The greybus host device id can only be read by parsing the uevent if one
wants to identify a specific host device 'or' bus. This is 'lsgb' uses
today.

This change adds a bus_id attribute so libraries can identify multiple
host devices 'or' bus if they exist.

Testing Done:
Tested on Arche,
'cat /sys/bus/greybus/devices/greysbus1/bus_id'
Signed-off-by: Sandeep Patil <sspatil@google.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

A recent commit inadvertently disabled E2EFC on all interface
connections, due to a failure to clear the ES3 bootrom quirk flags
during mode switch.

Testing Done: Verified that the CPort flags are again set to 0x7 for
non-bootrom interface connections.

Fixes: 5b638080e94e ("svc: keep interfaces registered during
mode switch")
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

All firmware packages on the Modules or Interfaces are now managed by a
special Firmware Management Protocol. The Interface Manifest shall
at least contain the Firmware Management Bundle and a Firmware
Management Protocol CPort within it.

The bundle may contain additional CPorts based on the extra
functionality required to manage firmware packages.

For example, this is how the Firmware Management Bundle of the Interface
Manifest may look like:

	; Firmware Management Bundle (Bundle 1):
	[bundle-descriptor 1]
	class = 0x16

	; (Mandatory) Firmware Management Protocol on CPort 1
	[cport-descriptor 1]
	bundle = 1
	protocol = 0x18

	; (Optional) Firmware Download Protocol on CPort 2
	[cport-descriptor 2]
	bundle = 1
	protocol = 0x17

	; (Optional) SPI protocol on CPort 3
	[cport-descriptor 3]
	bundle = 1
	protocol = 0x0b

	; (Optional) Component Authentication Protocol (CAP) on CPort 4
	[cport-descriptor 4]
	bundle = 1
	protocol = 0xXX //TBD

This patch adds the basic firmware-management bundle driver, which just
creates a firmware-management connection. Support for individual
protocols will be added separately.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Originally, idea was to use widget_type to identify jack_type.
However, suggestive way is to identify jack based on jack
attributes.

Changes already exists in codec FW to report jack attributes.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This fields actually populates jack attribute. Thus, renamed to
reflect the real purpose.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

gb_activate_tx/rx is triggered from _prepare() & gb_deactivate
from shutdown(). This may cause protocol error in case shutdown
executes without _prepare due to some hw_params failure.

Also, reorganise _prepare & _shutdown calls to make it more
readable & cleaner.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Update Makefile in response to SND_SOC_DYNAMIC_DAILINK cflag
removal.

Update files for msm-dynamic-dailink.h header file removal.

Update in response to API name changes. Also, acquire sound card
controls_rwsem before adding kcontrols to avoid deadlock.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We missed this only for bundle device, fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

For every time SVC instance is created, memories for storing the rail IDs
are allocated, however, they are not freed when the SVC is destroyed.
This patch fixes the memory leak by freeing the memory when debugfs for
SVC is no longer needed.

Testing Done:
- Check pwrmon debugfs after turning on and off SVC
Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The power rail names and counts are unnecessarily stored in the gb_svc
structure once the SVC created, this causes waste of memory usage. This
patch removes rail names and rail counts storage from th gb_svc
structure.

Testing Done:
- Validated the readings from /d/greybus/1-svc/pwrmon/*
Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Implement the new interface mailbox-event operation.

The event is sent by the SVC under certain conditions when an interface
updates its mailbox value. Specifically, this event will be used to
implement the new mode-switch functionality.

Upon reception the AP verifies that the interface is known and that the
mailbox has the expected MAILBOX_GREYBUS value. If so, the interface is
disabled before being re-enabled (re-enumerated).

Note that during mode-switch, the interface will typically already be in
a disabled state when the mailbox is written (with the ES3 bootrom being
the notable exception).
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Implement the new module inserted and removed operations.

The SVC sends these after detecting a module insertion or removal, and
in the former case after having determined the module geometry (i.e.
position and size).
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Implement the interface activation and power-down sequences.

Note that all the required SVC operations have not yet been implemented
so some stub functions are used for now.

Support for hibernating the UniPro link depends on future
power-management work so a stub function is used also for this.

Interface type handling will be refined later.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add message structures (based on the current spec) for the SVC Interface
Activate operation, and a stub function that always return the Greybus
interface type.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add stub functions for v_sys, refclk and unipro resource management.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add active state flag to avoid deactivating an interface which is
already off.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Implement controlled module removal through a new module attribute
"eject".

When a non-zero argument is written to the attribute, all interfaces of
the module are disabled (e.g. bundles are deregistered) and deactivated
(e.g. powered off) before instructing the SVC to physically eject the
module.

Note that the module device is not deregistered until the SVC has
reported the physical removal of all of its interfaces.

A new interface mutex is added to enforce interface state-change
serialisation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add Greybus module abstraction that will be used to implement controlled
module removal (eject) and represent module geometry.

Greybus module devices correspond to physical modules and have one or
more interfaces. Modules have an id that is identical to the id of their
primary interface, which in turn is the interface with lowest numbered
id. The module name is constructed from the bus and module id:

        <bus_id>-<module_id>

Interfaces, bundles, and control devices are consequently renamed as

        <bus_id>-<module_id>.<interface_id>
        <bus_id>-<module_id>.<interface_id>.<bundle_id>
        <bus_id>-<module_id>.<interface_id>.ctrl

As before, interface ids (and therefore in a sense now also module ids)
correspond to physical interface positions on the frame.

Modules have the following attributes:

        module_id
        num_interfaces

where module_id is the id of the module and num_interface the number of
interfaces the module has.

Note that until SVC module-size detection has been implemented, all
interfaces are considered to be part of 1x2 modules. Specifically, the
two interfaces of a 2x2 module will be presented as two 1x2 modules for
now.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add interface re-enable helper that is used during mode switch to
disable and re-enable (enumerate) an interface.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The attribute entries have been kept mostly sorted within each device
type. Let's move the three more-recently added interface attributes
that were not.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add an entry for the recently added interface control device.

Also move the bundle-device entry below the control-device entries.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use the common gb_svc functions also for the recently added svc
functions. Having a common prefix clearly signals where the code
resides, something which improves readability and helps during
debugging (e.g. stack traces).

Note that all functions in svc.c except for these three use the common
prefix with the exception of the pwr_debugfs callbacks (that still use
*a* common prefix) and the attribute accessors (than can not have a
common prefix due to some macro magic).
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This change was missed while merging original patch
commit-id: 53c765c33f4a69c31027ec012e717d303bd4feca
Thus submitting it again.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We have chosen the *ugly* way of registering two platform drivers from
the module_init() of only one of them, so that we can avoid having two
separate modules for them.

But we should still be doing this in a sane way. There is no need to
expose internals of arche-ctrl to arche-platform, like PM-ops, probe,
resume, id-table, etc. Just expose an init and a exit callback.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

use pm_stay_awake & pm_relax to avoid suspend sequence during
active playback

testing Done:
Music Playback ongoing
$ cat /sys/devices/soc.0/qcom,ara-codec.82/power/wakeup_active
1
Music Playback stopped
$ cat /sys/devices/soc.0/qcom,ara-codec.82/power/wakeup_active
0
Tested-by: David Lin <dtwlin@google.com>
Reviewed-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Akash Choudhari <akashtc@google.com>
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>

We really shouldn't be passing response structures around this way, but
since we now are, let's at least make sure not to break the 80 col
limit.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Errno -ENOSYS is reserved for missing syscalls, replace it with ENOMSG.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

All SVC error messages, except for a few recently added ones, place the
errno last after a colon (:). Let's at least try to be consistent
within the svc code.

Note that this format also allows for more concise messages without risk
for ambiguity.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This makes it more readable, as the functions are present in this order
in the structure as well. Also keeping these two makes more sense.

Tested by removing the gb-es2.ko module on both EVT1.5 and qemu with
gbsim.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

-ENOENT or -ESHUTDOWN happens when the urbs are being killed from
->disconnect() callback.  Don't complain to userspace about this, as the
user will see this on es2 module removal.

Tested by removing the gb-es2.ko module on both EVT1.5 and qemu with
gbsim. The driver doesn't throw anymore errors like:
"urb cport in error -2 (dropped)".
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: David Lin <dtwlin@google.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This allows greybus to do operations before being removed.

Tested by removing the gb-es2.ko module on both EVT1.5 and qemu with
gbsim. The driver removes the greybus host device successfully before
disabling the urbs. The errors are still coming ("urb cport in error -2
(dropped)"), but with an error value -2 (ENOENT) instead of -108. And
that happens while the urbs are disabled, not while doing greybus
operations.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: David Lin <dtwlin@google.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The usb core disables the Interface prior to calling ->disconnect() for
the usb driver. That disallows the es2 driver to remove the greybus host
device and every entity below it in a clean way, as the greybus core may
want to do few operations over the usb connection before getting
removed.

And so we see bunch of errors while we remove the es2 module, like:
"urb cport in error -108 (dropped)"

The usb core has a special per-driver flag, 'soft_unbind', for such usb
drivers. If this flag is set by a driver, the usb core doesn't disable
the Interface prior to calling ->disconnect().

Set that flag for es2.

Tested by removing the gb-es2.ko module on both EVT1.5 and qemu with
gbsim. The interface isn't disabled by the core and the driver is still
able initiate greybus operations over the Interface. This can be
properly tested only after the next patch which removes the greybus host
device before disabling the urbs.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This fixes below warnings ..

greybus/audio_codec.c:20:32: warning: symbol 'find_data' was not declared. Should it be static?
greybus/audio_codec.c:955:6: warning: symbol 'gbaudio_codec_cleanup' was not declared. Should it be static?
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

s/Firware/Firmware
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The number of CSI TX lanes is hardcoded to 4. Removing
this and start using value from configure stream response.

NOTE: The patch depends on the CSI init change:
"Use GB CSI params to init camera sub-devs"
Signed-off-by: Evgeniy Borisov <eborisov@mm-sol.com>
Reviewed-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This change adds the AP Power Monitor functions to
read out all the rails power information monitored by
the SVC.

Testing Done:
- $ cat /d/greybus/1-svc/pwrmon/*/*
  and validate the output with the svc stub power
  monitor functions
- $ tree /d/greybus/1-svc/pwrmon
  | | | |---pwrmon
  | | | | |---DUMMY_RAIL_1
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
  | | | | |---DUMMY_RAIL_2
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
  | | | | |---DUMMY_RAIL_3
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
  | | | | |---DUMMY_RAIL_4
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Read on apb_log causes null pointer exception due to the missing es2
device pointer passing to the debugfs.

Testing done:
- Enable apb_log and cat it
Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The check for line coding changed should use memcmp and not memcpy.

Testing done: trivial
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove unnecessary interface-remove helper.

Also add comment about why the disconnected flag is set.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Keep a detected interface registered until it is physically removed.
Specifically, do not re-register an interface that is switching mode.

Note that this also allows us to get rid of some nasty hacks from core.
The Ara VID/PID bootrom hack for ES2 will continue to work, but is now
mostly confined to the bootrom driver.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>