- 08 Jun, 2021 17 commits
-
-
Peng Li authored
This patch removes redundant braces {}, to fix the checkpatch.pl warning: "braces {} are not necessary for single statement blocks". Signed-off-by:Peng Li <lipeng321@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Peng Li authored
Add spaces required around that '=' and '*'. Signed-off-by:
-
Peng Li authored
Macros with complex values should be enclosed in parentheses. space required after that ',' . Signed-off-by:
-
Peng Li authored
Code indent should use tabs where possible. Signed-off-by:
-
Peng Li authored
This patch removes trailing whitespaces. Signed-off-by:
-
Peng Li authored
Networking block comments don't use an empty /* line, use /* Comment... Block comments use * on subsequent lines. Block comments use a trailing */ on a separate line. This patch fixes the comments style issues. Signed-off-by:
-
Peng Li authored
Should not initialise statics to 0. Signed-off-by:
-
Peng Li authored
Should not use assignment in if condition. Signed-off-by:
-
Peng Li authored
Fix the checkpatch error as "foo * bar" should be "foo *bar". Signed-off-by:
-
Peng Li authored
This patch fixes the checkpatch error about missing a blank line after declarations. Signed-off-by:
-
Peng Li authored
This patch removes some redundant blank lines. Signed-off-by:
-
David S. Miller authored
Joakim Zhang says: ==================== net: phy: add dt property for realtek phy Add dt property for realtek phy. --- ChangeLogs: V1->V2: * store the desired PHYCR1/2 register value in "priv" rather than using "quirks", per Russell King suggestion, as well as can cover the bootloader setting. * change the behavior of ALDPS mode, default is disabled, add dt property for users to enable it. * fix dt binding yaml build issues. ==================== Signed-off-by: -
Joakim Zhang authored
PHY will delay about 11.5ms to generate RXC clock when switching from power down to normal operation. Read/write registers would also cause RXC become unstable and stop for a while during this process. Realtek engineer suggests 15ms or more delay can workaround this issue. Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by:
-
Joakim Zhang authored
If enable Advance Link Down Power Saving (ALDPS) mode, it will change crystal/clock behavior, which cause RXC clock stop for dozens to hundreds of miliseconds. This is comfirmed by Realtek engineer. For some MACs, it needs RXC clock to support RX logic, after this patch, PHY can generate continuous RXC clock during auto-negotiation. ALDPS default is disabled after hardware reset, it's more reasonable to add a property to enable this feature, since ALDPS would introduce side effect. This patch adds dt property "realtek,aldps-enable" to enable ALDPS mode per users' requirement. Jisheng Zhang enables this feature, changes the default behavior. Since mine patch breaks the rule that new implementation should not break existing design, so Cc'ed let him know to see if it can be accepted. Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by:
-
Joakim Zhang authored
CLKOUT is enabled by default after PHY hardware reset, this patch adds "realtek,clkout-disable" property for user to disable CLKOUT clock to save PHY power. Per RTL8211F guide, a PHY reset should be issued after setting these bits in PHYCR2 register. After this patch, CLKOUT clock output to be disabled. Signed-off-by:
-
Joakim Zhang authored
Add binding for realtek rtl82xx phy. Signed-off-by:
-
Marek Behún authored
The BAREUDP config option uses spaces instead of tabs for indentation. The rest of this file uses tabs. Fix this. Signed-off-by:
Marek Behún <kabel@kernel.org> Signed-off-by:
-
- 07 Jun, 2021 23 commits
-
-
David S. Miller authored
Matteo Croce says: ==================== page_pool: recycle buffers This is a respin of [1] This patchset shows the plans for allowing page_pool to handle and maintain DMA map/unmap of the pages it serves to the driver. For this to work a return hook in the network core is introduced. The overall purpose is to simplify drivers, by providing a page allocation API that does recycling, such that each driver doesn't have to reinvent its own recycling scheme. Using page_pool in a driver does not require implementing XDP support, but it makes it trivially easy to do so. Instead of allocating buffers specifically for SKBs we now allocate a generic buffer and either wrap it on an SKB (via build_skb) or create an XDP frame. The recycling code leverages the XDP recycle APIs. The Marvell mvpp2 and mvneta drivers are used in this patchset to demonstrate how to use the API, and tested on a MacchiatoBIN and EspressoBIN boards respectively. Please let this going in on a future -rc1 so to allow enough time to have wider tests. v7 -> v8: - use page->lru.next instead of page->index for pfmemalloc - remove conditional include - rework page_pool_return_skb_page() so to have less conversions between page and addresses, and call compound_head() only once - move some code from skb_free_head() to a new helper skb_pp_recycle() - misc fixes v6 -> v7: - refresh patches against net-next - remove a redundant call to virt_to_head_page() - update mvneta benchmarks v5 -> v6: - preserve pfmemalloc bit when setting signature - fix typo in mvneta - rebase on next-next with the new cache - don't clear the skb->pp_recycle in pskb_expand_head() v4 -> v5: - move the signature so it doesn't alias with page->mapping - use an invalid pointer as magic - incorporate Matthew Wilcox's changes for pfmemalloc pages - move the __skb_frag_unref() changes to a preliminary patch - refactor some cpp directives - only attempt recycling if skb->head_frag - clear skb->pp_recycle in pskb_expand_head() v3 -> v4: - store a pointer to page_pool instead of xdp_mem_info - drop a patch which reduces xdp_mem_info size - do the recycling in the page_pool code instead of xdp_return - remove some unused headers include - remove some useless forward declaration v2 -> v3: - added missing SOBs - CCed the MM people v1 -> v2: - fix a commit message - avoid setting pp_recycle multiple times on mvneta - squash two patches to avoid breaking bisect ==================== Signed-off-by: -
Matteo Croce authored
Use the new recycling API for page_pool. In a drop rate test, the packet rate increased by 10%, from 296 Kpps to 326 Kpps. perf top on a stock system shows: Overhead Shared Object Symbol 23.66% [kernel] [k] __pi___inval_dcache_area 22.85% [mvneta] [k] mvneta_rx_swbm 7.54% [kernel] [k] kmem_cache_alloc 6.49% [kernel] [k] eth_type_trans 3.94% [kernel] [k] dev_gro_receive 3.91% [kernel] [k] __netif_receive_skb_core 3.91% [kernel] [k] kmem_cache_free 3.76% [kernel] [k] page_pool_release_page 3.56% [kernel] [k] free_unref_page 2.40% [kernel] [k] build_skb 1.49% [kernel] [k] skb_release_data 1.45% [kernel] [k] __alloc_pages_bulk 1.30% [kernel] [k] page_frag_free And this is the same output with recycling enabled: Overhead Shared Object Symbol 26.41% [kernel] [k] __pi___inval_dcache_area 25.00% [mvneta] [k] mvneta_rx_swbm 8.14% [kernel] [k] kmem_cache_alloc 6.84% [kernel] [k] eth_type_trans 4.44% [kernel] [k] __netif_receive_skb_core 4.38% [kernel] [k] kmem_cache_free 4.16% [kernel] [k] dev_gro_receive 3.21% [kernel] [k] page_pool_put_page 2.41% [kernel] [k] build_skb 1.82% [kernel] [k] skb_release_data 1.61% [kernel] [k] napi_gro_receive 1.25% [kernel] [k] page_pool_refill_alloc_cache 1.16% [kernel] [k] __netif_receive_skb_list_core We can see that page_pool_release_page(), free_unref_page() and __alloc_pages_bulk() are no longer on top of the list when receiving traffic. The test was done with mausezahn on the TX side with 64 byte raw ethernet frames. Signed-off-by:
Matteo Croce <mcroce@microsoft.com> Signed-off-by:
-
Matteo Croce authored
Use the new recycling API for page_pool. In a drop rate test, the packet rate is almost doubled, from 1110 Kpps to 2128 Kpps. perf top on a stock system shows: Overhead Shared Object Symbol 34.88% [kernel] [k] page_pool_release_page 8.06% [kernel] [k] free_unref_page 6.42% [mvpp2] [k] mvpp2_rx 6.07% [kernel] [k] eth_type_trans 5.18% [kernel] [k] __netif_receive_skb_core 4.95% [kernel] [k] build_skb 4.88% [kernel] [k] kmem_cache_free 3.97% [kernel] [k] kmem_cache_alloc 3.45% [kernel] [k] dev_gro_receive 2.73% [kernel] [k] page_frag_free 2.07% [kernel] [k] __alloc_pages_bulk 1.99% [kernel] [k] arch_local_irq_save 1.84% [kernel] [k] skb_release_data 1.20% [kernel] [k] netif_receive_skb_list_internal With packet rate stable at 1100 Kpps: tx: 0 bps 0 pps rx: 532.7 Mbps 1110 Kpps tx: 0 bps 0 pps rx: 532.6 Mbps 1110 Kpps tx: 0 bps 0 pps rx: 532.4 Mbps 1109 Kpps tx: 0 bps 0 pps rx: 532.1 Mbps 1109 Kpps tx: 0 bps 0 pps rx: 531.9 Mbps 1108 Kpps tx: 0 bps 0 pps rx: 531.9 Mbps 1108 Kpps And this is the same output with recycling enabled: Overhead Shared Object Symbol 12.91% [kernel] [k] eth_type_trans 12.54% [mvpp2] [k] mvpp2_rx 9.67% [kernel] [k] build_skb 9.63% [kernel] [k] __netif_receive_skb_core 8.44% [kernel] [k] page_pool_put_page 8.07% [kernel] [k] kmem_cache_free 7.79% [kernel] [k] kmem_cache_alloc 6.86% [kernel] [k] dev_gro_receive 3.19% [kernel] [k] skb_release_data 2.41% [kernel] [k] netif_receive_skb_list_internal 2.18% [kernel] [k] page_pool_refill_alloc_cache 1.76% [kernel] [k] napi_gro_receive 1.61% [kernel] [k] kfree_skb 1.20% [kernel] [k] dma_sync_single_for_device 1.16% [mvpp2] [k] mvpp2_poll 1.12% [mvpp2] [k] mvpp2_read With packet rate above 2100 Kpps: tx: 0 bps 0 pps rx: 1021 Mbps 2128 Kpps tx: 0 bps 0 pps rx: 1021 Mbps 2127 Kpps tx: 0 bps 0 pps rx: 1021 Mbps 2128 Kpps tx: 0 bps 0 pps rx: 1021 Mbps 2128 Kpps tx: 0 bps 0 pps rx: 1022 Mbps 2128 Kpps tx: 0 bps 0 pps rx: 1022 Mbps 2129 Kpps The major performance increase is explained by the fact that the most CPU consuming functions (page_pool_release_page, page_frag_free and free_unref_page) are no longer called on a per packet basis. The test was done by sending to the macchiatobin 64 byte ethernet frames with an invalid ethertype, so the packets are dropped early in the RX path. Signed-off-by:
-
Ilias Apalodimas authored
Up to now several high speed NICs have custom mechanisms of recycling the allocated memory they use for their payloads. Our page_pool API already has recycling capabilities that are always used when we are running in 'XDP mode'. So let's tweak the API and the kernel network stack slightly and allow the recycling to happen even during the standard operation. The API doesn't take into account 'split page' policies used by those drivers currently, but can be extended once we have users for that. The idea is to be able to intercept the packet on skb_release_data(). If it's a buffer coming from our page_pool API recycle it back to the pool for further usage or just release the packet entirely. To achieve that we introduce a bit in struct sk_buff (pp_recycle:1) and a field in struct page (page->pp) to store the page_pool pointer. Storing the information in page->pp allows us to recycle both SKBs and their fragments. We could have skipped the skb bit entirely, since identical information can bederived from struct page. However, in an effort to affect the free path as less as possible, reading a single bit in the skb which is already in cache, is better that trying to derive identical information for the page stored data. The driver or page_pool has to take care of the sync operations on it's own during the buffer recycling since the buffer is, after opting-in to the recycling, never unmapped. Since the gain on the drivers depends on the architecture, we are not enabling recycling by default if the page_pool API is used on a driver. In order to enable recycling the driver must call skb_mark_for_recycle() to store the information we need for recycling in page->pp and enabling the recycling bit, or page_pool_store_mem_info() for a fragment. Co-developed-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by:
-
Matteo Croce authored
This is a prerequisite patch, the next one is enabling recycling of skbs and fragments. Add an extra argument on __skb_frag_unref() to handle recycling, and update the current users of the function with that. Signed-off-by:
-
Matteo Croce authored
This is needed by the page_pool to avoid recycling a page not allocated via page_pool. The page->signature field is aliased to page->lru.next and page->compound_head, but it can't be set by mistake because the signature value is a bad pointer, and can't trigger a false positive in PageTail() because the last bit is 0. Co-developed-by:
Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by:
-
Yang Yingliang authored
Use devm_platform_get_and_ioremap_resource() to simplify code and avoid a null-ptr-deref by checking 'res' in it. Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
-
Zheng Yongjun authored
Fix some spelling mistakes in comments: negociated ==> negotiated dont ==> don't Signed-off-by:
Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by:
-
Zheng Yongjun authored
Fix some spelling mistakes in comments: constuct ==> construct chanels ==> channels Detination ==> Destination Signed-off-by:
-
Zheng Yongjun authored
Fix some spelling mistakes in comments: Dont ==> Don't timout ==> timeout incomming ==> incoming necesarry ==> necessary substract ==> subtract Signed-off-by:
-
Zheng Yongjun authored
Fix some spelling mistakes in comments: Interate ==> Iterate sucess ==> success Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Yang Yingliang authored
It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Signed-off-by:
-
Yang Yingliang authored
It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Signed-off-by:
-
Yang Yingliang authored
Use the devm_platform_ioremap_resource_byname() helper instead of calling platform_get_resource_byname() and devm_ioremap_resource() separately. Signed-off-by:
-
Yang Yingliang authored
Use devm_platform_get_and_ioremap_resource() to simplify code. Signed-off-by:
-
Yang Yingliang authored
Use devm_platform_get_and_ioremap_resource() to simplify code. Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
Yang Yingliang authored
It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Shaokun Zhang authored
Function 'pnic2_lnk_change' is declared twice, so remove the repeated declaration. Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by:
-
Yang Yingliang authored
It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: refactors and decouples the error handling logic This patchset refactors and decouples the error handling logic from reset logic, it is the preset patch of the RAS feature. It mainly implements the function that reset logic remains independent of the error handling logic, this will ensure that common misellaneous MSI-X interrupt are re-enabled quickly. ==================== Signed-off-by: -
Yufeng Mo authored
Earlier patches have decoupled the MSI-X conveyed error handling and recovery logic. This earlier concept code is no longer required. Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
-
Jiaran Zhang authored
Error handling & recovery is done in context of reset task which gets scheduled from misc interrupt handler in existing code. But since error handling has been moved to new task, it should get scheduled instead of the reset task from the interrupt handler. Signed-off-by:
-
Jiaran Zhang authored
Error handling and recovery logic are intertwined. Error handling (i.e. error identification, clearing error sources and initiation of recovery) is done in context of reset task. If certain hardware errors get delivered during driver init time, which can cause driver init/loading to fail. Introduce a separate error handling task to ensure below: 1. Reset logic remains independent of the error handling logic. 2. Add the hclge_errhand_task_schedule to schedule error recovery tasks, This will ensure that common misellaneous MSI-X interrupt are re-enabled quickly. Signed-off-by:
-
