- 11 Mar, 2021 5 commits
-
-
Andre Guedes authored
The comment describing the timestamps layout in the packet buffer is wrong and the code is actually retrieving the timestamp in Timer 1 reference instead of Timer 0. This hasn't been a big issue so far because hardware is configured to report both timestamps using Timer 0 (see IGC_SRRCTL register configuration in igc_ptp_enable_rx_timestamp() helper). This patch fixes the comment and the code so we retrieve the timestamp in Timer 0 reference as expected. This patch also takes the opportunity to get rid of the hw.mac.type check since it is not required. Fixes: 81b05520 ("igc: Add support for RX timestamping") Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Signed-off-by:
Vedang Patel <vedang.patel@intel.com> Signed-off-by:
Jithu Joseph <jithu.joseph@intel.com> Reviewed-by:
Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by:
Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Muhammad Husaini Zulkifli authored
The Supported Pause Frame always display "No" even though the Advertised pause frame showing the correct setting based on the pause parameters via ethtool. Set bit in link_ksettings to "Supported" for Pause Frame. Before output: Supported pause frame use: No Expected output: Supported pause frame use: Symmetric Fixes: 8c5ad0da ("igc: Add ethtool support") Signed-off-by:
Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Reviewed-by:
Malli C <mallikarjuna.chilakala@intel.com> Tested-by:
Sasha Neftin <sasha.neftin@intel.com> Signed-off-by:
-
Muhammad Husaini Zulkifli authored
Fix Pause Frame Advertising when getting the advertisement via ethtool. Remove setting the "advertising" bit in link_ksettings during default case when Tx and Rx are in off state with Auto Negotiate off. Below is the original output of advertisement link during Tx and Rx off: Advertised pause frame use: Symmetric Receive-only Expected output: Advertised pause frame use: No Fixes: 8c5ad0da ("igc: Add ethtool support") Signed-off-by:
-
Sasha Neftin authored
This commit applies to the igc_reset_task the same changes that were applied to the igb driver in commit 024a8168 ("igb: reinit_locked() should be called with rtnl_lock") and fix possible race in reset subtask. Fixes: 0507ef8a ("igc: Add transmit and receive fastpath and interrupt handlers") Suggested-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Florian Fainelli authored
Similar to commit 92696286 ("net: bcmgenet: Set phydev->dev_flags only for internal PHYs") we need to qualify the phydev->dev_flags based on whether the port is connected to an internal or external PHY otherwise we risk having a flags collision with a completely different interpretation depending on the driver. Fixes: aa9aef77 ("net: dsa: bcm_sf2: communicate integrated PHY revision to PHY driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 10 Mar, 2021 35 commits
-
-
Florian Fainelli authored
The bcm_sf2 driver uses the b53 driver as a library but does not make usre of the b53_setup() function, this made it fail to inherit the vlan_filtering_is_global attribute. Fix this by moving the assignment to b53_switch_alloc() which is used by bcm_sf2. Fixes: 7228b23e ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings") Signed-off-by:
-
Eric Dumazet authored
iproute2 package is well behaved, but malicious user space can provide illegal shift values and trigger UBSAN reports. Add stab parameter to red_check_params() to validate user input. syzbot reported: UBSAN: shift-out-of-bounds in ./include/net/red.h:312:18 shift exponent 111 is too large for 64-bit type 'long unsigned int' CPU: 1 PID: 14662 Comm: syz-executor.3 Not tainted 5.12.0-rc2-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:79 [inline] dump_stack+0x141/0x1d7 lib/dump_stack.c:120 ubsan_epilogue+0xb/0x5a lib/ubsan.c:148 __ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:327 red_calc_qavg_from_idle_time include/net/red.h:312 [inline] red_calc_qavg include/net/red.h:353 [inline] choke_enqueue.cold+0x18/0x3dd net/sched/sch_choke.c:221 __dev_xmit_skb net/core/dev.c:3837 [inline] __dev_queue_xmit+0x1943/0x2e00 net/core/dev.c:4150 neigh_hh_output include/net/neighbour.h:499 [inline] neigh_output include/net/neighbour.h:508 [inline] ip6_finish_output2+0x911/0x1700 net/ipv6/ip6_output.c:117 __ip6_finish_output net/ipv6/ip6_output.c:182 [inline] __ip6_finish_output+0x4c1/0xe10 net/ipv6/ip6_output.c:161 ip6_finish_output+0x35/0x200 net/ipv6/ip6_output.c:192 NF_HOOK_COND include/linux/netfilter.h:290 [inline] ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:215 dst_output include/net/dst.h:448 [inline] NF_HOOK include/linux/netfilter.h:301 [inline] NF_HOOK include/linux/netfilter.h:295 [inline] ip6_xmit+0x127e/0x1eb0 net/ipv6/ip6_output.c:320 inet6_csk_xmit+0x358/0x630 net/ipv6/inet6_connection_sock.c:135 dccp_transmit_skb+0x973/0x12c0 net/dccp/output.c:138 dccp_send_reset+0x21b/0x2b0 net/dccp/output.c:535 dccp_finish_passive_close net/dccp/proto.c:123 [inline] dccp_finish_passive_close+0xed/0x140 net/dccp/proto.c:118 dccp_terminate_connection net/dccp/proto.c:958 [inline] dccp_close+0xb3c/0xe60 net/dccp/proto.c:1028 inet_release+0x12e/0x280 net/ipv4/af_inet.c:431 inet6_release+0x4c/0x70 net/ipv6/af_inet6.c:478 __sock_release+0xcd/0x280 net/socket.c:599 sock_close+0x18/0x20 net/socket.c:1258 __fput+0x288/0x920 fs/file_table.c:280 task_work_run+0xdd/0x1a0 kernel/task_work.c:140 tracehook_notify_resume include/linux/tracehook.h:189 [inline] Fixes: 8afa10cb ("net_sched: red: Avoid illegal values") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
mlx5-fixes-2021-03-10 Signed-off-by: -
Rafał Miłecki authored
BCM4908 uses 2 Gbps link between switch and the Ethernet interface. Without this BCM4908 devices were able to achieve only 2 x ~895 Mb/s. This allows handling e.g. NAT traffic with 940 Mb/s. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Acked-by:
-
Pavel Andrianov authored
pxa168_eth_remove() firstly calls unregister_netdev(), then cancels a timeout work. unregister_netdev() shuts down a device interface and removes it from the kernel tables. If the timeout occurs in parallel, the timeout work (pxa168_eth_tx_timeout_task) performs stop and open of the device. It may lead to an inconsistent state and memory leaks. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Pavel Andrianov <andrianov@ispras.ru> Signed-off-by:
-
Eric Dumazet authored
macvlan_count_rx() can be called from process context, it is thus necessary to disable preemption before calling u64_stats_update_begin() syzbot was able to spot this on 32bit arch: WARNING: CPU: 1 PID: 4632 at include/linux/seqlock.h:271 __seqprop_assert include/linux/seqlock.h:271 [inline] WARNING: CPU: 1 PID: 4632 at include/linux/seqlock.h:271 __seqprop_assert.constprop.0+0xf0/0x11c include/linux/seqlock.h:269 Modules linked in: Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 4632 Comm: kworker/1:3 Not tainted 5.12.0-rc2-syzkaller #0 Hardware name: ARM-Versatile Express Workqueue: events macvlan_process_broadcast Backtrace: [<82740468>] (dump_backtrace) from [<827406dc>] (show_stack+0x18/0x1c arch/arm/kernel/traps.c:252) r7:00000080 r6:60000093 r5:00000000 r4:8422a3c4 [<827406c4>] (show_stack) from [<82751b58>] (__dump_stack lib/dump_stack.c:79 [inline]) [<827406c4>] (show_stack) from [<82751b58>] (dump_stack+0xb8/0xe8 lib/dump_stack.c:120) [<82751aa0>] (dump_stack) from [<82741270>] (panic+0x130/0x378 kernel/panic.c:231) r7:830209b4 r6:84069ea4 r5:00000000 r4:844350d0 [<82741140>] (panic) from [<80244924>] (__warn+0xb0/0x164 kernel/panic.c:605) r3:8404ec8c r2:00000000 r1:00000000 r0:830209b4 r7:0000010f [<80244874>] (__warn) from [<82741520>] (warn_slowpath_fmt+0x68/0xd4 kernel/panic.c:628) r7:81363f70 r6:0000010f r5:83018e50 r4:00000000 [<827414bc>] (warn_slowpath_fmt) from [<81363f70>] (__seqprop_assert include/linux/seqlock.h:271 [inline]) [<827414bc>] (warn_slowpath_fmt) from [<81363f70>] (__seqprop_assert.constprop.0+0xf0/0x11c include/linux/seqlock.h:269) r8:5a109000 r7:0000000f r6:a568dac0 r5:89802300 r4:00000001 [<81363e80>] (__seqprop_assert.constprop.0) from [<81364af0>] (u64_stats_update_begin include/linux/u64_stats_sync.h:128 [inline]) [<81363e80>] (__seqprop_assert.constprop.0) from [<81364af0>] (macvlan_count_rx include/linux/if_macvlan.h:47 [inline]) [<81363e80>] (__seqprop_assert.constprop.0) from [<81364af0>] (macvlan_broadcast+0x154/0x26c drivers/net/macvlan.c:291) r5:89802300 r4:8a927740 [<8136499c>] (macvlan_broadcast) from [<81365020>] (macvlan_process_broadcast+0x258/0x2d0 drivers/net/macvlan.c:317) r10:81364f78 r9:8a86d000 r8:8a9c7e7c r7:8413aa5c r6:00000000 r5:00000000 r4:89802840 [<81364dc8>] (macvlan_process_broadcast) from [<802696a4>] (process_one_work+0x2d4/0x998 kernel/workqueue.c:2275) r10:00000008 r9:8404ec98 r8:84367a02 r7:ddfe6400 r6:ddfe2d40 r5:898dac80 r4:8a86d43c [<802693d0>] (process_one_work) from [<80269dcc>] (worker_thread+0x64/0x54c kernel/workqueue.c:2421) r10:00000008 r9:8a9c6000 r8:84006d00 r7:ddfe2d78 r6:898dac94 r5:ddfe2d40 r4:898dac80 [<80269d68>] (worker_thread) from [<80271f40>] (kthread+0x184/0x1a4 kernel/kthread.c:292) r10:85247e64 r9:898dac80 r8:80269d68 r7:00000000 r6:8a9c6000 r5:89a2ee40 r4:8a97bd00 [<80271dbc>] (kthread) from [<80200114>] (ret_from_fork+0x14/0x20 arch/arm/kernel/entry-common.S:158) Exception stack(0x8a9c7fb0 to 0x8a9c7ff8) Fixes: 412ca155 ("macvlan: Move broadcasts into a work queue") Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Ido Schimmel authored
In the rare case that drop_monitor fails to register its probe on the 'napi_poll' tracepoint, it will not deactivate its hysteresis timer as part of the error path. If the hysteresis timer was armed by the shortly lived 'kfree_skb' probe and user space retries to initiate tracing, a warning will be emitted for trying to initialize an active object [1]. Fix this by properly undoing all the operations that were done prior to probe registration, in both software and hardware code paths. Note that syzkaller managed to fail probe registration by injecting a slab allocation failure [2]. [1] ODEBUG: init active (active state 0) object type: timer_list hint: sched_send_work+0x0/0x60 include/linux/list.h:135 WARNING: CPU: 1 PID: 8649 at lib/debugobjects.c:505 debug_print_object+0x16e/0x250 lib/debugobjects.c:505 Modules linked in: CPU: 1 PID: 8649 Comm: syz-executor.0 Not tainted 5.11.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:debug_print_object+0x16e/0x250 lib/debugobjects.c:505 [...] Call Trace: __debug_object_init+0x524/0xd10 lib/debugobjects.c:588 debug_timer_init kernel/time/timer.c:722 [inline] debug_init kernel/time/timer.c:770 [inline] init_timer_key+0x2d/0x340 kernel/time/timer.c:814 net_dm_trace_on_set net/core/drop_monitor.c:1111 [inline] set_all_monitor_traces net/core/drop_monitor.c:1188 [inline] net_dm_monitor_start net/core/drop_monitor.c:1295 [inline] net_dm_cmd_trace+0x720/0x1220 net/core/drop_monitor.c:1339 genl_family_rcv_msg_doit+0x228/0x320 net/netlink/genetlink.c:739 genl_family_rcv_msg net/netlink/genetlink.c:783 [inline] genl_rcv_msg+0x328/0x580 net/netlink/genetlink.c:800 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502 genl_rcv+0x24/0x40 net/netlink/genetlink.c:811 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline] netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:672 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2348 ___sys_sendmsg+0xf3/0x170 net/socket.c:2402 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2435 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xae [2] FAULT_INJECTION: forcing a failure. name failslab, interval 1, probability 0, space 0, times 1 CPU: 1 PID: 8645 Comm: syz-executor.0 Not tainted 5.11.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: dump_stack+0xfa/0x151 should_fail.cold+0x5/0xa should_failslab+0x5/0x10 __kmalloc+0x72/0x3f0 tracepoint_add_func+0x378/0x990 tracepoint_probe_register+0x9c/0xe0 net_dm_cmd_trace+0x7fc/0x1220 genl_family_rcv_msg_doit+0x228/0x320 genl_rcv_msg+0x328/0x580 netlink_rcv_skb+0x153/0x420 genl_rcv+0x24/0x40 netlink_unicast+0x533/0x7d0 netlink_sendmsg+0x856/0xd90 sock_sendmsg+0xcf/0x120 ____sys_sendmsg+0x6e8/0x810 ___sys_sendmsg+0xf3/0x170 __sys_sendmsg+0xe5/0x1b0 do_syscall_64+0x2d/0x70 entry_SYSCALL_64_after_hwframe+0x44/0xae Fixes: 70c69274 ("drop_monitor: Initialize timer and work item upon tracing enable") Fixes: 8ee2267a ("drop_monitor: Convert to using devlink tracepoint") Reported-by: syzbot+779559d6503f3a56213d@syzkaller.appspotmail.com Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Daniel Borkmann says: ==================== pull-request: bpf 2021-03-10 The following pull-request contains BPF updates for your *net* tree. We've added 8 non-merge commits during the last 5 day(s) which contain a total of 11 files changed, 136 insertions(+), 17 deletions(-). The main changes are: 1) Reject bogus use of vmlinux BTF as map/prog creation BTF, from Alexei Starovoitov. 2) Fix allocation failure splat in x86 JIT for large progs. Also fix overwriting percpu cgroup storage from tracing programs when nested, from Yonghong Song. 3) Fix rx queue retrieval in XDP for multi-queue veth, from Maciej Fijalkowski. 4) Fix bpf_check_mtu() helper API before freeze to have mtu_len as custom skb/xdp L3 input length, from Jesper Dangaard Brouer. 5) Fix inode_storage's lookup_elem return value upon having bad fd, from Tal Lossos. 6) Fix bpftool and libbpf cross-build on MacOS, from Georgi Valkov. ==================== Signed-off-by: -
Wei Wang authored
Syzbot reported the suspecious RCU usage in nexthop_fib6_nh() when called from ipv6_route_seq_show(). The reason is ipv6_route_seq_start() calls rcu_read_lock_bh(), while nexthop_fib6_nh() calls rcu_dereference_rtnl(). The fix proposed is to add a variant of nexthop_fib6_nh() to use rcu_dereference_bh_rtnl() for ipv6_route_seq_show(). The reported trace is as follows: ./include/net/nexthop.h:416 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 2 locks held by syz-executor.0/17895: at: seq_read+0x71/0x12a0 fs/seq_file.c:169 at: seq_file_net include/linux/seq_file_net.h:19 [inline] at: ipv6_route_seq_start+0xaf/0x300 net/ipv6/ip6_fib.c:2616 stack backtrace: CPU: 1 PID: 17895 Comm: syz-executor.0 Not tainted 4.15.0-syzkaller #0 Call Trace: [<ffffffff849edf9e>] __dump_stack lib/dump_stack.c:17 [inline] [<ffffffff849edf9e>] dump_stack+0xd8/0x147 lib/dump_stack.c:53 [<ffffffff8480b7fa>] lockdep_rcu_suspicious+0x153/0x15d kernel/locking/lockdep.c:5745 [<ffffffff8459ada6>] nexthop_fib6_nh include/net/nexthop.h:416 [inline] [<ffffffff8459ada6>] ipv6_route_native_seq_show net/ipv6/ip6_fib.c:2488 [inline] [<ffffffff8459ada6>] ipv6_route_seq_show+0x436/0x7a0 net/ipv6/ip6_fib.c:2673 [<ffffffff81c556df>] seq_read+0xccf/0x12a0 fs/seq_file.c:276 [<ffffffff81dbc62c>] proc_reg_read+0x10c/0x1d0 fs/proc/inode.c:231 [<ffffffff81bc28ae>] do_loop_readv_writev fs/read_write.c:714 [inline] [<ffffffff81bc28ae>] do_loop_readv_writev fs/read_write.c:701 [inline] [<ffffffff81bc28ae>] do_iter_read+0x49e/0x660 fs/read_write.c:935 [<ffffffff81bc81ab>] vfs_readv+0xfb/0x170 fs/read_write.c:997 [<ffffffff81c88847>] kernel_readv fs/splice.c:361 [inline] [<ffffffff81c88847>] default_file_splice_read+0x487/0x9c0 fs/splice.c:416 [<ffffffff81c86189>] do_splice_to+0x129/0x190 fs/splice.c:879 [<ffffffff81c86f66>] splice_direct_to_actor+0x256/0x890 fs/splice.c:951 [<ffffffff81c8777d>] do_splice_direct+0x1dd/0x2b0 fs/splice.c:1060 [<ffffffff81bc4747>] do_sendfile+0x597/0xce0 fs/read_write.c:1459 [<ffffffff81bca205>] SYSC_sendfile64 fs/read_write.c:1520 [inline] [<ffffffff81bca205>] SyS_sendfile64+0x155/0x170 fs/read_write.c:1506 [<ffffffff81015fcf>] do_syscall_64+0x1ff/0x310 arch/x86/entry/common.c:305 [<ffffffff84a00076>] entry_SYSCALL_64_after_hwframe+0x42/0xb7 Fixes: f88d8ea6 ("ipv6: Plumb support for nexthop object in a fib6_info") Reported-by:Wei Wang <weiwan@google.com> Cc: David Ahern <dsahern@kernel.org> Cc: Ido Schimmel <idosch@idosch.org> Cc: Petr Machata <petrm@nvidia.com> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
David S. Miller authored
Daniel Borkmann says: ==================== Fix ip6ip6 crash for collect_md skbs Fix a NULL pointer deref panic I ran into for regular ip6ip6 tunnel devices when collect_md populated skbs were redirected to them for xmit. See patches for further details, thanks! ==================== Signed-off-by: -
Daniel Borkmann authored
I ran into a crash where setting up a ip6ip6 tunnel device which was /not/ set to collect_md mode was receiving collect_md populated skbs for xmit. The BPF prog was populating the skb via bpf_skb_set_tunnel_key() which is assigning special metadata dst entry and then redirecting the skb to the device, taking ip6_tnl_start_xmit() -> ipxip6_tnl_xmit() -> ip6_tnl_xmit() and in the latter it performs a neigh lookup based on skb_dst(skb) where we trigger a NULL pointer dereference on dst->ops->neigh_lookup() since the md_dst_ops do not populate neigh_lookup callback with a fake handler. Transform the md_dst_ops into generic dst_blackhole_ops that can also be reused elsewhere when needed, and use them for the metadata dst entries as callback ops. Also, remove the dst_md_discard{,_out}() ops and rely on dst_discard{,_out}() from dst_init() which free the skb the same way modulo the splat. Given we will be able to recover just fine from there, avoid any potential splats iff this gets ever triggered in future (or worse, panic on warns when set). Fixes: f38a9eb1 ("dst: Metadata destinations") Signed-off-by:Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Daniel Borkmann authored
Move generic blackhole dst ops to the core and use them from both ipv4_dst_blackhole_ops and ip6_dst_blackhole_ops where possible. No functional change otherwise. We need these also in other locations and having to define them over and over again is not great. Signed-off-by:
-
Yevgeny Kliteynik authored
Fix 32-bit variable shift wrapping in dr_ste_v1_get_miss_addr. Fixes: a6098129 ("net/mlx5: DR, Add STEv1 setters and getters") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Yevgeny Kliteynik <kliteyn@nvidia.com> Reviewed-by:
Alex Vesker <valex@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Shay Drory authored
When SF id is unavailable, code jumps to wrong label that accesses sw id array outside of its range. Hence, when SF id is not allocated, avoid accessing such array. Fixes: 8f010541 ("net/mlx5: SF, Add port add delete functionality") Signed-off-by:
Shay Drory <shayd@nvidia.com> Reviewed-by:
Parav Pandit <parav@nvidia.com> Signed-off-by:
-
Shay Drory authored
Cited patch in the fixes tag missed to free the allocated work. Fix it by freeing the work after work execution. Fixes: f3196bb0 ("net/mlx5: Introduce vhca state event notifier") Signed-off-by:
-
Parav Pandit authored
Fix vhca context size as defined by device interface specification. Fixes: f3196bb0 ("net/mlx5: Introduce vhca state event notifier") Signed-off-by:
-
Parav Pandit authored
do_div() returns reminder, while cited patch wanted to use quotient. Fix it by using quotient. Fixes: 0e22bfb7 ("net/mlx5e: E-switch, Fix rate calculation for overflow") Signed-off-by:
Maor Dickman <maord@nvidia.com> Signed-off-by:
-
Maor Gottlieb authored
1. Don't set the ts_format bit to default when it reserved - device is running in the old mode (free running). 2. XRC doesn't have a CQ therefore the ts format in the QP context should be default / free running. 3. Set ts_format to WQ. Fixes: 2fe8d4b8 ("RDMA/mlx5: Fail QP creation if the device can not support the CQE TS") Signed-off-by:
Maor Gottlieb <maorg@nvidia.com> Signed-off-by:
-
Maor Gottlieb authored
QPs which don't care from timestamp mode, should set the ts_format to default, otherwise the QP creation could be failed if the timestamp mode is not supported. Fixes: 2fe8d4b8 ("RDMA/mlx5: Fail QP creation if the device can not support the CQE TS") Signed-off-by:
-
Roi Dayan authored
Move priv memset from init to cleanup to avoid double priv cleanup that can happen on profile change if also roolback fails. Add missing cleanup flow in mlx5e_netdev_attach_profile(). Fixes: c4d7eb57 ("net/mxl5e: Add change profile method") Signed-off-by:
Roi Dayan <roid@nvidia.com> Signed-off-by:
-
Maor Dickman authored
VF tunnel TX traffic offload is adding flow which forward to flow tables with lower level, which isn't support on all FW versions and may cause firmware to fail with syndrome. Fixed by enabling VF tunnel TX offload only if flow table capability ignore_flow_level is enabled. Fixes: 10742efc ("net/mlx5e: VF tunnel TX traffic offloading") Signed-off-by:
Vlad Buslov <vladbu@nvidia.com> Signed-off-by:
-
Roi Dayan authored
flow_attr->ip_version has the matching that should be done inner/outer. When working with chains, decapsulation is done on chain0 and next chain match on outer header which is the original inner which could be ipv4. So in tunnel route resolution we cannot use that to know which ip version we are at so save tun_ip_version when parsing the tunnel match and use that. Fixes: a508728a ("net/mlx5e: VF tunnel RX traffic offloading") Signed-off-by:
Dmytro Linkin <dlinkin@nvidia.com> Signed-off-by:
-
Aya Levin authored
Fix a bug of uninitialized pin index when trying to turn off PPS out. Fixes: de19cd6c ("net/mlx5: Move some PPS logic into helper functions") Signed-off-by:
Aya Levin <ayal@nvidia.com> Reviewed-by:
Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by:
-
Maor Dickman authored
The cited change added offload support for Geneve options without verifying the validity of the options masks, this caused offload of rules with match on Geneve options with class,type and data masks which are zero to fail. Fix by ignoring the match on Geneve options in case option masks are all zero. Fixes: 9272e3df ("net/mlx5e: Geneve, Add support for encap/decap flows offload") Signed-off-by:
Oz Shlomo <ozsh@nvidia.com> Reviewed-by:
-
Maxim Mikityanskiy authored
Port timestamping for PTP can be enabled/disabled while the channels are closed. In that case mlx5e_safe_switch_channels is skipped, and the preactivate hook is called directly. However, if that hook returns an error, the channel parameters must be reverted back to their old values. This commit adds missing handling on this case. Fixes: 145e5637 ("net/mlx5e: Add TX PTP port object support") Signed-off-by:
Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
-
Maxim Mikityanskiy authored
Each RQ (including XSK RQs) takes a reference to the XDP program. When an XDP program is attached or detached, the channels and queues are recreated, however, there is a special flow for changing an active XDP program to another one. In that flow, channels and queues stay alive, but the refcounts of the old and new XDP programs are adjusted. This flow didn't increment refcount by the number of active XSK RQs, and this commit fixes it. Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support") Signed-off-by:
-
Aya Levin authored
When closing the PTP channel, set its pointer explicitly to NULL. PTP channel is opened on demand, the code verify the pointer validity before access. Nullify it when closing the PTP channel to avoid unexpected behavior. Fixes: 145e5637 ("net/mlx5e: Add TX PTP port object support") Signed-off-by:
-
Aya Levin authored
In addition to .get_ethtool_stats, add port PTP TX stats to .ndo_get_stats64. Fixes: 145e5637 ("net/mlx5e: Add TX PTP port object support") Signed-off-by:
-
Tariq Toukan authored
Since cited patch, MLX5E_REQUIRED_WQE_MTTS is not a power of two. Hence, usage of MLX5E_LOG_ALIGNED_MPWQE_PPW should be replaced, as it lost some accuracy. Use the designated macro to calculate the number of required MTTs. This makes sure the solution in cited patch works properly. While here, un-inline mlx5e_get_mpwqe_offset(), and remove the unused RQ parameter. Fixes: c3c94023 ("net/mlx5e: Add resiliency in Striding RQ mode for packets larger than MTU") Signed-off-by:
-
Tariq Toukan authored
The ICOSQ size should not go below MLX5E_PARAMS_MINIMUM_LOG_SQ_SIZE. Enforce this where it's missing. Signed-off-by:
-
git://git.kernel.org:/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix transmissions in dynamic SMPS mode in ath9k, from Felix Fietkau. 2) TX skb error handling fix in mt76 driver, also from Felix. 3) Fix BPF_FETCH atomic in x86 JIT, from Brendan Jackman. 4) Avoid double free of percpu pointers when freeing a cloned bpf prog. From Cong Wang. 5) Use correct printf format for dma_addr_t in ath11k, from Geert Uytterhoeven. 6) Fix resolve_btfids build with older toolchains, from Kun-Chuan Hsieh. 7) Don't report truncated frames to mac80211 in mt76 driver, from Lorenzop Bianconi. 8) Fix watcdog timeout on suspend/resume of stmmac, from Joakim Zhang. 9) mscc ocelot needs NET_DEVLINK selct in Kconfig, from Arnd Bergmann. 10) Fix sign comparison bug in TCP_ZEROCOPY_RECEIVE getsockopt(), from Arjun Roy. 11) Ignore routes with deleted nexthop object in mlxsw, from Ido Schimmel. 12) Need to undo tcp early demux lookup sometimes in nf_nat, from Florian Westphal. 13) Fix gro aggregation for udp encaps with zero csum, from Daniel Borkmann. 14) Make sure to always use imp*_ndo_send when necessaey, from Jason A. Donenfeld. 15) Fix TRSCER masks in sh_eth driver from Sergey Shtylyov. 16) prevent overly huge skb allocationsd in qrtr, from Pavel Skripkin. 17) Prevent rx ring copnsumer index loss of sync in enetc, from Vladimir Oltean. 18) Make sure textsearch copntrol block is large enough, from Wilem de Bruijn. 19) Revert MAC changes to r8152 leading to instability, from Hates Wang. 20) Advance iov in 9p even for empty reads, from Jissheng Zhang. 21) Double hook unregister in nftables, from PabloNeira Ayuso. 22) Fix memleak in ixgbe, fropm Dinghao Liu. 23) Avoid dups in pkt scheduler class dumps, from Maximilian Heyne. 24) Various mptcp fixes from Florian Westphal, Paolo Abeni, and Geliang Tang. 25) Fix DOI refcount bugs in cipso, from Paul Moore. 26) One too many irqsave in ibmvnic, from Junlin Yang. 27) Fix infinite loop with MPLS gso segmenting via virtio_net, from Balazs Nemeth. * git://git.kernel.org:/pub/scm/linux/kernel/git/netdev/net: (164 commits) s390/qeth: fix notification for pending buffers during teardown s390/qeth: schedule TX NAPI on QAOB completion s390/qeth: improve completion of pending TX buffers s390/qeth: fix memory leak after failed TX Buffer allocation net: avoid infinite loop in mpls_gso_segment when mpls_hlen == 0 net: check if protocol extracted by virtio_net_hdr_set_proto is correct net: dsa: xrs700x: check if partner is same as port in hsr join net: lapbether: Remove netif_start_queue / netif_stop_queue atm: idt77252: fix null-ptr-dereference atm: uPD98402: fix incorrect allocation atm: fix a typo in the struct description net: qrtr: fix error return code of qrtr_sendmsg() mptcp: fix length of ADD_ADDR with port sub-option net: bonding: fix error return code of bond_neigh_init() net: enetc: allow hardware timestamping on TX queues with tc-etf enabled net: enetc: set MAC RX FIFO to recommended value net: davicom: Use platform_get_irq_optional() net: davicom: Fix regulator not turned off on driver removal net: davicom: Fix regulator not turned off on failed probe net: dsa: fix switchdev objects on bridge master mistakenly being applied on ports ... -
git://git.kernel.org:/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds authored
Pull sparc fixes from David Miller: "Fix opcode filtering for exceptions, and clean up defconfig" * git://git.kernel.org:/pub/scm/linux/kernel/git/davem/sparc: sparc: sparc64_defconfig: remove duplicate CONFIGs sparc64: Fix opcode filtering in handling of no fault loads
-
Corentin Labbe authored
After my patch there is CONFIG_ATA defined twice. Remove the duplicate one. Same problem for CONFIG_HAPPYMEAL, except I added as builtin for boot test with NFS. Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Fixes: a57cdeb3 ("sparc: sparc64_defconfig: add necessary configs for qemu") Signed-off-by:
Corentin Labbe <clabbe@baylibre.com> Signed-off-by:
-
Rob Gardner authored
is_no_fault_exception() has two bugs which were discovered via random opcode testing with stress-ng. Both are caused by improper filtering of opcodes. The first bug can be triggered by a floating point store with a no-fault ASI, for instance "sta %f0, [%g0] #ASI_PNF", opcode C1A01040. The code first tests op3[5] (0x1000000), which denotes a floating point instruction, and then tests op3[2] (0x200000), which denotes a store instruction. But these bits are not mutually exclusive, and the above mentioned opcode has both bits set. The intent is to filter out stores, so the test for stores must be done first in order to have any effect. The second bug can be triggered by a floating point load with one of the invalid ASI values 0x8e or 0x8f, which pass this check in is_no_fault_exception(): if ((asi & 0xf2) == ASI_PNF) An example instruction is "ldqa [%l7 + %o7] #ASI 0x8f, %f38", opcode CF95D1EF. Asi values greater than 0x8b (ASI_SNFL) are fatal in handle_ldf_stq(), and is_no_fault_exception() must not allow these invalid asi values to make it that far. In both of these cases, handle_ldf_stq() reacts by calling sun4v_data_access_exception() or spitfire_data_access_exception(), which call is_no_fault_exception() and results in an infinite recursion. Signed-off-by:Rob Gardner <rob.gardner@oracle.com> Tested-by:
Anatoly Pugachev <matorola@gmail.com> Signed-off-by:
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: fixes 2021-03-09 please apply the following patch series to netdev's net tree. This brings one fix for a memleak in an error path of the setup code. Also several fixes for dealing with pending TX buffers - two for old bugs in their completion handling, and one recent regression in a teardown path. ==================== Signed-off-by:
-
