This patch uses clocksource_of_init() call for DT targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Most peripherals on the i.MX53 have an
  Off-Platform Peripheral Access Control Register (OPACR)
in which the access rights (together with the MPROT registers) can be declared.
However, this does not seem to work for example for SSI1+SDMA, because the
supervisor bit is not set for the SDMA unit.
It does work for SSI2, the QSB for example uses SSI2 for its audio. But SSI2 only
works because it does NOT have an OPACR.

The right solution would be to fix the access rights for the SDMA, but the unit
responsible for this is the Central Security Unit (CSU), which of course is NOT
documented. So, until documentation for this is openly available, turn off the
supervisor protection because it cripples the hardware.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The i.MX SoCs allow to setup fine grained access rights to peripherals on the
AIPS bus.
This is done via the Peripheral Access Register (PAR) in e.g. the i.MX21
or in later SoC versions the Off-Platform Peripheral Access Control Register
(OPACR), e.g. i.MX53.
Under certain circumstances this leads to problems in which bus masters are
not granted their access rights to peripherals.
To be able to disable these restrictions on DT platforms, add a helper function
that looks for AIPS nodes in the DT and disables them for every compatible node
it finds.
The compatible has to be declared in the mach-specific entry file, where this
helper function should then be called.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch adds missing 26 MHz oscillator circuit clock gate support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch removes definitions which not used anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Use clock defines in order to make devicetrees more human readable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board.
However, the support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch removes excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27.
Instead we use SOC_IMX*.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

i.MX1 camera driver has been removed by the commit 90b05589.
This patch removes remaining support files for this camera.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

replace IS_ERR/PTR_ERR

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

There could be some memory map devices located in
a certain chip select region of the i.MX WEIM.
The devices could be attached to a simple bus(for
example, a AXI bus) whose root node is one child
device tree node of the i.MX WEIM device tree node.
There should be a bridge(very likely, software
transparent) bewteen the i.MX WEIM and the simple bus.
This patch makes the i.MX WEIM driver possible to
populate devices on a simple bus.  In this way, people
may try various IPs(in a FPGA, maybe) outside of i.MX
chips with the i.MX WEIM embedded.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

imx6q_pm_enter calls imx6sl_set_wait_clk when run on an imx6sl
based machine. However if support for imx6sl is not enabled
at compile time, this prevents us from building the kernel and
we get this link error instead:

arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
:(.text+0x4b84): undefined reference to `imx6sl_set_wait_clk'

This makes the cpu_is_imx6sl function conditionally return false
if imx6sl is disabled at compile-time, which matches what the
older cpu_is_mx* macros did. We have similar inline functions for
the other imx6 variants, but so far I have not run into a case
where the extra #ifdef is necessary.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Building a kernel for imx6sx but without imx6q support results in
this link error because of the missing cpuidle driver:

arch/arm/mach-imx/built-in.o: In function `imx6sx_init_late'::(.init.text+0xc228):
 undefined reference to `imx6q_cpuidle_init'

This patch adds a Makefile entry so we always build support for
the imx6q_cpuidle code when at least one of the 6sx or 6q variants
are enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The PL310 integrated on i.MX6 series and VF610 are revision r3p1 and
later.  Per ARM PL310 errata document, 588369 is fixed in r2p0 and
727915 is fixed in r3p1.  Neither is needed for i.MX6 or VF610.  So
let's drop them.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add EDMA for DMA support for Vybrid SoCs. Also add printk time.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

SSI and SSI_IPG are clocks controlled by the same clock gating field, so
register them with imx_clk_gate2_shared.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Enable STMPE gpio support as this is used on MX6 Data Modul edm-qmx6
board.
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Otherwise GCC will mark the .init.rodata section R/W, which causes
a compile error once we add other real R/O data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

It is only the mx6quad variant that can run up to 1.2GHz, so add the check
accordingly.

This avoids getting the following warning on a mx6solo:

failed to disable 1.2 GHz OPP
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Allow USB device to work by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Replace .init_time() hook with of_clk_init() for DT targets.

Based on:
  d4347ee ARM: i.MX27 clk: Use of_clk_init() for DT case
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The gpt0 timer clock has been wrong since:
  6bbaec56 ARM i.MX25: implement clocks using common clock framework
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch adds devicetree support CCM module for i.MX21 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This is a cleanup for i.MX21 clk driver. This change includes:
- Reduce license text.
- Remove unused definitions.
- Remove unused #include and sort the rest.
- Remove useless comment.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch removes clk_register_clkdev() for the clocks that do not
have any users for boards and drivers.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch perform rework i.MX21 clock initialization. This includes
adding missing clocks and sort clocks by register address.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

mx51 and mx53 are device tree only platforms, so we no longer need all these
calls to clk_register_clkdev().

Only keep cpu0 and gpc_dvfs clk_register_clkdev() calls.

Tested on imx51-babbage and imx53-qsb boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add standby mode support for suspend, to enter standby mode:

echo standby > /sys/power/state;

Use UART or RTC alarm to wake up system, when system enters
standby mode, SOC will enter STOP mode with ARM core kept
power on and 24M XTAL on.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

According to hardware design, mem bit must be clear before
entering DSM mode, as ARM core will be power gated in DSM mode.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Instead of using enum for clock ID, let's switch imx6qdl clock driver to
use macro.  In this case, device tree can reuse these macros to improve
readability.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add cpuidle support for i.MX6SX, derive from i.MX6Q's
cpuidle, two levels supported:

1. WFI;
2. WAIT mode.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add suspend support for i.MX6SX.

To enter suspend, echo mem > /sys/power/state.
To exit suspend, using RTC alarm or enable debug UART wakeup.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board. However, the
support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch adds a reset fallback if base address of watchdog is not set.
This is intended for a targets not compatible with imx-21 watchdog,
i.MX1 for example.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch simplifies handling watchdog clock a bit.
As an additional change, now we properly check WDT clock in a reset
function.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Let mx6sx be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch moves clock check function in common i.MX location
and switch i.MX clk drivers to use this new function.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Replace .init_time() hook with of_clk_init() for DT targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch separates DT and non-DT clock initialization procedure,
so we can avoid a lot of unneeded clk_register_clkdev() for DT case.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>