GCC complains that "ret" is uninitialized here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some Arizona chips have a higher frequency for the FLL VCO, support this
in the common code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds input selection of main codec clock - from what pin.
Both registers set same value since codec uses clock divider or pll at one time.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds AGC target level and times settings for TLV320AIC3x.
Enums uses small arrays of two channels left and right since it uses different registers.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds missing deemphasis switch.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The analogue PGA shifts were used; this makes no practical difference as
the values are the same.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some devices have four input structures rather than three.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Since we're now relying on DAPM for things like enabling clocks when we
reparent the clocks for widgets we need to either use conditional routes
(which are expensive) or remove routes at runtime. Add a route removal
API to support this use case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

If we add a new route at runtime then we'll need to recheck the connections
to the affected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Some userspace will open a PCM device and then configure mixers
for routing before triggering. This patch allows userspace to do
this sequence.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix spelling mistake in "High-Performance" option of twl6040 power mode.
Signed-off-by: Simon Wilson <simonwilson@google.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use dev_ style logging throughout soc_new_pcm()
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Not previously noticed due to normal usage being with CODEC<->CODEC links.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This enables common telephony use cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If an audio interface is configured to use ASYNCCLK then update the
asynchronous sample rate rather than one of our primary sample rates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

mx27pdk board also has a mc13783 codec.

Add support for it and do a run-time machine type check to perform the correct
audiomux settings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If we don't set IMX_AUDMUX_V2_PTCR_TCLKDIR in the AUDMUX PTCR
register (means Tx clock pin is input), we don't need to set
IMX_AUDMUX_V2_PTCR_TCSEL as well. Since both i.MX35, i.MX51 and
i.MX6 datasheet says "When Tx clock pin set as an input, the TCSEL
settings are ignored".
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Allow any BCLK which can be divided down to generate LRCLK, not just the
lowest possible BCLK to clock out the samples.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Allow the user to select which of the system clocks each AIF is referenced
to and constran the DAI to the set of frequencies which can be generated
from that clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

They're the rates for the BCLK, not for the sample rate, so rename so that
we don't confuse ourselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch implements the spdif out driver for ST peripheral. This
peripheral implements IEC60958 standard
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adds missing register default values to cache.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adds register and bit shift definitions in header file.
Changes are for TLV320AIC310x based on data sheet.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Leave it up to the machine driver to disable accessory detection if
desired, the common pattern is to have accessory detection be a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since most new drivers are expected to use regmap and since frequently the
only thing we need to do in the CODEC probe function is configure the I/O
try to initialise the register I/O using regmap if the driver hasn't done
so after probe().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI fifo and memory in
place of legacy Tegra APB DMA.

Because generic soc-dmaengine-pcm uses the DMAs API
based on dmaengine, using the exported APIs provided
by this generic driver.

The new driver is selected if legacy driver is not
selected and new dma driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Stereo is not yet supported by dapm widgets, so remove stereo code from
snd_soc_dapm_get_volsw(), and warn if stereo controls are detected.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

snd_soc_dapm_put_volsw() sets connect incorrectly in the case max > 1 with
invert. In that case, the raw disconnect value should be max, which corresponds
to the userspace value 0.

This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise we fail to link when building as modules due to multiple
init/exit functions.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds the support for spdif in audio codec.
Signed-off-by: vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise sparse gets very upset with us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The patches for stubbing out the generic clock API still haven't been
applied so we need to either add ifdefs here or add a dependency until
someone decides to actually apply them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This gets the registers set up as early as possible, mainly useful for the
GPIOs to ensure that they're in the correct mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>