If the programming of the dev_number fails due to an IO error, a new
device_number will be assigned, resulting in a leak.

Make sure we only assign a device_number once per Slave device.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113225637.17313-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Fix cppcheck warning:

drivers/soundwire/cadence_master.c:992:9: style: Variable 'offset' is
assigned a value that is never used. [unreadVariable]
 offset += stream->num_out;
        ^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113211025.27973-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

make W=1 reports inconsistencies with parameter descriptions, fix
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113211025.27973-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Qualcomm SoundWire Master controller is present in most Qualcomm SoCs
either integrated as part of WCD audio codecs via slimbus or
as part of SOC I/O.

This patchset adds support to a very basic controller which has been
tested with WCD934x SoundWire controller connected to WSA881x smart
speaker amplifiers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200113132153.27239-3-srinivas.kandagatla@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

This patch adds bindings for Qualcomm soundwire controller.

Qualcomm SoundWire Master controller is present in most Qualcomm SoCs
either integrated as part of WCD audio codecs via slimbus or
as part of SOC I/O.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200113132153.27239-2-srinivas.kandagatla@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Before checking for the presence of Device0, we first need to clean-up
the internal state of Slaves that are no longer attached.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

When a Slave reports multiple status in the sticky bits, find the
latest configuration from the mirror of the PING frame status and
update the status directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Config only needs to be updated when setting MCP_Config, MCP_Control
and MCP_CmdCtrl to make these register setting effective. When updating
config in master, master will communicate with slave to update status.
Communication will be failed when masters and slaves are in clock stop
state, and this unnecessary config update makes interrupt setting failed.

Tested on Comet Lake with soundwire enabled
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add the type of command, device number, register offset and length to
reverse engineer what caused the issue.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

make sure all interrupts status are cleared before enabling interrupt
so that there is no unexpected interrupt triggered.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

If somehow we read the interrupt status while the IP is not powered
the result is probably undefined or 0xffffffff. We do know that some
of the bits are reserved and read as zero, so use as a filter to
discard invalid configurations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Only keep pr_err to flag critical configuration errors that will
typically only happen during system integration.

For errors on prepare/deprepare/enable/disable, the caller can do a
much better job with more information on the DAI and device that
caused the issue.
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200108175438.13121-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Due to power rail dependencies, the SoundWire Master driver cannot
make decisions on its own when entering pm runtime suspend.

Add quirk mask for each link, so that the SOF parent driver can inform
the SoundWire master driver of the desired behavior:
a) leave clock on
b) power-off instead of clock stop
c) power-off if all devices cannot generate wakes
d) force bus reset on clock restart

Note that for now the interface with the SOF driver relies on a single
mask for all links. If needed, the interface might be modified at a
later point to provide more freedom. The code at the lower level does
not assume any commonality between links.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-12-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Some of the Intel SoundWire SHIM registers contain fields for
different links. Without protection, the master drivers for the
different links will access these shared registers, leading to invalid
configurations and timeouts (specifically when changing CPA/SPA
power-related registers and polling for the changes to be applied).

A mutex is added to make sure all rmw access to those registers are
serialized.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-11-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

In ClockStop mode, the PCI device will be notified of a wake, which
will be handled from an interrupt thread.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-10-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

In MSI mode, the use of separate handlers and threads for the Intel
IPC, stream and SoundWire shared interrupt leads to timeouts and lost
interrupts.

The solution is to merge all interrupt handling across all links with
a single thread function. The use of a linked list enables this thread
function to walk through all contexts and figure out which link needs
attention.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-9-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The existing use of 6 handlers is problematic in MSI mode. Update
headers so that all shared interrupts can be handled with a single
handler.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The SoundWire DAIs for Intel platform are created in
drivers/soundwire/intel.c, while the communication with the Intel DSP
is all controlled in soc/sof/intel

When the DAI status changes, a callback is used to bridge the gap
between the two subsystems.

The naming of the existing 'config_stream' callback does not map well
with any of ALSA/ASoC concepts. This patch renames it as
'params_stream' to be more self-explanatory.

A new 'free_stream' callback is added in case any resources allocated
in the 'params_stream' stage need to be released. In the SOF
implementation, this is used in the hw_free case to release the DMA
channels over IPC.

These two callbacks now rely on structures which expose the link_id
and alh_stream_id (required by the firmware IPC), instead of a list of
parameters. The 'void *' definitions are changed to use explicit
types, as suggested on alsa-devel during earlier reviews.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The current interfaces between ASoC and SoundWire are limited by the
platform_device infrastructure to an init() and exit() (mapped to the
platform driver.probe and .remove)

To help with the platform detection, machine driver selection and
management of power dependencies between DSP and SoundWire IP, the
ASoC side requires:

a) an ACPI scan helper, to report if any devices are exposed in the
DSDT tables, and if any links are disabled by the BIOS.

b) a probe helper that allocates the resources without actually
starting the bus.

c) a startup helper which does start the bus when all power
dependencies are settled.

d) an exit helper to free all resources

e) an interrupt_enable/disable helper, typically invoked after the
startup helper but also used in suspend routines.

This patch moves all required interfaces to sdw_intel.h, mainly to
allow SoundWire and ASoC parts to be merged separately once the header
files are shared between trees.

To avoid compilation issues, the conflicts in intel_init.c are blindly
removed. This would in theory prevent the code from working, but since
there are no users of the Intel Soundwire driver this has no
impact. Functionality will be restored when the removal of platform
devices is complete.

Support for SoundWire + SOF builds will only be provided once all the
required pieces are upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The Slave device initialization can be split in 4 different cases:

1. Master-initiated hardware reset, system suspend-resume and
pm_runtime based on clock-stop mode1. To avoid timeouts and a bad
audio experience, the Slave device resume operations need to wait for
the Slave device to be re-enumerated and its settings restored.

2. Exit from clock-stop mode0. In this case, the Slave device is
required to remain enumerated and its context preserved while the
clock is stopped, so no re-initialization or wait_for_completion() is
necessary.

3. Slave-initiated pm_runtime D3 transition. With the parent child
relationship, it is possible that a Slave device becomes 'suspended'
while its parent is still 'active' with the bus clock still
toggling. In this case, during the pm_runtime resume operation, there
is no need to wait for any settings to be restored.

4. Slave reset (sync loss or implementation-defined). In that case the
bus remains operational and the Slave device will be re-initialized
when it becomes ATTACHED again.

In previous patches, we suggested the use of wait_for_completion() to
deal with the case #1, but case #2 and #3 do not need any wait.

To account for those differences, this patch adds an unattach_request
field. The field is explicitly set by the Master for the case #1, and
if non-zero the Slave device shall wait on resume. In all other cases,
the Slave resume operations can proceed without wait.

The only request tracked so far is Master HardReset, but the request
is declared as a bit mask for future extensions (if needed). The
definition for this value is added in bus.h and does not need to be
exposed in sdw.h
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Slave drivers may have different ways of handling their settings, with
or without regmap.

During the integration of codec drivers, done in partnership between
Intel and Realtek, it became desirable to implement a predictable
order between low-level initializations performed in .update_status()
(invoked by an interrupt thread) and the settings restored in the
resume steps (invoked by the PM core).

This patch builds on the previous solution to wait for the Slave
device to be fully enumerated. The complete() in this case is signaled
not before the .update_status() is called, but after .update_status()
returns. Without this patch, the settings were not properly restored,
leading to timing-dependent 'no sound after resume' or 'no headset
detected after resume' bug reports.

Depending on how initialization is handled, a Slave device driver may
wait for enumeration_complete, or for initialization_complete, both
are valid synchronization points. They are initialized at the same
time, they only differ on when complete() is invoked.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

When the Master starts the bus (be it during the initial boot or
system resume), it usually performs a HardReset to make sure
electrical levels are correct, then enables the control channel.

While the PM framework guarantees that the Slave devices will only
become 'active' once the Master completes the bus initialization,
there is still a risk of a race condition: the Slave enumeration is
handled in a separate interrupt thread triggered by hardware status
changes, so the Slave device may not be ready to accept commands when
the Slave driver tries to access the registers and restore settings in
its resume or pm_runtime_resume callbacks. In those cases, any
read/write commands from/to the Slave device will result in a timeout.

This patch adds an enumeration_complete structure. When the bus is
goes through a HardReset sequence and restarted, the Slave will be
marked as UNATTACHED, which will result in a call to
init_completion().

When the Slave reports its presence during PING frames as a non-zero
Device, the Master hardware will issue an interrupt and the bus driver
will invoke complete(). The order between init_completion()/complete()
is predictable since this is a Master-initiated transition.

The Slave driver may use wait_for_completion() in its resume callback.
When regmap is used, the Slave driver will typically set its regmap in
cache-only mode on suspend, then on resume block on
wait_for_completion(&enumeration_complete) to guarantee it is safe to
start read/write transactions. It may then exit the cache-only mode
and use a regmap_sync to restore settings. All these steps are
optional, their use completely depends on the Slave device
capabilities and how the Slave driver is implemented.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

When a Slave device becomes synchronized with the bus, it may report
its presence in PING frames, as well as optionally asserting an
in-band PREQ signal.

The bus driver will detect a new Device0, start the enumeration
process and assign it a non-zero device number. The SoundWire
enumeration provides an arbitration to deal with multiple Slaves
reporting ATTACHED at the same time. The bus driver will also invoke
the driver .probe() callback associated with this device. The probe()
depends on the Linux device core, which handles the match operations
and may result in modules being loaded.

Once the non-zero device number is programmed, the Slave will report
its new status in PING frames and the Master hardware will typically
report this status change with an interrupt. At this point, the
.update_status() callback of the codec driver will be invoked (usually
from an interrupt thread or workqueue scheduled from the interrupt
thread).

The first race condition which can happen is between the .probe(),
which allocates the resources, and .update_status() where
initializations are typically handled. The .probe() is only called
once during the initial boot, while .update_status() will be called
for every bus hardware reset and if the Slave device loses
synchronization (an unlikely event but with non-zero probability).

The time difference between the end of the enumeration process and a
change of status reported by the hardware may be as small as one
SoundWire PING frame. The scheduling of the interrupt thread, which
invokes .update_status() is not deterministic, but can be small enough
to create a race condition. With a 48 kHz frame rate and ideal
scheduling cases, the .probe() may be pre-empted within double-digit
microseconds.

Since there is no guarantee that the .probe() completes by the time
.update_status() is invoked as a result of an interrupt, it's not
unusual for the .update_status() to rely on data structures that have
not been allocated yet, leading to kernel oopses.

This patch adds a probe_complete utility, which is used in the
sdw_update_slave_status() routine. The codec driver does not need to
do anything and can safely assume all resources are allocated in its
update_status() callback.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Pull networking fixes from David Miller:

 1) More jumbo frame fixes in r8169, from Heiner Kallweit.

 2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

 3) Use after free in slcan driver, from Jouni Hogander.

 4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

 7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

 8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Pull more SCSI updates from James Bottomley:
 "Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc

Pull cifs fixes from Steve French:
 "Nine cifs/smb3 fixes:

   - one fix for stable (oops during oplock break)

   - two timestamp fixes including important one for updating mtime at
     close to avoid stale metadata caching issue on dirty files (also
     improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
     wire)

   - two fixes for "modefromsid" mount option for file create (now
     allows mode bits to be set more atomically and accurately on create
     by adding "sd_context" on create when modefromsid specified on
     mount)

   - two fixes for multichannel found in testing this week against
     different servers

   - two small cleanup patches"

* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: improve check for when we send the security descriptor context on create
  smb3: fix mode passed in on create for modetosid mount option
  cifs: fix possible uninitialized access and race on iface_list
  cifs: Fix lookup of SMB connections on multichannel
  smb3: query attributes on file close
  smb3: remove unused flag passed into close functions
  cifs: remove redundant assignment to pointer pneg_ctxt
  fs: cifs: Fix atime update check vs mtime
  CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks

Pull misc vfs cleanups from Al Viro:
 "No common topic, just three cleanups".

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  make __d_alloc() static
  fs/namespace: add __user to open_tree and move_mount syscalls
  fs/fnctl: fix missing __user in fcntl_rw_hint()

Pull NTB update from Jon Mason:
 "Just a simple patch to add a new Hygon Device ID to the AMD NTB device
  driver"

* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
  NTB: Add Hygon Device ID

Pull more input updates from Dmitry Torokhov:

 - fixups for Synaptics RMI4 driver

 - a quirk for Goodinx touchscreen on Teclast tablet

 - a new keycode definition for activating privacy screen feature found
   on a few "enterprise" laptops

 - updates to snvs_pwrkey driver

 - polling uinput device for writing (which is always allowed) now works

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
  Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
  Input: goodix - add upside-down quirk for Teclast X89 tablet
  Input: add privacy screen toggle keycode
  Input: uinput - fix returning EPOLLOUT from uinput_poll
  Input: snvs_pwrkey - remove gratuitous NULL initializers
  Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q

Pull iomap fixes from Darrick Wong:
 "Fix a race condition and a use-after-free error:

   - Fix a UAF when reporting writeback errors

   - Fix a race condition when handling page uptodate on fragmented file
     with blocksize < pagesize"

* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: stop using ioend after it's been freed in iomap_finish_ioend()
  iomap: fix sub-page uptodate handling

Pull xfs fixes from Darrick Wong:
 "Fix a couple of resource management errors and a hang:

   - fix a crash in the log setup code when log mounting fails

   - fix a hang when allocating space on the realtime device

   - fix a block leak when freeing space on the realtime device"

* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix mount failure crash on invalid iclog memory access
  xfs: don't check for AG deadlock for realtime files in bunmapi
  xfs: fix realtime file data space leak

Pull orangefs update from Mike Marshall:
 "orangefs: posix open permission checking...

  Orangefs has no open, and orangefs checks file permissions on each
  file access. Posix requires that file permissions be checked on open
  and nowhere else. Orangefs-through-the-kernel needs to seem posix
  compliant.

  The VFS opens files, even if the filesystem provides no method. We can
  see if a file was successfully opened for read and or for write by
  looking at file->f_mode.

  When writes are flowing from the page cache, file is no longer
  available. We can trust the VFS to have checked file->f_mode before
  writing to the page cache.

  The mode of a file might change between when it is opened and IO
  commences, or it might be created with an arbitrary mode.

  We'll make sure we don't hit EACCES during the IO stage by using
  UID 0"

[ This is "posixish", but not a great solution in the long run, since a
  proper secure network server shouldn't really trust the client like this.
  But proper and secure POSIX behavior requires an open method and a
  resulting cookie for IO of some kind, or similar.    - Linus ]

* tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: posix open permission checking...

Pull nfsd updates from Bruce Fields:
 "This is a relatively quiet cycle for nfsd, mainly various bugfixes.

  Possibly most interesting is Trond's fixes for some callback races
  that were due to my incomplete understanding of rpc client shutdown.
  Unfortunately at the last minute I've started noticing a new
  intermittent failure to send callbacks. As the logic seems basically
  correct, I'm leaving Trond's patches in for now, and hope to find a
  fix in the next week so I don't have to revert those patches"

* tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux: (24 commits)
  nfsd: depend on CRYPTO_MD5 for legacy client tracking
  NFSD fixing possible null pointer derefering in copy offload
  nfsd: check for EBUSY from vfs_rmdir/vfs_unink.
  nfsd: Ensure CLONE persists data and metadata changes to the target file
  SUNRPC: Fix backchannel latency metrics
  nfsd: restore NFSv3 ACL support
  nfsd: v4 support requires CRYPTO_SHA256
  nfsd: Fix cld_net->cn_tfm initialization
  lockd: remove __KERNEL__ ifdefs
  sunrpc: remove __KERNEL__ ifdefs
  race in exportfs_decode_fh()
  nfsd: Drop LIST_HEAD where the variable it declares is never used.
  nfsd: document callback_wq serialization of callback code
  nfsd: mark cb path down on unknown errors
  nfsd: Fix races between nfsd4_cb_release() and nfsd4_shutdown_callback()
  nfsd: minor 4.1 callback cleanup
  SUNRPC: Fix svcauth_gss_proxy_init()
  SUNRPC: Trace gssproxy upcall results
  sunrpc: fix crash when cache_head become valid before update
  nfsd: remove private bin2hex implementation
  ...

Pull NFS client updates from Trond Myklebust:
 "Highlights include:

  Features:

   - NFSv4.2 now supports cross device offloaded copy (i.e. offloaded
     copy of a file from one source server to a different target
     server).

   - New RDMA tracepoints for debugging congestion control and Local
     Invalidate WRs.

  Bugfixes and cleanups

   - Drop the NFSv4.1 session slot if nfs4_delegreturn_prepare waits for
     layoutreturn

   - Handle bad/dead sessions correctly in nfs41_sequence_process()

   - Various bugfixes to the delegation return operation.

   - Various bugfixes pertaining to delegations that have been revoked.

   - Cleanups to the NFS timespec code to avoid unnecessary conversions
     between timespec and timespec64.

   - Fix unstable RDMA connections after a reconnect

   - Close race between waking an RDMA sender and posting a receive

   - Wake pending RDMA tasks if connection fails

   - Fix MR list corruption, and clean up MR usage

   - Fix another RPCSEC_GSS issue with MIC buffer space"

* tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
  SUNRPC: Capture completion of all RPC tasks
  SUNRPC: Fix another issue with MIC buffer space
  NFS4: Trace lock reclaims
  NFS4: Trace state recovery operation
  NFSv4.2 fix memory leak in nfs42_ssc_open
  NFSv4.2 fix kfree in __nfs42_copy_file_range
  NFS: remove duplicated include from nfs4file.c
  NFSv4: Make _nfs42_proc_copy_notify() static
  NFS: Fallocate should use the nfs4_fattr_bitmap
  NFS: Return -ETXTBSY when attempting to write to a swapfile
  fs: nfs: sysfs: Remove NULL check before kfree
  NFS: remove unneeded semicolon
  NFSv4: add declaration of current_stateid
  NFSv4.x: Drop the slot if nfs4_delegreturn_prepare waits for layoutreturn
  NFSv4.x: Handle bad/dead sessions correctly in nfs41_sequence_process()
  nfsv4: Move NFSPROC4_CLNT_COPY_NOTIFY to end of list
  SUNRPC: Avoid RPC delays when exiting suspend
  NFS: Add a tracepoint in nfs_fh_to_dentry()
  NFSv4: Don't retry the GETATTR on old stateid in nfs4_delegreturn_done()
  NFSv4: Handle NFS4ERR_OLD_STATEID in delegreturn
  ...

We had cases in the previous patch where we were sending the security
descriptor context on SMB3 open (file create) in cases when we hadn't
mounted with with "modefromsid" mount option.

Add check for that mount flag before calling ad_sd_context in
open init.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

Pull VFIO updates from Alex Williamson:

 - Remove hugepage checks for reserved pfns (Ben Luo)

 - Fix irq-bypass unregister ordering (Jiang Yi)

* tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio:
  vfio/pci: call irq_bypass_unregister_producer() before freeing irq
  vfio/type1: remove hugepage checks in is_invalid_reserved_pfn()

Pull more xen updates from Juergen Gross:

 - a patch to fix a build warning

 - a cleanup of no longer needed code in the Xen event handling

 - a small series for the Xen grant driver avoiding high order
   allocations and replacing an insane global limit by a per-call one

 - a small series fixing Xen frontend/backend module referencing

* tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen-blkback: allow module to be cleanly unloaded
  xen/xenbus: reference count registered modules
  xen/gntdev: switch from kcalloc() to kvcalloc()
  xen/gntdev: replace global limit of mapped pages by limit per call
  xen/gntdev: remove redundant non-zero check on ret
  xen/events: remove event handling recursion detection

Merge misc Kconfig updates from Andrew Morton:
 "A number of changes to Kconfig files under lib/ from Changbin Du and
  Krzysztof Kozlowski"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  lib/: fix Kconfig indentation
  kernel-hacking: move DEBUG_FS to 'Generic Kernel Debugging Instruments'
  kernel-hacking: move DEBUG_BUGVERBOSE to 'printk and dmesg options'
  kernel-hacking: create a submenu for scheduler debugging options
  kernel-hacking: move SCHED_STACK_END_CHECK after DEBUG_STACK_USAGE
  kernel-hacking: move Oops into 'Lockups and Hangs'
  kernel-hacking: move kernel testing and coverage options to same submenu
  kernel-hacking: group kernel data structures debugging together
  kernel-hacking: create submenu for arch special debugging options
  kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'

In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().

v2: fix referenced commit id

Fixes: 14012c9f ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>