To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.

Tested this EEH patch with Intel 10G pci-express ixgbe adapter.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The lower limit of 80 descriptors in the ring is only valid for
one older 8254x chipset. All e1000e devices can use as low as
64 descriptors.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Several components to this complex fix. The es2lan cards occasionally
gave a "HW Error" especially when forcing speed. Some users also
reported that the BMC stole ARP packets.

The fixes include setting the proper SW_FW bits to tell the BMC
that we're active and not do any un-initialization at all, so the
setup routine is largely changed.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The ethtool -c / -C interface can now be used to modify the
irq moderation algorithm. This change does not require an
adapter reset and can thus be used at all times. The adapter
only supports changing/reading rx-usecs which has special
values for 0, 1 and 3:

0 - no irq moderation whatsoever
1 - normal moderation favoring regular mixed traffic (default)
3 - best attempt at low latency possible at cost of CPU

For values between 10 and 10000 the rx-usecs defines "the minimum
time between successive irqs" in usec, unlike the module parameter.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Several stats registers are completely unused and we just waste pci
bus time reading them. We also omit using the high 32 bits of the GORC/
GOTC counters. We can just read clear them and only read the low registers.

Mii-tool can also break es2lan if it executes a MII PHY register
ioctl while the device is in autonegotiation. Unfortunately it seems
that several applications and installations still perform this ioctl
call periodically and especially in this crucial startup time. We
can fool the ioctl by providing fail safe information that mimics
the "down" link state and only perform the dangerous PHY reads once
after link comes up to fill in the real values. As long as link
stays up the information will not change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

- Removed rx_lock and put_lock as the buffer replenishment and
  receive completion is handled serially.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

- Removed receive buffer replenishment tasklet s2io_tasklet and instead
  allocating the receive buffers in either the interrupt handler (no napi)
  or the napi handler (napi enabled).
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

- Updated version number.
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

- Fix the memory leak during free_tx_buffers.
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The patch that changed mdio_bus to a string didn't conflict strongly enough
with the patch that added fixed PHY support to UCC.  Gather it back into
the fold.

Fixes this error:
...
 CC      drivers/net/ucc_geth.o
 'ucc_geth_probe':
 /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/net/ucc_geth.c:3935: error:
 incompatible types in assignment
 make[3]: *** [drivers/net/ucc_geth.o] Error 1
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

net/key/af_key.c: In function ‘pfkey_spddelete’:
net/key/af_key.c:2359: warning: ‘pol_ctx’ may be used uninitialized in 
this function

When CONFIG_SECURITY_NETWORK_XFRM isn't set, 
security_xfrm_policy_alloc() is an inline that doesn't set pol_ctx, so 
this seemed like the easiest fix short of using *uninitialized_var(pol_ctx).
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since these operations don't go through the normal
device calls, we have to ensure we synchronize with
those paths.

Noticed by Alan Cox.
Signed-off-by: David S. Miller <davem@davemloft.net>

Plan C: we can follow the Al Viro's proposal about %n like in this patch.
The same applies to udp, fib (the /proc/net/route file), rt_cache and 
sctp debug. This is minus ~150-200 bytes for each.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When drivers call request_module(), it tries to do something with UNIX
sockets and triggers a 'runaway loop modprobe net-pf-1' warning. Avoid
this by initialising AF_UNIX support earlier.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ASSERT_RTNL uses mutex_trylock to test whether the rtnl_mutex is
held. This bogus warnings when running in atomic context, which
f.e. happens when adding secondary unicast addresses through
macvlan or vlan or when synchronizing multicast addresses from
wireless devices.

Mid-term we might want to consider moving all address updates
to process context since the locking seems overly complicated,
for now just fix the bogus warning by changing ASSERT_RTNL to
use mutex_is_locked().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

On Wed, 2008-04-23 at 13:38 +0300, Tomas Winkler wrote:
> This patch fixes problem in Makefile that prevented
> built-in compilation of iwlcore

Here is the second part. Without this,
drivers/net/wireless/iwlwifi/build-in.o will not be linked into vmlinux.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Noticed by Alan Cox.

The IFF_UP test is a bit racey, because other entities
outside of this driver's ioctl handler can modify that
state, even though this ioctl handler runs under
lock_kernel().
Signed-off-by: David S. Miller <davem@davemloft.net>

Use stats which now is in the net_device instead of one declared in
ppp structure.
Kill ppp_net_stats function, because by default it is used identical
internal_stats function from net/core/dev.c
Signed-of-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b716bb91 ("iwlwifi: Cancel scanning upon association") moved the
test of priv->vif in iwl{3945,4964}_mac_config_interface() outside of
where priv->mutex is held, but still tries to do mutex_unlock() on
return.  This is clearly wrong and triggers a nasty lockdep warning when
this codepath is triggered.  Fix this by removing the mutex_unlock().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

priv->param_workaround_interval is unsigned, modparam_workaround_interval not.
the former is never < 0.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

previously in this function:

u32 index = (dwrq->flags & IW_ENCODE_INDEX) - 1;

index is unsigned, so if -1, the original test (below) didn't work.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates mesh EID values, some of which where conflicting with
already-approved 11h EIDs (pointed out by Tomas Winkler). I wanted to use the
values suggested in the last available 802.11 draft (2.0) but it assigns 50 to
MESH_CONFIG, the same value than EXT_SUPP_RATES. Using the values proposed in
the draft incremented by one.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some mainboards/CPUs don't allow DMA masks bigger than a certain limit.
Some VIA crap^h^h^h^hdevices have an upper limit of 0xFFFFFFFF. So in this
case a 64-bit b43 device would always fail to acquire the mask.
Implement a workaround to fallback to lower DMA mask, as we can always
also support a lower mask.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes use of Qdisc length in requeue function, before we checked
the reference is valid. (Adrian Bunk's catch)
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes an off-by-one in net/mac80211/rx.c introduced by
commit 8318d78a
(cfg80211 API for channels/bitrates, mac80211 and driver conversion)
and spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The put routine first decrements the users counter and then
(if it is zero) locks the sta_bss_lock and removes one from
the list and the hash.

Thus, any of ieee80211_sta_config_auth, ieee80211_rx_bss_get
or ieee80211_rx_mesh_bss_get can race with it by finding a
bss that is about to get kfree-ed.

Using atomic_dec_and_lock in ieee80211_rx_bss_put takes care
of this race.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 *Fix radio chip identification on AR5424/2424 during ath5k_hw_attach
 *Try to assign an RF2413 radio on AR2424 for testing

 Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the SSB SPROM a field set to all ones means the value
is not defined in the SPROM.
In case of the boardflags, we need to set them to zero
to avoid confusing drivers. Drivers will only check the
flags by ANDing.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Gabor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds more workarounds for devices with broken BT bits.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The HostFlags are a bitmask of 48bit. So we must use an u64 datatype
to hold all bits.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a workaround for invalid bluetooth SPROM settings
on ASUS PCI cards.
This will stop the microcode from poking with the BT GPIO line.
This fixes data transmission on this device, as the BT GPIO line
is used for something TX related on this device
(probably the power amplifier or the radio).
This also adds a modparam knob to help debugging this in the future,
as more devices with this bug may show up.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This updates the mac80211 maintainers entry to
 1) remove Jiri
 2) put me first
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Cc: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are two structures named wmm_info and wmm_param, they are used while
parsing the beacon frame. (Check the function ieee802_11_parse_elems).
Certain APs like D-link does not set the fifth bit in WMM IE.
While sending the association request to n-only ap it checks for wmm_ie.
If it is set then only ieee80211_ht_cap is sent during association request.
So n-only association fails.
And this patch fixes this problem by copying the wmm_info to wmm_ie,
which enables the "wmm" flag in iee80211_send_assoc.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes problem in Makefile that prevented
built-in compilation of iwlcore

Commit that caused this problem: eadd3c4b ("iwlwifi: make Makefile
more concise")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Yi Zhu <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the removal of the Solaris binary emulation the exports of 
move_addr_to_{kernel,user} are no longer used.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

The LEDS infrastructure itself does not require anything
that a platform dependant upon HAS_IOMEM.

The individual drivers do, but they are properly guarded
with the necessary platform dependencies.

One can even imagine a hypervisor based LED driver that
a platform without HAS_IOMEM might have.
Signed-off-by: David S. Miller <davem@davemloft.net>

As it stands it's impossible to use any authentication algorithms
with an ID above 31 portably.  It just happens to work on x86 but
fails miserably on ppc64.

The reason is that we're using a bit mask to check the algorithm
ID but the mask is only 32 bits wide.

After looking at how this is used in the field, I have concluded
that in the long term we should phase out state matching by IDs
because this is made superfluous by the reqid feature.  For current
applications, the best solution IMHO is to allow all algorithms when
the bit masks are all ~0.

The following patch does exactly that.

This bug was identified by IBM when testing on the ppc64 platform
using the NULL authentication algorithm which has an ID of 251.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>