Merge tag 'linux-can-fixes-for-4.15-20171208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-12-08

this is a pull request of 6 patches for net/master.

Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.15

Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.

iwlwifi

* fix rate-scaling to not start lowest possible rate

* fix the TX queue hang detection for AP/GO modes

* fix the TX queue hang timeout in monitor interfaces

* fix packet injection

* remove a wrong error message when dumping PCI registers

* fix race condition with RF-kill

* tell mac80211 when the MIC has been stripped (9000 series)

* tell mac80211 when the IVC has been stripped (9000 series)

* add 2 new PCI IDs, one for 9000 and one for 22000

* fix a queue hang due during a P2P Remain-on-Channel operation

brcmfmac

* fix a race which sometimes caused a crash during sdio unbind

* fix a kernel-doc related build error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.

Fixes: 1d7d15d7 ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp: RACK loss recovery bug fixes

This patch set has four minor bug fixes in TCP RACK loss recovery.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

RACK skips an ACK unless it advances the most recently delivered
TX timestamp (rack.mstamp). Since RACK also uses the most recent
RTT to decide if a packet is lost, RACK should still run the
loss detection whenever the most recent RTT changes. For example,
an ACK that does not advance the timestamp but triggers the cwnd
undo due to reordering, would then use the most recent (higher)
RTT measurement to detect further losses.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RACK should mark a packet lost when remaining wait time is zero.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sender detects spurious retransmission, all packets
marked lost are remarked to be in-flight. However some may
be considered lost based on its timestamps in RACK. This patch
forces RACK to re-evaluate, which may be skipped previously if
the ACK does not advance RACK timestamp.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RACK does not test the loss recovery state correctly to compute
the reordering window. It assumes if lost_out is zero then TCP is
not in loss recovery. But it can be zero during recovery before
calling tcp_rack_detect_loss(): when an ACK acknowledges all
packets marked lost before receiving this ACK, but has not yet
to discover new ones by tcp_rack_detect_loss(). The fix is to
simply test the congestion state directly.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After applying 2270bc5d ("bnxt_en: Fix netpoll handling") and
903649e7 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
  bnxt_poll+0x0/0xd0 exceeded budget in poll
  <snip>
  Call Trace:
   [<ffffffff814be5cd>] dump_stack+0x4d/0x70
   [<ffffffff8107e013>] __warn+0xd3/0xf0
   [<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
   [<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
   [<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
   [<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
   [<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
   [<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
   [<ffffffff810c9549>] console_unlock+0x339/0x5b0
   [<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
   [<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
   [<ffffffff81173df5>] printk+0x48/0x50
   [<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
   [<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
   [<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
   [<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
   [<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
   [<ffffffff81095f8b>] process_one_work+0x19b/0x480
   [<ffffffff810967ca>] worker_thread+0x6a/0x520
   [<ffffffff8109c7c4>] kthread+0xe4/0x100
   [<ffffffff81884c52>] ret_from_fork+0x22/0x40

This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neal Cardwell says:

====================
TCP BBR sampling fixes for loss recovery undo

This patch series has a few minor bug fixes for cases where spurious
loss recoveries can trick BBR estimators into estimating that the
available bandwidth is much lower than the true available bandwidth.
In both cases the fix here is to just reset the estimator upon loss
recovery undo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix BBR so that upon notification of a loss recovery undo BBR resets
long-term bandwidth sampling.

Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
can cause BBR to spuriously estimate that we are seeing loss rates
high enough to trigger long-term bandwidth estimation. To avoid that
problem, this commit resets long-term bandwidth sampling on loss
recovery undo events.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix BBR so that upon notification of a loss recovery undo BBR resets
the full pipe detection (STARTUP exit) state machine.

Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
could previously cause BBR to spuriously estimate that the pipe is
full.

Since spurious loss recovery means that our overall sending will have
slowed down spuriously, this commit gives a flow more time to probe
robustly for bandwidth and decide the pipe is really full.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit records the "full bw reached" decision in a new
full_bw_reached bit. This is a pure refactor that does not change the
current behavior, but enables subsequent fixes and improvements.

In particular, this enables simple and clean fixes because the full_bw
and full_bw_cnt can be unconditionally zeroed without worrying about
forgetting that we estimated we filled the pipe in Startup. And it
enables future improvements because multiple code paths can be used
for estimating that we filled the pipe in Startup; any new code paths
only need to set this bit when they think the pipe is full.

Note that this fix intentionally reduces the width of the full_bw_cnt
counter, since we have never used the most significant bit.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.

efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.

Fixes: e9117e50 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark tcp_sock during a SACK reneging event and invalidate rate samples
while marked. Such rate samples may overestimate bw by including packets
that were SACKed before reneging.

< ack 6001 win 10000 sack 7001:38001
< ack 7001 win 0 sack 8001:38001 // Reneg detected
> seq 7001:8001 // RTO, SACK cleared.
< ack 38001 win 10000

In above example the rate sample taken after the last ack will count
7001-38001 as delivered while the actual delivery rate likely could
be much lower i.e. 7001-8001.

This patch adds a new field tcp_sock.sack_reneg and marks it when we
declare SACK reneging and entering TCP_CA_Loss, and unmarks it after
the last rate sample was taken before moving back to TCP_CA_Open. This
patch also invalidates rate samples taken while tcp_sock.is_sack_reneg
is set.

Fixes: b9f64820 ("tcp: track data delivery rate for a TCP connection")
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).

This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.

Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Daniel Borkmann says:

====================
pull-request: bpf 2017-12-06

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fixing broken uapi for BPF tracing programs for s390 and arm64
   architectures due to pt_regs being in-kernel only, and not part
   of uapi right now. A wrapper is added that exports pt_regs in
   an asm-generic way. For arm64 this maps to existing user_pt_regs
   structure and for s390 a user_pt_regs structure exporting the
   beginning of pt_regs is added and uapi-exported, thus fixing the
   BPF issues seen in perf (and BPF selftests), all from Hendrik.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".

Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.

Fixes: 32f7adf6 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I switched rcv_rtt_est to high resolution timestamps, I forgot
that tp->tcp_mstamp needed to be refreshed in tcp_rcv_space_adjust()

Using an old timestamp leads to autotuning lags.

Fixes: 645f4c6f ("tcp: switch rcv_rtt_est and rcvq_space to high resolution timestamps")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 28033ae4 ("net: netlink: Update attr validation to require
exact length for some types") requires attributes using types NLA_U* and
NLA_S* to have an exact length. This change is exposing bugs in various
userspace commands that are sending attributes with an invalid length
(e.g., attribute has type NLA_U8 and userspace sends NLA_U32). While
the commands are clearly broken and need to be fixed, users are arguing
that the sudden change in enforcement is breaking older commands on
newer kernels for use cases that otherwise "worked".

Relax the validation to print a warning mesage similar to what is done
for messages containing extra bytes after parsing.

Fixes: 28033ae4 ("net: netlink: Update attr validation to require exact length for some types")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 8d79266b ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
introduced new exit point in  ipxip6_rcv. however rcu_read_unlock is
missing there. this diff is fixing this

v1->v2:
 instead of doing rcu_read_unlock in place, we are going to "drop"
 section (to prevent skb leakage)

Fixes: 8d79266b ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Signed-off-by: Nikita V. Shirokov <tehnerd@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
mv88e6xxx error patch fixes

While trying to bring up a new PHY on a board, i exercised the error
paths a bit, and discovered some bugs. The unwind for interrupt
handling deadlocks, and the MDIO code hits a BUG() when a registered
MDIO device is freed without first being unregistered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO busses need to be unregistered before they are freed,
otherwise BUG() is called. Add a call to the unregister code if the
registration fails, since we can have multiple busses, of which some
may correctly register before one fails. This requires moving the code
around a little.

Fixes: a3c53be5 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When removing the interrupt handling code, we should mask the
generation of interrupts. The code however unmasked all
interrupts. This can then cause a new interrupt. We then get into a
deadlock where the interrupt thread is waiting to run, and the code
continues, trying to remove the interrupt handler, which means waiting
for the thread to complete. On a UP machine this deadlocks.

Fix so we really mask interrupts in the hardware. The same error is
made in the error path when install the interrupt handling code.

Fixes: 3460a577 ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 3d604da1 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'iwlwifi-for-kalle-2017-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Third batch of iwlwifi patches intended for 4.15.

* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.

When I run make W=1 on gcc (Debian 7.2.0-16) 7.2.0 I got an error for
the first run, all next ones are okay.

  CC [M]  drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:2078: error: Cannot parse struct or union!
scripts/Makefile.build:310: recipe for target 'drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o' failed

Seems like something happened with W=1 and wrong kernel doc format.
As a quick fix remove dubious /** in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a fix for syzkaller719569, where memory registration was
attempted without any underlying transport being loaded.

Analysis of the case reveals that it is the setsockopt() RDS_GET_MR
(2) and RDS_GET_MR_FOR_DEST (7) that are vulnerable.

Here is an example stack trace when the bug is hit:

BUG: unable to handle kernel NULL pointer dereference at 00000000000000c0
IP: __rds_rdma_map+0x36/0x440 [rds]
PGD 2f93d03067 P4D 2f93d03067 PUD 2f93d02067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: bridge stp llc tun rpcsec_gss_krb5 nfsv4
dns_resolver nfs fscache rds binfmt_misc sb_edac intel_powerclamp
coretemp kvm_intel kvm irqbypass crct10dif_pclmul c rc32_pclmul
ghash_clmulni_intel pcbc aesni_intel crypto_simd glue_helper cryptd
iTCO_wdt mei_me sg iTCO_vendor_support ipmi_si mei ipmi_devintf nfsd
shpchp pcspkr i2c_i801 ioatd ma ipmi_msghandler wmi lpc_ich mfd_core
auth_rpcgss nfs_acl lockd grace sunrpc ip_tables ext4 mbcache jbd2
mgag200 i2c_algo_bit drm_kms_helper ixgbe syscopyarea ahci sysfillrect
sysimgblt libahci mdio fb_sys_fops ttm ptp libata sd_mod mlx4_core drm
crc32c_intel pps_core megaraid_sas i2c_core dca dm_mirror
dm_region_hash dm_log dm_mod
CPU: 48 PID: 45787 Comm: repro_set2 Not tainted 4.14.2-3.el7uek.x86_64 #2
Hardware name: Oracle Corporation ORACLE SERVER X5-2L/ASM,MOBO TRAY,2U, BIOS 31110000 03/03/2017
task: ffff882f9190db00 task.stack: ffffc9002b994000
RIP: 0010:__rds_rdma_map+0x36/0x440 [rds]
RSP: 0018:ffffc9002b997df0 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff882fa2182580 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffc9002b997e40 RDI: ffff882fa2182580
RBP: ffffc9002b997e30 R08: 0000000000000000 R09: 0000000000000002
R10: ffff885fb29e3838 R11: 0000000000000000 R12: ffff882fa2182580
R13: ffff882fa2182580 R14: 0000000000000002 R15: 0000000020000ffc
FS:  00007fbffa20b700(0000) GS:ffff882fbfb80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000c0 CR3: 0000002f98a66006 CR4: 00000000001606e0
Call Trace:
 rds_get_mr+0x56/0x80 [rds]
 rds_setsockopt+0x172/0x340 [rds]
 ? __fget_light+0x25/0x60
 ? __fdget+0x13/0x20
 SyS_setsockopt+0x80/0xe0
 do_syscall_64+0x67/0x1b0
 entry_SYSCALL64_slow_path+0x25/0x25
RIP: 0033:0x7fbff9b117f9
RSP: 002b:00007fbffa20aed8 EFLAGS: 00000293 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 00000000000c84a4 RCX: 00007fbff9b117f9
RDX: 0000000000000002 RSI: 0000400000000114 RDI: 000000000000109b
RBP: 00007fbffa20af10 R08: 0000000000000020 R09: 00007fbff9dd7860
R10: 0000000020000ffc R11: 0000000000000293 R12: 0000000000000000
R13: 00007fbffa20b9c0 R14: 00007fbffa20b700 R15: 0000000000000021

Code: 41 56 41 55 49 89 fd 41 54 53 48 83 ec 18 8b 87 f0 02 00 00 48
89 55 d0 48 89 4d c8 85 c0 0f 84 2d 03 00 00 48 8b 87 00 03 00 00 <48>
83 b8 c0 00 00 00 00 0f 84 25 03 00 0 0 48 8b 06 48 8b 56 08

The fix is to check the existence of an underlying transport in
__rds_rdma_map().
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Macvlan devices are similar to vlans and do not update their
own trans_start. In order for arp monitoring to work for a bond device
when the slaves are macvlans, obtain its real device.
Signed-off-by: Chris Dion <christopher.dion@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using a period after a newline causes bad output.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offload IP header checksum to NIC.

This fixes a previous patch which disabled checksum offloading
for both IPv4 and IPv6 packets.  So L3 checksum offload was
getting disabled for IPv4 pkts.  And HW is dropping these pkts
for some reason.

Without this patch, IPv4 TSO appears to be broken:

WIthout this patch I get ~16kbyte/s, with patch close to 2mbyte/s
when copying files via scp from test box to my home workstation.

Looking at tcpdump on sender it looks like hardware drops IPv4 TSO skbs.
This patch restores performance for me, ipv6 looks good too.

Fixes: fa6d7cb5 ("net: thunderx: Fix TCP/UDP checksum offload for IPv6 pkts")
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This changes calling conventions (and simplifies the hell out
the callers).  New rules: once struct socket had been passed
to sock_alloc_file(), it's been consumed either by struct file
or by sock_release() done by sock_alloc_file().  Either way
the caller should not do sock_release() after that point.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>