Use a more correct calculation for highspeed bit times.

  http://bugzilla.kernel.org/show_bug.cgi?id=3604

This sort if thing might start to make a difference now that the high
speed periodic scheduler is more complete -- and even getting used.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as556) adds support for unbinding the usb_generic "driver".
That driver only binds to USB devices, as opposed to interfaces, and it
does nothing much besides marking which struct device's go with an
overall USB device plus providing suspend/resume methods.  Now that
users can unbind drivers at will using the sysfs "unbind" attribute, we
need a rational way of dealing with USB devices that are no longer under
full control of the USB stack.  The patch handles this by unconfiguring
the device, thereby removing all the interfaces and their associated
drivers and children.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as555) modifies the already-awkward
usb_lock_device_for_reset routine in usbcore by adding a timeout.  The
whole point of the routine is that the caller wants to acquire some
semaphores in the wrong order; protecting against the possibility of
deadlock by timing out seems only prudent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix the port numbering confusion for the S3C24XX platform device
information as reported by Rudy <rudyboy168@gmail.com>

This patch ensurs that the the ports are numbered 0 and 1.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as554) makes the hub driver disconnect any child USB devices
when it is unbound from a hub.  Normally this will never happen, but
there are a few oddball ways to unbind the hub driver while leaving the
children intact.  For example, the new "unbind" sysfs attribute can be
used for this purpose.

Given that unbinding hubs with children is now safe, the patch also
removes the code that prevented people from doing so using usbfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as553) merely moves some code and deletes an unneeded test in
the hub driver.  This is in preparation for the patch that follows.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Adding flash-device support to the shuttle_usbat driver in 2.6.11
introduced the need to detect which type of device we are dealing with:
CDRW drive, or flash media reader.

The detection routine used turned out to not work for HP8200 CDRW users,
who saw their devices being detected as a flash disk.

This patch (which has been tested on both flash and cdrom) removes some
unnecessary code, moves device detection to much later during
initialization, and introduces a new detection routine which appears to
work.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

29 July 2005, Cambridge, MA:

This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel.  Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system.  For over a year it hasn't
been used for anything other than printing warning messages."

An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time.  As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches.  Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."

Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory.  "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to.  That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."

Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls.  His only comment was "Applied, thanks."
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch started life as as479b, and has been rediffed.  Please note
the order of submission of this latest patch series -- even tho this has
an older original number, it is the last patch I'll be sending today.

This patch changes the reported SCSI revision level to 2 for all
disk-type devices.  This is needed in a few cases because the device
reports a level of 3 or higher but then crashes when given a REPORT LUNS
command (for which support is supposed to be mandatory at those levels).
This shouldn't harm us, since it only matters for sparse LUNs and we
have separate ways of coping with that.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch is originally from Nick Sillik, and has been rediffed against
the latest tree.

This patch adds usability to the OneTouch Button on Maxtor External USB
Hard Drives. Using an unusual device entry it declares an extra init
function which claims the interrupt endpoint associated with this
button.  The button is connected to the input system.
Signed-off-by: Nick Sillik <n.sillik@temple.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch started life as as534, and has been re-diffed against the latest
tree.

usb-storage has a small loophole, a window between the time queuecommand
accepts a new command and the time the control thread starts to execute
it.  If disconnect is called during that window, the driver won't cancel
the pending command -- we've been relying on the SCSI core to cancel it
for us during host removal.  But it's better for usb-storage to cancel
it;  this avoids races and reduces reliance on the SCSI core.
Fortunately cancelling these commands is easy to do; the key is to do it
_before_ calling scsi_remove_host.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch started life as as533, and has been re-diffed against the
current tree.

Disconnect processing in usb-storage naturally divides into two parts:
one to quiesce the driver (make sure no commands are executing or
queued) and remove the host, and the other to deallocate all the USB and
non-USB resources.  This patch creates two subroutines to handle those
two parts.  Mostly it's just code movement, but there is one significant
change.  If the scsi-scanning thread fails to initialize but the host
has successfully been added, we need to quiesce the driver before
removing the host.  After all, it's possible that scanning could have
been initiated from somewhere else, such as userspace -- very low
probability, but it's easily handled by calling the new subroutine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch started life as as531 from Alan Stern.  It has been rediffed
against the latest tree.

The SCSI people have deprecated the use of scsi_cmnd.serial_number for
anything other than printk.  Worse than that, the SCSI core doesn't
always increment the number (when the error handler is running, for
example).  So this patch creates a locally-stored value for use in
bulk-only tags.  The net result is a simplification, since we no longer
have to save & restore the serial_number value while autosensing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Switch isp116x-hcd over from root hub polling to interrupt.  This change closes
also a race that was present with the old polling scheme: status polling could
happen in a time window, where root hub status bits were not stable.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch removes support for user-provided platform-specific hardware reset
and clock starting/stopping functions. Hardware reset was needed earlier as
getting the software reset working was tricky due to the lack of documentation.
Recently, a number of people using isp116x have said the software reset is
working for them.

I haven't heard of anybody using the clock starting/stopping.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch sets the isp116x to report overcurrent always per-port.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The isp116x chip will now always be in per-port power switching mode. Remove
conf options to set any other mode.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch removes the power-on-to-power-good-time configuration option for
isp116x-hcd.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This just fixes some gfp flags warnings that joined us recently.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Rate-limit usblp printer error status messages.

I unplugged my USB printer and almost instantly got several hundred
of these in my kernel message log:
drivers/usb/class/usblp.c: usblp0: error -19 reading printer status
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Back out Axboe-style quasi-S/G and replace it with one command and
repeated URBs. This is similar to what usb-storage does, only instead
of a few URBs allocated together, one URB is reused.

Jens's idea was very nice, but it collapsed when I had to support
packet commads for CD burning. I cannot issue two or more packet
commands where application expected only one.

However, burning does not work completely yet. The cdrecord starts,
recognizes the device, then aborts without writing a TOC.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When Al Viro saw the ub.c, he observed that it was a proof positive of
Linus not reading patches anymore: names like fo_ob_ar_ba_2 used to
cause serious fireworks. In my defence, any good scheme can be pushed
to the realm of absurd if pushed far enough.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Evidently, Yani Ioannou's display is wider than mine.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This the quasi-S/G patch for ub as suggested by Jens Axboe at OLS and
implemented that night before 4 a.m. Surprisingly, it worked right away...
Alas, I had to skip some OLS partying, but it was for the good cause.
Now the speed of ub is quite acceptable even on partitions with small
block size.

The ub does not really support S/G. Instead, it just tells the block
layer that it does. Then, most of the time, the block layer merges
requests and passes single-segmnent requests down to ub; everything
works as before. Very rarely ub gets an unmerged S/G request. In such
case, it issues several commands to the device.

I added a small array of counters to monitor the merging (sg_stat).
This may be dropped later.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds an entry in the unusual_devs.h file for a Mitsumi card
reader/floppy combo that uses a VIA chipset. The IGNORE_RESIDUE flag was
needed for the second LUN to operate properly.
Signed-off-by: Mihnea-Costin Grigore <mihnea@zulu.ro>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as551) fixes another little problem recently added to the
USB core.  Someone didn't fix the type of the first argument to
unregister_chrdev_region.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch introduces a /sys/class/usb_device/ class
where every connected usb-device will show up:

  tree /sys/class/usb_device/
  /sys/class/usb_device/
  |-- usb1.1
  |   |-- dev
  |   `-- device -> ../../../devices/pci0000:00/0000:00:1d.0/usb1
  |-- usb2.1
  |   |-- dev
  |   `-- device -> ../../../devices/pci0000:00/0000:00:1d.1/usb2
  ...

The presence of the "dev" file lets udev create real device nodes.
  kay@pim:~/src/linux-2.6> tree /dev/bus/usb/
  /dev/bus/usb/
  |-- 1
  |   `-- 1
  |-- 2
  |   `-- 1
  ...

udev rule:
  SUBSYSTEM="usb_device", PROGRAM="/sbin/usb_device %k", NAME="%c"
  (echo $1 | /bin/sed 's/usb\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/')

This makes libusb pick up the real nodes instead of the mounted usbfs:
  export USB_DEVFS_PATH=/dev/bus/usb

Background:
  All this makes it possible to manage usb devices with udev instead of
  the devfs solution. We are currently working on a pam_console/resmgr
  replacement driven by udev and a pam-helper. It applies ACL's to device
  nodes, which is required for modern desktop functionalty like
  "Fast User Switching" or multiple local login support.

New patch with its own major. I've succesfully disabled usbfs and use real
nodes only on my box. With: "export USB_DEVFS_PATH=/dev/bus/usb" libusb picks
up the udev managed nodes instead of reading usbfs files.

This makes udev to provide symlinks for libusb to pick up:
  SUBSYSTEM="usb_device", PROGRAM="/sbin/usbdevice %k", SYMLINK="%c"

/sbin/usbdevice:
  #!/bin/sh
  echo $1 | /bin/sed 's/usbdev\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/'
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

To recap: My new G4 powerbook has a bluetooth device that boots up in
what apppears to be a compatability mode - it looks exactly like an HID
keyboard/mouse device.

A special command sequence is sent to switch it into full bluetooth
mode. When this occurs the original HID device vanishes, and a new
(bluetooth HID) USB device appears on the bus with a different product
ID.

The original thread is here:
http://sourceforge.net/mailarchive/message.php?msg_id=12532263

The attached patch adds the device to the hid-core quirks so that
hid-core ignores it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch for the ftdi_sio driver adds a bunch of new devices and fixes
an incorrect PID:

o Fix PID for ELV UO100 (the PID was in fact for ELV UR100).
o Add PID ELV UR100 (see above) and ELV ALC 8500 Expert.
o Add a whole bunch of other PIDs for ELV USB devices, commented out for
   now as they may be used by other drivers eventually.  (Christian Abt
   of ELV.de submitted a full list of devices including an indication of
   which set of drivers are used by default in the MS Windows world.  We
   decided to comment out the devices that use FTDI's D2XX Windows
   drivers by default.)
o Add PIDs for eight devices from Xsens Technologies BV (submitted in a
   patch against 2.6.12.2 by Patrick Riphagen).
o Add PID for Falcom Samba GPRS modem (submitted by Sebastian Schubert).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ftdi_sio: Support one user specified vendor and product ID via a couple
of new module parameters.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This trivial patch makes pl2303 driver work correctly with pl2303HX chip.
Apparently some bug in HX version of pl2303 makes the chip loose some
transmitted bytes or stop working at all after reception of
USB_REQ_CLEAR_FEATURE mesage. Logs generated by UsbSnoop application reveal
that windows driver does not send this type of messages to the converter.

From: "Dariusz M." <D.Marcinkiewicz@elka.pw.edu.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch centralizes the assignment of bcdDevice numbers for different
gadget controllers.  This won't improve the object code at all, but it
does save a lot of repetitive and error-prone source code ... and will
simplify the work of supporting a new controller driver, since most new
gadget drivers will no longer need patches (unless some hardware quirks
limit USB protocol messaging).

Added minor cleanups and identifer hooks for the UDC in the Freescale
iMX series processors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The following patch removes unneeded casts for the following (void *) pointers:
	- tty_struct->driver_data
	- void *private argument of usb_serial_port_softint()
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Reading this driver I noticed some trailing whitespaces and tabs so I
removed them with some 80th column fitting and a few more similar
things.

From: Carlo Perassi <carlo@linux.it>
Signed-off-by: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Carlo Perassi <carlo@linux.it>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Proud member of Uglyhacks'R'US.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>