- 18 Mar, 2015 19 commits
-
-
Kristina Martšenko authored
commit 89bb35e2 upstream. Using the touchscreen while running buffered capture results in the buffer reporting lots of wrong values, often just zeros. This is because we push readings to the buffer every time a touchscreen interrupt arrives, including when the buffer's own conversions have not yet finished. So let's only push to the buffer when its conversions are ready. Signed-off-by:
Kristina Martšenko <kristina.martsenko@gmail.com> Reviewed-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Kristina Martšenko authored
commit 6abe0300 upstream. Reading a channel through sysfs, or starting a buffered capture, can occasionally turn off the touchscreen. This is because the read_raw() and buffer preenable()/postdisable() callbacks unschedule current conversions on all channels. If a delay channel happens to schedule a touchscreen conversion at the same time, the conversion gets cancelled and the touchscreen sequence stops. This is probably related to this note from the reference manual: "If a delay group schedules channels to be sampled and a manual write to the schedule field in CTRL0 occurs while the block is discarding samples, the LRADC will switch to the new schedule and will not sample the channels that were previously scheduled. The time window for this to happen is very small and lasts only while the LRADC is discarding samples." So make the callbacks only unschedule conversions for the channels they use. This means channel 0 for read_raw() and channels 0-5 for the buffer (if the touchscreen is enabled). Since the touchscreen uses different channels (6 and 7), it no longer gets turned off. This is tested and fixes the issue on i.MX28, but hasn't been tested on i.MX23. Signed-off-by:
-
Kristina Martšenko authored
commit 86bf7f3e upstream. Reading a channel through sysfs, or starting a buffered capture, will currently turn off the touchscreen. This is because the read_raw() and buffer preenable()/postdisable() callbacks disable interrupts for all LRADC channels, including those the touchscreen uses. So make the callbacks only disable interrupts for the channels they use. This means channel 0 for read_raw() and channels 0-5 for the buffer (if the touchscreen is enabled). Since the touchscreen uses different channels (6 and 7), it no longer gets turned off. Note that only i.MX28 is affected by this issue, i.MX23 should be fine. Signed-off-by:
-
Kristina Martšenko authored
commit f81197b8 upstream. The touchscreen was initially designed [1] to map all of its physical channels to one virtual channel, leaving buffered capture to use the remaining 7 virtual channels. When the touchscreen was reimplemented [2], it was made to use four virtual channels, which overlap and conflict with the channels the buffer uses. As a result, when the buffer is enabled, the touchscreen's virtual channels are remapped to whichever physical channels the buffer was configured with, causing the touchscreen to read those instead of the touch measurement channels. Effectively the touchscreen stops working. So here we separate the channels again, giving the touchscreen 2 virtual channels and the buffer 6. We can't give the touchscreen just 1 channel as before, as the current pressure calculation requires 2 channels to be read at the same time. This makes the touchscreen continue to work during buffered capture. It has been tested on i.MX28, but not on i.MX23. [1] 06ddd353 ("iio: mxs: Implement support for touchscreen") [2] dee05308 ("Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection") Signed-off-by:
-
Ryusuke Konishi authored
commit 957ed60b upstream. Each inode of nilfs2 stores a root node of a b-tree, and it turned out to have a memory overrun issue: Each b-tree node of nilfs2 stores a set of key-value pairs and the number of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as a few other "bn_*" members. Since the value of "bn_nchildren" is used for operations on the key-values within the b-tree node, it can cause memory access overrun if a large number is incorrectly set to "bn_nchildren". For instance, nilfs_btree_node_lookup() function determines the range of binary search with it, and too large "bn_nchildren" leads nilfs_btree_node_get_key() in that function to overrun. As for intermediate b-tree nodes, this is prevented by a sanity check performed when each node is read from a drive, however, no sanity check has been done for root nodes stored in inodes. This patch fixes the issue by adding missing sanity check against b-tree root nodes so that it's called when on-memory inodes are read from ifile, inode metadata file. Signed-off-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Catalin Marinas authored
commit 9d42d48a upstream. The native (64-bit) sigval_t union contains sival_int (32-bit) and sival_ptr (64-bit). When a compat application invokes a syscall that takes a sigval_t value (as part of a larger structure, e.g. compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t union is converted to the native sigval_t with sival_int overlapping with either the least or the most significant half of sival_ptr, depending on endianness. When the corresponding signal is delivered to a compat application, on big endian the current (compat_uptr_t)sival_ptr cast always returns 0 since sival_int corresponds to the top part of sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int is copied to the compat_siginfo_t structure. Reported-by:
Bamvor Jian Zhang <bamvor.zhangjian@huawei.com> Tested-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Alex Deucher authored
commit dbfb00c3 upstream. The logic was reversed from what the hw actually exposed. Fixes graphics corruption in certain harvest configurations. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 3d2d98ee upstream. Just in case it hasn't been calculated for the mode. Signed-off-by:
-
Takashi Iwai authored
commit de5d0ad5 upstream. This is essentially a partial revert of the commit [b1920c21: 'ALSA: hda - Enable runtime PM on Panther Point']. There was a bug report showing the HD-audio bus hang during runtime PM on HP Spectre XT. Reported-by:
Dang Sananikone <dang.sananikone@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Tomáš Hodek authored
commit d1901ef0 upstream. When a drive is marked write-mostly it should only be the target of reads if there is no other option. This behaviour was broken by commit 9dedf603 md/raid1: read balance chooses idlest disk for SSD which causes a write-mostly device to be *preferred* is some cases. Restore correct behaviour by checking and setting best_dist_disk and best_pending_disk rather than best_disk. We only need to test one of these as they are both changed from -1 or >=0 at the same time. As we leave min_pending and best_dist unchanged, any non-write-mostly device will appear better than the write-mostly device. Reported-by:
Tomáš Hodek <tomas.hodek@volny.cz> Reported-by:
Dark Penguin <darkpenguin@yandex.ru> Signed-off-by:
NeilBrown <neilb@suse.de> Link: http://marc.info/?l=linux-raid&m=135982797322422 Fixes: 9dedf603Signed-off-by:
-
Chris Wilson authored
commit 6c31a614 upstream. When we walk the list of vma, or even for protecting against concurrent framebuffer creation, we must hold the struct_mutex or else a second thread can corrupt the list as we walk it. Fixes regression from commit d7f46fc4 Author: Ben Widawsky <benjamin.widawsky@intel.com> Date: Fri Dec 6 14:10:55 2013 -0800 drm/i915: Make pin count per VMA References: https://bugs.freedesktop.org/show_bug.cgi?id=89085Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Jaroslav Kysela authored
commit 37ed3988 upstream. It is a bad idea to export static functions. GCC for some platforms shows errors like: error: __ksymtab_azx_get_response causes a section type conflict Signed-off-by:
Jaroslav Kysela <perex@perex.cz> Signed-off-by:
-
James Hogan authored
commit c2996cb2 upstream. The KSTK_EIP() and KSTK_ESP() macros should return the user program counter (PC) and stack pointer (A0StP) of the given task. These are used to determine which VMA corresponds to the user stack in /proc/<pid>/maps, and for the user PC & A0StP in /proc/<pid>/stat. However for Meta the PC & A0StP from the task's kernel context are used, resulting in broken output. For example in following /proc/<pid>/maps output, the 3afff000-3b021000 VMA should be described as the stack: # cat /proc/self/maps ... 100b0000-100b1000 rwxp 00000000 00:00 0 [heap] 3afff000-3b021000 rwxp 00000000 00:00 0 And in the following /proc/<pid>/stat output, the PC is in kernel code (1074234964 = 0x40078654) and the A0StP is in the kernel heap (1335981392 = 0x4fa17550): # cat /proc/self/stat 51 (cat) R ... 1335981392 1074234964 ... Fix the definitions of KSTK_EIP() and KSTK_ESP() to use task_pt_regs(tsk)->ctx rather than (tsk)->thread.kernel_context. This gets the registers from the user context stored after the thread info at the base of the kernel stack, which is from the last entry into the kernel from userland, regardless of where in the kernel the task may have been interrupted, which results in the following more correct /proc/<pid>/maps output: # cat /proc/self/maps ... 0800b000-08070000 r-xp 00000000 00:02 207 /lib/libuClibc-0.9.34-git.so ... 100b0000-100b1000 rwxp 00000000 00:00 0 [heap] 3afff000-3b021000 rwxp 00000000 00:00 0 [stack] And /proc/<pid>/stat now correctly reports the PC in libuClibc (134320308 = 0x80190b4) and the A0StP in the [stack] region (989864576 = 0x3b002280): # cat /proc/self/stat 51 (cat) R ... 989864576 134320308 ... Reported-by:
Alexey Brodkin <Alexey.Brodkin@synopsys.com> Reported-by:
Vineet Gupta <Vineet.Gupta1@synopsys.com> Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Signed-off-by:
-
Takashi Iwai authored
commit 70372a75 upstream. When a PCM draining is performed to an empty stream that has been already in PREPARED state, the current code just ignores and leaves as it is, although the drain is supposed to set all such streams to SETUP state. This patch covers that overlooked case. Signed-off-by:
-
Nicolas Saenz Julienne authored
commit 2f97c20e upstream. The gpio_chip operations receive a pointer the gpio_chip struct which is contained in the driver's private struct, yet the container_of call in those functions point to the mfd struct defined in include/linux/mfd/tps65912.h. Signed-off-by:
Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Hans Holmberg authored
commit 9cf75e9e upstream. The change: 7b8792bb gpiolib: of: Correct error handling in of_get_named_gpiod_flags assumed that only one gpio-chip is registred per of-node. Some drivers register more than one chip per of-node, so adjust the matching function of_gpiochip_find_and_xlate to not stop looking for chips if a node-match is found and the translation fails. Fixes: 7b8792bb ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags") Signed-off-by:
Hans Holmberg <hans.holmberg@intel.com> Acked-by:
Alexandre Courbot <acourbot@nvidia.com> Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Tested-by:
Tyler Hall <tylerwhall@gmail.com> Signed-off-by:
-
Jani Nikula authored
commit cf6f0af9 upstream. Add quirk for Dell Chromebook 11 backlight. Reported-and-tested-by:
Owen Garland <garland.owen@gmail.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93451Acked-by:
Damien Lespiau <damien.lespiau@intel.com> Signed-off-by:
-
Jan Kara authored
commit dfcc70a8 upstream. For filesystems without separate project quota inode field in the superblock we just reuse project quota file for group quotas (and vice versa) if project quota file is allocated and we need group quota file. When we reuse the file, quota structures on disk suddenly have wrong type stored in d_flags though. Nobody really cares about this (although structure type reported to userspace was wrong as well) except that after commit 14bf61ff (quota: Switch ->get_dqblk() and ->set_dqblk() to use bytes as space units) assertion in xfs_qm_scall_getquota() started to trigger on xfs/106 test (apparently I was testing without XFS_DEBUG so I didn't notice when submitting the above commit). Fix the problem by properly resetting ddq->d_flags when running quotacheck for a quota file. Reported-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
Jan Kara <jack@suse.cz> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Takashi Iwai authored
commit 6426460e upstream. BIOS doesn't seem to set up pins for 5.1 and the SPDIF out, so we need to give explicitly here. Reported-and-tested-by:
Misan Thropos <misanthropos@gmx.de> Signed-off-by:
-
- 12 Mar, 2015 21 commits
-
-
Jiri Pirko authored
commit 9215f437 upstream. Currently the list is traversed using rcu variant. That is not correct since dev_set_mac_address can be called which eventually calls rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this by remove the rcu usage here. Fixes: 3d249d4c "net: introduce ethernet teaming device" Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Lorenzo Colitti authored
commit 9145736d upstream. 1. For an IPv4 ping socket, ping_check_bind_addr does not check the family of the socket address that's passed in. Instead, make it behave like inet_bind, which enforces either that the address family is AF_INET, or that the family is AF_UNSPEC and the address is 0.0.0.0. 2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL if the socket family is not AF_INET6. Return EAFNOSUPPORT instead, for consistency with inet6_bind. 3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT instead of EINVAL if an incorrect socket address structure is passed in. 4. Make IPv6 ping sockets be IPv6-only. The code does not support IPv4, and it cannot easily be made to support IPv4 because the protocol numbers for ICMP and ICMPv6 are different. This makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead of making the socket unusable. Among other things, this fixes an oops that can be triggered by: int s = socket(AF_INET, SOCK_DGRAM, IPPROTO_ICMP); struct sockaddr_in6 sin6 = { .sin6_family = AF_INET6, .sin6_addr = in6addr_any, }; bind(s, (struct sockaddr *) &sin6, sizeof(sin6)); Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241 Signed-off-by:
Lorenzo Colitti <lorenzo@google.com> Signed-off-by:
-
Michal Kubeček authored
commit acf8dd0a upstream. If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer checksum is to be computed on segmentation. However, in this case, skb->csum_start and skb->csum_offset are never set as raw socket transmit path bypasses udp_send_skb() where they are usually set. As a result, driver may access invalid memory when trying to calculate the checksum and store the result (as observed in virtio_net driver). Moreover, the very idea of modifying the userspace provided UDP header is IMHO against raw socket semantics (I wasn't able to find a document clearly stating this or the opposite, though). And while allowing CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit too intrusive change just to handle a corner case like this. Therefore disallowing UFO for packets from SOCK_DGRAM seems to be the best option. Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Ben Shelton authored
commit 42c972a1 upstream. The National Instruments USB Host-to-Host Cable is based on the Prolific PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it. Signed-off-by:
Ben Shelton <ben.shelton@ni.com> Signed-off-by:
-
Eric Dumazet authored
commit 2f1d8b9e upstream. Brian reported crashes using IPv6 traffic with macvtap/veth combo. I tracked the crashes in neigh_hh_output() -> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD); Neighbour code assumes headroom to push Ethernet header is at least 16 bytes. It appears macvtap has only 14 bytes available on arches where NET_IP_ALIGN is 0 (like x86) Effect is a corruption of 2 bytes right before skb->head, and possible crashes if accessing non existing memory. This fix should also increase IPv4 performance, as paranoid code in ip_finish_output2() wont have to call skb_realloc_headroom() Reported-by:
Brian Rak <brak@vultr.com> Tested-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Catalin Marinas authored
commit d720d8ce upstream. With commit a7526eb5 (net: Unbreak compat_sys_{send,recv}msg), the MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points, changing the kernel compat behaviour from the one before the commit it was trying to fix (1be374a0, net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg). On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native 32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by the kernel). However, on a 64-bit kernel, the compat ABI is different with commit a7526eb5. This patch changes the compat_sys_{send,recv}msg behaviour to the one prior to commit 1be374a0. The problem was found running 32-bit LTP (sendmsg01) binary on an arm64 kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg() but the general rule is not to break user ABI (even when the user behaviour is not entirely sane). Fixes: a7526eb5 (net: Unbreak compat_sys_{send,recv}msg) Cc: Andy Lutomirski <luto@amacapital.net> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jiri Pirko authored
commit 57e59563 upstream. Currently following race is possible in team: CPU0 CPU1 team_port_del team_upper_dev_unlink priv_flags &= ~IFF_TEAM_PORT team_handle_frame team_port_get_rcu team_port_exists priv_flags & IFF_TEAM_PORT == 0 return NULL (instead of port got from rx_handler_data) netdev_rx_handler_unregister The thing is that the flag is removed before rx_handler is unregistered. If team_handle_frame is called in between, team_port_exists returns 0 and team_port_get_rcu will return NULL. So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister that team_handle_frame will always see valid rx_handler_data pointer. Signed-off-by:
-
Matthew Thode authored
commit a4176a93 upstream. colons are used as a separator in netdev device lookup in dev_ioctl.c Specific functions are SIOCGIFTXQLEN SIOCETHTOOL SIOCSIFNAME Signed-off-by:
Matthew Thode <mthode@mthode.org> Signed-off-by:
-
Pravin B Shelar authored
commit 7b4577a9 upstream. Open vSwitch allows moving internal vport to different namespace while still connected to the bridge. But when namespace deleted OVS does not detach these vports, that results in dangling pointer to netdevice which causes kernel panic as follows. This issue is fixed by detaching all ovs ports from the deleted namespace at net-exit. BUG: unable to handle kernel NULL pointer dereference at 0000000000000028 IP: [<ffffffffa0aadaa5>] ovs_vport_locate+0x35/0x80 [openvswitch] Oops: 0000 [#1] SMP Call Trace: [<ffffffffa0aa6391>] lookup_vport+0x21/0xd0 [openvswitch] [<ffffffffa0aa65f9>] ovs_vport_cmd_get+0x59/0xf0 [openvswitch] [<ffffffff8167e07c>] genl_family_rcv_msg+0x1bc/0x3e0 [<ffffffff8167e319>] genl_rcv_msg+0x79/0xc0 [<ffffffff8167d919>] netlink_rcv_skb+0xb9/0xe0 [<ffffffff8167deac>] genl_rcv+0x2c/0x40 [<ffffffff8167cffd>] netlink_unicast+0x12d/0x1c0 [<ffffffff8167d3da>] netlink_sendmsg+0x34a/0x6b0 [<ffffffff8162e140>] sock_sendmsg+0xa0/0xe0 [<ffffffff8162e5e8>] ___sys_sendmsg+0x408/0x420 [<ffffffff8162f541>] __sys_sendmsg+0x51/0x90 [<ffffffff8162f592>] SyS_sendmsg+0x12/0x20 [<ffffffff81764ee9>] system_call_fastpath+0x12/0x17 Reported-by:
Assaf Muller <amuller@redhat.com> Fixes: 46df7b81("openvswitch: Add support for network namespaces.") Signed-off-by:
Pravin B Shelar <pshelar@nicira.com> Reviewed-by:
Thomas Graf <tgraf@noironetworks.com> Signed-off-by:
-
Ignacy Gawędzki authored
commit 34eea79e upstream. In tcf_em_validate(), after calling request_module() to load the kind-specific module, set em->ops to NULL before returning -EAGAIN, so that module_put() is not called again by tcf_em_tree_destroy(). Signed-off-by:
Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr> Acked-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
-
Guenter Roeck authored
commit 54da5a8b upstream. phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex) to find a valid entry in the settings array for the given speed and duplex value. For full duplex 1000baseT, this will return the first matching entry, which is the entry for 1000baseKX_Full. If the phy eee does not support 1000baseKX_Full, this entry will not match, causing phy_init_eee to fail for no good reason. Fixes: 9a9c56cb ("net: phy: fix a bug when verify the EEE support") Fixes: 3e707706 ("phy: Expand phy speed/duplex settings array") Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Alexander Drozdov authored
commit 3e32e733 upstream. ip_check_defrag() may be used by af_packet to defragment outgoing packets. skb_network_offset() of af_packet's outgoing packets is not zero. Signed-off-by:
Alexander Drozdov <al.drozdov@gmail.com> Signed-off-by:
-
Alexander Drozdov authored
commit fba04a9e upstream. skb_copy_bits() returns zero on success and negative value on error, so it is needed to invert the condition in ip_check_defrag(). Fixes: 1bf3751e ("ipv4: ip_check_defrag must not modify skb before unsharing") Signed-off-by:
-
Ignacy Gawędzki authored
commit 1c4cff0c upstream. The gnet_stats_copy_app() function gets called, more often than not, with its second argument a pointer to an automatic variable in the caller's stack. Therefore, to avoid copying garbage afterwards when calling gnet_stats_finish_copy(), this data is better copied to a dynamically allocated memory that gets freed after use. [xiyou.wangcong@gmail.com: remove a useless kfree()] Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
WANG Cong authored
commit 7afb8886 upstream. Ignacy reported that when eth0 is down and add a vlan device on top of it like: ip link add link eth0 name eth0.1 up type vlan id 1 We will get a refcount leak: unregister_netdevice: waiting for eth0.1 to become free. Usage count = 2 The problem is when rtnl_configure_link() fails in rtnl_newlink(), we simply call unregister_device(), but for stacked device like vlan, we almost do nothing when we unregister the upper device, more work is done when we unregister the lower device, so call its ->dellink(). Reported-by:
-
Martin KaFai Lau authored
commit 3b471175 upstream. ipv6_cow_metrics() currently assumes only DST_HOST routes require dynamic metrics allocation from inetpeer. The assumption breaks when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric. Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set() is called after the route is created. This patch creates the metrics array (by calling dst_cow_metrics_generic) in ipv6_cow_metrics(). Test: radvd.conf: interface qemubr0 { AdvLinkMTU 1300; AdvCurHopLimit 30; prefix fd00:face:face:face::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; }; Before: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec fe80::/64 dev eth0 proto kernel metric 256 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec After: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec mtu 1300 fe80::/64 dev eth0 proto kernel metric 256 mtu 1300 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec mtu 1300 hoplimit 30 Fixes: 8e2ec639 (ipv6: don't use inetpeer to store metrics for routes.) Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
-
Eric Dumazet authored
commit ba34e6d9 upstream. IPv6 can keep a copy of SYN message using skb_get() in tcp_v6_conn_request() so that caller wont free the skb when calling kfree_skb() later. Therefore TCP fast open has to clone the skb it is queuing in child->sk_receive_queue, as all skbs consumed from receive_queue are freed using __kfree_skb() (ie assuming skb->users == 1) Signed-off-by:
Yuchung Cheng <ycheng@google.com> Fixes: 5b7ed089 ("tcp: move fastopen functions to tcp_fastopen.c") Signed-off-by:
-
Daniel Borkmann authored
commit 364d5716 upstream. ifla_vf_policy[] is wrong in advertising its individual member types as NLA_BINARY since .type = NLA_BINARY in combination with .len declares the len member as *max* attribute length [0, len]. The issue is that when do_setvfinfo() is being called to set up a VF through ndo handler, we could set corrupted data if the attribute length is less than the size of the related structure itself. The intent is exactly the opposite, namely to make sure to pass at least data of minimum size of len. Fixes: ebc08a6f ("rtnetlink: Add VF config code to rtnetlink") Cc: Mitch Williams <mitch.a.williams@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Sabrina Dubroca authored
commit 7744b5f3 upstream. This patch fixes two issues in UDP checksum computation in pktgen. First, the pseudo-header uses the source and destination IP addresses. Currently, the ports are used for IPv4. Second, the UDP checksum covers both header and data. So we need to generate the data earlier (move pktgen_finalize_skb up), and compute the checksum for UDP header + data. Fixes: c26bf4a5 ("pktgen: Add UDPCSUM flag to support UDP checksums") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
-
Miroslav Urbanek authored
commit 233c96fc upstream. flow_cache_flush_task references a structure member flow_cache_gc_work where it should reference flow_cache_flush_task instead. Kernel panic occurs on kernels using IPsec during XFRM garbage collection. The garbage collection interval can be shortened using the following sysctl settings: net.ipv4.xfrm4_gc_thresh=4 net.ipv6.xfrm6_gc_thresh=4 With the default settings, our productions servers crash approximately once a week. With the settings above, they crash immediately. Fixes: ca925cf1 ("flowcache: Make flow cache name space aware") Reported-by:
Tomáš Charvát <tc@excello.cz> Tested-by:
Jan Hejl <jh@excello.cz> Signed-off-by:
Miroslav Urbanek <mu@miroslavurbanek.com> Acked-by:
-
Julian Anastasov authored
commit 528c943f upstream. ip_vs_conn_fill_param_sync() gets in param.pe a module reference for persistence engine from __ip_vs_pe_getbyname() but forgets to put it. Problem occurs in backup for sync protocol v1 (2.6.39). Also, pe_data usually comes in sync messages for connection templates and ip_vs_conn_new() copies the pointer only in this case. Make sure pe_data is not leaked if it comes unexpectedly for normal connections. Leak can happen only if bogus messages are sent to backup server. Fixes: fe5e7a1e ("IPVS: Backup, Adding Version 1 receive capability") Signed-off-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
