The TPIDRURO and TPIDRURW registers need to be flushed during exec;
otherwise TLS information is potentially leaked.  TPIDRURO in
particular needs careful treatment.  Since flush_thread basically
needs the same code used to set the TLS in arm_syscall, pull that into
a common set_tls helper in tls.h and use it in both places.

Similarly, TEEHBR needs to be cleared during exec as well.  Clearing
its save slot in thread_info isn't right as there is no guarantee
that a thread switch will occur before the new program runs.  Just
setting the register directly is sufficient.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Previous commits that dealt with get_user for 64bit type missed to
export proper functions, so if get_user macro with particular target/value
types are used by kernel module modpost would produce 'undefined!' error.
Solution is to export all required functions.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

e38361d0 'ARM: 8091/2: add get_user() support for 8 byte types' commit
broke V7 BE get_user call when target var size is 64 bit, but '*ptr' size
is 32 bit or smaller. e38361d0 changed type of __r2 from 'register
unsigned long' to 'register typeof(x) __r2 asm("r2")' i.e before the change
even when target variable size was 64 bit, __r2 was still 32 bit.
But after e38361d0 commit, for target var of 64 bit size, __r2 became 64
bit and now it should occupy 2 registers r2, and r3. The issue in BE case
that r3 register is least significant word of __r2 and r2 register is most
significant word of __r2. But __get_user_4 still copies result into r2 (most
significant word of __r2). Subsequent code copies from __r2 into x, but
for situation described it will pick up only garbage from r3 register.

Special __get_user_64t_(124) functions are introduced. They are similar to
corresponding __get_user_(124) function but result stored in r3 register
(lsw in case of 64 bit __r2 in BE image). Those function are used by
get_user macro in case of BE and target var size is 64bit.

Also changed __get_user_lo8 name into __get_user_32t_8 to get consistent
naming accross all cases.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

According to the ARM ARMv7, explicit barriers are necessary when using
synchronisation primitives such as SWP{B}. The use of these
instructions does not automatically imply a barrier and any ordering
requirements by the software must be explicitly expressed with the use
of suitable barriers.

Based on this, remove the barriers from SWP{B} emulation.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Since commit 1dbfa187 ("ARM: irq migration: force migration off CPU
going down") the ARM interrupt migration code on cpu offline calls
irqchip.irq_set_affinity() with the argument force=true. At the point
of this change the argument had no effect because it was not used by
any interrupt chip driver and there was no semantics defined.

This changed with commit 01f8fa4f ("genirq: Allow forcing cpu
affinity of interrupts") which made the force argument useful to route
interrupts to not yet online cpus without checking the target cpu
against the cpu online mask. The following commit ffde1de6
("irqchip: gic: Support forced affinity setting") implemented this for
the GIC interrupt controller.

As a consequence the ARM cpu offline irq migration fails if CPU0 is
offlined, because CPU0 is still set in the affinity mask and the
validataion against cpu online mask is skipped to the force argument
being true. The following first_cpu(mask) selection always selects
CPU0 as the target.

Solve the issue by calling irq_set_affinity() with force=false from
the CPU offline irq migration code so the GIC driver validates the
affinity mask against CPU online mask and therefore removes CPU0 from
the possible target candidates.

Tested on TC2 hotpluging CPU0 in and out. Without this patch the system
locks up as the IRQs are not migrated away from CPU0.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ARM: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSET

In commit 7fb00c2f ("ARM: 8114/1: LPAE:
load upper bits of early TTBR0/TTBR1") part which fixes carrying in adding
TTBR1_OFFSET to TTRR1 was wrong:

        addls   ttbr1, ttbr1, #TTBR1_OFFSET
        adcls   tmp, tmp, #0

addls doesn't update flags, adcls adds carry from cmp above:

        cmp     ttbr1, tmp                    @ PHYS_OFFSET > PAGE_OFFSET?

Condition 'ls' means carry flag is clear or zero flag is set, thus only one
case is affected: when PHYS_OFFSET == PAGE_OFFSET.

It seems safer to remove this fixup. Bug is here for ages and nobody
complained. Let's fix it separately.
Reported-and-Tested-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit af040ffc ("ARM: make it easier to check the CPU part number
correctly") changed ARM_CPU_PART_X masks, and the way they are returned and
checked against. Usage of read_cpuid_part_number() is now deprecated, and
calling places updated accordingly. This actually broke cpuidle-big_little
initialization, as bl_idle_driver_init() performs a check using an hardcoded
mask on cpu_id.

Create an interface to perform the check (that is now even easier to read).
Define also a proper mask (ARM_CPU_PART_MASK) that makes this kind of checks
cleaner and helps preventing bugs in the future. Update usage accordingly.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

On revisions of Cortex-A15 prior to r3p3, a CLREX instruction at PL1 may
falsely trigger a watchpoint exception, leading to potential data aborts
during exception return and/or livelock.

This patch resolves the issue in the following ways:

  - Replacing our uses of CLREX with a dummy STREX sequence instead (as
    we did for v6 CPUs).

  - Removing the clrex code from v7_exit_coherency_flush and derivatives,
    since this only exists as a minor performance improvement when
    non-cached exclusives are in use (Linux doesn't use these).

Benchmarking on a variety of ARM cores revealed no measurable
performance difference with this change applied, so the change is
performed unconditionally and no new Kconfig entry is added.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:

  - We clear the monitors on every exception return since commit
    200b812d ("Clear the exclusive monitor when returning from an
    exception"), so this is not necessary to ensure the monitors are
    cleared before returning from a fault handler.

  - Any dummy STREX will target a temporary scratch area in memory, and
    may succeed or fail without corrupting useful data. Its status value
    will not be used.

  - Any other STREX in the kernel must be preceded by an LDREX, which
    will initialise the monitors consistently and will not depend on the
    earlier state of the monitors.

Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.

This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Kernel module build with GCOV profiling fails to load with the
following error:

 $ insmod test_module.ko
   test_module: unknown relocation: 38
   insmod: can't insert 'test_module.ko': invalid module format

This happens because constructor pointers in the .init_array section
have not supported R_ARM_TARGET1 relocation type.

Documentation (ELF for the ARM Architecture) says:
    "The relocation must be processed either in the same way as R_ARM_REL32 or
     as R_ARM_ABS32: a virtual platform must specify which method is used."

Since kernel expects to see absolute addresses in .init_array R_ARM_TARGET1
relocation type should be treated the same way as R_ARM_ABS32.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull NFS client fixes from Trond Myklebust:
 "Highlights:

   - more fixes for read/write codepath regressions
     * sleeping while holding the inode lock
     * stricter enforcement of page contiguity when coalescing requests
     * fix up error handling in the page coalescing code

   - don't busy wait on SIGKILL in the file locking code"

* tag 'nfs-for-3.17-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
  nfs: can_coalesce_requests must enforce contiguity
  nfs: disallow duplicate pages in pgio page vectors
  nfs: don't sleep with inode lock in lock_and_join_requests
  nfs: fix error handling in lock_and_join_requests
  nfs: use blocking page_group_lock in add_request
  nfs: fix nonblocking calls to nfs_page_group_lock
  nfs: change nfs_page_group_lock argument

Merge tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas

Pull SH driver fix from Simon Horman:
 "Confine SH_INTC to platforms that need it"

* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  sh: intc: Confine SH_INTC to platforms that need it

Pull MIPS fixes from Ralf Baechle:
 "Pretty much all across the field so with this we should be in
  reasonable shape for the upcoming -rc2"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: OCTEON: make get_system_type() thread-safe
  MIPS: CPS: Initialize EVA before bringing up VPEs from secondary cores
  MIPS: Malta: EVA: Rename 'eva_entry' to 'platform_eva_init'
  MIPS: EVA: Add new EVA header
  MIPS: scall64-o32: Fix indirect syscall detection
  MIPS: syscall: Fix AUDIT value for O32 processes on MIPS64
  MIPS: Loongson: Fix COP2 usage for preemptible kernel
  MIPS: NL: Fix nlm_xlp_defconfig build error
  MIPS: Remove race window in page fault handling
  MIPS: Malta: Improve system memory detection for '{e, }memsize' >= 2G
  MIPS: Alchemy: Fix db1200 PSC clock enablement
  MIPS: BCM47XX: Fix reboot problem on BCM4705/BCM4785
  MIPS: Remove duplicated include from numa.c
  MIPS: Add common plat_irq_dispatch declaration
  MIPS: MSP71xx: remove unused plat_irq_dispatch() argument
  MIPS: GIC: Remove useless parens from GICBIS().
  MIPS: perf: Mark pmu interupt IRQF_NO_THREAD

Merge tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull fix for ftrace function tracer/profiler conflict from Steven Rostedt:
 "The rewrite of the ftrace code that makes it possible to allow for
  separate trampolines had a design flaw with the interaction between
  the function and function_graph tracers.

  The main flaw was the simplification of the use of multiple tracers
  having the same filter (like function and function_graph, that use the
  set_ftrace_filter file to filter their code).  The design assumed that
  the two tracers could never run simultaneously as only one tracer can
  be used at a time.  The problem with this assumption was that the
  function profiler could be implemented on top of the function graph
  tracer, and the function profiler could run at the same time as the
  function tracer.  This caused the assumption to be broken and when
  ftrace detected this failed assumpiton it would spit out a nasty
  warning and shut itself down.

  Instead of using a single ftrace_ops that switches between the
  function and function_graph callbacks, the two tracers can again use
  their own ftrace_ops.  But instead of having a complex hierarchy of
  ftrace_ops, the filter fields are placed in its own structure and the
  ftrace_ops can carefully use the same filter.  This change took a bit
  to be able to allow for this and currently only the global_ops can
  share the same filter, but this new design can easily be modified to
  allow for any ftrace_ops to share its filter with another ftrace_ops.

  The first four patches deal with the change of allowing the ftrace_ops
  to share the filter (and this needs to go to 3.16 as well).

  The fifth patch fixes a bug that was also caused by the new changes
  but only for archs other than x86, and only if those archs implement a
  direct call to the function_graph tracer which they do not do yet but
  will in the future.  It does not need to go to stable, but needs to be
  fixed before the other archs update their code to allow direct calls
  to the function_graph trampoline"

* tag 'trace-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Use current addr when converting to nop in __ftrace_replace_code()
  ftrace: Fix function_profiler and function tracer together
  ftrace: Fix up trampoline accounting with looping on hash ops
  ftrace: Update all ftrace_ops for a ftrace_hash_ops update
  ftrace: Allow ftrace_ops to use the hashes from other ops

Pull x86 fixes from Ingo Molnar:
 "A couple of EFI fixes, plus misc fixes all around the map"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/arm64: Store Runtime Services revision
  firmware: Do not use WARN_ON(!spin_is_locked())
  x86_32, entry: Clean up sysenter_badsys declaration
  x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
  x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
  x86/mm: Fix RCU splat from new TLB tracepoints

Pull perf fixes from Ingo Molnar:
 "A kprobes and a perf compat ioctl fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Handle compat ioctl
  kprobes: Skip kretprobe hit in NMI context to avoid deadlock

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes from this week, it's been pretty quiet and
  nothing really stands out as particularly noteworthy here -- mostly
  minor fixes across the field:

   - ODROID booting was fixed due to PMIC interrupts missing in DT
   - a collection of i.MX fixes
   - minor Tegra fix for regulators
   - Rockchip fix and addition of SoC-specific mailing list to make it
     easier to find posted patches"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  bus: arm-ccn: Fix warning message
  ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
  ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
  MAINTAINERS: add new Rockchip SoC list
  ARM: dts: rockchip: readd missing mmc0 pinctrl settings
  ARM: dts: ODROID i2c improvements
  ARM: dts: Enable PMIC interrupts on ODROID
  ARM: dts: imx6sx: fix the pad setting for uart CTS_B
  ARM: dts: i.MX53: fix apparent bug in VPU clks
  ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
  ARM: dts: imx6: edmqmx6: change enet reset pin
  ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
  ARM: imx: remove unnecessary ARCH_HAS_OPP select
  ARM: imx: fix TLB missing of IOMUXC base address during suspend
  ARM: imx6: fix SMP compilation again
  ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes

Pull gpio fixes from Linus Walleij:

 - a largeish fix for the IRQ handling in the new Zynq driver.  The
   quite verbose commit message gives the exact details.
 - move some defines for gpiod flags outside an ifdef to make stub
   functions work again.
 - various minor fixes that we can accept for -rc1.

* tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio-lynxpoint: enable input sensing in resume
  gpio: move GPIOD flags outside #ifdef
  gpio: delete unneeded test before of_node_put
  gpio: zynq: Fix IRQ handlers
  gpiolib: devres: use correct structure type name in sizeof
  MAINTAINERS: Change maintainer for gpio-bcm-kona.c

Pull drm fixes from Dave Airlie:
 "Intel and radeon fixes.

  Post KS/LC git requests from i915 and radeon stacked up.  They are all
  fixes along with some new pci ids for radeon, and one maintainers file
  entry.

   - i915: display fixes and irq fixes
   - radeon: pci ids, and misc gpuvm, dpm and hdp cache"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
  MAINTAINERS: Add entry for Renesas DRM drivers
  drm/radeon: add additional SI pci ids
  drm/radeon: add new bonaire pci ids
  drm/radeon: add new KV pci id
  Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
  drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
  drm/radeon: fix active cu count for SI and CIK
  drm/radeon: re-enable selective GPUVM flushing
  drm/radeon: Sync ME and PFP after CP semaphore waits v4
  drm/radeon: fix display handling in radeon_gpu_reset
  drm/radeon: fix pm handling in radeon_gpu_reset
  drm/radeon: Only flush HDP cache for indirect buffers from userspace
  drm/radeon: properly document reloc priority mask
  drm/i915: don't try to retrain a DP link on an inactive CRTC
  drm/i915: make sure VDD is turned off during system suspend
  drm/i915: cancel hotplug and dig_port work during suspend and unload
  drm/i915: fix HPD IRQ reenable work cancelation
  drm/i915: take display port power domain in DP HPD handler
  drm/i915: Don't try to enable cursor from setplane when crtc is disabled
  drm/i915: Skip load detect when intel_crtc->new_enable==true
  ...

As reported by Dan Aloni, commit f8567a38 ("aio: fix aio request
leak when events are reaped by userspace") introduces a regression when
user code attempts to perform io_submit() with more events than are
available in the ring buffer.  Reverting that commit would reintroduce a
regression when user space event reaping is used.

Fixing this bug is a bit more involved than the previous attempts to fix
this regression.  Since we do not have a single point at which we can
count events as being reaped by user space and io_getevents(), we have
to track event completion by looking at the number of events left in the
event ring.  So long as there are as many events in the ring buffer as
there have been completion events generate, we cannot call
put_reqs_available().  The code to check for this is now placed in
refill_reqs_available().

A test program from Dan and modified by me for verifying this bug is available
at http://www.kvack.org/~bcrl/20140824-aio_bug.c .
Reported-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Dan Aloni <dan@kernelim.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: stable@vger.kernel.org      # v3.16 and anything that f8567a38 was backported to
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A message warning a user about wrong vc value was printing
out port instead.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>

Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.

(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)

Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:

Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.

* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  MAINTAINERS: add new Rockchip SoC list
  ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: Olof Johansson <olof@lixom.net>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>

This pull just contains some new pci ids.

* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: add additional SI pci ids
  drm/radeon: add new bonaire pci ids
  drm/radeon: add new KV pci id

Add the new list that Rockchip-specific patches should also be directed to.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.

This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Merge tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Merge "Allwinner DT changes, take 2" from Maxime Ripard:

Only a single patch in here that fixes a DTC warning.

* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>

In __ftrace_replace_code(), when converting the call to a nop in a function
it needs to compare against the "curr" (current) value of the ftrace ops, and
not the "new" one. It currently does not affect x86 which is the only arch
to do the trampolines with function graph tracer, but when other archs that do
depend on this code implement the function graph trampoline, it can crash.

Here's an example when ARM uses the trampolines (in the future):

 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 9 at kernel/trace/ftrace.c:1716 ftrace_bug+0x17c/0x1f4()
 Modules linked in: omap_rng rng_core ipv6
 CPU: 0 PID: 9 Comm: migration/0 Not tainted 3.16.0-test-10959-gf0094b28-dirty #52
 [<c02188f4>] (unwind_backtrace) from [<c021343c>] (show_stack+0x20/0x24)
 [<c021343c>] (show_stack) from [<c095a674>] (dump_stack+0x78/0x94)
 [<c095a674>] (dump_stack) from [<c02532a0>] (warn_slowpath_common+0x7c/0x9c)
 [<c02532a0>] (warn_slowpath_common) from [<c02532ec>] (warn_slowpath_null+0x2c/0x34)
 [<c02532ec>] (warn_slowpath_null) from [<c02cbac4>] (ftrace_bug+0x17c/0x1f4)
 [<c02cbac4>] (ftrace_bug) from [<c02cc44c>] (ftrace_replace_code+0x80/0x9c)
 [<c02cc44c>] (ftrace_replace_code) from [<c02cc658>] (ftrace_modify_all_code+0xb8/0x164)
 [<c02cc658>] (ftrace_modify_all_code) from [<c02cc718>] (__ftrace_modify_code+0x14/0x1c)
 [<c02cc718>] (__ftrace_modify_code) from [<c02c7244>] (multi_cpu_stop+0xf4/0x134)
 [<c02c7244>] (multi_cpu_stop) from [<c02c6e90>] (cpu_stopper_thread+0x54/0x130)
 [<c02c6e90>] (cpu_stopper_thread) from [<c0271cd4>] (smpboot_thread_fn+0x1ac/0x1bc)
 [<c0271cd4>] (smpboot_thread_fn) from [<c026ddf0>] (kthread+0xe0/0xfc)
 [<c026ddf0>] (kthread) from [<c020f318>] (ret_from_fork+0x14/0x20)
 ---[ end trace dc9ce72c5b617d8f ]---
[   65.047264] ftrace failed to modify [<c0208580>] asm_do_IRQ+0x10/0x1c
[   65.054070]  actual: 85:1b:00:eb

Fixes: 7413af1f "ftrace: Make get_ftrace_addr() and get_ftrace_addr_old() global"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

The latest rewrite of ftrace removed the separate ftrace_ops of
the function tracer and the function graph tracer and had them
share the same ftrace_ops. This simplified the accounting by removing
the multiple layers of functions called, where the global_ops func
would call a special list that would iterate over the other ops that
were registered within it (like function and function graph), which
itself was registered to the ftrace ops list of all functions
currently active. If that sounds confusing, the code that implemented
it was also confusing and its removal is a good thing.

The problem with this change was that it assumed that the function
and function graph tracer can never be used at the same time.
This is mostly true, but there is an exception. That is when the
function profiler uses the function graph tracer to profile.
The function profiler can be activated the same time as the function
tracer, and this breaks the assumption and the result is that ftrace
will crash (it detects the error and shuts itself down, it does not
cause a kernel oops).

To solve this issue, a previous change allowed the hash tables
for the functions traced by a ftrace_ops to be a pointer and let
multiple ftrace_ops share the same hash. This allows the function
and function_graph tracer to have separate ftrace_ops, but still
share the hash, which is what is done.

Now the function and function graph tracers have separate ftrace_ops
again, and the function tracer can be run while the function_profile
is active.

Cc: stable@vger.kernel.org # 3.16 (apply after 3.17-rc4 is out)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

If a SIGKILL is sent to a task waiting in __nfs_iocounter_wait,
it will busy-wait or soft lockup in its while loop.
nfs_wait_bit_killable won't sleep, and the loop won't exit on
the error return.

Stop the busy-wait by breaking out of the loop when
nfs_wait_bit_killable returns an error.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

Commit 6094f838
"nfs: allow coalescing of subpage requests" got rid of the requirement
that requests cover whole pages, but it made some incorrect assumptions.

It turns out that callers of this interface can map adjacent requests
(by file position as seen by req_offset + req->wb_bytes) to different pages,
even when they could share a page. An example is the direct I/O interface -
iov_iter_get_pages_alloc may return one segment with a partial page filled
and the next segment (which is adjacent in the file position) starts with a
new page.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

Adjacent requests that share the same page are allowed, but should only
use one entry in the page vector. This avoids overruning the page
vector - it is sized based on how many bytes there are, not by
request count.

This fixes issues that manifest as "Redzone overwritten" bugs (the
vector overrun) and hangs waiting on page read / write, as it waits on
the same page more than once.

This also adds bounds checking to the page vector with a graceful failure
(WARN_ON_ONCE and pgio error returned to application).
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

This handles the 'nonblock=false' case in nfs_lock_and_join_requests.
If the group is already locked and blocking is allowed, drop the inode lock
and wait for the group lock to be cleared before trying it all again.
This should fix warnings found in peterz's tree (sched/wait branch), where
might_sleep() checks are added to wait.[ch].
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

This fixes handling of errors from nfs_page_group_lock in
nfs_lock_and_join_requests.  It now releases the inode lock and the
reference to the head request.
Reported-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

__nfs_pageio_add_request was calling nfs_page_group_lock nonblocking, but
this can return -EAGAIN which would end up passing -EIO to the application.

There is no reason not to block in this path, so change the two calls to
do so. Also, there is no need to check the return value of
nfs_page_group_lock when nonblock=false, so remove the error handling code.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

nfs_page_group_lock was calling wait_on_bit_lock even when told not to
block. Fix by first trying test_and_set_bit, followed by wait_on_bit_lock
if and only if blocking is allowed.  Return -EAGAIN if nonblocking and the
test_and_set of the bit was already locked.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

Flip the meaning of the second argument from 'wait' to 'nonblock' to
match related functions. Update all five calls to reflect this change.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>