The ESCR and OTAR registers are not present in all DU channels on Gen3
SoCs. ESCR only exists in channels that can be routed to an LVDS or
DPAD, and OTAR in channels that can be routed to a DPAD. Skip writing
those registers for other channels. This replaces the DU gen check, as
Gen4 doesn't have LVDS or DPAD outputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>

On R-Car D3 and E3, the LVDS encoder provides the dot (pixel) clock to
the DU, regardless of whether the LVDS output is used or not. When using
the DPAD (RGB) output, the DU driver thus enables and disables the LVDS
PLL manually, while when using the LVDS output, it lets the LVDS bridge
driver handle the PLL configuration internally as part of the atomic
enable and disable operations.

This causes an issue when using the LVDS output. As bridges are disabled
before CRTCs, the current implementation violates the enable/disable
sequences documented in the hardware datasheet, which requires the dot
clock to be enabled before the CRTC is started and disabled after it
gets stopped.

Fix the problem by enabling/disabling the LVDS PLL manually from the DU
regardless of which output is used, and skipping the PLL handling in the
LVDS bridge atomic enable and disable operations.

This is however not enough. Disabling the LVDS encoder while leaving the
PLL on still results in a vertical blanking wait timeout when disabling
the DU. Investigation showed that the culprit is the LVEN bit. For an
unclear reason, clearing the bit when disabling the LVDS encoder blocks
vertical blanking interrupts. We thus have to delay disabling the whole
LVDS encoder, not just disabling the PLL, until the DU is disabled.

We could split the LVDS disable sequence by clearing the LVRES bit in
the LVDS bridge atomic disable handler, and delaying the rest of the
operations, in order to disable the LVDS output at bridge atomic disable
time, before stopping the CRTC. This would make the code more complex,
without a clear benefit, so keep the implementation simple(r).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>

To prepare for a rework of the LVDS disable code, which will need to be
called from rcar_lvds_pclk_disable(), move the LVDS enable code,
currently stored in the __rcar_lvds_atomic_enable() function, to a
separate code section separate from bridge operations. It will be then
extended with the LVDS disable code.

As part of this rework the __rcar_lvds_atomic_enable() function is
renamed to rcar_lvds_enable() to more clearly indicate its purpose.

No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>

When disabling the companion bridge in rcar_lvds_atomic_disable(),
there's no need to go through the bridge's operations to call
.atomic_disable(). Call rcar_lvds_atomic_disable() on the companion
directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>

Core Changes:
- drm: Add SDP Error Detection Configuration Register (Arun)

Driver Changes:
- Meteor Lake enabling and fixes (RK, Jose, Madhumitha)
- Lock the fbdev obj before vma pin (Tejas)
- DSC fixes (Stanislav)
- Fixes and clean-up on opregion code (Imre)
- More wm/vblank stuff (Ville)
- More general display code organization (Jani)
- DP Fixes (Stanislav, Ville)
- Introduce flags to ignore long HPD and link training issues \
  for handling spurious issues on CI (Vinod)
- Plane cleanups and extra registers (Ville)
- Update audio keepalive clock values (Clint)
- Rename find_section to bdb_find_section (Maarten)
- DP SDP CRC16 for 128b132b link layer (Arun)
- Fix various issues with noarm register writes (Ville)
- Fix a few TypeC / MST issues (Imre)
- Create GSC submission targeting HDCP and PXP usages on MTL+ (Suraj)
- Enable HDCP2.x via GSC CS (Suraj)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZBy56qc9C00tCLOY@intel.com

drm-misc-next for v6.4-rc1:

Core Changes:
- Add unit test for xrgb8888 to mono.
- Assorted small fixes to format helper selftests.
- Assorted documentation updates.
- Drop drm_dev_set_unique.
- Always use shadow buffer in generic fbdev emulation helpers, and
  improve error handling.

Driver Changes:
- Assorted small fixes to malidp, hdlcd, gma500, lima, bridge, rockchip.
- Move fbdev in gma500 to use drm_client.
- Convert bridge platform callbacks to void return.
- Drop leftover from vgem to shmem helper conversion.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5a4c438e-7047-c044-fc77-5a3597000264@linux.intel.com

MTL uses GSC command streamer i.e gsc cs to send HDCP/PXP commands
to GSC f/w. It requires to keep hdcp display driver
agnostic to content protection f/w (ME/GSC fw) in the form of
i915_hdcp_fw_ops generic ops.

Adding HDCP GSC CS interface by leveraging the i915_hdcp_fw_ops generic
ops instead of I915_HDCP_COMPONENT as integral part of i915.

Adding checks to see if GSC is loaded and proxy is setup

--v6
-dont change the license date in same patch series [Jani]
-fix the license year {Jani]

--v8
-remove stale comment [Ankit]
-get headers in alphabetical order [Ankit]
-fix hdcp2_supported check [Ankit]

--v9
-remove return statement from hdcp_gsc_fini [Ankit]

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-7-suraj.kandpal@intel.com

Add function that takes care of sending command to gsc cs. We start
of with allocation of memory for our command intel_hdcp_gsc_message that
contains gsc cs memory header as directed in specs followed by the
actual payload hdcp message that we want to send.
Spec states that we need to poll pending bit of response header around
20 times each try being 50ms apart hence adding that to current
gsc_msg_send function
Also we use the same function to take care of both sending and receiving
hence no separate function to get the response.

--v4
-Create common function to fill in gsc_mtl_header [Alan]
-define host session bitmask [Alan]

--v5
-use i915 directly instead of gt->i915 [Alan]
-No need to make fields NULL as we are already
using kzalloc [Alan]

--v8
-change mechanism to reuse the same memory for one hdcp session[Alan]
-fix header ordering
-add comments to explain flags and host session mask [Alan]

--v9
-remove gem obj from hdcp message as we can use
i915_vma_unpin_and_release [Alan]
-move hdcp message allocation and deallocation from hdcp2_enable and
hdcp2_disable to init and teardown of HDCP [Alan]

--v10
-remove unnecessary i915_vma_unpin [Alan]

--v11
-fix comment style [Uma]

Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Alan Pervin Teres <alan.previn.teres.alexis@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-6-suraj.kandpal@intel.com

It requires to move intel specific HDCP API structures to
i915_hdcp_interface.h from driver/misc/mei/hdcp/mei_hdcp.h
so that any content protection fw interfaces can use these
structures.

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-5-suraj.kandpal@intel.com

There are more than 1 type of content protection security firmware.
Make the name generic
%s/_mei_/_

--v3
-Changing names to drop cp_fw to make naming more agnostic[Jani]

--v4
-remove header reference in intel_display_core.h [Uma]
-fix commit message and prefix drm [Uma]

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-4-suraj.kandpal@intel.com

pre MTL we interact with mei interface to talk to
firmware and enable CP but going forward we will talk to gsc cs
because of which we are making all names for HDCP helpers and
structures generic as either mei or gsc cs maybe used.

Change the include/drm/i915_mei_hdcp_interface.h to
include/drm/i915_hdcp_interface.h

Change the i915_hdcp_interface.h header naming convention to
suit generic f/w type.
%s/MEI_/HDCP_
%s/mei_dev/hdcp_dev

Change structure name Accordingly.
%s/i915_hdcp_comp_master/i915_hdcp_master
%s/i915_hdcp_component_ops/i915_hdcp_ops

--v6
-make each patch build individually [Jani]

--v8
-change ME FW to ME/GSC FW [Ankit]
-fix formatting issue [Ankit]

--v9
-fix commit message and header [Uma]

--v10
-rename comp variable [Uma]

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-3-suraj.kandpal@intel.com

HDCP and PXP will require a common function to allow it to
submit commands to the gsc cs. Also adding the gsc mtl header
that needs to be added on to the existing payloads of HDCP
and PXP.

--v4
-Seprate gsc load and heci cmd submission into different
functions in different files for better scalability [Alan]
-Rename gsc address field [Alan]

--v5
-remove extra line is intel_gsc_fw.h [Uma]

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: Suraj Kandpal<suraj.kandpal@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-2-suraj.kandpal@intel.com

devm_regmap_init_mmio() may return an invalid pointer in case of an error.
This patch adds the corresponding IS_ERR check to vop2->map.
Signed-off-by: Alfredo Cruz <alfredo.carlon@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230322224411.15612-1-alfredo.carlon@gmail.com

This fixes a use-after-free crash during rmmod.

The DRM encoder is embedded inside the larger rockchip_hdmi,
which is allocated with the component. The component memory
gets freed before the main drm device is destroyed. Fix it
by running encoder cleanup before tearing down its container.
Signed-off-by: Toby Chen <tobyc@nvidia.com>
[moved encoder cleanup above clk_disable, similar to bind-error-path]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230317005126.496-1-tobyc@nvidia.com

clang reportes this error
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2322:8: error:
  variable 'possible_crtcs' is used uninitialized whenever 'if'
  condition is false [-Werror,-Wsometimes-uninitialized]
                        if (vp) {
                            ^~
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2336:36: note:
  uninitialized use occurs here
                ret = vop2_plane_init(vop2, win, possible_crtcs);
                                                 ^~~~~~~~~~~~~~
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2322:4:
  note: remove the 'if' if its condition is always true
                        if (vp) {
                        ^~~~~~~~

The else-statement changes the win->type to OVERLAY without setting the
possible_crtcs variable.  Rework the block, initialize possible_crtcs to
0 to remove the else-statement.  Split the else-if-statement out to its
own if-statement so the OVERLAY check will catch when the win-type has
been changed.

Fixes: 368419a2 ("drm/rockchip: vop2: initialize possible_crtcs properly")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316132302.531724-1-trix@redhat.com

The current way to determine during HW state sanitization if a PHY is
connected in the expected way doesn't work in all cases. The check for
this considers only the PHY ready/owned state and the initial TC mode
which was determined earlier by the TC port HW readout - using the
sink's HPD and the same PHY ready/owned states.

For instance for an enabled DP-alt/TBT port without the PHY ready/owned
flags set the initial mode will be TBT, and this will be regarded as a
valid PHY state. However it's possible that the port is actually enabled
in DP-alt mode, but for some reason the PHY ownership was not acquired.

Make sure the driver can detect invalid PHY states as in the above
example by checking the PHY ready/owned state wrt. the PLL type used.
This should be the TBT PLL if the PHY is not owned and the MG (non-TBT)
PLL if the PHY is owned.

v2: Rebased on change passing crtc_state in the previous patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-3-imre.deak@intel.com

For clarity factor out the function to determine if there are active
links on a TC port. This prepares for the next patch also checking the
port's PLL type.

While at it pass crtc_state to intel_tc_port_sanitize_mode(), and check
hw.active in that, instead of the deprecated crtc->active flag.

v2: Check crtc_state->hw.active instead of crtc->active. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-2-imre.deak@intel.com

Add an encoder hook, which can be called on enabled TC ports to
determine if the port uses a TBT or a non-TBT PLL. An upcoming patch
will use this to sanity check active TC port's PHY state wrt. the PLL
type used by the port.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-13-imre.deak@intel.com

Since an HDMI output can only be enabled in legacy mode on TC ports,
assume that VBT is wrong and the port is legacy if VBT says the port is
non-legacy and has HDMI. If VBT says to enable DP as well leave the
non-legacy flag enabled, relying on the flag getting fixed up based on
the HPD status during sink detection.

v2: Fix the legacy port flag only if DP is not enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-1-imre.deak@intel.com

For consistency detect the initial TC mode in the PHY owned state the
same way this is done in the not owned state (w/o changing the
behavior). While at it, add more details to the PHY state debug print.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-11-imre.deak@intel.com

Atm, a TC port's initial mode will be read out as TBT mode in any case
the PHY ownership is not held. This isn't correct for legacy ports which
should be used only in legacy mode.

Fix the above initial mode to be disconnected mode for a legacy port and
TBT mode for DP-alt/TBT ports. Determine the port type by checking first
the HPD state and then the legacy VBT flag (so the HPD state can correct
a bogus VBT flag). If a sink is connected on a disabled port the PHY
will get also connected (switching it to legacy mode on a legacy port).

Also connect the PHY on a legacy port if it's enabled but BIOS
incorrectly left it in the disconnected state for some reason.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-10-imre.deak@intel.com

A legacy TC port can't be switched to TBT mode, even if the PHY
initialization wasn't ready yet for some reason, so prevent this.

This shouldn't normally happen as the driver waits for the IOM/TCSS
PHY initialization during driver loading and system resume.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-9-imre.deak@intel.com

Atm, the target TC mode - which the PHY should be switched to at any
point it's used - is TBT in case there is no sink connected. However
legacy ports are only used in the legacy mode regardless of the sink
connected state. Fix the mode returned by
intel_tc_port_get_target_mode() accordingly.

Despite of the above issue, the PHY got disconnected as expected in
response to a sink disconnect event, causing only a redundant
PHY disconnect->reconnect sequence whenever the port was used.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-8-imre.deak@intel.com

Factor out helpers used later in the patchset to convert an HPD
status mask to TC mode or target TC mode.

No functional changes.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-7-imre.deak@intel.com

During boot-up/system resume, the TC PHY on legacy ports will be
initialized by the IOM/TCSS firmware regardless of a sink being
connected or not (as opposed to DP-alt/TBT ports, which the FW only
inits once a sink is connected).

Wait for the above initialization to complete during HW readout, so that
connecting the PHY later will already see the expected PHY ready state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-6-imre.deak@intel.com

At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.

The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port).  If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.

Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).

As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com

The commit renaming icl_tc_phy_is_in_safe_mode() to
icl_tc_phy_take_ownership() didn't flip the function's return value
accordingly, fix this up.

This didn't cause an actual problem besides state check errors, since
the function is only used during HW readout.

Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: f53979d6 ("drm/i915/display/tc: Rename safe_mode functions ownership")
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-4-imre.deak@intel.com

An enabled TC MST port holds one TC port link reference, regardless of
the number of enabled streams on it, but the TC port HW readout takes
one reference for each active MST stream.

Fix the HW readout, taking only one reference for MST ports.

This didn't cause an actual problem, since the encoder HW readout doesn't
yet support reading out the MST HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com

On TC ports the 4ms AUX timeout combined with the 5 * 32 retry
attempts during DPCD accesses adds a 640ms delay to each access if the
sink is disconnected. This in turn slows down a modeset during which the
sink is disconnected (for instance a disabling modeset).

Prevent the above delay by aborting AUX transfers on a TC port with a
disconnected sink.

The DP 1.4a link CTS (4.2.1.5 Source Device Inactive HPD / Inactive AUX
Test") also requires not to initiate AUX transfers on disconnected DP
ports in general, however this patch doesn't change the behavior on
non-TC ports, leaving that for a follow-up.
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8279Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-2-imre.deak@intel.com

Rename symbols to match the style of other fbdev-emulation source
code. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-9-tzimmermann@suse.de

Consolidate all handling of CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM by
making the module parameter optional in drm_fb_helper.c.

Without the config option, modules can set smem_start in struct
fb_info for internal usage, but not export if to userspace. The
address can only be exported by enabling the option and setting
the module parameter. Also update the comment.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng<suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-8-tzimmermann@suse.de

Clean up fbdev and client state if the probe function fails. It
used to leak allocated resources. Also reorder the individual steps
to simplify cleanup.

v2:
	* move screen_size update into separate patches
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-7-tzimmermann@suse.de

The size of the screen memory should be equivalent to the size of
the screen's GEM buffer. Don't recalculate the value.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-6-tzimmermann@suse.de

The size of the framebuffer can either be stored in screen_info or
smem_len. Take both into account in the deferred I/O code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-5-tzimmermann@suse.de

Export the fb_info release code as drm_fb_helper_release_info(). Will
help with cleaning up failed fbdev probing.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng<suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-4-tzimmermann@suse.de

Remove the flag prefer_shadow_fbdev from struct drm_mode_config.
Drivers set this flag to enable shadow buffering in the generic
fbdev emulation. Such shadow buffering is now mandatory, so the
flag is unused.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-3-tzimmermann@suse.de

Remove all codepaths that implement fbdev output directly on GEM
buffers. Always allocate a shadow buffer in system memory and set
up deferred I/O for mmap.

The fbdev code that operated directly on GEM buffers was used by
drivers based on GEM DMA helpers. Those drivers have been migrated
to use fbdev-dma, a dedicated fbdev emulation for DMA memory. All
remaining users of fbdev-generic require shadow buffering.

Memory management of the remaining callers uses TTM, GEM SHMEM
helpers or a variant of GEM DMA helpers that is incompatible with
fbdev-dma. Therefore remove the unused codepaths from fbdev-generic
and simplify the code.

Using a shadow buffer with deferred I/O is probably the best case
for most remaining callers. Some of the TTM-based drivers might
benefit from a dedicated fbdev emulation that operates directly on
the driver's video memory.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-2-tzimmermann@suse.de

Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221622511915615@zte.com.cn

Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221621336645576@zte.com.cn

Not used by any drivers any more, the only use case in drm_dev_init()
can be inlined now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316082035.567520-2-christian.koenig@amd.com