of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

As the widget PM may turn off the pins, this might lead to the silent
output for beep when no explicit paths are given.  This patch adds
fake output paths for the beep widget so that the output pins are
dynamically powered upon beep on/off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

VIA codecs used to have the own power controls but they were disabled
at transition to the generic parser due to the coding assuming the
fixed routes.  Now we get the proper support of equivalently fine
power management in the generic parser, and the old kludges can be
replaced with it.  This results in the reduction of lots of dead
codes.

The advanced PM feature is disabled as default like before for keeping
the compatible behavior.  It's enabled via "Dynamic Power-Control"
mixer element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch enables the finer power state control of each widget
depending on the jack plug state and streaming state in addition to
the existing power_down_unused power optimization.  The new feature is
enabled only when codec->power_mgmt flag is set.

Two new flags, pin_enabled and stream_enabled, are introduced in
nid_path struct for marking the two individual power states: the pin
plug/unplug and DAC/ADC stream, respectively.  They can be set
statically in case they are static routes (e.g. some mixer paths),
too.

The power up and down events for each pin are triggered via the
standard hda_jack table.  The call order is hard-coded, relying on the
current implementation of jack event chain (a la FILO/stack order).

One point to be dealt carefully is that DAC/ADC cannot be powered
on/off while streaming.  They are pinned as long as the stream is
running.  For controlling the power of DAC/ADC, a new patch_ops is
added.  The generic parser provides the default callback for that.

As of this patch, only IDT/Sigmatel codec driver enables the flag.
The support on other codecs will follow.

An assumption we made in this code is that the widget state (e.g. amp,
pinctl, connections) remains after the widget power transition (not
about FG power transition).  This is true for IDT codecs, at least.
But if the widget state is lost at widget power transition, we'd need
to implement additional code to sync the cached amp/verbs for the
specific NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add sampling rate control for ADC/DAC for ESI W192M.
Allow to switch between 48K/96K/192K sampling rate.
All DAC need to be mute when changing samplerate.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add text Line in/Mic for selecting input gain state in mixer for ESI W192M.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add TLV support to control volume using dB scale for input and ouput on ESI W192M.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Enable midi i/o port of envy24 chip as their are available on ESI W192M soundcard.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Update eeprom structure to C99 standard to be compliant with change in alsa.
It's just a notation change, no configuration change.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Correct copy/paste name from prodigy driver, no behaviour change, only name.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch does two things:
- code refactoring with a local helper function,
- allow codec drivers to provide the specific PCM stream info pointers
  only for overriding the non-NULL entries, instead of copying the
  whole.

This simplifies the codec driver side (currently the only user is
alc269's 44kHz fixed rate).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The commit [ef403edb: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input.  In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").

This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull drm fix from Dave Airlie:
 "An oops snuck in in an -rc3 patch, this fixes it"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  [PATCH] drm/mm: Fix support 4 GiB and larger ranges

Pull clock framework fixes from Michael Turquette:
 "The clk fixes for 4.0-rc4 comprise three themes.

  First are the usual driver fixes for new regressions since v3.19.

  Second are fixes to the common clock divider type caused by recent
  changes to how we round clock rates.  This affects many clock drivers
  that use this common code.

  Finally there are fixes for drivers that improperly compared struct
  clk pointers (drivers must not deref these pointers).  While some of
  these drivers have done this for a long time, this did not cause a
  problem until we started generating unique struct clk pointers for
  every consumer.  A new function, clk_is_match was introduced to get
  these drivers working again and they are fixed up to no longer deref
  the pointers themselves"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  ASoC: kirkwood: fix struct clk pointer comparing
  ASoC: fsl_spdif: fix struct clk pointer comparing
  ARM: imx: fix struct clk pointer comparing
  clk: introduce clk_is_match
  clk: don't export static symbol
  clk: divider: fix calculation of initial best divider when rounding to closest
  clk: divider: fix selection of divider when rounding to closest
  clk: divider: fix calculation of maximal parent rate for a given divider
  clk: divider: return real rate instead of divider value
  clk: qcom: fix platform_no_drv_owner.cocci warnings
  clk: qcom: fix platform_no_drv_owner.cocci warnings
  clk: qcom: Add PLL4 vote clock
  clk: qcom: lcc-msm8960: Fix PLL rate detection
  clk: qcom: Fix slimbus n and m val offsets
  clk: ti: Fix FAPLL parent enable bit handling

bad argument if(tmp)... in check_free_hole

fix oops: kernel BUG at drivers/gpu/drm/drm_mm.c:305!

[airlied: excellent, this was my task for today].
Signed-off-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a rather unpleasantly large set of bug fixes for arm-soc, Most
  of them because of cross-tree dependencies for Exynos where we should
  have figured out the right path to merge things before the merge
  window, and then the maintainer being unable to sort things out in
  time during a business trip.

  The other changes contained here are the usual collection:

  MAINTAINERS file updates
   - Gregory Clement is now a co-maintainer for the legacy Marvell EBU
     platforms
   - A MAINTAINERS entry for the Freescale Vybrid platform that was
     added last year
   - Matt Porter no longer works as a maintainer on Broadcom SoCs

  Build-time issues
   - A compile-time error for at91
   - Several minor DT fixes on at91, imx, exynos, socfpga, and omap
   - The new digicolor platform was not correctly enabled at all

  Configuration issues
   - Two defconfig fix for regressions using USB on versatile express
     and on OMAP3
   - Enabling all 8 CPUs on Allwinner/SUNxi
   - Enabling the new STiH410 platform to be usable

  Bug fixes in platform code
   - A missing barrier for socfpga
   - Fixing LPDDR1 self-refresh mode on at91
   - Fixing RTC interrupt numbers on Exynos3250
   - Fixing a cache-coherency issues in CPU power-down on Exynos5
   - Multiple small OMAP power management fixes"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (69 commits)
  MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
  ARM: at91: pm_slowclock: fix the compilation error
  ARM: at91/dt: fix USB high-speed clock to select UTMI
  ARM: at91/dt: fix at91 udc compatible strings
  ARM: at91/dt: declare matrix node as a syscon device
  ARM: vexpress: update CONFIG_USB_ISP1760 option
  ARM: digicolor: add the machine directory to Makefile
  ARM: STi: Add STiH410 SoC support
  MAINTAINERS: add Freescale Vybrid SoC
  MAINTAINERS: Remove self as ARM mach-bcm co-maintainer
  ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
  ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
  ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
  ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
  ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
  ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
  ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
  ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
  ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
  ARM: dts: OMAP5: fix polling intervals for thermal zones
  ...

Pull irqchip fixes from Jason Cooper:
 "armada-370-xp:
   - Chained per-cpu interrupts

  gic{,-v3,v3-its}"
   - Various fixes for safer operation"

* tag 'irqchip-fixes-4.0' of git://git.infradead.org/users/jcooper/linux:
  irqchip: gicv3-its: Support safe initialization
  irqchip: gicv3-its: Define macros for GITS_CTLR fields
  irqchip: gicv3-its: Add limitation to page order
  irqchip: gicv3-its: Use 64KB page as default granule
  irqchip: gicv3-its: Zero itt before handling to hardware
  irqchip: gic-v3: Fix out of bounds access to cpu_logical_map
  irqchip: gic: Fix unsafe locking reported by lockdep
  irqchip: gicv3-its: Fix unsafe locking reported by lockdep
  irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration
  irqchip: gicv3-its: Allocate enough memory for the full range of DeviceID
  irqchip: gicv3-its: Fix ITS CPU init
  irqchip: armada-370-xp: Fix chained per-cpu interrupts

Pull drm fixes from Dave Airlie:
 "Misc i915, vmwgfx and radeon fixes along with a fix for one of those
  recursive sleep mutex debug cases in the mst code"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix an issue with the device losing its irq line on module unload
  drm/vmwgfx: Correctly NULLify dma buffer pointer on failure
  drm/vmwgfx: Reorder device takedown somewhat
  drm/vmwgfx: Fix a couple of lock dependency violations
  drm/radeon: drop setting UPLL to sleep mode
  drm/radeon: fix wait to actually occur after the signaling callback
  drm/i915: Prevent TLB error on first execution on SNB
  drm/i915: Do both mt and gen6 style forcewake reset on ivb probe
  drm/i915: Make WAIT_IOCTL negative timeouts be indefinite again
  drm/i915: use in_interrupt() not in_irq() to check context
  drm/mst: fix recursive sleep warning on qlock
  drm: Don't assign fbs for universal cursor support to files

Pull SCSI fix from James Bottomley:
 "This is a simple fix for a domain revalidation crash which has
  recently turned up in the libsas code (applies to mvsas, isc and
  aic94xx)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  libsas: Fix Kernel Crash in smp_execute_task

Pull file locking bugfix from Jeff Layton:
 "Just a small fix for a potential problem in one of the lease
  tracepoints"

* tag 'locks-v4.0-4' of git://git.samba.org/jlayton/linux:
  locks: fix generic_delete_lease tracepoint to use victim pointer

Pull VFIO fix from Alex Williamson:
 "Add missing break to avoid clobbering ioctl (Alexey Kardashevskiy)"

* tag 'vfio-v4.0-rc4' of git://github.com/awilliam/linux-vfio:
  vfio-pci: Add missing break to enable VFIO_PCI_ERR_IRQ_INDEX

Pull arm64 fixes from Catalin Marinas:

 - add TLB invalidation for page table tear-down which was missed when
   support for CONFIG_HAVE_RCU_TABLE_FREE was added (assuming page table
   freeing was always deferred)

 - use UEFI for system and reset poweroff if available

 - fix asm label placement in relation to the alignment statement

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: put __boot_cpu_mode label after alignment instead of before
  efi/arm64: use UEFI for system reset and poweroff
  arm64: Invalidate the TLB corresponding to intermediate page table levels

Merge tag 'linux-kselftest-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fix from Shuah Khan:
 "selftests/exec: Check if the syscall exists and bail if not"

* tag 'linux-kselftest-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/exec: Check if the syscall exists and bail if not

It's possible that "fl" won't point at a valid lock at this point, so
use "victim" instead which is either a valid lock or NULL.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>

Another one for the big head.S spring cleaning: the label should
be after the .align or it may point to the padding.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

If UEFI Runtime Services are available, they are preferred over direct
PSCI calls or other methods to reset the system.

For the reset case, we need to hook into machine_restart(), as the
arm_pm_restart function pointer may be overwritten by modules.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ARM architecture allows the caching of intermediate page table
levels and page table freeing requires a sequence like:

	pmd_clear()
	TLB invalidation
	pte page freeing

With commit 5e5f6dc1 (arm64: mm: enable HAVE_RCU_TABLE_FREE logic),
the page table freeing batching was moved from tlb_remove_page() to
tlb_remove_table(). The former takes care of TLB invalidation as this is
also shared with pte clearing and page cache page freeing. The latter,
however, does not invalidate the TLBs for intermediate page table levels
as it probably relies on the architecture code to do it if required.
When the mm->mm_users < 2, tlb_remove_table() does not do any batching
and page table pages are freed before tlb_finish_mmu() which performs
the actual TLB invalidation.

This patch introduces __tlb_flush_pgtable() for arm64 and calls it from
the {pte,pmd,pud}_free_tlb() directly without relying on deferred page
table freeing.

Fixes: 5e5f6dc1 arm64: mm: enable HAVE_RCU_TABLE_FREE logic
Reported-by: Jon Masters <jcm@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull power management and ACPI fixes from Rafael Wysocki:
 "Just two fixes, one for an ACPI LPSS driver issue introduced during
  the 3.17 cycle and one revert of a recent commit that sort of broke
  the cpupower tool.

  Specifics:

   - Fix an ACPI LPSS (Low-Power Subsystem) driver issue causing the
     8250_dw driver to confuse an LPSS clock with another one it is
     supposed to handle due to the lack of identification allowing it to
     tell those clocks apart (Heikki Krogerus).

   - Revert a recent commit that was supposed to improve the usability
     of the cpupower tool, but clearly did the opposite (Josh Boyer)"

* tag 'pm+acpi-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "cpupower Makefile change to help run the tool without 'make install'"
  ACPI / LPSS: provide con_id for the clkdev

I will also take care of the legacy support(not fully converted to DT)
of the mvebu SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* pm-tools:
  Revert "cpupower Makefile change to help run the tool without 'make install'"

Pull xen bug fixes from David Vrabel:

 - fix a PV regression in 3.19.

 - fix a dom0 crash on hosts with large numbers of PIRQs.

 - prevent pcifront from disabling memory or I/O port access, which may
   trigger host crashes.

* tag 'stable/for-linus-4.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen-pciback: limit guest control of command register
  xen/events: avoid NULL pointer dereference in dom0 on large machines
  xen: Remove trailing semicolon from xenbus_register_frontend() definition
  x86/xen: correct bug in p2m list initialization

Pull sound fixes from Takashi Iwai:
 "This is a round of HD-audio fixes: there are a long-standing
  regression fix and a few more device/codec-specific quirks.

  In addition, a couple of FireWire regression fixes, a USB-audio quirk
  for Roland UA-22 and a sanity check in API for user-defined control
  elements"

* tag 'sound-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Don't access stereo amps for mono channel widgets
  ALSA: hda - Add workaround for MacBook Air 5,2 built-in mic
  ALSA: hda - Set single_adc_amp flag for CS420x codecs
  ALSA: snd-usb: add quirks for Roland UA-22
  ALSA: control: Add sanity checks for user ctl id name string
  ALSA: hda - Fix built-in mic on Compaq Presario CQ60
  ALSA: firewire-lib: leave unit reference counting completely
  Revert "ALSA: dice: fix wrong offsets for Dice interface"
  ALSA: hda - Fix regression of HD-audio controller fallback modes

Pull DeviceTree fixes from Rob Herring:

 - fix for stdout-path option parsing with added unittest

 - fix for stdout-path interaction with earlycon

 - several DT unittest fixes

 - fix Sparc allmodconfig build error on of_platform_register_reconfig_notifier

 - several DT overlay kconfig and build warning fixes

 - several DT binding documentation updates

* tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of/platform: Fix sparc:allmodconfig build
  of: unittest: Add options string testcase variants
  of: fix handling of '/' in options for of_find_node_by_path()
  of/unittest: Fix the wrong expected value in of_selftest_property_string
  of/unittest: remove the duplicate of_changeset_init
  dt: submitting-patches: clarify that DT maintainers are to be cced on bindings
  of: unittest: fix I2C dependency
  of/overlay: Remove unused variable
  Documentation: DT: Renamed of-serial.txt to 8250.txt
  of: Fix premature bootconsole disable with 'stdout-path'
  serial: add device tree binding documentation for ETRAX FS UART
  of/overlay: Directly include idr.h
  of: Drop superfluous dependance for OF_OVERLAY
  of: Add vendor prefix for Arasan
  of: Add prompt for OF_OVERLAY config

Pull gadgetfs fixes from Al Viro:
 "Assorted fixes around AIO on gadgetfs: leaks, use-after-free, troubles
  caused by ->f_op flipping"

* 'gadget' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  gadgetfs: really get rid of switching ->f_op
  gadgetfs: get rid of flipping ->f_op in ep_config()
  gadget: switch ep_io_operations to ->read_iter/->write_iter
  gadgetfs: use-after-free in ->aio_read()
  gadget/function/f_fs.c: switch to ->{read,write}_iter()
  gadget/function/f_fs.c: use put iov_iter into io_data
  gadget/function/f_fs.c: close leaks
  move iov_iter.c from mm/ to lib/
  new helper: dup_iter()