and
address.

The motivation for adding bhash2 is to expedite bind requests in situations
where the port has many sockets in its bhash table entry (eg a large number
of sockets bound to different addresses on the same port), which makes checking
bind conflicts costly especially given that we acquire the table entry spinlock
while doing so, which can cause softirq cpu lockups and can prevent new tcp
connections.

We ran into this problem at Meta where the traffic team binds a large number
of IPs to port 443 and the bind() call took a significant amount of time
which led to cpu softirq lockups, which caused packet drops and other failures
on the machine.

When experimentally testing this on a local server for ~24k sockets bound to
the port, the results seen were:

ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds

ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds

The additions to the initial bhash2 submission [0] are:
* Updating bhash2 in the cases where a socket's rcv saddr changes after it has
* been bound
* Adding locks for bhash2 hashbuckets

[0] https://lore.kernel.org/netdev/20220520001834.2247810-1-kuba@kernel.org/

v3: https://lore.kernel.org/netdev/20220722195406.1304948-2-joannelkoong@gmail.com/
v2: https://lore.kernel.org/netdev/20220712235310.1935121-1-joannelkoong@gmail.com/
v1: https://lore.kernel.org/netdev/20220623234242.2083895-2-joannelkoong@gmail.com/
====================

Link: https://lore.kernel.org/r/20220822181023.3979645-1-joannelkoong@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds 2 new tests: sk_bind_sendto_listen and
sk_connect_zero_addr.

The sk_bind_sendto_listen test exercises the path where a socket's
rcv saddr changes after it has been added to the binding tables,
and then a listen() on the socket is invoked. The listen() should
succeed.

The sk_bind_sendto_listen test is copied over from one of syzbot's
tests: https://syzkaller.appspot.com/x/repro.c?x=1673a38df00000

The sk_connect_zero_addr test exercises the path where the socket was
never previously added to the binding tables and it gets assigned a
saddr upon a connect() to address 0.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This test populates the bhash table for a given port with
MAX_THREADS * MAX_CONNECTIONS sockets, and then times how long
a bind request on the port takes.

When populating the bhash table, we create the sockets and then bind
the sockets to the same address and port (SO_REUSEADDR and SO_REUSEPORT
are set). When timing how long a bind on the port takes, we bind on a
different address without SO_REUSEPORT set. We do not set SO_REUSEPORT
because we are interested in the case where the bind request does not
go through the tb->fastreuseport path, which is fragile (eg
tb->fastreuseport path does not work if binding with a different uid).

To run the script:
    Usage: ./bind_bhash.sh [-6 | -4] [-p port] [-a address]
	    6: use ipv6
	    4: use ipv4
	    port: Port number
	    address: ip address

Without any arguments, ./bind_bhash.sh defaults to ipv6 using ip address
"2001:0db8:0:f101::1" on port 443.

On my local machine, I see:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds

ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The current bind hashtable (bhash) is hashed by port only.
In the socket bind path, we have to check for bind conflicts by
traversing the specified port's inet_bind_bucket while holding the
hashbucket's spinlock (see inet_csk_get_port() and
inet_csk_bind_conflict()). In instances where there are tons of
sockets hashed to the same port at different addresses, the bind
conflict check is time-intensive and can cause softirq cpu lockups,
as well as stops new tcp connections since __inet_inherit_port()
also contests for the spinlock.

This patch adds a second bind table, bhash2, that hashes by
port and sk->sk_rcv_saddr (ipv4) and sk->sk_v6_rcv_saddr (ipv6).
Searching the bhash2 table leads to significantly faster conflict
resolution and less time holding the hashbucket spinlock.

Please note a few things:
* There can be the case where the a socket's address changes after it
has been bound. There are two cases where this happens:

  1) The case where there is a bind() call on INADDR_ANY (ipv4) or
  IPV6_ADDR_ANY (ipv6) and then a connect() call. The kernel will
  assign the socket an address when it handles the connect()

  2) In inet_sk_reselect_saddr(), which is called when rebuilding the
  sk header and a few pre-conditions are met (eg rerouting fails).

In these two cases, we need to update the bhash2 table by removing the
entry for the old address, and add a new entry reflecting the updated
address.

* The bhash2 table must have its own lock, even though concurrent
accesses on the same port are protected by the bhash lock. Bhash2 must
have its own lock to protect against cases where sockets on different
ports hash to different bhash hashbuckets but to the same bhash2
hashbucket.

This brings up a few stipulations:
  1) When acquiring both the bhash and the bhash2 lock, the bhash2 lock
  will always be acquired after the bhash lock and released before the
  bhash lock is released.

  2) There are no nested bhash2 hashbucket locks. A bhash2 lock is always
  acquired+released before another bhash2 lock is acquired+released.

* The bhash table cannot be superseded by the bhash2 table because for
bind requests on INADDR_ANY (ipv4) or IPV6_ADDR_ANY (ipv6), every socket
bound to that port must be checked for a potential conflict. The bhash
table is the only source of port->socket associations.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Modify the comment of input parameter of nlmsg_ and nla_ function.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220824013621.365103-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

davinci_mdio.c uses mdio bitbang APIs, so it should select
MDIO_BITBANG to prevent build errors.

arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_remove':
drivers/net/ethernet/ti/davinci_mdio.c:649: undefined reference to `free_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:545: undefined reference to `alloc_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_read':
drivers/net/ethernet/ti/davinci_mdio.c:236: undefined reference to `mdiobb_read'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_write':
drivers/net/ethernet/ti/davinci_mdio.c:253: undefined reference to `mdiobb_write'

Fixes: d04807b8 ("net: ethernet: ti: davinci_mdio: Add workaround for errata i2329")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ravi Gunasekaran <r-gunasekaran@ti.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Sudip Mukherjee (Codethink) <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20220824024216.4939-1-rdunlap@infradead.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Stephen Rothwell reported htmldocs warning when merging net-next tree:

Documentation/admin-guide/sysctl/net.rst:37: WARNING: Malformed table.
Text in column margin in table line 4.

========= =================== = ========== ==================
Directory Content               Directory  Content
========= =================== = ========== ==================
802       E802 protocol         mptcp     Multipath TCP
appletalk Appletalk protocol    netfilter Network Filter
ax25      AX25                  netrom     NET/ROM
bridge    Bridging              rose      X.25 PLP layer
core      General parameter     tipc      TIPC
ethernet  Ethernet protocol     unix      Unix domain sockets
ipv4      IP version 4          x25       X.25 protocol
ipv6      IP version 6
========= =================== = ========== ==================

The warning above is caused by cells in second "Content" column of
/proc/sys/net subdirectory table which are in column margin.

Align these cells against the column header to fix the warning.

Link: https://lore.kernel.org/linux-next/20220823134905.57ed08d5@canb.auug.org.au/
Fixes: 1202cdd6 ("Remove DECnet support from kernel")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://lore.kernel.org/r/20220824035804.204322-1-bagasdotme@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Heiner Kallweit says:

====================
r8169: remove support for few unused chip versions

There's a number of chip versions that apparently never made it to the
mass market. Detection of these chip versions has been disabled for
few kernel versions now and nobody complained. Therefore remove
support for these chip versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.

v3:
- rebase patch
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.

v2:
- fix a typo: RTL_GIGA_MAC_VER_40 -> RTL_GIGA_MAC_VER_50
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detection of these chip versions has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx5-updates-2022-08-22

Roi Dayan Says:
===============
Add support for SF tunnel offload

Mlx5 driver only supports VF tunnel offload.
To add support for SF tunnel offload the driver needs to:
1. Add send-to-vport metadata matching rules like done for VFs.
2. Set an indirect table for SF vport, same as VF vport.

info smaller sub functions for better maintainability.

rules from esw init phase to representor load phase.
SFs could be created after esw initialized and thus the send-to-vport
meta rules would not be created for those SFs.
By moving the creation of the rules to representor load phase
we ensure creating the rules also for SFs created later.

===============

Lama Kayal Says:
================
Make flow steering API loosely coupled from mlx5e_priv, in a manner to
introduce more readable and maintainable modules.

Make TC's private, let mlx5e_flow_steering struct be dynamically allocated,
and introduce its API to maintain the code via setters and getters
instead of publicly exposing it.

Introduce flow steering debug macros to provide an elegant finish to the
decoupled flow steering API, where errors related to flow steering shall
be reported via them.

All flow steering related files will drop any coupling to mlx5e_priv,
instead they will get the relevant members as input. Among these,
fs_tt_redirect, fs_tc, and arfs.
================

Issue found during code review. This bug has no impact as long as the
ks8851_net structure is the first element of the ks8851_net_spi structure.
As long as the offset to the ks8851_net struct is zero, the container_of()
macro is subtracting 0 and therefore no damage done. But if the
ks8851_net_spi struct is ever modified such that the ks8851_net struct
within it is no longer the first element of the struct, then the bug would
manifest itself and cause problems.

struct ks8851_net is contained within ks8851_net_spi.
ks is contained within kss.
kss is the priv_data of the netdev structure.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_md5sig_pool_populated can be read while another thread
changes its value.

The race has no consequence because allocations
are protected with tcp_md5sig_mutex.

This patch adds READ_ONCE() and WRITE_ONCE() to document
the race and silence KCSAN.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both <port> br_port_locked and <lag> interfaces's flag
offloading is supported. No new ABI is being added,
rather existing (port_param_set) API call gets extended.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>

V2:
  add missing receipents (linux-kernel, netdev)
Signed-off-by: David S. Miller <davem@davemloft.net>

Siddharth Vadapalli says:

====================
J7200: CPSW5G: Add support for QSGMII mode to am65-cpsw driver

Add support for QSGMII mode to am65-cpsw driver.

Change log:

v4-> v5:
1. Move ti,j7200-cpswxg-nuss compatible to the line above the
   ti,j721e-cpsw-nuss compatible.
2. Add allOf and move if-then statements within it to allow future if-then
   statements to be added easily.

v3 -> v4:
1. Update bindings to disallow ports based on compatible, instead of
   adding a new if/then statement for the new compatible.
2. Add Else-If condition for RMII mode in the set of supported interfaces.
   Support for RMII mode is already present in the driver and I had
   missed out adding a condition for RMII mode in the previous patches.

v2 -> v3:
1. In ti,k3-am654-cpsw-nuss.yaml, restrict if/then statement to port
   nodes.

v1 -> v2:
1. Add new compatible for CPSW5G in ti,k3-am654-cpsw-nuss.yaml and extend
   properties for new compatible.
2. Add extra_modes member to struct am65_cpsw_pdata to be used for QSGMII
   mode by new compatible.
3. Add check for phylink supported modes to ensure that only one phy mode
   is advertised as supported.
4. Check if extra_modes supports QSGMII mode in am65_cpsw_nuss_mac_config()
   for register write.
5. Add check for assigning port->sgmii_base only when extra_modes is valid.

v4: https://lore.kernel.org/r/20220816060139.111934-1-s-vadapalli@ti.com/
v3: https://lore.kernel.org/r/20220606110443.30362-1-s-vadapalli@ti.com/
v2: https://lore.kernel.org/r/20220602114558.6204-1-s-vadapalli@ti.com/
v1: https://lore.kernel.org/r/20220531113058.23708-1-s-vadapalli@ti.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In TI's J7200 SoC CPSW5G ports, each of the 4 ports can be configured
as a QSGMII main or QSGMII-SUB port. This configuration is performed
by phy-gmii-sel driver on invoking the phy_set_mode_ext() function.

It is necessary for the QSGMII main port to be configured before any of
the QSGMII-SUB interfaces are brought up. Currently, the QSGMII-SUB
interfaces come up before the QSGMII main port is configured.

Fix this by moving the call to phy_set_mode_ext() from
am65_cpsw_nuss_ndo_slave_open() to am65_cpsw_nuss_init_slave_ports(),
thereby ensuring that the QSGMII main port is configured before any of
the QSGMII-SUB ports are brought up.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CPSW5G in J7200 supports additional modes like QSGMII and SGMII.
Add new compatible for J7200 and enable QSGMII mode in am65-cpsw driver.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update bindings for TI K3 J7200 SoC which contains 5 ports (4 external
ports) CPSW5G module and add compatible for it.

Changes made:
    - Add new compatible ti,j7200-cpswxg-nuss for CPSW5G.
    - Extend pattern properties for new compatible.
    - Change maximum number of CPSW ports to 4 for new compatible.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes, gcc will optimize the function by spliting it to two or
more functions. In this case, kfree_skb_reason() is splited to
kfree_skb_reason and kfree_skb_reason.part.0. However, the
function/tracepoint trace_kfree_skb() in it needs the return address
of kfree_skb_reason().

This split makes the call chains becomes:
  kfree_skb_reason() -> kfree_skb_reason.part.0 -> trace_kfree_skb()

which makes the return address that passed to trace_kfree_skb() be
kfree_skb().

Therefore, introduce '__fix_address', which is the combination of
'__noclone' and 'noinline', and apply it to kfree_skb_reason() to
prevent to from being splited or made inline.

(Is it better to simply apply '__noclone oninline' to kfree_skb_reason?
I'm thinking maybe other functions have the same problems)

Meanwhile, wrap 'skb_unref()' with 'unlikely()', as the compiler thinks
it is likely return true and splits kfree_skb_reason().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wei Fang says:

====================
add interface mode select and RMII

From: Wei Fang <wei.fang@nxp.com>

The patches add the below feature support for both TJA1100 and
TJA1101 PHYs cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.
====================

Link: https://lore.kernel.org/r/20220822015949.1569969-1-wei.fang@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add below features support for both TJA1100 and TJA1101 cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

TJA110x REF_CLK can be configured as interface reference clock
intput or output when the RMII mode enabled. This patch add the
property to make the REF_CLK can be configurable.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Petr Machata says:

====================
mlxsw: Introduce modular system support by minimal driver

Vadim Pasternak writes:

This patchset adds line cards support in mlxsw_minimal, which is used
for monitoring purposes on BMC systems. The BMC is connected to the
ASIC over I2C bus, unlike the host CPU that is connected to the ASIC
via PCI bus.

The BMC system needs to be notified whenever line cards become active
or inactive, so that, for example, netdevs will be registered /
unregistered by mlxsw_minimal. However, traps cannot be generated
towards the BMC over the I2C bus. To overcome that, the I2C bus driver
(i.e., mlxsw_i2c) registers an handler for an IRQ that is fired upon
specific system wide changes, like line card activation and
deactivation.

The generated event is handled by mlxsw_core, which checks whether
anything changed in the state of available line cards. If a line card
becomes active or inactive, interested parties such as mlxsw_minimal
are notified via their registered line card event callback.

Patch set overview:

Patches #1 is preparations.

Patches #2-#3 extend mlxsw_core with an infrastructure to handle the
	previously mentioned system events.

Patch #4 extends the I2C bus driver to register an handler for the IRQ
	fired upon specific system wide changes.

Patches #5-#8 gradually add line cards support in mlxsw_minimal by
	dynamically registering / unregistering netdevs for ports found on
	line cards, whenever a line card becomes active / inactive.
====================

Link: https://lore.kernel.org/r/cover.1661093502.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement line card operation callbacks got_active() / got_inactive().
The purpose of these callback to create / remove line card ports after
line card is getting active / inactive.

Implement line ports_remove_selected() callback to support line card
un-provisioning flow through 'devlink'.

Add line card operation registration and de-registration APIs.

Add module offset for line card. Offset for main board iz zero.
For line card in slot #n offset is calculated as (#n - 1) multiplied by
maximum modules number.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The interfaces for ports found on line card are created and removed
dynamically after line card is getting active or inactive.

Introduce per line card array with module to port mapping.
For each port get 'slot_index' through PMLP register and set port
mapping for the relevant [slot_index][module] entry.

Split module and port allocation into separate routines.

Split per line card port creation and removing into separate routines.
Motivation to re-use these routines for line card operations.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Perform ports allocation in a separate routine.
Motivation is to re-use this routine for ports found on line cards.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add 'slot_index' field to port structure.
Replace zero slot_index argument with 'slot_index' in 'ethtool'
related APIs.
Add 'slot_index' argument to port initialization and
de-initialization related APIs.

Motivation is to prepare minimal driver for modular system support.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend i2c bus driver with interrupt handler to support system specific
hotplug events, related to line card state change.

Provide system IRQ line for interrupt handler. IRQ line Id could be
provided through the platform data if available, or could be set to the
default value.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add line card system event handler. Register it with core. It is
triggered by system interrupts raised from chassis programmable logic
devices to CPU. The purpose is to handle line card state changes over
I2C bus.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>