- 20 Dec, 2017 36 commits
-
-
Doug Berger authored
[ Upstream commit 07c52d6a ] Add a spinlock to ensure that irq0_stat is not unintentionally altered as the result of preemption. Also removed unserviced irq0 interrupts and removed irq1_stat since there is no bottom half service for those interrupts. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Doug Berger <opendmb@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Doug Berger authored
[ Upstream commit 7627409c ] Since the internal PHY is powered up during the open and resume functions it should be powered back down if the functions fail. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Doug Berger authored
[ Upstream commit eca4bad7 ] The reserved gphy_rev value of 0x01ff must be tested before the old or new scheme for GPHY major versioning are tested, otherwise it will be treated as 0xff00 according to the old scheme. Fixes: b04a2f5b ("net: bcmgenet: add support for new GENET PHY revision scheme") Signed-off-by:
-
Doug Berger authored
[ Upstream commit 1ad3d225 ] The gap between the Tx status counters and the Rx RUNT counters is now being added to allow correct reporting of the registers. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Doug Berger authored
[ Upstream commit ffff7132 ] The location of the RBUF overflow and error counters has moved between different version of the GENET MAC. This commit corrects the driver to read from the correct locations depending on the version of the GENET MAC. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Michael Chan authored
[ Upstream commit 520ad89a ] In some situations, the firmware will return 0 for autoneg supported speed. This may happen if the firmware detects no SFP module, for example. The driver should ignore this so that we don't end up with an invalid autoneg setting with nothing advertised. When SFP module is inserted, we'll get the updated settings from firmware at that time. Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Alexander Potapenko authored
[ Upstream commit 9f138fa6 ] KMSAN reports a use of uninitialized memory in put_cmsg() because msg.msg_flags in recvfrom haven't been initialized properly. The flag values don't affect the result on this path, but it's still a good idea to initialize them explicitly. Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
Andrea Arcangeli authored
[ Upstream commit 46aa6a30 ] linux/tools/testing/selftests/vm $ make gcc -Wall -I ../../../../usr/include compaction_test.c -lrt -o /compaction_test /usr/lib/gcc/x86_64-pc-linux-gnu/4.9.4/../../../../x86_64-pc-linux-gnu/bin/ld: cannot open output file /compaction_test: Permission denied collect2: error: ld returned 1 exit status make: *** [../lib.mk:54: /compaction_test] Error 1 Since commit a8ba798b ("selftests: enable O and KBUILD_OUTPUT") selftests/vm build fails if run from the "selftests/vm" directory, but it works in the selftests/ directory. It's quicker to be able to do a local vm-only build after a tree wipe and this patch allows for it again. Link: http://lkml.kernel.org/r/20170302173738.18994-4-aarcange@redhat.comSigned-off-by:
Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Andrea Arcangeli authored
[ Upstream commit 6bbc4a41 ] __do_fault assumes vmf->page has been initialized and is valid if VM_FAULT_NOPAGE is not returned by vma->vm_ops->fault(vma, vmf). handle_userfault() in turn should return VM_FAULT_NOPAGE if it doesn't return VM_FAULT_SIGBUS or VM_FAULT_RETRY (the other two possibilities). This VM_FAULT_NOPAGE case is only invoked when signal are pending and it didn't matter for anonymous memory before. It only started to matter since shmem was introduced. hugetlbfs also takes a different path and doesn't exercise __do_fault. Link: http://lkml.kernel.org/r/20170228154201.GH5816@redhat.comSigned-off-by:
Dmitry Vyukov <dvyukov@google.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Signed-off-by:
-
Guoqing Jiang authored
[ Upstream commit 9c8043f3 ] To avoid memory leak, we need to free the cinfo which is allocated when node join cluster. Reviewed-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Guoqing Jiang <gqjiang@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Chunfeng Yun authored
[ Upstream commit 94a631d9 ] hcc_params is set in xhci_gen_setup() called from usb_add_hcd(), so checks the Maximum Primary Stream Array Size in the hcc_params register after adding primary hcd. Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Radim Krčmář authored
[ Upstream commit 05d8d346 ] Before trying to do nested_get_page() in nested_vmx_merge_msr_bitmap(), we have already checked that the MSR bitmap address is valid (4k aligned and within physical limits). SDM doesn't specify what happens if the there is no memory mapped at the valid address, but Intel CPUs treat the situation as if the bitmap was configured to trap all MSRs. KVM already does that by returning false and a correct handling doesn't need the guest-trigerrable warning that was reported by syzkaller: (The warning was originally there to catch some possible bugs in nVMX.) ------------[ cut here ]------------ WARNING: CPU: 0 PID: 7832 at arch/x86/kvm/vmx.c:9709 nested_vmx_merge_msr_bitmap arch/x86/kvm/vmx.c:9709 [inline] WARNING: CPU: 0 PID: 7832 at arch/x86/kvm/vmx.c:9709 nested_get_vmcs12_pages+0xfb6/0x15c0 arch/x86/kvm/vmx.c:9640 Kernel panic - not syncing: panic_on_warn set ... CPU: 0 PID: 7832 Comm: syz-executor1 Not tainted 4.10.0+ #229 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:15 [inline] dump_stack+0x2ee/0x3ef lib/dump_stack.c:51 panic+0x1fb/0x412 kernel/panic.c:179 __warn+0x1c4/0x1e0 kernel/panic.c:540 warn_slowpath_null+0x2c/0x40 kernel/panic.c:583 nested_vmx_merge_msr_bitmap arch/x86/kvm/vmx.c:9709 [inline] nested_get_vmcs12_pages+0xfb6/0x15c0 arch/x86/kvm/vmx.c:9640 enter_vmx_non_root_mode arch/x86/kvm/vmx.c:10471 [inline] nested_vmx_run+0x6186/0xaab0 arch/x86/kvm/vmx.c:10561 handle_vmlaunch+0x1a/0x20 arch/x86/kvm/vmx.c:7312 vmx_handle_exit+0xfc0/0x3f00 arch/x86/kvm/vmx.c:8526 vcpu_enter_guest arch/x86/kvm/x86.c:6982 [inline] vcpu_run arch/x86/kvm/x86.c:7044 [inline] kvm_arch_vcpu_ioctl_run+0x1418/0x4840 arch/x86/kvm/x86.c:7205 kvm_vcpu_ioctl+0x673/0x1120 arch/x86/kvm/../../../virt/kvm/kvm_main.c:2570 Reported-by:
Jim Mattson <jmattson@google.com> [Jim Mattson explained the bare metal behavior: "I believe this behavior would be documented in the chipset data sheet rather than the SDM, since the chipset returns all 1s for an unclaimed read."] Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Javier Martinez Canillas authored
[ Upstream commit fd567653 ] The driver doesn't have a struct of_device_id table but supported devices are registered via Device Trees. This is working on the assumption that a I2C device registered via OF will always match a legacy I2C device ID and that the MODALIAS reported will always be of the form i2c:<device>. But this could change in the future so the correct approach is to have an OF device ID table if the devices are registered via OF. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
-
Ilan peer authored
commit 57629915 upstream. The code was setting the capabilities byte to zero, after it was already properly set previously. Fix it. The bug was found while debugging hwsim mesh tests failures that happened since the commit mentioned below. Fixes: 76f43b4c ("mac80211: Remove invalid flag operations in mesh TSF synchronization") Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Reviewed-by:
Masashi Honma <masashi.honma@gmail.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Cc: Richard Schütz <rschuetz@uni-koblenz.de> Cc: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de> Signed-off-by:
-
Chandan Rajendra authored
commit 9d5afec6 upstream. On a ppc64 machine, when mounting a fuzzed ext2 image (generated by fsfuzzer) the following call trace is seen, VFS: brelse: Trying to free free buffer WARNING: CPU: 1 PID: 6913 at /root/repos/linux/fs/buffer.c:1165 .__brelse.part.6+0x24/0x40 .__brelse.part.6+0x20/0x40 (unreliable) .ext4_find_entry+0x384/0x4f0 .ext4_lookup+0x84/0x250 .lookup_slow+0xdc/0x230 .walk_component+0x268/0x400 .path_lookupat+0xec/0x2d0 .filename_lookup+0x9c/0x1d0 .vfs_statx+0x98/0x140 .SyS_newfstatat+0x48/0x80 system_call+0x58/0x6c This happens because the directory that ext4_find_entry() looks up has inode->i_size that is less than the block size of the filesystem. This causes 'nblocks' to have a value of zero. ext4_bread_batch() ends up not reading any of the directory file's blocks. This renders the entries in bh_use[] array to continue to have garbage data. buffer_uptodate() on bh_use[0] can then return a zero value upon which brelse() function is invoked. This commit fixes the bug by returning -ENOENT when the directory file has no associated blocks. Reported-by:
Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by:
Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by:
-
Eryu Guan authored
commit c894aa97 upstream. Currently, fallocate(2) with KEEP_SIZE followed by a fdatasync(2) then crash, we'll see wrong allocated block number (stat -c %b), the blocks allocated beyond EOF are all lost. fstests generic/468 exposes this bug. Commit 67a7d5f5 ("ext4: fix fdatasync(2) after extent manipulation operations") fixed all the other extent manipulation operation paths such as hole punch, zero range, collapse range etc., but forgot the fallocate case. So similarly, fix it by recording the correct journal tid in ext4 inode in fallocate(2) path, so that ext4_sync_file() will wait for the right tid to be committed on fdatasync(2). This addresses the test failure in xfstests test generic/468. Signed-off-by:
Eryu Guan <eguan@redhat.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Adam Wallis authored
commit 6f6a23a2 upstream. Commit adfa543e ("dmatest: don't use set_freezable_with_signal()") introduced a bug (that is in fact documented by the patch commit text) that leaves behind a dangling pointer. Since the done_wait structure is allocated on the stack, future invocations to the DMATEST can produce undesirable results (e.g., corrupted spinlocks). Commit a9df21e3 ("dmaengine: dmatest: warn user when dma test times out") attempted to WARN the user that the stack was likely corrupted but did not fix the actual issue. This patch fixes the issue by pushing the wait queue and callback structs into the the thread structure. If a failure occurs due to time, dmaengine_terminate_all will force the callback to safely call wake_up_all() without possibility of using a freed pointer. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=197605 Fixes: adfa543e ("dmatest: don't use set_freezable_with_signal()") Reviewed-by:
Sinan Kaya <okaya@codeaurora.org> Suggested-by:
Shunyong Yang <shunyong.yang@hxt-semitech.com> Signed-off-by:
Adam Wallis <awallis@codeaurora.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
David Lechner authored
commit 7f6d2ecd upstream. Trying to read the MAC address from an eeprom that has an offset that is not a multiple of 4 causes an error currently. Fix it by changing the nvmem stride to 1. Signed-off-by:
David Lechner <david@lechnology.com> [Bartosz: tweaked the commit message] Signed-off-by:
Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by:
-
Steven Rostedt authored
commit f73c52a5 upstream. Daniel Wagner reported a crash on the BeagleBone Black SoC. This is a single CPU architecture, and does not have a functional arch_send_call_function_single_ipi() implementation which can crash the kernel if that is called. As it only has one CPU, it shouldn't be called, but if the kernel is compiled for SMP, the push/pull RT scheduling logic now calls it for irq_work if the one CPU is overloaded, it can use that function to call itself and crash the kernel. Ideally, we should disable the SCHED_FEAT(RT_PUSH_IPI) if the system only has a single CPU. But SCHED_FEAT is a constant if sched debugging is turned off. Another fix can also be used, and this should also help with normal SMP machines. That is, do not initiate the pull code if there's only one RT overloaded CPU, and that CPU happens to be the current CPU that is scheduling in a lower priority task. Even on a system with many CPUs, if there's many RT tasks waiting to run on a single CPU, and that CPU schedules in another RT task of lower priority, it will initiate the PULL logic in case there's a higher priority RT task on another CPU that is waiting to run. But if there is no other CPU with waiting RT tasks, it will initiate the RT pull logic on itself (as it still has RT tasks waiting to run). This is a wasted effort. Not only does this help with SMP code where the current CPU is the only one with RT overloaded tasks, it should also solve the issue that Daniel encountered, because it will prevent the PULL logic from executing, as there's only one CPU on the system, and the check added here will cause it to exit the RT pull code. Reported-by:
Daniel Wagner <wagi@monom.org> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by:
Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-rt-users <linux-rt-users@vger.kernel.org> Fixes: 4bdced5c ("sched/rt: Simplify the IPI based RT balancing logic") Link: http://lkml.kernel.org/r/20171202130454.4cbbfe8d@vmware.local.homeSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Scott Mayhew authored
commit dc4fd9ab upstream. If there were no commit requests, then nfs_commit_inode() should not wait on the commit or mark the inode dirty, otherwise the following BUG_ON can be triggered: [ 1917.130762] kernel BUG at fs/inode.c:578! [ 1917.130766] Oops: Exception in kernel mode, sig: 5 [#1] [ 1917.130768] SMP NR_CPUS=2048 NUMA pSeries [ 1917.130772] Modules linked in: iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi blocklayoutdriver rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache sunrpc sg nx_crypto pseries_rng ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic crct10dif_common ibmvscsi scsi_transport_srp ibmveth scsi_tgt dm_mirror dm_region_hash dm_log dm_mod [ 1917.130805] CPU: 2 PID: 14923 Comm: umount.nfs4 Tainted: G ------------ T 3.10.0-768.el7.ppc64 #1 [ 1917.130810] task: c0000005ecd88040 ti: c00000004cea0000 task.ti: c00000004cea0000 [ 1917.130813] NIP: c000000000354178 LR: c000000000354160 CTR: c00000000012db80 [ 1917.130816] REGS: c00000004cea3720 TRAP: 0700 Tainted: G ------------ T (3.10.0-768.el7.ppc64) [ 1917.130820] MSR: 8000000100029032 <SF,EE,ME,IR,DR,RI> CR: 22002822 XER: 20000000 [ 1917.130828] CFAR: c00000000011f594 SOFTE: 1 GPR00: c000000000354160 c00000004cea39a0 c0000000014c4700 c0000000018cc750 GPR04: 000000000000c750 80c0000000000000 0600000000000000 04eeb76bea749a03 GPR08: 0000000000000034 c0000000018cc758 0000000000000001 d000000005e619e8 GPR12: c00000000012db80 c000000007b31200 0000000000000000 0000000000000000 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR24: 0000000000000000 c000000000dfc3ec 0000000000000000 c0000005eefc02c0 GPR28: d0000000079dbd50 c0000005b94a02c0 c0000005b94a0250 c0000005b94a01c8 [ 1917.130867] NIP [c000000000354178] .evict+0x1c8/0x350 [ 1917.130871] LR [c000000000354160] .evict+0x1b0/0x350 [ 1917.130873] Call Trace: [ 1917.130876] [c00000004cea39a0] [c000000000354160] .evict+0x1b0/0x350 (unreliable) [ 1917.130880] [c00000004cea3a30] [c0000000003558cc] .evict_inodes+0x13c/0x270 [ 1917.130884] [c00000004cea3af0] [c000000000327d20] .kill_anon_super+0x70/0x1e0 [ 1917.130896] [c00000004cea3b80] [d000000005e43e30] .nfs_kill_super+0x20/0x60 [nfs] [ 1917.130900] [c00000004cea3c00] [c000000000328a20] .deactivate_locked_super+0xa0/0x1b0 [ 1917.130903] [c00000004cea3c80] [c00000000035ba54] .cleanup_mnt+0xd4/0x180 [ 1917.130907] [c00000004cea3d10] [c000000000119034] .task_work_run+0x114/0x150 [ 1917.130912] [c00000004cea3db0] [c00000000001ba6c] .do_notify_resume+0xcc/0x100 [ 1917.130916] [c00000004cea3e30] [c00000000000a7b0] .ret_from_except_lite+0x5c/0x60 [ 1917.130919] Instruction dump: [ 1917.130921] 7fc3f378 486734b5 60000000 387f00a0 38800003 4bdcb365 60000000 e95f00a0 [ 1917.130927] 694a0060 7d4a0074 794ad182 694a0001 <0b0a0000> 892d02a4 2f890000 40de0134 Signed-off-by:
Scott Mayhew <smayhew@redhat.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Mathias Nyman authored
commit 5d9b70f7 upstream. Avoid null pointer dereference if some function is walking through the devs array accessing members of a new virt_dev that is mid allocation. Add the virt_dev to xhci->devs[i] _after_ the virt_device and all its members are properly allocated. issue found by KASAN: null-ptr-deref in xhci_find_slot_id_by_port "Quick analysis suggests that xhci_alloc_virt_device() is not mutex protected. If so, there is a time frame where xhci->devs[slot_id] is set but not fully initialized. Specifically, xhci->devs[i]->udev can be NULL." Signed-off-by:
-
Sukumar Ghorai authored
commit a0085f25 upstream. BT-Controller connected as platform non-root-hub device and usb-driver initialize such device with wakeup disabled, Ref. usb_new_device(). At present wakeup-capability get enabled by hid-input device from usb function driver(e.g. BT HID device) at runtime. Again some functional driver does not set usb-wakeup capability(e.g LE HID device implement as HID-over-GATT), and can't wakeup the host on USB. Most of the device operation (such as mass storage) initiated from host (except HID) and USB wakeup aligned with host resume procedure. For BT device, usb-wakeup capability need to enable form btusc driver as a generic solution for multiple profile use case and required for USB remote wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature need to enable/disable with HCI interface up and down. Signed-off-by:
Sukumar Ghorai <sukumar.ghorai@intel.com> Signed-off-by:
Amit K Bag <amit.k.bag@intel.com> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
-
Chunfeng Yun authored
commit 72b663a9 upstream. For MTK's xHCI 1.0 or latter, TD size is the number of max packet sized packets remaining in the TD, not including this TRB (following spec). For MTK's xHCI 0.96 and older, TD size is the number of max packet sized packets remaining in the TD, including this TRB (not following spec). Signed-off-by:
-
Yan, Zheng authored
commit 040d7860 upstream. Negative child dentry holds reference on inode's alias, it makes d_prune_aliases() do nothing. Signed-off-by:
"Yan, Zheng" <zyan@redhat.com> Reviewed-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Shuah Khan authored
commit be6123df upstream. stub_send_ret_submit() handles urb with a potential null transfer_buffer, when it replays a packet with potential malicious data that could contain a null buffer. Add a check for the condition when actual_length > 0 and transfer_buffer is null. Reported-by:
Secunia Research <vuln@secunia.com> Signed-off-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Shuah Khan authored
commit c6688ef9 upstream. Harden CMD_SUBMIT path to handle malicious input that could trigger large memory allocations. Add checks to validate transfer_buffer_length and number_of_packets to protect against bad input requesting for unbounded memory allocations. Validate early in get_pipe() and return failure. Reported-by:
-
Felipe Balbi authored
commit 541b6fe6 upstream. According to USB Specification 2.0 table 9-4, wMaxPacketSize is a bitfield. Endpoint's maxpacket is laid out in bits 10:0. For high-speed, high-bandwidth isochronous endpoints, bits 12:11 contain a multiplier to tell us how many transactions we want to try per uframe. This means that if we want an isochronous endpoint to issue 3 transfers of 1024 bytes per uframe, wMaxPacketSize should contain the value: 1024 | (2 << 11) or 5120 (0x1400). In order to make Host and Peripheral controller drivers' life easier, we're adding a helper which returns bits 12:11. Note that no care is made WRT to checking endpoint type and gadget's speed. That's left for drivers to handle. Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Shuah Khan authored
commit 635f545a upstream. get_pipe() routine doesn't validate the input endpoint number and uses to reference ep_in and ep_out arrays. Invalid endpoint number can trigger BUG(). Range check the epnum and returning error instead of calling BUG(). Change caller stub_recv_cmd_submit() to handle the get_pipe() error return. Reported-by:
-
Alan Stern authored
commit 48a4ff1c upstream. A malicious USB device with crafted descriptors can cause the kernel to access unallocated memory by setting the bNumInterfaces value too high in a configuration descriptor. Although the value is adjusted during parsing, this adjustment is skipped in one of the error return paths. This patch prevents the problem by setting bNumInterfaces to 0 initially. The existing code already sets it to the proper value after parsing is complete. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
-
David Kozub authored
commit 62354454 upstream. There is another JMS567-based USB3 UAS enclosure (152d:0578) that fails with the following error: [sda] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [sda] tag#0 Sense Key : Illegal Request [current] [sda] tag#0 Add. Sense: Invalid field in cdb The issue occurs both with UAS (occasionally) and mass storage (immediately after mounting a FS on a disk in the enclosure). Enabling US_FL_BROKEN_FUA quirk solves this issue. This patch adds an UNUSUAL_DEV with US_FL_BROKEN_FUA for the enclosure for both UAS and mass storage. Signed-off-by:
David Kozub <zub@linux.fjfi.cvut.cz> Acked-by:
-
Changbin Du authored
commit 90e406f9 upstream. The default NR_CPUS can be very large, but actual possible nr_cpu_ids usually is very small. For my x86 distribution, the NR_CPUS is 8192 and nr_cpu_ids is 4. About 2 pages are wasted. Most machines don't have so many CPUs, so define a array with NR_CPUS just wastes memory. So let's allocate the buffer dynamically when need. With this change, the mutext tracing_cpumask_update_lock also can be removed now, which was used to protect mask_str. Link: http://lkml.kernel.org/r/1512013183-19107-1-git-send-email-changbin.du@intel.com Fixes: 36dfe925 ("ftrace: make use of tracing_cpumask") Signed-off-by:
Changbin Du <changbin.du@intel.com> Signed-off-by:
-
NeilBrown authored
commit 302ec300 upstream. Commit ecc0c469 ("autofs: don't fail mount for transient error") was meant to replace an 'if' with a 'switch', but instead added the 'switch' leaving the case in place. Link: http://lkml.kernel.org/r/87zi6wstmw.fsf@notabene.neil.brown.name Fixes: ecc0c469 ("autofs: don't fail mount for transient error") Reported-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Eric Biggers authored
commit ecaaab56 upstream. When asked to encrypt or decrypt 0 bytes, both the generic and x86 implementations of Salsa20 crash in blkcipher_walk_done(), either when doing 'kfree(walk->buffer)' or 'free_page((unsigned long)walk->page)', because walk->buffer and walk->page have not been initialized. The bug is that Salsa20 is calling blkcipher_walk_done() even when nothing is in 'walk.nbytes'. But blkcipher_walk_done() is only meant to be called when a nonzero number of bytes have been provided. The broken code is part of an optimization that tries to make only one call to salsa20_encrypt_bytes() to process inputs that are not evenly divisible by 64 bytes. To fix the bug, just remove this "optimization" and use the blkcipher_walk API the same way all the other users do. Reproducer: #include <linux/if_alg.h> #include <sys/socket.h> #include <unistd.h> int main() { int algfd, reqfd; struct sockaddr_alg addr = { .salg_type = "skcipher", .salg_name = "salsa20", }; char key[16] = { 0 }; algfd = socket(AF_ALG, SOCK_SEQPACKET, 0); bind(algfd, (void *)&addr, sizeof(addr)); reqfd = accept(algfd, 0, 0); setsockopt(algfd, SOL_ALG, ALG_SET_KEY, key, sizeof(key)); read(reqfd, key, sizeof(key)); } Reported-by:
syzbot <syzkaller@googlegroups.com> Fixes: eb6f13eb ("[CRYPTO] salsa20_generic: Fix multi-page processing") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Eric Biggers authored
commit af3ff804 upstream. Because the HMAC template didn't check that its underlying hash algorithm is unkeyed, trying to use "hmac(hmac(sha3-512-generic))" through AF_ALG or through KEYCTL_DH_COMPUTE resulted in the inner HMAC being used without having been keyed, resulting in sha3_update() being called without sha3_init(), causing a stack buffer overflow. This is a very old bug, but it seems to have only started causing real problems when SHA-3 support was added (requires CONFIG_CRYPTO_SHA3) because the innermost hash's state is ->import()ed from a zeroed buffer, and it just so happens that other hash algorithms are fine with that, but SHA-3 is not. However, there could be arch or hardware-dependent hash algorithms also affected; I couldn't test everything. Fix the bug by introducing a function crypto_shash_alg_has_setkey() which tests whether a shash algorithm is keyed. Then update the HMAC template to require that its underlying hash algorithm is unkeyed. Here is a reproducer: #include <linux/if_alg.h> #include <sys/socket.h> int main() { int algfd; struct sockaddr_alg addr = { .salg_type = "hash", .salg_name = "hmac(hmac(sha3-512-generic))", }; char key[4096] = { 0 }; algfd = socket(AF_ALG, SOCK_SEQPACKET, 0); bind(algfd, (const struct sockaddr *)&addr, sizeof(addr)); setsockopt(algfd, SOL_ALG, ALG_SET_KEY, key, sizeof(key)); } Here was the KASAN report from syzbot: BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:341 [inline] BUG: KASAN: stack-out-of-bounds in sha3_update+0xdf/0x2e0 crypto/sha3_generic.c:161 Write of size 4096 at addr ffff8801cca07c40 by task syzkaller076574/3044 CPU: 1 PID: 3044 Comm: syzkaller076574 Not tainted 4.14.0-mm1+ #25 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x194/0x257 lib/dump_stack.c:53 print_address_description+0x73/0x250 mm/kasan/report.c:252 kasan_report_error mm/kasan/report.c:351 [inline] kasan_report+0x25b/0x340 mm/kasan/report.c:409 check_memory_region_inline mm/kasan/kasan.c:260 [inline] check_memory_region+0x137/0x190 mm/kasan/kasan.c:267 memcpy+0x37/0x50 mm/kasan/kasan.c:303 memcpy include/linux/string.h:341 [inline] sha3_update+0xdf/0x2e0 crypto/sha3_generic.c:161 crypto_shash_update+0xcb/0x220 crypto/shash.c:109 shash_finup_unaligned+0x2a/0x60 crypto/shash.c:151 crypto_shash_finup+0xc4/0x120 crypto/shash.c:165 hmac_finup+0x182/0x330 crypto/hmac.c:152 crypto_shash_finup+0xc4/0x120 crypto/shash.c:165 shash_digest_unaligned+0x9e/0xd0 crypto/shash.c:172 crypto_shash_digest+0xc4/0x120 crypto/shash.c:186 hmac_setkey+0x36a/0x690 crypto/hmac.c:66 crypto_shash_setkey+0xad/0x190 crypto/shash.c:64 shash_async_setkey+0x47/0x60 crypto/shash.c:207 crypto_ahash_setkey+0xaf/0x180 crypto/ahash.c:200 hash_setkey+0x40/0x90 crypto/algif_hash.c:446 alg_setkey crypto/af_alg.c:221 [inline] alg_setsockopt+0x2a1/0x350 crypto/af_alg.c:254 SYSC_setsockopt net/socket.c:1851 [inline] SyS_setsockopt+0x189/0x360 net/socket.c:1830 entry_SYSCALL_64_fastpath+0x1f/0x96 Reported-by:
-
Eric Biggers authored
commit d2890c37 upstream. In rsa_get_n(), if the buffer contained all 0's and "FIPS mode" is enabled, we would read one byte past the end of the buffer while scanning the leading zeroes. Fix it by checking 'n_sz' before '!*ptr'. This bug was reachable by adding a specially crafted key of type "asymmetric" (requires CONFIG_RSA and CONFIG_X509_CERTIFICATE_PARSER). KASAN report: BUG: KASAN: slab-out-of-bounds in rsa_get_n+0x19e/0x1d0 crypto/rsa_helper.c:33 Read of size 1 at addr ffff88003501a708 by task keyctl/196 CPU: 1 PID: 196 Comm: keyctl Not tainted 4.14.0-09238-g1d3b78bb #26 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014 Call Trace: rsa_get_n+0x19e/0x1d0 crypto/rsa_helper.c:33 asn1_ber_decoder+0x82a/0x1fd0 lib/asn1_decoder.c:328 rsa_set_pub_key+0xd3/0x320 crypto/rsa.c:278 crypto_akcipher_set_pub_key ./include/crypto/akcipher.h:364 [inline] pkcs1pad_set_pub_key+0xae/0x200 crypto/rsa-pkcs1pad.c:117 crypto_akcipher_set_pub_key ./include/crypto/akcipher.h:364 [inline] public_key_verify_signature+0x270/0x9d0 crypto/asymmetric_keys/public_key.c:106 x509_check_for_self_signed+0x2ea/0x480 crypto/asymmetric_keys/x509_public_key.c:141 x509_cert_parse+0x46a/0x620 crypto/asymmetric_keys/x509_cert_parser.c:129 x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174 asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388 key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850 SYSC_add_key security/keys/keyctl.c:122 [inline] SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62 entry_SYSCALL_64_fastpath+0x1f/0x96 Allocated by task 196: __do_kmalloc mm/slab.c:3711 [inline] __kmalloc_track_caller+0x118/0x2e0 mm/slab.c:3726 kmemdup+0x17/0x40 mm/util.c:118 kmemdup ./include/linux/string.h:414 [inline] x509_cert_parse+0x2cb/0x620 crypto/asymmetric_keys/x509_cert_parser.c:106 x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174 asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388 key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850 SYSC_add_key security/keys/keyctl.c:122 [inline] SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62 entry_SYSCALL_64_fastpath+0x1f/0x96 Fixes: 5a7de973 ("crypto: rsa - return raw integers for the ASN.1 parser") Cc: Tudor Ambarus <tudor-dan.ambarus@nxp.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Reviewed-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Martin Kaiser authored
commit 18f77393 upstream. When fsl-imx25-tsadc is compiled as a module, loading, unloading and reloading the module will lead to a crash. Unable to handle kernel paging request at virtual address bf005430 [<c004df6c>] (irq_find_matching_fwspec) from [<c028d5ec>] (of_irq_get+0x58/0x74) [<c028d594>] (of_irq_get) from [<c01ff970>] (platform_get_irq+0x48/0xc8) [<c01ff928>] (platform_get_irq) from [<bf00e33c>] (mx25_tsadc_probe+0x220/0x2f4 [fsl_imx25_tsadc]) irq_find_matching_fwspec() loops over all registered irq domains. The irq domain is still registered from last time the module was loaded but the pointer to its operations is invalid after the module was unloaded. Add a removal function which clears the irq handler and removes the irq domain. With this cleanup in place, it's possible to unload and reload the module. Signed-off-by:
Martin Kaiser <martin@kaiser.cx> Reviewed-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
- 16 Dec, 2017 4 commits
-
-
Greg Kroah-Hartman authored
-
Leon Romanovsky authored
[ Upstream commit 7d7d065a ] Chelsio cxgb4 HW is big-endian, hence there is need to properly annotate r2 and stag fields as __be32 and not __u32 to fix the following sparse warnings. drivers/infiniband/hw/cxgb4/qp.c:614:16: warning: incorrect type in assignment (different base types) expected unsigned int [unsigned] [usertype] r2 got restricted __be32 [usertype] <noident> drivers/infiniband/hw/cxgb4/qp.c:615:18: warning: incorrect type in assignment (different base types) expected unsigned int [unsigned] [usertype] stag got restricted __be32 [usertype] <noident> Cc: Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Reviewed-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Zdenek Kabelac authored
[ Upstream commit 0868b99c ] When bitmap is resized, the old kalloced chunks just are not released once the resized bitmap starts to use new space. This fixes in particular kmemleak reports like this one: unreferenced object 0xffff8f4311e9c000 (size 4096): comm "lvm", pid 19333, jiffies 4295263268 (age 528.265s) hex dump (first 32 bytes): 02 80 02 80 02 80 02 80 02 80 02 80 02 80 02 80 ................ 02 80 02 80 02 80 02 80 02 80 02 80 02 80 02 80 ................ backtrace: [<ffffffffa69471ca>] kmemleak_alloc+0x4a/0xa0 [<ffffffffa628c10e>] kmem_cache_alloc_trace+0x14e/0x2e0 [<ffffffffa676cfec>] bitmap_checkpage+0x7c/0x110 [<ffffffffa676d0c5>] bitmap_get_counter+0x45/0xd0 [<ffffffffa676d6b3>] bitmap_set_memory_bits+0x43/0xe0 [<ffffffffa676e41c>] bitmap_init_from_disk+0x23c/0x530 [<ffffffffa676f1ae>] bitmap_load+0xbe/0x160 [<ffffffffc04c47d3>] raid_preresume+0x203/0x2f0 [dm_raid] [<ffffffffa677762f>] dm_table_resume_targets+0x4f/0xe0 [<ffffffffa6774b52>] dm_resume+0x122/0x140 [<ffffffffa6779b9f>] dev_suspend+0x18f/0x290 [<ffffffffa677a3a7>] ctl_ioctl+0x287/0x560 [<ffffffffa677a693>] dm_ctl_ioctl+0x13/0x20 [<ffffffffa62d6b46>] do_vfs_ioctl+0xa6/0x750 [<ffffffffa62d7269>] SyS_ioctl+0x79/0x90 [<ffffffffa6956d41>] entry_SYSCALL_64_fastpath+0x1f/0xc2 Signed-off-by:
Zdenek Kabelac <zkabelac@redhat.com> Signed-off-by:
-
Paul Moore authored
[ Upstream commit 173743dd ] Prior to this patch we enabled audit in audit_init(), which is too late for PID 1 as the standard initcalls are run after the PID 1 task is forked. This means that we never allocate an audit_context (see audit_alloc()) for PID 1 and therefore miss a lot of audit events generated by PID 1. This patch enables audit as early as possible to help ensure that when PID 1 is forked it can allocate an audit_context if required. Reviewed-by:
Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
