Instead of old unsafe batostr function use %pMR print specifier
for printing Bluetooth addresses in sprintf and seq_printf
statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Instead of old unsafe batostr function use %pMR print specifier
for printing Bluetooth addresses in debug and error statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The unpair process tries to disconnect any connection pending with
remote. If there are some connection in connecting state, disconnect
command will fail and unpair mgmt command will stay pending.

That pending mgmt command can cause strange behavior like automatic
unpair after a lost connection.
Signed-off-by: Jefferson Delfes <jefferson.delfes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

We just need to use the right modifiers
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving HCI Command Status event for Accept Physical Link
execute HCI Write Remote AMP Assoc with data saved from A2MP Create
Physical Link Request.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving A2MP Create Physical Link message execute HCI
Accept Physical Link command to AMP controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Channel Selected event indicates that link information data is available.
Read it with Read Local AMP Assoc command. The data shall be sent in the
A2MP Create Physical Link Request.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When there is no remote AMP controller found fallback to normal
L2CAP sequence.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving HCI Command Status after HCI Create Physical Link
execute HCI Write Remote AMP Assoc command to AMP controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving A2MP Get AMP Assoc Response execute HCI Create Physical
Link to AMP controller. Define function which will run when receiving
HCI Command Status.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Function calculates AMP keys using hmac_sha256 helper. Calculated keys
are Generic AMP Link Key (gamp) and Dedicated AMP Link Key with
keyID "802b" for 802.11 PAL.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

hmac(sha256) will be used for AMP key generation.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Choose which L2CAP connection to establish by checking support
for HS and remote side supported features.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving A2MP Get AMP Assoc Response save assoc data to remote
AMP controller list and prepare for creating physical link.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Process A2MP Getinfo Response, send Get AMP Assoc Req.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Use hci_conn structure to keep track about AMP physical connections.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Create remote AMP controllers structure. It is used to keep information
about discovered remote AMP controllers by A2MP protocol.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Define physical link structures. Physical links are represented by
hci_conn structure. For BR/EDR we use type ACL_LINK and for AMP
we use AMP_LINK.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving A2MP Discover Response send A2MP Get Info Request
for each AMP controller in the discovery list.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving A2MP Get AMP Assoc Request execute Read Local AMP Assoc
HCI command to AMP controller. If the AMP Assoc data is larger than it
can fit to HCI event only fragment is read. When all fragments are read
send A2MP Get AMP Assoc Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When receiving A2MP Get Info Request execute Read Local AMP Info HCI
command to AMP controller with function to be executed upon receiving
command complete event. Function will handle A2MP Get Info Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Create amp_mgr_list global list which will be used by different
hci devices to find amp_mgr.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Add a few definitions to hci.h
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Hardware support for MFP is not available in ath5k. Thus,
this implementation allows the mac80211 stack to do the
actuall crypto operation.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.

While the documentation hints that there's some
hardware support for offloading MFP "decryption",
this simple implementation relies on the mac80211
stack to do the actual crypto operations.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.

Note:

As all current (and old) firmwares corrupt
incoming, protected management frames, the
decryption offloading needs to be disabled.
This will be done automatically if needed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of copying from a constant array
(which is still needed for other purposes)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Building the libipw component without CONFIG_LIBIPW_DEBUG set triggers this GCC
warning:
    drivers/net/wireless/ipw2x00/libipw_wx.c:526:21: warning: unused variable 'dev' [-Wunused-variable]

The cause of this warning is that, without CONFIG_LIBIPW_DEBUG set,
LIBIPW_DEBUG_WX compiles away. Fix it by substituting ieee->dev for (its
equivalent) dev.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Jack <x6719620@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently scan operation is delayed/aborted based on Tx traffic
consistency. This decision is taken after receiving scan
response of first scan command from FW. But when heavy traffic
is running, we can not even afford to send first scan command
and go off channel for 30msec. We will block scan request in
this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

By default, device is disconnected before entering suspend state.
User can keep the connection alive by using module parameter
"disconect_on_suspend=0".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Field 'pub' in struct brcmf_cfg80211_priv was types as void pointer
and filled with parameter passed in brcmf_cfg80211_attach(). This
patch makes the type specific, ie. struct brcmf_pub.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Small step to fix structure commenting using kernel-doc syntax.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On a usb error the lock bit should be cleared.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug when device is being started
while RfKill switch is engaged, leading to hang
due to partial initialization of hardware.

Tested-by: <dragonn@op.pl>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

clean up code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug in routine where phy bands are determined.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

clean up code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

SDIO read non-glomming frame routine handles first frame and
follow up frame read separately. But they share a lot of common
code. This patch abstracts a brcmf_sdio_hdparser function and
optimize the code flow for better readability and future
optimization.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For suspend/resume it is necessary to store firmware in memory.
In order to support multiple usb dongles at the same time a linked
list of firmwares was created.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>