- 24 Sep, 2007 2 commits
-
-
Pavel Pisa authored
The patch enables to define MMC host get_ro() method through platform data. Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Add a led trigger for each host controller that indicates if there is a request active on the controller. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
- 23 Sep, 2007 38 commits
-
-
David Brownell authored
This is the latest version of the MMC-over-SPI support. It works on 2.6.23-rc2 plus git-mmc (from rc1-mm2), along with the preceding patches which teach the rest of the MMC stack about SPI. The main issue of note is that sometimes cards need to be power cycled to recover after certain faults. Also, it may sometimes be necessary to disable CRCs. ("modprobe mmc_core use_spi_crc=n") Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: mikael.starvik@axis.com, Cc: Hans-Peter Nilsson <hp@axis.com> Cc: Jan Nikitenko <jan.nikitenko@gmail.com> Cc: Mike Lavender <mike@steroidmicros.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
David Brownell authored
Teach the MMC/SD/SDIO core about using SPI mode. - Use mmc_host_is_spi() so enumeration works through SPI signaling and protocols, not just the native versions. - Provide the SPI response type flags with each request issued, including requests from the new lock/unlock code. - Understand that cmd->resp[0] and mmc_get_status() results for SPI return different values than for "native" MMC/SD protocol; this affects resetting, checking card lock status, and some others. - Understand that some commands act a bit differently ... notably: * OP_COND command doesn't return the OCR * APP_CMD status doesn't have an R1_APP_CMD analogue Those changes required some new and updated primitives: - Provide utilities to access two SPI-only requests, and one request that wasn't previously needed: * mmc_spi_read_ocr() ... SPI only * mmc_spi_set_crc() ... SPI only (override by module parm) * mmc_send_cid() ... for use without broadcast mode - Updated internal routines: * Previous mmc_send_csd() modified into mmc_send_cxd_native(); it uses native "R2" responses, which include 16 bytes of data. * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data() helper for command-and-data access * Bugfix to that mmc_send_cxd_data() code: dma-to-stack is unsafe/nonportable, so kmalloc a bounce buffer instead. - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use those helper routines based on whether they're native or SPI The newest categories of cards supported by the MMC stack aren't expected to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO. All those cards support SPI mode, so eventually they should work too. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
David Brownell authored
Teaching the MMC/SD block card driver about SPI. - Provide the SPI response type flags with each request issued. - Understand that multiblock SPI writes don't use STOP_TRANSMISSION. - Correct check for APP_CMD failure. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
David Brownell authored
Teach the MMC/SD/SDIO system headers that some hosts use SPI mode - New host capabilities and status bits * MMC_CAP_SPI, with mmc_host_is_spi() test * mmc_host.use_spi_crc flag - SPI-specific declarations: * Response types, MMC_RSP_SPI_R* * Two SPI-only commands * Status bits used native to SPI: R1_SPI_*, R2_SPI_* - Fix a few (unrelated) whitespace bugs in the headers. - Reorder a few mmc_host fields, removing several bytes of padding None of these changes affect current code. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Store vendor strings found in CISTPL_VERS_1 so that function drivers can access them. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Increase delay for power up in order to support some slower boards. Also add some comments about why the delays are there. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Add support for relaying the sdio interrupt signal from the card. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
In a few places, sdio_uart_irq() is called directly instead of waiting for the actual interrupt to be raised and the SDIO IRQ thread scheduled in order to reduce latency. However, some interaction with the tty core may end up calling us back (serial echo, flow control, etc.) creating two issues: - the host lock gets claimed twice from the same thread causing a deadlock; - the same direct calls to sdio_uart_irq() may be performed causing unexpected reentrancy into the IRQ handler. This patch handles both of those issues. Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
Note that the default baudrate is 4800 instead of 9600 as a convenience because that's what GPS devices want which is still the main use for this driver. Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
David Vrabel authored
Add sdio_f0_readb() and sdio_f0_writeb() functions to reading and writing function 0 registers. Writes outside the vendor specific CCCR registers (0xF0 - 0xFF) are not permitted. Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Replace all cases of BUG_ON with WARN_ON where there is a chance (with varying degrees of slim) that the kernel can continue without incidence. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Mariusz Kozlowski authored
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
David Vrabel authored
Extend sdio_readsb(), sdio_writesb(), sdio_memcpy_fromio(), and sdio_memcpy_toio() to handle any length of buffer by splitting the transfer into several IO_RW_EXTENDED commands. Typically, a transfer would be split into a single block mode transfer followed by a byte mode transfer for the remainder but we also handle lack of block mode support and the block size being greater than 512 (the maximum byte mode transfer size). host->max_seg_size <= host->max_req_size so there's no need to check both when determining the maximum data size for a single command. Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
David Vrabel authored
Before a driver is probed, set the function's block size to the default so the driver is sure the block size is something sensible and it needn't explicitly set it. The default block size is the largest that's supported by both the card and the host, with a maximum of 512 to ensure aribitrarily sized transfer use the optimal (least) number of commands. See http://lkml.org/lkml/2007/8/7/150 for reasons for the block size choice. Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
David Vrabel authored
Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
SDIO doesn't have a CSD so it uses different timeout values than SD memory. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Enable 4-bit data bus mode, according to host and card capabilities. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Change clock speed to the highest supported by the card. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Adrian Bunk authored
On Wed, Jul 25, 2007 at 04:03:04AM -0700, Andrew Morton wrote: >... > Changes since 2.6.22-rc6-mm1: >... > git-mmc.patch >... > git trees >... sdio_dev_attrs[] can become static. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Support the multi-byte transfer operation, including handlers for common operations like writel()/readl(). Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
This mimics what the serial_core does. Useful for diagnostics. Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
This currently only accepts the GPS class since that's all I have for testing. Tested with a Matsushita GPS and gpsd version 2.34. Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
It is sometimes necessary to give up on trying to claim the host lock, especially if that happens in a thread that has to be stopped. While at it, fix the description for mmc_claim_host() which was wrong. Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Make the mmc bus uevent callback look like all other subsystems. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
The problem is that the sdio_bus must be registered before any SDIO drivers are registered against it otherwise the kernel sulks. Because the sdio_bus registration happens through module_init (equivalent to device_initcall), then any SDIO drivers linked before the SDIO core code in the kernel will be initialized first. Upcoming SDIO function drivers are likely to be located outside the drivers/mmc directory as it is common practice to group drivers according to their function rather than the bus they use. SDIO drivers are therefore likely to appear at random location in the kernel link. To make sure the sdio_bus is always initialized before any SDIO drivers, let's move the MMC init to the subsys_initcall level. Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Add a more clean separation between global, common CIS information and the function specific one as we need the common information in places where no specific function is specified. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
This way those tuples that the core cares about are consumed by the core code, and tuples that only function drivers might make sense of are available to drivers. Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Nicolas Pitre authored
Signed-off-by: Nicolas Pitre <npitre@mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-
Pierre Ossman authored
Like many other buses, the devices (functions) on the SDIO bus must be enabled before they can be used. Add functions that allow drivers to do so. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
-